Installation manual VBB6
VolvoTech.EU
MANUAL
Kind
Title
Language
Version
Date
Applicable to
Contents
Installation manual
Installation Manual VBB6 MC
English
1.10
November 10th 2013
VBB6 in Volvo V70/XC70/S80/XC60
Manual describes installation of the VBB6 and MiniCam
VOLVOTECH.EU INSTALLATION
VBB6 VERSION 1.1
MANUAL
VBB6 INSTALLATION MANUAL for
V70/XC70/S80/XC60
Applicable to:
VBB6 (VolvoTech’s Video Break-in Box type 6)
Installation manual and description of connections.
Pre requirements for this document to be useful:
-
A Volvo V70,XC70, S80 or XC60 with navigation, up to MY 2011 (NOT FOR
SENSUS!)
-
No known errors or failures in the electronics of your Volvo.
Need to know:
-
Obviously we try to put as much information in a manual as we can.
Sometimes things are “normal” and “of base logic” to us, which might not
be for you, simply because you are not installing electronics in your car
daily, and we are. Please in cases where we seem to miss out on
information in a manual; think logically, measure power and/or contact us!
-
In case you might have any questions, please email us at
support@volvotech.eu
-
There is technically NO difference for LHD cars or RHD cars.
Note that the Camera will always be in the Right side.
-
Please find the reverse light BEFORE you pull cables !
-
Alternatively the connector near the trunk-inside-light can be used for
connection to the reversing power!
-
Page 1 of 13
CopyRight 2012, VolvoTech.EU
C: BE || CD 131110 || V 1.10 || RD 131128 || HC 1 || FC 3.26 ||
VolvoTech-manual-EN-installation-VBB6-MC-1.1.doc
Contact details:
VolvoTech.EU
support@volvotech.eu
VOLVOTECH.EU INSTALLATION
VBB6 VERSION 1.1
MANUAL
CONNECTIONS
Please read carefully before performing installation:
VIDEO 2 Port:
Used for the Rearview
Camera
Power Led:
Should ALLWAYS be on!
VIDEO 1 Port:
Used for any video
playback device,
activated with the
supplied switch
12V Power port:
Connect to the RTI
computer with the
supplied connector set.
SYNC switch:
Set to RGB-S please.
(in YOUR Volvo no
other setting possible)
RTI Port:
Connect to the RTI
computer with the
supplied cable.
RTI Receptable:
Page 2 of 13
Connects
to the
CopyRight 2012, VolvoTech.EU
connector
you need to
C: BE || CD 131110 || V 1.10 || RD 131128 || HC 1 || FC 3.26 ||
remove
from
the RTI
VolvoTech-manual-EN-installation-VBB6-MC-1.1.doc
computer.
Brightness and RESET:
In case the image of
the video port (Video 1)
is to dark, you can set
and change brightness
here. (NOTE : Not
required for a
VolvoTech camera, the
camera adjusts
itselves!)
RESET : Factory default
the VBB4.
Contact details:
VolvoTech.EU
support@volvotech.eu
VBB Power + EOPS:
In case you ordered the
combined EOPS you
can connect any
required switched
power to the RED and
BLACK wire here.
VOLVOTECH.EU INSTALLATION
VBB6 VERSION 1.1
MANUAL
Power connector:
Connects to the Red
and black power lead at
the RTI navi Computer.
(With the supplied POSI
tabs, plug and play!)
VBB4 Connector:
Connects to the RTI
IN/OUT port of the
VBB4.
RTI Receptable:
Connects to the
connector you need to
remove from the RTI
computer.
RTI Connector:
Connects to the RTI
computer, in the port
where you removed the
original grey connector
from.
Green wire ->
If cut, no parking lines!
Camera:
Minicamera type.
Page 3 of 13
CopyRight 2012, VolvoTech.EU
C: BE || CD 131110 || V 1.10 || RD 131128 || HC 1 || FC 3.26 ||
VolvoTech-manual-EN-installation-VBB6-MC-1.1.doc
White wire ->
If cut, image is
mirrored.
(PREFERED!)
Contact details:
VolvoTech.EU
support@volvotech.eu
VOLVOTECH.EU INSTALLATION
VBB6 VERSION 1.1
MANUAL
SCHEMATIC OVERVIEW OF COMPONENTS AND WIRING.
RTI Computer
RTI Connection
harness from VBB4
to RTI computer
(Power and/or
Video)
VBB6
Camera
Rear light unit:
Provides 12V+ and 12V- to
the camera and VBB4 when
car in reverse.
Page 4 of 13
CopyRight 2012, VolvoTech.EU
C: BE || CD 131110 || V 1.10 || RD 131128 || HC 1 || FC 3.26 ||
VolvoTech-manual-EN-installation-VBB6-MC-1.1.doc
Contact details:
VolvoTech.EU
support@volvotech.eu
VOLVOTECH.EU INSTALLATION
VBB6 VERSION 1.1
MANUAL
INSTALLATION
VBB6 (Video Break-in Box type 6)
Remove the 6pin video connector (same as in the supplied set) and the multi-pin
(but only black and red connected) connector from the navi computer.
(Just put your hand down at the left part of the trunk, where the navi computer
is).
Page 5 of 13
CopyRight 2012, VolvoTech.EU
C: BE || CD 131110 || V 1.10 || RD 131128 || HC 1 || FC 3.26 ||
VolvoTech-manual-EN-installation-VBB6-MC-1.1.doc
Contact details:
VolvoTech.EU
support@volvotech.eu
VOLVOTECH.EU INSTALLATION
VBB6 VERSION 1.1
MANUAL
Front
Front
Right
Front
LEFT
Video connector
Front
Power connector
Rear
Front
Page 6 of 13
CopyRight 2012, VolvoTech.EU
C: BE || CD 131110 || V 1.10 || RD 131128 || HC 1 || FC 3.26 ||
VolvoTech-manual-EN-installation-VBB6-MC-1.1.doc
Contact details:
VolvoTech.EU
support@volvotech.eu
VOLVOTECH.EU INSTALLATION
VBB6 VERSION 1.1
MANUAL
Then connect the supplied female connector to the original Video connector and
push the supplied connector into the Navigation computer.
Then connect the power leads to the red (12v+) and black (12V-) wires at the
Navi computer’s power connector.
Page 7 of 13
CopyRight 2012, VolvoTech.EU
C: BE || CD 131110 || V 1.10 || RD 131128 || HC 1 || FC 3.26 ||
VolvoTech-manual-EN-installation-VBB6-MC-1.1.doc
Contact details:
VolvoTech.EU
support@volvotech.eu
VOLVOTECH.EU INSTALLATION
VBB6 VERSION 1.1
MANUAL
Now drill a 7.5 or 8mm whole in the trunk, at the location as shown above.
*(use the supplied sticker now temporarily for drilling guidance/fitting!)
Page 8 of 13
CopyRight 2012, VolvoTech.EU
C: BE || CD 131110 || V 1.10 || RD 131128 || HC 1 || FC 3.26 ||
VolvoTech-manual-EN-installation-VBB6-MC-1.1.doc
Contact details:
VolvoTech.EU
support@volvotech.eu
VOLVOTECH.EU INSTALLATION
VBB6 VERSION 1.1
MANUAL
After the whole is drilled, push the camera in (please already stick the supplied
foam-sticker to the camera but NOT the car side yet!), push the camera in and
connect the bolt onto the nock where the camera-cable comes out.
(picture upside down, since trunk is open at this point of the installation!)
Them guide the cables as shown:
Page 9 of 13
CopyRight 2012, VolvoTech.EU
C: BE || CD 131110 || V 1.10 || RD 131128 || HC 1 || FC 3.26 ||
VolvoTech-manual-EN-installation-VBB6-MC-1.1.doc
Contact details:
VolvoTech.EU
support@volvotech.eu
VOLVOTECH.EU INSTALLATION
VBB6 VERSION 1.1
MANUAL
At te rubber, remove the rubbers from the car gently and from the guidance
keepers.
Then pull the wiring trough the rubber.
(you might need to use a stong piece of metal/plastic to push a pull-wire trough).
Inside the trunk, above the roofpanel, you’ll find this connector.
Please guide the camera harness here to the left side (where the navigation is) of
the car. If you need/want, you can connect the power for the switching/camera
activation here!
Page 10 of 13
CopyRight 2012, VolvoTech.EU
C: BE || CD 131110 || V 1.10 || RD 131128 || HC 1 || FC 3.26 ||
VolvoTech-manual-EN-installation-VBB6-MC-1.1.doc
Contact details:
VolvoTech.EU
support@volvotech.eu
VOLVOTECH.EU INSTALLATION
VBB6 VERSION 1.1
MANUAL
The green/brown wire at the rooftop connector holds the switched 12v+ for the
reverse light.
Now guide the wiring down to the VBB location and connect as set out in the
schedule above and at the stickers on the wires at the set!
Page 11 of 13
CopyRight 2012, VolvoTech.EU
C: BE || CD 131110 || V 1.10 || RD 131128 || HC 1 || FC 3.26 ||
VolvoTech-manual-EN-installation-VBB6-MC-1.1.doc
Contact details:
VolvoTech.EU
support@volvotech.eu
VOLVOTECH.EU INSTALLATION
VBB6 VERSION 1.1
MANUAL
NOW; Run test (put car in ignition position 2 and put car in reverse gear).
Camera should now be activated, RTI image should disappear.
Putting gear back to “neutral” or “P” will make the camera image
disappear and the RTI image to become visible again.
Now close all covers and parts of your car in reverse order.
FAQ
Frequently asked questions
Q: I installed everything correctly, but I do not see my RTI (navigation) image
anymore, what is happening?
A: As the VBB6 has 2 video entries, (1 for RV camera and 1 for any other video),
most probably the switch (Red/Black wired) is in the position it wants to show
video from Video-1. Switching over to the other position will solve this issue.
Q: Everything “works” alright, but the image of the camera is not right, it seems
like some electrical disturbance is taking place.
A: Your car has a screen which uses Negative sync for synchronising the image
nicely on the screen. Setting for this is wrong. Please OPEN the VBB6 and you will
find a “jumper” on pins 1 and 2. Please move the jumper to pins 2 and 3. That
should solve your issue.
Q: Image from camera is really fine and sharp, but image on Video-1 source is
there, but “running” on the screen and very small.
A: Most probably the source you use on Video-1 is set to PAL. The screen in your
car uses NTSC, please switch the device you have connected to NTSC output. That
should solve your issue.
Q: The VBB is always powered, won’t that drain the battery?
A: In the end, obviously it will help drain the battery. But, in “rest” (i.e. no video
source active, screen down) the VBB4 only takes app 15mA of power. This will not
drain your battery far enough so starting is not possible anymore).
Page 12 of 13
CopyRight 2012, VolvoTech.EU
C: BE || CD 131110 || V 1.10 || RD 131128 || HC 1 || FC 3.26 ||
VolvoTech-manual-EN-installation-VBB6-MC-1.1.doc
Contact details:
VolvoTech.EU
support@volvotech.eu
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising