Product Manual - La Crosse Technology

Product Manual - La Crosse Technology
Model: 617-1392B/617-1392W
Instruction Manual
DC: 051616
+ Alarm 1
+ Alarm 2
Snooze Button
Page | 1
Get Started
1. Insert 2 new AAA Alkaline batteries (not included) into the
alarm clock. Observe the correct polarity.
Restart: If there is no indoor temperature data after 60
seconds, remove batteries from the alarm clock, press any
button 20 times. After 15 minutes, start again.
Set Time, Date, etc.
1. Hold the TIME SET button for 5 seconds, to enter time set
2. Press the ▲ or ▼ buttons to adjust values.
3. Press the TIME SET button to confirm adjustments and
move to the next item.
Setting Order:
1. RCC time signal (On/Off)
2. 12/24 hour time format
Note: 12-hour time = Month/Date display
24-hour time = Day/Month display
3. Time Zone - 4 time zones
4. Hour
5. Minutes
6. Year
7. Month
8. Date (day of the week sets automatically)
9. DST (Daylight Saving Time On/Off)
10. Fahrenheit/Celsius (°F or °C)
Press the TIME SET button to exit, or wait 15 seconds without
pressing buttons to return to the normal time display.
Date Display
The date may be displayed as the Month/Date format or as the
Date/Month format.
Page | 2
1. Press the ▲ button to select 12-hour time and the
Month/Date format.
2. Press the ▲ button again to select 24-hour time and the
Date/Month format.
Note: From the time display, press the TIME SET button to
select Month/Date or Year to display in the lower left-hand
Set Alarm 1 or Alarm 2
The clock has two separate time alarms. Setting the alarms and
activating the alarms are separate actions.
1. Hold the AL-SET button for 2 seconds to enter alarm time
set mode for Alarm 1.
2. Press the ▲ or ▼ buttons to adjust the alarm time. The
minutes and hours are set together.
3. Hold the ▲ or ▼ buttons to change quickly.
4. Press the AL-SET button to confirm and move to Alarm 2.
5. Press the ▲ or ▼ buttons to adjust the alarm time. The
minutes and hours are set together.
6. Hold the ▲ or ▼ buttons to change quickly.
7. Press the AL-SET button to confirm and exit.
Activate/Deactivate Alarm 1 and Alarm 2
To activate or deactivate Alarm 1 or Alarm 2, use the slide
bars on the back of the clock.
There is a slide bar (ON/OFF) for AL 1 and for AL 2.
When active, Alarm 1 will show in the Date display with
alarm icon.
When active, Alarm 2 will show in the Temperature display
with alarm icon.
When alarm sounds, press the SNOOZE/LIGHT
button to silence the alarm for 5 minutes.
The alarm icon will flash.
Page | 3
Snooze may be repeated up to 7 times.
In snooze mode, press any button except SNOOZE/LIGHT to
stop alarm for one day.
Note: The alarm is crescendo sound. The alarm will sound for 2
minutes and then shut off completely if no buttons are pressed.
Press the SNOOZE/LIGHT button to
activate the backlight for 15 seconds.
Atomic Time Signal Search
Hold the ▼ button to start or stop a WWVB signal search.
WWVB Icon will flash when searching.
For information about WWVB visit:
Tip: When batteries are inserted, the alarm clock will start
searching. If there is no WWVB reception, the alarm clock will
search the WWVB time signal every hour until the WWVB time
is received. After reception, this alarm clock will automatically
search for the atomic signal daily at 2:00am.
Reset Button
If the display of the alarm clock is distorted or the alarm
clock is not functioning properly, check that batteries are
fresh and press the RESET button one time.
The alarm clock will fully populate then return to default
Position Alarm Clock
Position the alarm clock six feet from other electronics for
best WWVB reception.
Have the front or back of the alarm clock facing Colorado.
Care and Maintenance
Do not mix old and new batteries
Do not mix Alkaline, Standard, Lithium, or Rechargeable Batteries
Always purchase the correct size and grade of battery suitable for
the intended use.
Replace all batteries of a set at the same time.
Page | 4
Clean the battery contacts and also those of the device prior to
battery installation.
Ensure the batteries are installed correctly in regard to polarity (+/-).
Remove batteries from equipment when it is not to be used for an
extended period.
Promptly remove expired batteries.
Temperature Range: 14.1°F to 122°F (-9.9°C to 50°C)
2-AAA, IEC, LR3 batteries (not included)
Battery Life:
Battery Life:
Battery life is over 12 months
Alarm Clock:
3.65” T x 2.85” W x 1.75” D inches
(92.71 x 72.39 x 44.45 mm)
Warranty and Support
La Crosse Technology, Ltd. provides a 1-year limited time warranty
(from date of purchase) on this product relating to manufacturing
defects in materials & workmanship.
Before returning a product, please contact our friendly
customer support with questions or visit our online help
(manuals and FAQS):
Phone: 1-608-782-1610
Online Product Support:
Product Registration:
View full warranty details online at:
Warranty Address:
La Crosse Technology, Ltd
2830 S. 26th St.
La Crosse, WI 54601
Page | 5
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device must not be co-located or operating in conjunction with any other
antenna or transmitter.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user authority to operate the equipment.
All rights reserved. This manual may not be reproduced in any form, even in part,
or duplicated or processed using electronic, mechanical or chemical process
without the written permission of the publisher. This booklet may contain errors or
misprints. The information it contains is regularly checked and corrections are
included in subsequent editions. We disclaim any responsibility for any technical
error or printing error, or their consequences.
All trademarks and patents are recognized.
Page | 6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF