Swash 450 / 550

Swash 450 / 550
Swash 450 / 550
� �
high-tech toilet seat
OWNER'S MANUAL
Round
Elongated
S450-RW / RB, S550-RW / RB
S450-EW / EB, S550-EW / EB
This manual contains important safety information.
Please read it carefully before product installation or use.
NEVER PLUG IN THE PRODUCT BEFORE IT IS COMPLETELY INSTALLED
Important Safeguards
� � � � �� �
For safety reasons, please read this entire manual before use.
� � � � �� �
Danger - Possibility of Electric Shock!
Do not use harsh brushes or abrasive detergents to clean
the Swash 450 / 550. Use only mild soap and a soft cloth
for cleaning.
Please use caution and avoid spraying water directly on the
Swash 450 /550 or power cord. This could result in electric
shock or fire.
Do not disassemble or modify the Swash 450 / 550. Only an
authorized service representative should perform repairs.
Use the correct voltage according to the Specifications and
connect to a three prong GFI grounded outlet.
Specifications
Model
S450-RW / RB S550-RW / RB
S450-EW / EB S550-EW / EB
Rated Power Source
AC 120V 60Hz 1400W
Tap Water Pressure
0.5-7.5 kgf/cm (7 - 106 psi)
�
Rated Power Consumption
1.5 kwh
OFF: room temperature LOW: 36 C (97 F) MED: 38 C (100 F) HIGH: 40 C (104 F)
Seat Temperature
Seat & Lid
Soft Closing
Maximum Spray Volume
0.72 liter / min (0.2 gal / min)
Water Temperature
OFF: room temperature LOW: 36 C (97 F) MED: 38 C (100 F) HIGH: 40 C (104 F)
Dryer Temperature
LOW / MED / HIGH (available in Swash 550)
Electrical Safety Protection
15 mA - GFI
Power Cord Length
1.2 m (4 ft)
17.1"W x 19"L x 6.0" H
433mm W x 483mm L x 153mm H
Product Dimensions
17.1"W x 20"L x 6.0"H
433mm W x 511mm L x 153mm H
3.8 kg (14.8 lbs)
Product Weight
3.9kg (15.4 lbs)
Parts & Configuration
Installed
Configuration
Swash 450 / 550
T-Valve
with Bidet Hose
GFI
Grounded
Outlet
� � � � � �� � �� �� � �
T-Valve
Water
Supply Line
Standard
Mounting Hardware
Alternate
Mounting Hardware
Universal Wrench
1
Water
Shut-Off
Valve
Bidet Hose
Typical install time: 30-60 minutes
Before Installation
Tools Needed
Flat head screwdriver
Univeral Wrench (included)
Phillips screwdriver
Measuring tape
NOTE: The included Universal Wrench will work for most applications. Depending on your toilet
configuration, an adjustable wrench may also be needed.
Alternate Mounting Hardware
Some toilets may not provide adequate access to the seat mounting holes preventing proper installation
of the Standard
Hardware.
�
�� � Mounting
�
In this case, you will need to use� the Alternate Mounting Hardware and follow the enclosed instructions.
Check Water Supply Line
�
�
Check the line that connects the toilet tank to the water shut off valve. If it is a rigid pipe, you may need to
purchase a flexible hose to replace it before installing the Swash 450 / 550. The length of the hose and the
size of the connectors will vary.
Installation
� � � � �� �
Please read these instructions carefully before installing the Swash 450 / 550.
Failure to do so could result in flooding, leaking, or damage to the product. CAUTION
1) Remove Toilet Seat
a) Lift hinge covers and use a screwdriver
to remove the mounting bolts.
b) Remove the toilet seat.
��
��
��
Steps may vary by type of seat.
2) Turn Water Off and Flush Toilet
You may wish to place a container under
�
the� tank� to� catch
any leaking that could
�
occur during
installation.
��
a) Turn water valve off completely.
b) Flush the toilet to empty the tank.
�
c) Disconnect water
supply line from toilet tank.
�
��
�
IMPORTANT: Do not continue without completing these
steps! Failure to do so could result in flooding, leaking, or
damage to the Swash 450 / 550.
�
�
��
3) Install Mounting Plate
NOTE: The following instructions are for standard Mounting
Hardware.
Refer to separate instructions for Alternate
Mounting Hardware.
��
� � � � � �� � �� � �� �
a) Place Mounting Plate over mounting holes,
flat side down, curve toward the back of toilet.
�
b) Insert bolts through the Mounting Plate and loosely tighten
the wingnuts. Make sure the crush washer is positioned
with the tapered end up (see graphic).
2
Installation (continued)
�
�
3) Install Mounting Plate (continued)
L
3c
c) Adjust mounting plate so length (L) between the front of the
toilet bowl and the back of the mounting plate is as follows:
Round (S450 / S550 - RW or RB):
L = 18 1/4” (465 mm)
Elongated (S450 / S550 - EW or EB):
L = 20 1/2” (495 mm)
d) Tighten Mounting Bolts with� screwdriver until the
mounting plate is securely fastened to the toilet.
4) Connect T-Valve and Hoses
If your water supply line is rigid, you may need to replace
it before continuing. See page 2 for further details.
��
a) Install the T-Valve between the water
supply line & the toilet tank.
b) Place the Swash 450 / 550 on or
beside the toilet and connect the
Bidet Hose to the Swash 450 / 550.
�
��
T � � � �� �
�
� �� � � �� � � �
�
IMPORTANT! Use wrench to tighten
all connections before continuing.
Failure to do so could result in flooding,
leaking, or damage to the Swash 450 / 550.
Water Supply Line
5) Attach the Swash 450 / 550
Slide the Swash 450 / 550 onto the
mounting plate.
You will hear a "click" indicating the
seat has been properly attached.
CLICK
Press to
Release
To release the Swash 450 / 550: push
the button located on the right hand
corner of the seat and gently pull.
CAUTION: Only use a
grounded GFI outlet!
6) Turn On Water and Connect Power
a) Turn the water valve back on slowly.
Ensure the connections are not
leaking before continuing.
b) Make sure hands are dry.
��
Insert the power plug into a grounded
GFI outlet. The blue power LED will illuminate.
3
��
Installation (continued)
7) Filling the Reservoir
Sit on the Swash 450 / 550 to activate the seat switch. Press one of the wash functions on the control.
The reservoir will begin to fill. It will take between 20 and 40 seconds for the reservoir to fill
completely.
When the reservoir is full, the wash wand will extend and begin to spray. Push STOP to cancel the
wash function.
Your Swash is now ready for use!
Troubleshooting
Issue
�
Possible Causes
Solution
Low water flow or
pressure
1) Clogged filter
2) Twisted hose
3) Household water pressure low
1) Clean filter
2) Straighten the hose
3) Increase water pressure to the Swash
2
Nozzles do not function
properly
1) Nozzles are dirty
2) Clogged filter
3) Water pressure is too low
1) Clean the nozzles
2) Clean the filters
3) Adjust water pressure
3
Nozzles fail to retract
Nozzles are dirty
4
Washing feature does
not work or fails to spray
1) User not properly seated
2) Seat Switch not contacting toilet
fixture correctly
5
Product shuts off
during use
1) Washing time exceeded 5 minutes
2) Power failure
1) Repeat Cleaning function
2) Check power and/or unplug the
cord to reset
6
Seat not heated
Seat temperature set to off
Reset heated seat temperature
7
Water not heated
Water temperature set to off
Reset heated water temperature
8
Water flow sporadic
or inconsistent
Pulsating / Spa mode activated
9
Dryer not working
(available in S550)
Dryer only operates when
activated by weight of person
1
�
Clean the nozzles
4
1) Adjust your sitting position
2) Make sure seat switch is contacting
toilet bowl (switch is in seat foot)
Reset to normal washing mode
Sit on product to operate Dryer
Operation
Some features of the Swash 450 / 550 are designed to function only when seat is occupied.
CONTROL PANEL
Swash 450
TM
water flow
2h
power
stop
back
4h
6h
front
8h
10h
powersave
seat temp
water temp
Swash 450
Flow / Timer
LED Indicators
Stop
(for Wash and Dryer)
Powersave
Function
Water Temperature
Low>Med>High>Off
Swash 550
TM
water flow
Power
LED Indicator
2h
power
Posterior (Rear)
Cleansing
stop
back
4h
6h
front
8h
powersave
Feminine (Front)
Cleansing
Water Pressure
Adjustment
10h
seat temp
water temp
warm air
Swash 550
Seat Temperature
Low>Med>High>Off
Warm Air Dryer
On
Low>Med>High
(available in S550)
Getting Started
Press FRONT or BACK button to fill the bidet tank.
Wait a few minutes to allow the seat & bidet water to warm.
View of
Side Control Panel
Using the Swash 450 / 550
water flow
Warm Water Washing:
Sit on the seat and press the FRONT or BACK button to begin
water flow. Press the STOP button to discontinue the water flow.
Water Flow/Pressure Adjustment:
While seated, you may adjust the water pressure by pressing the
FRONT or BACK button repeatedly until the desired pressure is
reached. There are five levels of water pressure.
Pulsating Water Mode: (water pressure level must be at 3 or above)
To change to pulsating mode, press and hold the FRONT or BACK button
for over 3 seconds. To deactivate and return to normal washing mode,
repeat the above step.
Warm Air Dryer (available in S550):
Press the WARM AIR button to start the dryer. Press STOP to stop the dryer.
5
stop
back
front
water flow
stop
back
front
water flow
stop
stop
back
front
warm air
Operation (continued)
Adjusting Seat, Water, and Dryer Temperature
Adjusting Seat Temperature
Press SEAT TEMP button to adjust temperature. Repeat until desired level is achieved.
There are four temperature levels: low>medium>high>off . No LED light up when
seat heating is off. Each LED display represents one level increase.
seat temp
Adjusting Water Temperature
Press WATER TEMP button to adjust temperature. Repeat until desired level is achieved.
There are four temperature levels: low>medium>high>off No LED light up when
water heating is off. Each LED light display represents one level increase.
seat temp
Adjusting Warm Air Dryer Temperature (available in S550)
While seated,press WARM AIR button to adjust temperature. Repeat until desired level
is achieved. There are three temperature levels: low>medium>high Each LED light
display represents one level increase.
warm air
NOTE: Temperature settings are stored in
memory according to last settings
Power Save Mode
You can turn off the seat and water warming features temporarily (between 2 - 10 hours)
by initiating Powersave in the Swash 450 / 550. For longer periods of non-use, unplug the
Swash 450/550 to conserve energy.
Setting Powersave Start and End Times
a) Press the POWERSAVE button on the remote control for over 3 seconds. This will
activate SETTING MODE and POWER LED will begin flashing.
b) While in SETTING MODE, press the POWERSAVE button through the cycle
(between 2 - 10 hours), each LED display light (located above the POWERSAVE
button) represents an increment of 2 hours of powersave.
c) Powersave mode will be engaged when buttons have not been pressed for 5
seconds. The POWER LED and FLOW / TIMER LED will flash continuously while
the Swash 450/550 is in Powersave status.
d) Powersave mode will cancel automatically, when the programmed Powersave
duration (between 2 - 10 hours) is completed.
2h
4h
6h
8h
10h
powersave
power
2h
4h
6h
8h
10h
powersave
power
When Powersave is Operating
a) Sitting on the Swash while it is in Powersave mode will not return the unit to normal
operation.
b) To return the Swash into normal operation, press either the STOP or POWERSAVE
button once.
or
stop
c) The Swash will not re-enter into Powersave until user proceeds to set the powersave
setting again.
6
powersave
Maintenance
� � � � �� �
Always unplug the Swash 450 / 550 before cleaning!
� � � � �� �
Seat� Cleaning and Removal
Use a soft, damp cloth and mild cleanser (such as dish
soap) to wipe down the seat. DO NOT scrub or use
harsh, abrasive products to clean the Swash 450 / 550.
For a more thorough cleaning, you may remove the
Swash 450 / 550. To release, push the button located
on the back right side of the seat and pull forward.
� �� � �
�
Nozzle
Cleaning
It is recommended that you clean the retractable nozzles monthly or as
necessary. To clean the nozzles, pull them out gently and use a soft, damp
brush or cloth to wipe down. DO NOT use soap or detergents to clean the nozzles.
Filter Cleaning
For proper Swash 450 / 550 function, it is important to occasionally clean the filters. Frequency of cleaning
depends on your local water supply. Clogged filters cause decreased water flow, affecting operation.
BIDET-HOSE FILTER:
T-VALVE FILTER:
1
2
� �� � �
3
4
1) Turn water valve off completely.
1
2) Flush the toilet to empty the water
tank. (Failure to do so could result
in leaking or flooding!)
2
� �� � �
3) Unscrew the filter from the T-Valve.
(the end not connected to a hose)
3
4
6
2) Flush the toilet to empty the water
tank. (Failure to do so could result
in leaking or flooding!)
3) Disconnect the Bidet Hose from
the Swash 450 / 550.
4) Gently brush and clean the filter
with water to remove build-up.
4) Gently brush and clean the filter
with water to remove build-up.
5
1) Turn water valve off completely.
5) Reconnect the filter to the T-Valve.
5
6
6) Turn the water valve back on.
5) Reconnect the Bidet Hose to the
Swash 450 / 550.
6) Turn the water valve back on.
For other issues or questions, contact Brondell Customer Service:
1-888-542-3355
� Information
Contact
Warranty
Brondell Inc.
PO Box 470085
San Francisco, CA 94147-0085
� Swash 450 / 550 is covered by a one year
The
warranty, valid from the original date of purchase.
Phone:
E-mail:
WEB:
Please complete & return the enclosed
registration card to receive important product
updates.
1-888-542-3355
support@brondell.com
www.brondell.com
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising