IMPACT DRIVER - Power Tools Plus

IMPACT DRIVER - Power Tools Plus
INSTRUCTION MANUAL
IMPACT DRIVER
054-2735-2
TECHNICAL SPECIFICATIONS
4
SAFETY GUIDELINES
5–12
KEY PARTS DIAGRAM
13
ACCESSORIES
14
OPERATING INSTRUCTIONS
15–19
MAINTENANCE
20–21
EXPLODED VIEW
22
PARTS LIST
23
WARRANTY
24–25
Read and understand this instruction manual thoroughly
before using the product. It contains important information
for your safety as well as operating and maintenance
advice.
Keep this instruction manual for future use. Should this
product be passed on to a third party, then this instruction
manual must be included.
This symbol designates that this tool
is listed by with both Canadian and
U.S. requirements by Underwriters
Laboratories.
IMPACT DRIVER 054-2735-2
61TN
E213739
JD2178U
IMPACT DRIVER 054-2735-2
TABLE OF CONTENTS
If any parts are missing or
damaged, or if you have
any questions, please call
our toll-free helpline at
1-800-689-9928.
3
5
Rating
120 V, 60 Hz, AC
Amperes
3.5 AMP
Impact speed
0–3,200 BPM
Torque
1400 in/lbs
Hex drive
1/4” Quick release
Weight
4 lb 7 oz (2.0 kg)
General safety warnings
! WARNING:
Before using this tool or any of its accessories, read this manual and
follow all Safety Rules and Operating Instructions. The important precautions, safeguards and
instructions appearing in this manual are not meant to cover all possible situations. It must be
understood that common sense and caution are factors which cannot be built into the product.
This instruction manual includes the following:
•
•
•
•
General Safety Rules
Specific Safety Rules and Symbols
Functional Description
Assembly
•
•
•
Operation
Maintenance
Accessories
EYE, EAR & LUNG PROTECTION
ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH CSA REQUIREMENTS or
ANSI SAFETY STANDARD Z87.1
FLYING DEBRIS can cause permanent eye damage. Prescription eyeglasses ARE
NOT a replacement for proper eye protection.
! WARNING:
Non-compliant eyewear can cause serious injury if broken during
the operation of a power tool.
! WARNING:
Use hearing protection, particularly during extended periods of
operation of the tool, or if the operation is noisy.
WEAR A DUST MASK THAT IS DESIGNED TO BE USED
WHEN OPERATING A POWER TOOL IN A DUSTY
ENVIRONMENT.
SAVE THESE INSTRUCTIONS FOR REFERENCE
IMPACT DRIVER 054-2735-2
IMPACT DRIVER 054-2735-2
SAFETY GUIDELINES
TECHNICAL SPECIFICATIONS
4
7
! WARNING: Dust that is created by power sanding, sawing, grinding, drilling, and
other construction activities may contain chemicals that are known to cause cancer, birth defects, or
other genetic abnormalities. These chemicals include:
• Lead from lead-based paints
• Crystalline silica from bricks, cement, and other masonry products
• Arsenic and chromium from chemically treated lumber
The level of risk from exposure to these chemicals varies, according to how often this type of work is
performed. In order to reduce exposure to these chemicals, work in a well-ventilated area, and use
approved safety equipment, such as a dust mask that is specifically designed to filter out microscopic
particles.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
Electrical safety
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
Electrical safety
WARNING: To avoid electrical hazards, fire hazards or damage to the tool, use
proper circuit protection.
This tool is wired at the factory for 120 V AC operation. It must be connected to a 120 V AC, 15 A circuit
that is protected by a time-delayed fuse or circuit breaker. To avoid shock or fire, replace power cord
immediately if it is worn, cut or damaged in any way.
Power tool safety
! WARNING: Read all safety warnings and all instructions. Failure to follow the
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the
risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a ground fault circuit interrupter (GFCI) reduces the risk of electric
shock.
Personal safety
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Work area safety
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
SAVE THESE INSTRUCTIONS FOR REFERENCE
IMPACT DRIVER 054-2735-2
Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on
the switch or energizing power tools that have the switch on invites accidents.
SAVE THESE INSTRUCTIONS FOR REFERENCE
IMPACT DRIVER 054-2735-2
SAFETY GUIDELINES
SAFETY GUIDELINES
6
8
SAFETY GUIDELINES
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
Hold power tool by insulated gripping surfaces, because the blade may contact its own cord.
Cutting a “live” wire may make exposed metal parts of the tool “live” and could give the operator an
electric shock.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
Service
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of dust collection can reduce dust-related hazards.
Specific safety rules
! WARNING:
Power tool use and care
Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
Know your impact driver. Read the Owner’s Manual carefully. Learn the
tool’s applications and limitations, as well as the specific potential hazards related to this tool. Following
this rule will reduce the risk of electric shock, fire or serious injury.
Always wear eye protection. Any power tool can throw foreign objects into your eyes and
cause permanent eye damage. ALWAYS wear safety goggles (not glasses) that comply
with ANSI safety standard Z87.1. Everyday glasses have only impact resistant lenses.
They ARE NOT safety glasses.
! WARNING:
Glasses or goggles not in compliance with ANSI Z87.1 could cause
serious injury when they break.
Always use hearing protection when operating the impact driver.
Use only impact sockets and accessories that are designed for use with an impact driver. Do not use
chrome plated sockets and accessories. Chrome plated sockets and accessories are designed for hand
use only and MUST NOT be used with an impact driver. They may shatter and possibly cause serious
injury.
Before each use, check the impact sockets and accessories for excessive wear or cracks. Worn or
damaged sockets or accessories may shatter and possibly cause serious injury. Worn accessories may
allow the socket to come off during operation of the impact driver.
After installing any accessory in the hex drive, pull outward on the accessory to ensure it is properly
installed and cannot be pulled out of the hex drive.
Never use the impact driver as a torque wrench. Always use a torque wrench to adjust the fastener to the
specified torque.
SAVE THESE INSTRUCTIONS FOR REFERENCE
IMPACT DRIVER 054-2735-2
SAVE THESE INSTRUCTIONS FOR REFERENCE
IMPACT DRIVER 054-2735-2
SAFETY GUIDELINES
9
11
Keep the impact driver handle and body clean and free of oil and grease. Always use a clean dry cloth
when cleaning. Do not use solvents, brake fluid, gasoline or other petroleum products to clean the tool.
They will damage the tool.
Do not wear neckties or loose clothing.
When wearing gloves, they must be tight fitting and slip resistant type. Leather gloves offer the best
protection.
Always use two hands when operating the impact driver. Use one hand on the handle and the other on
the front of the tool body.
Never place your hand so it is touching the socket or accessory when the tool is turned ON. Your hand
could be seriously injured.
Always remove the plug from the power source before installing or removing any socket or accessory.
Be ready for components to shift when removing any fastener. The speed of the fastener removal could
cause unexpected shifting of the components.
Extension cord safety
! WARNING:
Keep the extension cord clear of the working area. Position the cord
so it will not get caught on the workpiece, tools or any other obstructions while you are working with the
power tool.
Make sure any extension cord used with this tool is in good condition. When using an extension cord, be
sure to use one of heavy enough gauge to carry the current the tool will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating.
The table below shows the correct size to use according to cord length and nameplate ampere rating. If
in doubt, use the next heavier gauge. The smaller the gauge number the heavier the cord.
Be sure your extension cord is properly wired and in good condition. Always replace a damaged
extension cord or have it repaired by a qualified electrician before using it. Protect your extension cord
from sharp objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your power tools. This circuit must not be less than 14 gauge wire
and should be protected with either a 15 A time delayed fuse or circuit breaker. Before connecting the
power tool to the power source, make sure the switch is in the OFF position and the power source is the
same as indicated on the nameplate. Running at lower voltage will damage the motor.
MINIMUM GAUGE (AWG) EXTENSION CORDS (120 V use only)
Amperage rating
Total length
More
Not more
25'
50'
100'
150'
than
than
(7.5 m)
(15 m)
(30 m)
(45 m)
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not Applicable
SAVE THESE INSTRUCTIONS FOR REFERENCE
IMPACT DRIVER 054-2735-2
SAVE THESE INSTRUCTIONS FOR REFERENCE
IMPACT DRIVER 054-2735-2
SAFETY GUIDELINES
SAFETY GUIDELINES
10
13
Symbols
! WARNING:
KEY PARTS DIAGRAM
SAFETY GUIDELINES
12
Some of the following symbols may appear on the impact driver.
Study these symbols and learn their meaning. Proper interpretation of these symbols will allow
for more efficient and safer operation of this tool.
V …............
A ………...
Hz ………
W ……….
kW ...........
Volts
Amperes
Hertz
Watts
Kilowatts
...
……….. No load speed
……….
........
L ………...
Kg ………
H ………...
N/cm2 .......
Microfarads
Litres
Kilograms
Hours
Newtons per square
centimetre
Pa ……… Pascals
BPM …..
Beats per minute
Min …….
Minutes
S ………... Seconds
or AC …...
..
..
Three-phase alternating
current with neutral
......
Read all safety warnings
and instructions
Alternating or direct current
………. Class II construction
….......... Splash-proof construction
…….. Watertight construction
………. Protective grounding at
grounding terminal, Class I
tools
… Revolutions or reciprocations
per minute
Alternating current
Three-phase alternating
current
Direct current
0
…........... Diameter
………….. Off position
……. Directional arrow
……... Warning symbol
……. Wear your safety glasses
……... Wear hearing protection
IMPACT DRIVER 054-2735-2
No.
Description
No.
Description
1
Air vents
4
Forward/reverse button
2
Handle
5
1/4” hex drive
3
Variable speed trigger switch
IMPACT DRIVER 054-2735-2
15
14
Description
Size
Qty
1/4” hex drive nut
driver
3/16”, 1/4”, 9/32”, 5/16”,
11/32”, 3/8”
6
Screwdriver bit
R1, R2, R3
3
Screwdriver bit
PZ1, PZ2, PZ3
3
Installing screwdriver bits or
nut drivers
! WARNING:
Use only
screwdriver bits that are designed for use
with an impact driver. Do not use chrome plated
sockets and accessories. Chrome plated sockets
and accessories are designed for hand use only
and MUST NOT be used with an impact driver.
They may shatter and possibly cause serious
injury.
! WARNING:
Always remove the
plug from the power source before changing any
sockets, bits or accessories. You may injure your
hand if the tool is started accidentally.
1.
To install a screwdriver bit, pull outward
on the hex drive sleeve (1) (Fig. 1). While
holding the hex drive sleeve out, insert
the bit (2) fully into the hex drive and then
release the outer sleeve.
2.
When the hex drive sleeve is released, pull
outward on the bit to ensure the retaining
balls inside the hex drive are engaged with
the groove in the bit (3) to prevent the bit
from sliding out of the hex drive.
3.
To remove the bit, pull outward on the hex
drive sleeve and pull the bit out of the hex
drive.
fig. 1
! WARNING:
Never use a
screwdriver bit or nut driver that does NOT have
the locking groove. These accessories will not be
adequately held in the hex drive and could come
loose and possibly injure the operator.
IMPACT DRIVER 054-2735-2
IMPACT DRIVER 054-2735-2
OPERATING INSTRUCTIONS
ACCESSORIES
Illustration
16
17
This impact driver is equipped with a forward/
reverse button (1) (Fig. 2).
1.
To operate the impact driver in the forward
direction, press the forward/reverse button
to the LEFT for driving screws or tightening
nuts.
2.
To operate the impact driver in the reverse
direction, press the forward/reverse button
to the RIGHT for removing screws or
removing nuts.
NOTE: Never press the forward/reverse
button while the tool it turned ON. Damage
to the tool will result.
For safety reasons, the operator must read
the sections of this Owner’s Manual entitled
“GENERAL SAFETY WARNINGS”, “POWER
TOOL SAFETY”, “SPECIFIC SAFETY RULES”,
“EXTENSION CORD SAFETY” and “SYMBOLS”
before using this impact driver.
Verify the following every time the impact
driver is used:
1.
2.
Variable speed trigger switch
3.
This tool is equipped with a variable-speed ON/
OFF trigger switch.
1.
2.
To start tool, gently squeeze the trigger
switch (2) (Fig. 3).
NOTE: The tool will turn at its slowest
speed when the trigger switch is depressed
slightly. The tool will turn at its fastest speed
when the trigger switch is fully depressed.
To stop the tool, release the trigger switch.
! WARNING
fig. 2
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Forward/reverse button
fig. 3
Safety glasses and hearing protection
are being worn.
Screwdriver bit or nut driver is “impact
driver” rated.
Screwdriver bit or nut driver s in good
condition.
Failure to observe these safety rules will
significantly increase the risk of injury.
Tightening & removing
fasteners
The most common uses for the impact driver are
to drive or remove screws and to tighten or loosen
small nuts.
The principles for operating the impact driver are
the same for most applications. For illustrative
purposes, driving a wood screw is shown.
IMPACT DRIVER 054-2735-2
IMPACT DRIVER 054-2735-2
19
OPERATING INSTRUCTIONS
Preparing screw holes
It is important to prepare screw holes before
attempting to fasten two pieces of wood together.
Proper preparation will make screws drive easier
and prevent misaligned components, stripped
screw heads, splitting and separating of wood
components.
1.
Clamp components that are to be screwed
together in their desired position (Fig. 4).
2.
Drill a pilot hole (1) through the outer piece
(2) and into the inner piece (3). Drill hole 2/3
the diameter of the smooth portion of the
screw shank.
NOTE: If the wood is soft, drill the hole 2/3
the length of the screw. If the wood is hard,
drill the hole the full length of the screw.
3.
Remove the clamp from the two pieces to
be screwed together.
4.
Enlarge the hole (1) in the outer piece (2) so
it is the same size as the smooth portion of
the screw shank (Fig. 5).
5.
If using a flat head screw, counter-sink the
hole (4) so the head of the screw will be
flush with the surface when fully driven into
place.
Driving screws
When driving screws, care must be taken to use a
bit that correctly fits the head of the screw being
driven. Be sure to use the largest bit size that
will properly fit into the head of the screw. The
bit must also be in good condition and not worn
so it will drive screws without slipping out of the
screw head.
Always hold the impact driver with two hands
when driving and removing screws to provide the
best possible control over the tool.
IMPACT DRIVER 054-2735-2
1.
Select the correct screwdriver bit for the
screw being driven.
2.
Insert the bit into the hex drive (Fig. 1).
3.
Set the forward/reverse button to the LEFT
for driving screws (Fig. 2).
4.
Insert the screwdriver bit (1) fully into the
screw head (3) (Fig. 6).
5.
While holding the impact driver firmly
against the screw with both hands and the
bit aligned with the screw, squeeze the trigger switch and drive the screw.
6.
When the screw is driven to the correct
depth, release the switch and the impact
driver will stop.
fig. 4
fig. 5
fig. 6
NOTE: As the screw is driven into the wood, the
torque required to completely drive the screw into
the wood will increase. The impact function will
allow you to continue driving the screw until it is
fully nested in the countersunk area.
7.
Release the trigger as soon as the screw
is driven to the desired depth. Failure to
release the trigger at this point will result in
an overdriven screw and possibly twist the
head off the screw.
8.
To remove screws, follow the same general
procedure as for driving screws.
9.
Push the forward/reverse button to the
RIGHT for removing screws.
10. Insert the bit fully into the screw head.
11. Hold the impact driver and bit firmly against
the screw head and squeeze the trigger
switch.
NOTE: The impact action will allow you to remove
tight screws.
IMPACT DRIVER 054-2735-2
OPERATING INSTRUCTIONS
18
21
20
General
! WARNING:
When servicing,
use only identical replacement parts. Use of any
other part may create a hazard or cause product
damage.
The carbon motor brushes will wear down and
require replacing. The time intervals between
replacements will vary depending upon the
torques being achieved and the hours of use. It
is recommended that the brushes be checked
after each 10 hours of use. When the length of
the carbon brush reaches 1/4” (6.35 mm), the
brushes should be replaced.
DO NOT use solvents when cleaning plastic
parts. Plastics are susceptible to damage from
various types of commercial solvents and may be
damaged by their use. Use a clean cloth to remove
dirt, dust, oil, grease etc.
! WARNING: Unplug the tool
! WARNING:
from the power source.
1.
Use a 3/16” (4 mm) slot screwdriver and
remove one brush cap (1) (Fig. 7). Turn the
brush cap counter clockwise to remove it
from the motor housing.
2.
Pull the spring & brush assembly (2) from
the brush holder (3) in the motor housing
(4).
3.
Insert the new spring & brush assembly into
the motor housing.
4.
Compress the spring into the brush holder
and thread the brush cap back into the
motor housing.
NOTE: Make sure the brush cap threads are
not cross-threaded. Do NOT over tighten.
5.
Repeat steps 1 to 4 and replace the second
carbon brush located on the opposite side of
the motor housing.
IMPACT DRIVER 054-2735-2
MAINTENANCE
MAINTENANCE
Replacing carbon motor
brushes
fig. 7
Do not at any time
allow brake fluids, gasoline, petroleum-based
products, penetrating oils, etc. to come into
contact with plastic parts. They contain chemicals
that can damage, weaken or destroy plastic.
DO NOT abuse power tools. Abusive practices can
damage the tool as well as the workpiece.
! WARNING:
DO NOT attempt
to modify tools or create accessories. Any such
alteration or modification is misuse and could
result in a hazardous condition leading to possible
serious injury. It will also void the warranty.
Lubrication
All of the bearings in this tool are lubricated with
a sufficient amount of high-grade lubricant for the
life of the unit under normal conditions. Therefore,
no further lubrication is required.
IMPACT DRIVER 054-2735-2
22
23
! WARNING: When servicing, use only Mastercraft
replacement parts. The use of any
other parts may create a safety hazard or cause damage to the impact driver.
Any attempt to repair or replace electrical parts on this impact driver may create a safety hazard unless
repairs are performed by a qualified technician. For more information, call the Toll-free Helpline, at
1-800-689-9928.
Always order by PART NUMBER, not by key number.
IMPACT DRIVER 054-2735-2
Key #
Part #
Part Name
Qty
Key #
Part #
Part Name
Qty
1
2050080131
Fixing ring
1
21
4110050003
Pin
3
2
2030020001
Washer No.1
1
22
2030020229
Washer N0.4
1
3
2050060004
Bushing spring
1
23
4010010084
Bearing 6002-2RS
1
4
2040170001
Bushing
1
24
2010090067
Inner gear ring
1
5
4080030001
Ball 3.5
1
25
3150070079
Gear box
1
6
3140100006
Casting rubber cover
1
26
4010010054
Bearing 6000-2RS
1
7
2020050059
Aluminum casting
1
27
1010180009
Rotor
1
8
4030010114
ST3.9X25
4
28
3150140006
Carbon brush cap
2
9
4040030001
Spring washer 4
4
29
3150060015
Brush holder
2
10
3140020017
“O” ring
1
30
1230010030
Carbon brush
2
11
2010080012
Shaft bushing
1
31
2030070027
Brush holder support
1
12
2030020034
Washer No.2
1
32
4010010053
Bearing 607-2RS
1
13
2040050115
Outer shaft
1
33
1020180008
Stator
1
14
4080070001
Steel ball 5.5
2
34
3011180004
Enclosure
1
15
2040200002
Torsion slot
1
35
3120030017
Direction setting button
1
16
4080040001
Steel ball 4
21
36
1061010002
Switch
1
17
2030020035
Washer No.3
1
37
4030010106
Screw ST3.9X19
8
18
2050060178
Torsion spring
1
38
4030010098
Screw ST3.9X13
2
19
2040050022
Inner shaft
1
39
3140010004
Cord guard
1
20
2010010027
Planetary gear
3
40
1190030012
UL plug cord
1
IMPACT DRIVER 054-2735-2
PARTS LIST
EXPLODED VIEW
®
25
WARRANTY
g.
3
YEAR
ANS
h.
LIMITED WARRANTY†
DE GARANTIE LIMITÉE†
i.
This Mastercraft® product is guaranteed for a period of three years from the date of original retail
purchase against defects in workmanship and materials, except for the following components:
a.
b.
Component A: Batteries, chargers and carrying case, which are guaranteed for a period of two
years from the date of original retail purchase against defects in workmanship and materials;
Component B: Accessories, which are guaranteed for a period of one year from the date of original
retail purchase against defects in workmanship and materials.
Subject to the conditions and limitations described below, this product, if returned to us with proof
of purchase within the stated warranty period and if covered under this warranty, will be repaired or
replaced (with the same model, or one of equal value or specification), at our option. We will bear the cost
of any repair or replacement and any costs of labour relating thereto.
These warranties are subject to the following conditions and
limitations:
a.
b.
c.
d.
e.
f.
A bill of sale verifying the purchase and the purchase date must be provided;
This warranty will not apply to any product or part thereof that is worn, broken or that has become
inoperative due to abuse, misuse, accidental damage, neglect or lack of proper installation,
operation or maintenance (as outlined in the applicable owner’s manual or operating instructions)
or that is being used for industrial, professional, commercial or rental purposes;
This warranty will not apply to normal wear and tear or to expendable parts or accessories that
may be supplied with the product and that are expected to become inoperative or unusable after a
reasonable period of use;
This warranty will not apply to routine maintenance and consumable items, including, but not
limited to, fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids, tune-ups or
adjustments;
This warranty will not apply where damage is caused by repairs made or attempted by others (i.e.:
persons not authorized by the manufacturer);
This warranty will not apply to any product that was sold to the original purchaser as a
reconditioned or refurbished product (unless specified otherwise in writing);
IMPACT DRIVER 054-2735-2
This warranty will not apply to any product or part thereof if any part from another manufacturer
is installed therein or any repairs or alterations have been made or attempted by unauthorized
persons;
This warranty will not apply to normal deterioration of the exterior finish, including, but
not limited to, scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive
and chemical cleaners; and
This warranty will not apply to component parts sold by and identified as the product of another
company, which shall be covered under that product manufacturer’s warranty, if any.
Additional Limitations
This warranty applies only to the original purchaser, and cannot be transferred. Neither the retailer nor
the manufacturer shall be liable for any other expense, loss or damage, including, without limitation, but
not limited to any indirect, incidental, consequential or exemplary damages arising in connection with the
sale, use or inability to use this product.
Notice to Consumer
This warranty gives you specific legal rights, and you may have other rights, which may vary from
province to province. The provisions contained in this warranty are not intended to limit, modify, take
away from, disclaim or exclude any statutory warranties set forth in any applicable provincial or federal
legislation.
Mastercraft is a superior line of products selected for their workmanship and materials. These products
are designed to meet rigorous quality and performance standards, and are approved by our Quality
Assurance laboratory.
TOLL-FREE HELPLINE: 1-800-689-9928
IMPACT DRIVER 054-2735-2
Rev 2.5 19/08/2013
WARRANTY
24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising