Dual Car Audio Stereos Installation Instructions

Dual Car Audio Stereos Installation Instructions
XRM405BT
INSTALLATION/OWNER'S MANUAL
AM/FM Receiver with Detachable Face
XRM405BT INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove trim ring from unit.
• Remove 2 transit screws located on top of the unit.
• Insert the supplied keys into the slots as shown, and slide the unit out of the mounting
sleeve.
• Install mounting sleeve into opening, bending tabs to secure.
• Connect wiring harness and antenna. Consult a qualified technician if you are unsure.
• Certain vehicles may require an installation kit and/or wiring
harness adapter (sold separately).
• Test for correct operation and slide into mounting sleeve to secure.
• Snap trim ring into place.
TYPICAL FRONT-LOAD
TYPICAL
FRONT-LOAD
DIN MOUNTING METHOD
DIN MOUNTING
METHOD
2
XRM405BT INSTALLATION
Wiring Diagram
Antenna
Connector
10 AMP
AGC Fuse
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse could
damage the radio.
The XRM405BT uses one
10 amp AGC fuse located
in-line.
3
XRM405BT OPERATION
Control Locations - Receiver
1
18
4
2
17
3
16
4
5
15
14
13
12
11
10
9
8
1
Release
10
Preset 3 / Intro
2
Band / Go Back
11
Preset 2 / Random
3
Volume Knob
12
Preset 1 / Repeat
4
Power / Mute
13
Display
5
USB Port
14
Tune Up
6
Auxiliary Input
15
Tune Down
7
Preset 6 / Folder Up
16
Mode
8
Preset 5 / Folder Down
17
Audio / Menu
9
Preset 4 / Play / Pause
18
Bluetooth Talk
7
6
XRM405BT OPERATION
Control Locations - Remote
1
2
3
4
17
5
16
6
15
7
14
8
13
9
12
10
11
1
Mode
10
Preset 6 / Folder Up
2
Volume Up
11
Mute
3
Power
12
Audio / Menu
4
Select
13
Preset 5 / Folder Down
5
Tune / Track Up
14
Preset 4 / Play / Pause
6
Volume Down
15
Preset 1 / Repeat
7
Band / Go Back
16
Bluetooth Talk
8
Preset 3 / Intro
17
Tune / Track Down
9
Preset 2 / Random
5
XRM405BT OPERATION
General Operation
Faceplate Removal
Power On/Off
Press RELEASE and pull away from the left side to
remove. To re-install, insert right side of faceplate first
then push left side to secure.
Press or any other button to turn the unit on. Press and
hold again to turn the unit off.
Mute
When the unit is on, press momentarily to mute the
audio. Press again to return to previously-selected
volume.
Mode
Press MODE to select between AM/FM, USB, Bluetooth or
auxiliary input modes. Modes of operation are indicated in
the display. USB mode will not appear unless a USB device
is connected.
Display
The radio frequency (tuner mode) or MP3/WMA title/track
information (USB mode) will be shown by default. Press
DISP to display the clock. The default display will return
after five seconds.
When in USB mode, the display will alternate between
track number/elapsed time and available MP3/WMA
information, including file name, song title, artist name,
album name and folder name.
Reset
Press RESET upon initial installation or if abnormal
operation occurs. Reset button is located behind the front
panel.
Set the Clock
Press DISP to display the clock, then press and hold DISP
until the hours will flash. Press TUNE
to adjust the
minutes and TUNE
to adjust the hours.
ll
Auxiliary Input
Volume
6
nn
Insert a 3.5mm connector in the front panel AUX port.
Connect the other end of the 3.5mm connector to the
headphone output of an audio device, MP3 player, etc.
Adjust volume using the volume knob (00-40).
XRM405BT OPERATION
General Operation
Audio / Menu
Press the AUDIO/MENU to select between Bass, Treble,
Balance, Fader, Loudness, Distance and Stereo.
BASS
TREBLE
BALANCE
FADER
LOUDNESS
Bass
Press AUDIO/MENU until BAS appears.
Rotate the volume knob left/right to adjust.
(-7 minimum / +7 maximum)
Treble
Press AUDIO/MENU until TRE appears.
Rotate the volume knob left/right to adjust.
(-7 minimum / +7 maximum)
EQ
STEREO
Balance
Press AUDIO/MENU until BAL appears. Rotate the volume
knob left/right to adjust from 10L (left) to 10R (right). "BAL
EVEN" represents equal balance.
Fader
Press AUDIO/MENU until FAD appears. Rotate the volume knob left/right to adjust from 10R (rear) to 10F (front).
"FADER EVEN" represents equal balance.
Loudness
EQ
Press AUDIO/MENU until LOUD ON or LOUD OFF appears,
then rotate the volume knob to select desired option.
Activating this feature will enhance the bass and treble frequencies when listening to music at low volumes.
Press AUDIO/MENU until EQ appears, then rotate the volume
knob to select between the following preset equalization curves:
FLAT, POP, JAZZ, ROCK and OFF.
Stereo / Mono
Setup Menu
From tuner mode only, press AUDIO/MENU until STEREO
or MONO appears, then rotate the volume knob to select
desired option. Selecting MONO can improve listening in
areas with a weak FM signal.
Press and hold AUDIO/MENU for more than 3 seconds to
access the setup menu. Press AUDIO/MENU momentarily
to select between the menu functions and rotate the volume
knob left/right to adjust or activate the desired function.
Options are outlined on the following page.
7
XRM405BT OPERATION
General Operation - Setup Menu
Menu Function
Auto Station
Store
Local/Distance
Tuning
Tuner
Frequency
Spacing
Subwoofer
Beep
Confirmation
Options
Action
AUTO STORE
Press the volume knob to seek and save 6 strong stations in
the current band. (Tuner mode only)
Activates distance tuning (Tuner mode only).
Activates local tuning for strong station reception only
(Tuner mode only).
Programs the unit to USA tuner spacing.
(200kHz for FM and 10kHz for AM). (Tuner mode only)
Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM). (Tuner mode only)
Enables the subwoofer.
Disables the subwoofer.
Disables the confirmation beep.
Enables the confirmation beep.
Programs unit to automatically rotate through all LED
colors.
Programs unit to use blue LED display.
LOCAL OFF
LOCAL ON
FREQ USA
FREQ EURO
SUBWFR ON
SUBWFR OFF
BEEP OFF
BEEP ON
LED AUTO
BLUE
GREEN
RED
LED Color
Programs unit to use yellow LED display.
PURPLE
Programs unit to use purple LED display.
CYAN
Programs unit to use cyan LED display.
WHITE
Programs unit to use white LED display.
Press and rotate the volume knob to adjust each RGB color
level. After adjustment, that color will appear on the LCD.
BT ON
Enables Bluetooth functionality.
BT OFF
Disables Bluetooth functionality.
ANSWER AUTO
Programs unit to automatically answer every incoming
phone call after 2-3 rings.
ANSWER MANU
button to be pressed
Programs unit to require the
manually to answer incoming phone calls.
Auto Answer
8
Programs unit to use red LED display.
YELLOW
LED ADJ
Bluetooth
Programs unit to use green LED display.
XRM405BT OPERATION
Seek Tuning
Manual Tuning
Band
Storing and Recalling
Station Presets
AM/FM Tuner Operation
Press and hold TUNE nn or TUNE ll to seek to the
next strong station.
nn
ll
Press TUNE
or TUNE
to change radio frequency
up or down one step at a time. Press and hold to advance
quickly.
Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
9
XRM405BT OPERATION
USB Operation
Connecting a USB Device
(sold separately)
Playing Music
Track Select
Fast Forward and
Reverse
Pause
Displaying Information
Repeat
Random
10
To play MP3/WMA files from most USB mass storage
devices, line up the USB connector and insert the USB
device into the USB port.
When a USB device is first connected, “LOAD” will appear in
the display and playback will begin momentarily. Depending
on the number of files and folders, it may take several
seconds for the device to begin playing. If no valid MP3/
WMA files are detected, “NO FILE” will be displayed and the
last mode will be resumed.
ll
Press TRACK
to skip to the beginning of the next
track. Press TRACK
to return to the beginning of the
current track. Pressing TRACK
again skips to the
beginning of the previous track.
nn
ll
nn
nn on the remote
Press and hold TRACK
or TRACK
control to fast forward or reverse a track.
Press
Press
temporarily stop USB playback.
ll// IIII toagain
to resume playback.
ID3 tag and file/folder information will be automatically
changed during playback. Press DISP to view the clock.
Default display will resume after five seconds.
Press RPT to choose between:
• Current Song - Continuously repeats selected track.
• Current Folder - Continuously repeats all files in folder.
Press RDM to choose between:
• Off - Cancels RDM function.
• All Songs - Plays all tracks in random order.
• Current Folder - Plays all tracks in folder in random
order.
XRM405BT OPERATION
USB Operation
Intro
Character Support
Press INT to enter the Intro menu, then turn the volume
knob to select one of the following options:
• Off - Cancels the INT function.
• All Songs - Plays first 10 seconds of each track.
• Current Folder - Plays first 10 seconds of each track in
folder.
Maximum character display information
• Track name – 64 character maximum
• Directory name – 64 character maximum
• *Song title – 64 character maximum
• *Artist name – 64 character maximum
• *Album name – 64 character maximum
*Song title, artist name and album name will only be
displayed if included with the MP3/WMA file.
Media Compatibility
The following types of files are compatible:
• MP3 data
• WMA data
The following types of files are not compatible:
• WMA files that are protected by DRM (Digital Rights Management).
• WMA lossless format
• MP3 PRO format
• MP3 playlists
• WAV format
Playback Order
MP3/WMA playback sequence is based on order the files
are copied to the USB device and begins in the root folder.
Any empty folders or folders that do not include MP3/WMA
files are skipped. Depending on your software, the playback
order may vary.
11
XRM405BT OPERATION
USB Operation
Playback Capacity
• Maximum number of files: 1024
• Maximum number of folders: 512
• Maximum number of folder levels (sub folders): 8
Note: If the number of files/folders exceeds the maximum
outlined above, the additional files/folders will be ignored.
Note: Devices that exceed the maximum number of files or
folders may not function properly.
USB Device Compatibility
Due to the differences of USB devices, some devices may
not be compatible. USB devices must be ‘mass storage
class’ and formatted to the FAT or FAT32 file system in
order to ensure compatibility. USB devices must be 32GB or
smaller in capacity to be compatible.
Additional MP3/WMA
Information
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be
played. Do not attempt to play non-MP3/WMA files with the
MP3/WMA extension.
Sampling Frequency
Rates
MP3
8kHz ~ 48kHz
WMA
8kHz ~ 48kHz
Transfer Bit rates
MP3
WMA
8kbps ~ 320kbps constant
Variable bit rates
8kbps ~ 384kbps constant
Variable bit rates
Note: Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3 Tag Display
ID3 tags Version 1.0 to 2.0
Note: If an invalid ID3 tag version is detected, "NO
SUPPORT" will scroll on the display.
12
XRM405BT INSTALLATION
Bluetooth® Operation
Pairing a Device
Preparation
Pairing a New Device
Before you can use a Bluetooth device, it must be paired and
connected. Make sure that Bluetooth is activated on your
device before you begin the pairing process.
The XRM405BT broadcasts the pairing signal constantly
when no devices are currently connected. Complete the
pairing sequence from your Bluetooth device. Refer to the
owner's manual for your device for more details.
The device name is "DUAL BT" The Bluetooth passcode "1234"
Note: The XRM405BT can be in any mode of operation when
pairing is performed.
Pairing Additional Devices
If a device is currently connected, press and hold
to
disconnect the current device before a new device can be
paired. Then begin the pairing sequence from the new
Bluetooth device.
(Re)Connecting a Paired Device
Most Bluetooth devices support the auto-connect feature, and will connect automatically
if the device is in range when the XRM405BT is powered-on. If your device was previously
paired but does not connect, use these instructions below. Some devices require
authorization to allow the auto connect feature.
• If your most recently connected Bluetooth device becomes disconnected or does not
reconnect, press
from Bluetooth mode to reconnect your mobile device.
• To connect a previously paired device that was not recently connected:
1) If applicable, press and hold
to disconnect any connected mobile devices.
2) From Bluetooth mode, press SELECT. "Paired Devices" will appear on the LCD.
3) Turn the volume knob to cycle through the list of devices.
4) Press SELECT or
to connect to the desired device. It must be in range to connect.
Note: If the Auto Connect setup menu setting is set to OFF, you must press
you device after pairing, and each time the XRM405BT is powered-on.
to connect
Disconnecting a Device
for 3 seconds to disconnect a connected device. The device will remain
Press and hold
paired and appear in the PAIRED DEVICES menu, but not be connected.
13
XRM405BT OPERATION
Bluetooth® Operation
Making a Phone Call
Manual Dialing
• Press
once. "Enter Phone Number" will be shown, then an "_" will appear on the display.
• Using the remote control, enter the phone number using the 0-9 buttons. Press
on the remote control or XRM405BT front panel to begin dialing.
Note: Placing a phone call from your cell phone will also use
the Bluetooth function of the XRM405BT.
Recent Calls List
• Press SELECT from Bluetooth mode to view the 10 most recent phone calls that were dialed, received or missed while connected to the XRM405BT.
• Turn the volume knob to cycle through the recent phone numbers. Press SELECT or
to dial the phone number.
Redialing the last number
To redial the last phone number, press
two times from
Bluetooth mode. Press
again to redial the phone number.
Receiving and Ending Phone Calls
Receiving a Phone Call
Incoming phone calls will automatically appear on the
display and a ring tone will be heard.
Note: The volume of the ring tone depends on the volume
level of the XRM405BT. The incoming ring tone may not be
heard if the volume is set to a low level or mute is activated.
• Press
• Press
to receive the incoming phone call.
to refuse the incoming phone call.
Note: If Auto Answer is set to ON in the setup menu, all
phone calls will be received automatically.
Ending a Phone Call
14
During an active phone call, press
to end a phone call.
If the phone call was received when listening to music in
another mode, the XRM405BT will resume the previous
mode.
XRM405BT OPERATION
Bluetooth® Operation
During a Phone Call
Volume
Microphone Mute
Turn the volume knob to adjust the volume level during a
phone call. Bluetooth mode has a separate volume level
from the main volume of other modes. The XRM405BT will
remember the volume level in Bluetooth mode and always
return to the last volume level for each phone call.
Press MUTE during a phone call to turn the XRM405BT's
external microphone off. Press MUTE again to resume
microphone operation.
Audio Transfer
Press DISP during a phone call to transfer the call from the
XRM405BT to the cell phone. Press DISP again to toggle the
audio back to the XRM405BT.
Call Hold
During a phone call, when there are no additional incoming
calls, press
to place the call on hold. Press
again to
resume the phone call.
Note: Audio transfer, call waiting and call hold must be
supported by the mobile phone and service provider to
function properly.
Bluetooth Setup Menu Options
Function
Options
Bluetooth
BT
(ON/OFF)
Action
Enables/disables Bluetooth functionality.
Auto Answer
AANS
(OFF/ON)
When set to ON, every incoming phone call will automatically be
answered after 2-3 rings. When set to OFF, the
button must
be pressed to answer incoming phone calls.
15
XRM405BT OPERATION
Bluetooth® Operation
Streaming Audio Operation
The XRM405BT supports A2DP (advanced audio distribution profile) wireless streaming
audio from your Bluetooth mobile device directly to your head unit. You can also control
your music from the front panel of the head unit using AVRCP (audio video remote control
profile).
Notes:
• To stream music to your head unit, your mobile device must support the A2DP and
AVRCP Bluetooth profiles. Check the owner's manual of your mobile device for details.
• Streaming audio must be enabled from your mobile device. This option will vary
depending on the device. Some devices allow streaming audio to be disabled.
After pairing, connecting and enabling streaming audio from a compatible mobile device,
begin playing music using the music player on your mobile device. Once the music is
playing, the following functions can be used to control the music:
• The
• The
• The
• The
will skip to the next available audio track.
ll button
button will skip to the previous audio track.
nn
/ II button will toggle between play and pause during playback.
l button will stop the audio playback.
Note: Some Bluetooth devices may not fully support these commands.
16
XRM405BT OPERATION
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
17
XRM405BT OPERATION
Specifications
FM Tuner
Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 10dBf
50dB quieting sensitivity: 25dbu
Stereo separation @ 1kHz: >30dB
Frequency response: 30Hz-13kHz
AM Tuner
Tuning range: 530kHz-1710kHz
Usable sensitivity: <42dBu
Frequency response: 30Hz-2.2kHz
General
Speaker output impedance: 4~8 ohms
Line output voltage: 1.2 Volts RMS
Dimensions: 7" x 6" x 2" (178 x 152 x 50 mm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 18 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 70dBA (reference: 1 watt into 4 ohms)
18
XRM405BT OPERATION
Troubleshooting
Problem
Unit will not turn on (no power)
Unit has power (but no sound)
Cause
Action
Yellow wire not connected or incorrect
voltage Red wire not connected or
incorrect voltage
Black wire not connected
Fuse blown
Speaker wires not connected
Check connections for proper
voltage (11~16VDC)
One or more speaker wires touching
each other or touching chassis ground
Check connection to ground
Replace fuse
Check connections at speakers
Insulate all bare speaker wires
from each other and chassis
ground
Unit blows fuses
Yellow or red wire touching chassis
ground
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Use fuse with correct rating
NO FILE appears on display
No playable MP3/WMA files found on
the device
Check the device for valid
MP3/WMA files
NO SUPPORT appears
on display
An invalid ID3 tag version is present
Version 1.0 to 2.0 ID3 tags are
supported.
Check for pinched wire
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising