SIM557/Drill Pump - Law Supply, Inc.

SIM557/Drill Pump - Law Supply, Inc.
OWNER’S MANUAL
Drill Pump and Hose Kit
293 Wright St., Delavan, WI 53115
Phone: 1-800-468-7867
1-800-546-7867
Fax:
1-800-390-5351
3680 0400
MOD. CM10-01, CMK-02
Installation/Operation/Parts
For further operating, installation,
or maintenance assistance:
Call 1-800-468-7867
English . . . . . . . . . . . . . . Pages 2-3
©2004 PRINTED IN U.S.A.
SIM557 (Rev. 9/2/04)
Safety / Installation
READ AND FOLLOW
SAFETY INSTRUCTIONS!
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for
one of the following signal words and be alert to the
potential for personal injury.
warns about hazards that will cause serious
personal injury, death or major property damage if
ignored.
warns about hazards that can cause serious
personal injury, death or major property damage if
ignored.
warns about hazards that will or can cause
minor personal injury or property damage if ignored.
The label NOTICE indicates special instructions which
are important but not related to hazards.
Carefully read and follow all safety instructions in this
manual and on pump.
Keep safety labels in good condition.
Replace missing or damaged safety labels.
2
2. Disconnect electric drill power before servicing pump
components.
3. Check hoses for weak or worn condition before each
use. Make sure all connections are secure.
4. Provide a means of pressure relief for pumps whose
discharge line can be shut off or obstructed.
Hazardous voltage. Can shock, burn or
cause death. Use only with a 3-wire grounded cord or
with a double insulated drill and follow safety precautions recommended by the electric drill manufacturer. To
reduce risk of electric shock, keep hands, feet and drill
dry. Unplug the drill at once if it gets wet. Do not handle
the drill or the drill motor with wet hands or when standing on a wet or a damp surface, or in water.
INSTALLATION
(See Figure 1)
1. Attach the white inlet adapter and suction tubing and
the clear outlet garden hose. Use good hose washers.
The pump outlet is clearly marked.
Drill
Chuck
Clear
Outlet
Hose
DESCRIPTION
This Drill Pump is designed to handle many kinds of
small pumping jobs, such as filling and emptying aquariums, crocks, sinks, tubs, window wells, stopped up
plumbing, and emptying crank cases. The drill pump
may also be used with fresh or salt water and water like
liquids including non-flammable lube oils.
Waste
Container
Pump
Outlet
Pump
Inlet
Suction
Tube
Adapter
Tubing
SPECIFICATIONS
Use a 1/4” drill that is grounded or double insulated.
Use at temperatures below 120° F.
Figure 1 – Attach the inlet hoses, the outlet hose
and the drill chuck as shown.
Uses regular garden hose fittings.
NOTICE: Pumping sand, small rocks, or running the
pump dry can ruin the pump.
PERFORMANCE
The unit can pump up to 6 G.P.M. of water at low
heads. Lifts water 15 to 20 feet after priming. This is a
light duty pump with a normal life of about 50 hours of
pumping.
GENERAL SAFETY
For more information, see your retailer or call Simer customer service at 1-800-468-7867.
NOTICE: The suction tubing should be as short as
possible, kink free, and non-collapsible.
2. Tighten the drill chuck onto the pump shaft.
3. Squirt a little oil or water into the pump inlet port
and, with the drill chuck, turn the pump a turn or two
to coat the inside of the pump with liquid.
4. Place the suction tubing in the water to be pumped.
5. Plug in the drill.
6. Hold the drill in one hand and the suction tubing in
the other.
1. Know the pump application, limitations, and potential hazards.
Risk of fire or explosion. Do not use in
explosive atmospheres. Failure to follow this warning
can result in personal injury and/or property damage.
For parts or assistance, call Simer Customer Service at 1-800-468-7867
/ 1-800-546-7867
Operation / Troubleshooting
3
OPERATION
8. Insert the opposite end of the discharge hose in the
waste oil container.
Hazardous voltage. Can shock, burn or
cause death. Do not touch the drill motor, water, or discharge piping when pump is connected to electrical
power. Before attempting to service, always disconnect
the electric drill from the power source.
9. Tighten the drill chuck onto the pump shaft.
10. Hold the pump in one hand and the drill in the
other hand and start the drill.
11. When the oil stops coming out stop the drill.
1. Be sure the suction tube is air tight.
2. Be sure the drill is turning in the right direction.
This end
to a waste
oil container.
NOTICE: When running backward the suction and
outlet are reversed.
3. Make sure the suction tube is not flattened or kinked.
Pump
Outlet
4. Be sure the discharge hose is open and not kinked.
5. Continue pumping until you are finished.
AUTOMOTIVE ENGINE OIL CHANGE
KIT (CMK-02) INSTRUCTIONS
1. Screw
the Clear
Plastic
Discharge
Hose onto
the Pump Outlet
Pump
Inlet
2. Insert the
3" x 3/8"OD
Adapter Tubing
into the Pump Inlet
(See Figure 2)
1. Read and follow the original instructions on Page 2.
2. The engine oil must be warm. Run the engine 5
minutes to warm up the oil, then shut it off before
changing the oil.
3. Insert the
3' x .25" OD
White Plastic
Suction Hose
through the
Adapter Tube
and into the
pump inlet.
3. Insert the 3/8” x 3” long white adapter tube firmly
into the inlet of the chuckmaster pump.
4. Insert the .25” x 3’ long white suction tube through
the adapter tube and firmly into the pump inlet.
This end
to the
engine
dipstick
hole.
5. Connect the clear plastic discharge hose to the
pump outlet.
6. Remove the dipstick from the engine.
7. Insert the opposite end of the suction tube into the
dipstick hole until it touches the bottom of the oil
pan.
Figure 2 – Insert the suction tube into the inlet
port.
TROUBLESHOOTING
SYMPTOM
Pump fails to prime
CORRECTIVE ACTION
Remove any kinks in the tubing.
Check washer in hose fitting. Replace hose if necessary.
Restricted inlet or discharge.
Air leak at inlet.
Flow rate is too low.
Drill is running too slow.
Restricted inlet or discharge.
For parts or assistance, call Simer Customer Service at 1-800-468-7867
/ 1-800-546-7867
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising