Masters Series ½ to 5 HP Specifications

Masters Series ½ to 5 HP Specifications
SPECIFICATIONS
MASTERS SERIES® FLOATING FOUNTAIN AERATOR SYSTEM
1.0
1.1
1.2
GENERAL
DESCRIPTION
A.
Manufacturer shall furnish a floating fountain aerator system capable of pumping
water from below the surface of a body of water.
B.
A submersible motor shall draw water into an impeller housing where it shall be
pumped into the atmosphere in the form of a decorative spray - type fountain.
C.
The water droplets shall become oxygen enriched and return to the surface, therefore
transferring oxygen from the atmosphere into the body of water. Surface area of water
body shall also be increased through constant wave action resulting in additional
atmospheric oxygen transfer.
D.
This repeated action shall effectively mix and de-stratify the body of water and
distribute the dissolved oxygen continuously.
E.
Fountain aerator system shall include an oil-cooled motor sealed in a stainless steel
housing, with shaft mounted impeller, attached to a float. This assembly shall be
connected to an electrical control panel by underwater power cable, all of which as
specified in SECTION 1.2.
AERATOR COMPONENTS DESCRIPTION
A.
1 – 5HP Float shall be made of linear low density polyethylene. Float shall contain a
center tube which shall be minimum Schedule 40 PVC and is attached to the impeller
housing with four series 300 stainless steel hex head bolts. An o-ring is used to
prevent leakage. A protective series 300 stainless steel intake screen shall be mounted
around the impeller housing between the float assembly and motor housing. The
motor housing shall be attached to the impeller housing with series 300 stainless steel
hardware. All optional lights and anchor mounting shall be capable of being installed
into fixture mounting areas which are molded into the float design as an integral part
of the float. (See SECTION 5).
B.
Impeller shall be precision machined and balanced, formed using Series 300 Stainless
Steel or molded composite. The impeller is connected to the motor shaft by a series
300 stainless steel bolt and lockwasher.
C.
Impeller Housing shall be molded from glass reinforced nylon type 6 material. The
impeller housing shall be precision molded to accept the float tube and capable of
being bolted to the motor housing. The impeller housing shall house the impeller,
insert and flow straightener (if applicable).
D.
Flow Straightener (where applicable) shall be precision machined from acetal
material and shall have 20 curved vanes. The vanes shall take the spinning discharge
water from the impeller and convert it to a straight, vertical flow. The gap between
the vanes shall be at least 3/8” wide and have a total length not less than 2-1/2” long.
It shall be factory installed for various optional spray patterns.
Page 1
03/16
E.
Motor Housing shall be Series 300 Stainless Steel. The housing shall have a
permanent Series 300 stainless steel electrical hub welded on the side of the housing
to allow electrical cable entry..
F.
Motor shall contain a Series 316 Stainless Steel shaft incorporating a permanent split
phase capacitor run on single phase motors and a polyphase induction on three phase
motors. The rotor shall be dynamically balanced and run in a ball bearing supported
system. The stator windings shall be double dipped and baked with a Class F
insulation, designed for oil immersion operation. The oil shall be a highly refined,
mineral oil of food grade quality, specially formulated for lubrication. It shall meet
FDA regulations. The oil shall provide continuous lubrication of bearings and internal
seals and further function as an efficient heat transfer medium, allowing the motor to
operate at 3450 RPM, at relatively low temperatures. The motor shall be contained in
the motor housing by a series 300 stainless steel top plate.
G.
Seals used to protect the motor against water or oil leakage shall be a mechanical,
rotating type assembly, composed of silicon carbide and series 300 stainless steel. All
elastomers shall meet UL 778 requirements. This assembly shall then be encapsulated
and protected within a series 300 stainless steel cartridge assembly.
H.
Underwater Power Cable shall be UL Listed and specifically designed for
underwater use. The conductors are flexible, stranded copper wire sized for the amp
draw and length of run. The conductors shall be resistant to oil, water and cracking.
Power cable shall be fitted with a cable strain relief device, located within five feet of
motor housing, capable of being attached to the latch mounted on the motor housing
clamp. This will ensure that no potential damage can occur to any cable connections,
due to tension on the cable.
I.
Underwater Power Cable Disconnect shall be located approximately three feet from
the motor housing. It is a two piece molded assembly made of thermoplastics,
meeting UL 778 requirements. The cap end shall be permanently connected to the
underwater pin and socket connector
(see Section 1.2 Item J.). The body end of
the disconnect shall be permanently attached to the underwater power cable and
sealed with an approved compound. This is intended to prevent water entry if damage
should occur to the cable. The disconnect shall be sealed with an internal o-ring and
by an external series 300 stainless steel clamp ring, which can be easily opened.
J.
Underwater Pin and Socket Connector shall consist of a Series 900 IP68 pin and
socket connector. It shall be of a 4 pin configuration rated 32 amps at 600 volts AC.
The pin end shall be potted into a series 300 stainless steel 90° adapter elbow with an
approved ridged epoxy. This assembly shall be permanently attached to the series 300
stainless steel hub that is welded onto the side of the series 300 stainless steel motor
housing. The socket end shall be attached to a 36” piece of UL Listed underwater
power cable. It shall be permanently secured to the UL Listed power cable by means
of an integrated clamp and series 300 stainless steel screws. It shall be completely
epoxied to prevent entry of water or any other foreign matter. The other end of this
assembly is permanently attached to the cap end of the underwater cable disconnect.
It is sealed with a flexible potting compound.
K.
Fasteners and Anchor Connectors shall be Series 300 Stainless Steel.
L.
Electrical Control Panel specifications, see SECTION 3.
Page 2
03/16
M.
Intake Screen shall be made of 20 Gauge, Series 300 Stainless Steel. The screen shall
have a minimum of 58% open area, representing 91 square inches of open intake area.
N.
Large Custom Intake Screen (optional) shall be made of 18 Gauge, Series 300
Stainless Steel. The large custom intake screen shall completely enclose the motor
power unit assembly. It shall have a minimum of 58% open area representing 765
square inches of open intake area. Additional depth is required.
O.
Nozzles (optional) shall be interchangeable without the use of tools, in most cases.
Nozzles will be sealed to the float tube utilizing an o-ring and series 300 stainless
steel thumb screws to prevent leakage.
P.
Series 316 Stainless Steel Upgrade (optional) is available for sites with salt or
brackish water. This option will upgrade all series 300 stainless steel components to
series 316.
Q.
Horizontal MASTERS SERIES® (optional) is designed for fountain aerators in
shallow applications. Requires a minimum operating depth of 16 inches and the use
of a straightened flow pattern. Includes a large custom intake screen and supplemental
float.
Page 3
03/16
FOUNTAIN AERATOR DETAIL SPECIFICATIONS
2.0
DETAILED INFORMATION – Refer to TABLES 1, 2 and 3 to complete this section
2.1
This specification is intended to provide prospective bidders the necessary information
pertaining
to
the
fountain
aerator(s)
specified
for
the
____________________________________ Project.
2.2
The MOTOR(S) shall be _____ HP, operating at ________ Volts, 60 Hertz, _____ Phase at
3450 RPM.
2.3
The MASTERS SERIES MODEL(S) specified shall be the _____________________
MODEL
NUMBER
_____________
capable
of
creating
a
_____________________________ pattern. It shall come complete with an electrical control
panel, protective intake screen to be attached to a float assembly and ________ feet of
________ gauge, 4 conductor underwater power cable.
2.4
The fountain aerator shall produce a SPRAY PATTERN ______ feet in diameter and ______
feet in height.
Page 4
03/16
FOUNTAIN AERATOR DETAIL SPECIFICATIONS (cont.)
3.0
ELECTRICAL CONTROL PANEL COMPONENTS DESCRIPTION
A.
Electrical Enclosure shall be NEMA 3R type, galvanized and powder-coat painted
gray in color. Panel shall be both lock and mount capable.
B.
Ground Fault Protection
1. Single phase applications, a GFCI breaker shall provide overload and short circuit
protection, combined with Class A ground fault protection.
2. Three phase applications, a molded case breaker shall provide overload and short
circuit protection, while a residual current device rated at 30 mA shall provide
ground fault protection.
C.
Control Breaker shall provide overload protection and be capable of disconnecting
all incoming electricity from the control panel.
D.
Motor Contactor shall provide a means for disconnection of all motor leads. It shall
be a magnetic, across the line starter type.
E.
Overload Relay shall provide overload protection by means of a bi-metallic overload
relay. It is adjustable over the full load amperage draw of the motor. It shall have a
visual trip indicator, test button and manual/automatic reset modes.
F.
Digital Timer shall be a single pole type, rated at 120 Volts, 16 Amps, capable of 8
ON / OFF functions per day for 7 days. Digital timer has a lithium battery to retain the
programming when power is disconnected.
3.1
SAFETY TESTING CONTROL PANEL
The electrical control panel shall be tested and approved as a complete unit. It is inspected
and listed by Underwriters Laboratories, Inc. under Category 508: Industrial Control Panels
and Category 778: Submersible Aerators and Aerating Fountain Pump Systems.
3.2
ACCEPTABLE MANUFACTURER
This fountain aerator electrical control panel, as specified in Section 3.0, shall be
manufactured by AQUAMASTER® FOUNTAINS AND AERATORS, 16024 CTH X, Kiel,
WI 53042, (800) 693-3144 or approved equal.
3.3
INSTALLATION
The electrical control panel must be installed in accordance with the installation instructions,
in compliance with all local and National Electrical Code requirements. This should be done
by a licensed electrical contractor. Any alterations to or substitution for items in this system,
unless allowed by the installation instructions, will void the Underwriters Laboratories
Listing and will void the product warranty. It may also create a hazardous installation. Read
the instructions thoroughly before starting the installation and follow them carefully
throughout.
3.4
ELECTRICAL CONTROL PANEL WARRANTY
All control panels and their components have a 3 year warranty on parts and labor.
Page 5
03/16
FOUNTAIN AERATOR DETAIL SPEFICATIONS (cont.)
4.0
SAFETY TESTING
The floating fountain aeration system shall be tested and approved as a complete unit. This
approval must meet Underwriters Laboratories Inc. requirements in compliance with
Category 508: Industrial Control Panels and Category 778: Submersible Aerators and
Aerating Fountain Pump Systems. Individual component testing and wet niche environment
equipment approval are not acceptable.
4.1
ACCEPTABLE MANUFACTURER
This fountain aerator, as specified in Sections 2.2, 2.3 and 2.4, shall be manufactured by
AQUAMASTER® FOUNTAINS AND AERATORS, 16024 CTH X, Kiel, WI 53042, (800)
693-3144, or approved equal.
4.2
INSTALLATION
All AQUAMASTER® FOUNTAIN AERATORS are designed and built to be installed with
an AQUAMASTER® UL Listed control panel and to be operated as a complete system. Any
alterations to or substitution for items in this system, unless allowed by the installation
instructions, will void the UL Listing and will void the product warranty. It may also create a
hazardous installation. Read the instructions thoroughly before starting the installation and
follow them carefully throughout.
4.3
WARRANTY
All 1 – 5HP AQUAMASTER® THE MASTERS SERIES FOUNTAIN AERATORS motor,
seal assembly, float and underwater power cable (referred to as in-water components) are
covered under warranty at 100% replacement cost should it fail due to defects in materials or
workmanship for a period of 5 years on parts and labor. This is in effect from the date of
shipment, when given normal and proper usage as determined by The Seller upon
examination, and when owned by the original user.
Page 6
03/16
FOUNTAIN AERATOR LIGHTING SYSTEMS AND OPTIONS SPECIFICATIONS
5.0
LIGHTING SYSTEM shall be LED/RGBW ________ Volts/Watts, Model
#(s)_________________.
There
are
______
total
fixtures,
containing
________________________ (choose color(s): white, amber, blue, red, or green) color board
assemblies.
5.1
A total length of __________ feet of _______ gauge 3(LED) or 5(RGBW) conductor
underwater power cable is required. Two runs of cable may be required; reference cable
sizing chart.
5.2
MULTI-PURPOSE ELECTRONIC LIGHT SYSTEM SEQUENCER shall be capable of
cycling light fixtures off and on, up to 6 programs. Yes____No____
5.3
A total length of __________ feet of _______ gauge 4 conductor underwater power cable is
required for sequencer. Two runs of cable are required.
5.4
DEEP WATER INTAKE SYSTEM shall be capable of drawing water from further depths,
in three foot increments. This system provides the fountain aerator the capability to destratify the pond very efficiently. Total length should reach beyond 50% depth but not to
exceed 75%. Total ________ feet.
5.5
LARGE CUSTOM INTAKE SCREEN shall provide additional protected intake area if
Fountain Aerator(s) will operate in a potentially high debris filled aquatic environment. Yes
____ No _____
5.6
SERIES 316 STAINLESS STEEL UPGRADE is available for sites with salt or brackish
water. Yes ____ No _____
5.7
HORIZONTAL MASTERS SERIES® is designed for 1-5HP fountain aerators in shallow
applications. Yes ____ No _____
Please refer to TABLE 4 to assist in the completion of SECTION 5.
Page 7
03/16
6.0
DESCRIPTION - LIGHTING
A. Light Set shall consist of line voltage (120 VAC) 11W LED, 22W LED, 35W LED, or
40W RGBW LED lighting system with either 2, 3, 4, 6, or 8 lights.
B. Lights shall consist of a power supply/driver module with a 11W, 22W, 35W, or 40W
RGBW (10W red, 10W green, 10W blue, 10W white) LED light engine.
C. Light Fixture shall be of Series 300 Stainless Steel construction. They shall have a
permanent series 300 stainless steel electrical hub welded on the bottom of the housing to
allow electrical cable entry and be mounted with series 300 stainless steel brackets and
fasteners.
D. Light Fixture Assembly shall consist of a lens made of tempered glass with a clear nondiffusing surface with a minimum of 5/32nd thickness and sealed with “V” shaped lens
gasket made of silicon. Clamp ring shall be of series 300 stainless steel. Fasteners and
mounting hardware shall be of series 300 stainless steel.
E. Underwater Pin and Socket Connector shall consist of a Series 900, IP68 pin and
socket connector. It shall be of a 3(LED) or 5(RGBW) pin configuration rated 32 Amps
at 600 VAC. The pin and socket ends shall each be attached to a UL Listed underwater
power cable rated at 600 Volts. They both shall be permanently secured to their UL
Listed power cables by an integrated neoprene grommet and compression nut assembly.
These assemblies shall be epoxy filled to prevent entry of water or any other foreign
matter. The pin end assembly shall be permanently attached to the light fixture with a
nonmetallic connector and potted using a flexible approved potting compound. The
socket end assembly shall be permanently attached to the power cable. Both the pin end
and socket end assemblies come with protector caps.
F. Underwater Power Cable shall be UL Listed and specifically designed for underwater
use. The conductors are flexible, stranded copper wire sized for the amp draw and length
of run. The conductors shall be resistant to oil, water and cracking. Power cable shall be
fitted with a cable strain relief device, located within five feet of the first light fixture.
This will ensure that no potential damage can occur to any cable connections, due to
tension on the cable.
G. Light Controls shall consist of a GFCI (Ground Fault Circuit Interrupter), overcurrent
protection (fuse), digital timer with battery back-up. The Sequencer (optional) shall be
capable of cycling light fixtures on and off, up to 8 fixtures. The RGBW controller
(optional) is pre-programmed with assorted color, shows and holiday themed selectable
programs. The controller can also adjust program speed and brightness. The standard
controller shall consist of a programmable controller with push button interface. An
optional programmable WiFi controller is available with an Android or iOS app included.
An Android tablet preloaded with the app and connected to the controller is also available
as a WiFi option.
H. Safety Testing shall be tested and approved as a complete assembly. This approval must
meet Underwriters Laboratories Inc. requirements in compliance with UL category 676:
Underwater Luminaires.
I. Warranty on all AQUAMASTER LIGHTING SYSTEMS are covered under warranty at
100% replacement cost should it fail due to defects in materials or workmanship for a
period of 3 years.
Page 8
03/16
TABLE 1: THE MASTERS SERIES® PERFORMANCE SPECIFICATIONS
TECHNICAL DATA
REFERENCE MATERIAL FOR SECTION 2.0 DETAILED INFORMATION
Voltage
and
Phase
Running Amp
Draw
M5410-SC
120 - 1PH
19.0
M5412-SC
208-240 - 1PH
9.6
208-240 - 3PH
5.4
440-480 - 3PH
2.7
Model
Number
M5412-3SC
HP
1
M5414-3SC
M5422-SC
M5422-3SC
208-240 - 1PH
12.6
2
208-240 - 3PH
6.3
440-480 - 3PH
3.1
3.5
208-240 - 1PH
15.2
208-240 - 3PH
10.1
M5424-3SC
M5432-SC
M5432-3SC
3
M5434-3SC
440-480 - 3PH
5.1
M5452-SC
208-240 - 1PH
27.1
208-240 - 3PH
18.0
440-480 - 3PH
9.0
Voltage
and
Phase
Running Amp
Draw
M5410-SC
120 - 1PH
19.0
M5412-SC
208-240 - 1PH
9.6
208-240 - 3PH
5.4
M5452-3SC
5
M5454-3SC
Model
Number
HP
1
M5412-3SC
440-480 - 3PH
2.7
M5422-SC
208-240 - 1PH
12.6
208-240 - 3PH
6.3
440-480 - 3PH
3.1
208-240 - 1PH
15.2
208-240 - 3PH
10.1
440-480 - 3PH
5.1
208-240 - 1PH
27.1
208-240 - 3PH
18.0
440-480 - 3PH
9.0
2
M5424-3SC
M5432-SC
3.5
M5432-3SC
3
M5434-3SC
M5452-SC
M5452-3SC
M5454-3SC
5
Minimum
Operating Depth
Ship Weight LBS.
3'
250
7 x 18
GPM 318
Upper 4 x 10
Lower 3 x 22
GPM 305
3'
250
10 x 24
GPM 344
Upper 6 x 11
Lower 4 x 26
GPM 345
3'
250
11 x 30
GPM 415
Upper 8 x 12
Lower 5 x 32
GPM 412
3'
300
15 x 36
GPM 535
Upper 10 x 12
Lower 6 x 35
GPM 532
Ace
MASTERS NOZZLE SERIES
M5414-3SC
M5422-3SC
LAKEWOOD
FULL FLOW
(no nozzle)
MASTERS NOZZLE
SERIES
Birdie
Biscayne
Crown & Geyser
Crystal Geyser
3x5
GPM 336
Upper 11
Lower 7 x 14
GPM 204
Geyser Ht 13
Crown 5 x 35
GPM 215
15 x 26
GPM 214
3.5 x 5
GPM 361
Upper 14
Lower 10 x 19
GPM 217
Geyser Ht 15
Crown 6 x 40
GPM 282
17 x 30
GPM 241
Geyser Ht 20
Crown 6 x 42
GPM 297
19 x 30
GPM 254
Geyser Ht 22
Crown 7 x 50
GPM 465
22 x 32
GPM 396
4.5 x 8
GPM 454
5 x 12
GPM 546
Upper 16
Lower 10 x 20
GPM 250
Upper 20
Lower 14 x 28
GPM 403
Page 9
03/16
TABLE 1: THE MASTERS SERIES® PERFORMANCE SPECIFICATIONS (cont.)
TECHNICAL DATA
REFERENCE MATERIAL FOR SECTION 2.0 DETAILED INFORMATION
Model
Number
HP
M5410-SC
M5412-SC
MASTERS NOZZLE SERIES
Voltage
and
Phase
Running Amp
Draw
120 - 1PH
19.0
208-240 - 1PH
9.6
208-240 - 3PH
5.4
1
M5412-3SC
M5414-3SC
440-480 - 3PH
2.7
M5422-SC
208-240 - 1PH
12.6
2
208-240 - 3PH
6.3
440-480 - 3PH
3.1
3.5
208-240 - 1PH
15.2
208-240 - 3PH
10.1
440-480 - 3PH
5.1
208-240 - 1PH
27.1
208-240 - 3PH
18.0
440-480 - 3PH
9.0
Voltage
And
Phase
Running
Amp Draw
120 - 1PH
19.0
208-240 - 1PH
9.6
M5412-3SC
208-240 - 3PH
5.4
M5414-3SC
440-480 - 3PH
2.7
208-240 - 1PH
12.6
208-240 - 3PH
6.3
440-480 - 3PH
3.1
208-240 - 1PH
15.2
208-240 - 3PH
10.1
M5422-3SC
M5424-3SC
M5432-SC
M5432-3SC
3
M5434-3SC
M5452-SC
M5452-3SC
5
M5454-3SC
Model
Number
HP
M5410-SC
M5412-SC
M5422-SC
2
M5424-3SC
M5432-SC
3.5
M5432-3SC
3
M5434-3SC
440-480 - 3PH
5.1
M5452-SC
208-240 - 1PH
27.1
208-240 - 3PH
18.0
440-480 - 3PH
9.0
M5452-3SC
M5454-3SC
5
Geyser
Par
Wide Geyser
11 x 8
GPM 119
18 x 2
GPM 141
Upper 6
Lower 3 x 20
GPM 274
18 x 10
GPM 182
15 x 9
GPM 136
20 x 2
GPM 205
Upper 10
Lower 4 x 26
GPM 294
22 x 10
GPM 203
17 x 11
GPM 143
24 x 2
GPM 209
Upper 13
Lower 6 x 30
GPM 377
26 x 10
GPM 208
20 x 12
GPM 308
28 x 2
GPM 380
Upper 15
Lower 7 x 40
GPM 487
28 x 10
GPM 345
NOZZLES REQUIRING FLOW STRAIGHTENERS
1
M5422-3SC
Eagle
Arabella
Augusta
Bayside
Baytree
Upper 7 x 12
Lower 3 x 28
GPM 268
9 x 20
GPM 236
Upper 9 x 11
Lower 3 x 18
GPM 197
N/A
Upper 9 x 15
Lower 5 x 35
GPM 308
12 x 28
GPM 243
Upper 11 x 14
Lower 3 x 22
GPM 209
N/A
Upper 11 x 16
Lower 5 x 38
GPM 337
13 x 30
GPM 269
Upper 13 x 16
Lower 3 x 24
GPM 239
N/A
Upper 13 x 18
Lower 5 x 55
GPM 482
15.5 x 35
GPM 452
Upper 16 x 20
Lower 4 x 30
GPM 390
Upper 23
Middle 17 x 17
Lower 12 x 29
GPM 279
Page 10
03/16
TABLE 1: THE MASTERS SERIES® PERFORMANCE SPECIFICATIONS (cont.)
TECHNICAL DATA
REFERENCE MATERIAL FOR SECTION 2.0 DETAILED INFORMATION
NOZZLES REQUIRING FLOW STRAIGHTENERS
Voltage
And
Phase
Running
Amp Draw
M5410-SC
120 - 1PH
19.0
M5412-SC
208-240 - 1PH
9.6
M5412-3SC
208-240 - 3PH
5.4
M5414-3SC
440-480 - 3PH
2.7
208-240 - 1PH
12.6
208-240 - 3PH
6.3
Model
Number
HP
1
M5422-SC
M5422-3SC
2
M5424-3SC
440-480 - 3PH
3.1
208-240 - 1PH
15.2
208-240 - 3PH
10.1
440-480 - 3PH
5.1
208-240 - 1PH
27.1
208-240 - 3PH
18.0
440-480 - 3PH
9.0
Voltage
and
Phase
Running Amp
Draw
M5410-SC
120 - 1PH
19.0
M5412-SC
208-240 - 1PH
9.6
M5412-3SC
208-240 - 3PH
5.4
M5414-3SC
440-480 - 3PH
2.7
208-240 - 1PH
12.6
208-240 - 3PH
6.3
440-480 - 3PH
3.1
M5432-SC
3.5
M5432-3SC
3
M5434-3SC
M5452-SC
M5452-3SC
5
M5454-3SC
Model
Number
HP
M5422-SC
2
M5424-3SC
M5432-SC
3.5
M5432-3SC
208-240 - 1PH
15.2
208-240 - 3PH
10.1
3
M5434-3SC
440-480 - 3PH
5.1
M5452-SC
208-240 - 1PH
27.1
208-240 - 3PH
18.0
440-480 - 3PH
9.0
M5452-3SC
M5454-3SC
5
Colonial
Diamondback
Doral
7 x 20
GPM 157
Upper 14
Lower 10 x 26
GPM 99
5 x 50
GPM 184
Upper 8 x 10
Lower 4 x 8
GPM 196
9 x 24
GPM 168
Upper 19
Lower 13 x 32
GPM 120
5 x 55
GPM 181
Upper 10 x 12
Lower 5 x 10
GPM 214
10 x 30
GPM 195
Upper 20
Lower 14 x 35
GPM 112
5 x 60
GPM 226
Upper 11 x 14
Lower 5 x 12
GPM 221
15 x 37
GPM 414
Upper 30
Lower 22 x 60
GPM 244
5 x 65
GPM 398
Upper 13 x 18
Lower 7 x 13
GPM 439
NOZZLES REQUIRING FLOW STRAIGHTENERS
1
M5422-3SC
Champion
Double Eagle
Firestone
Half Moon
Imperial
18 x 5
GPM 109
Upper 11
Middle 6 x 11
Lower 2 x 14
GPM 181
7 x 28
GPM 253
Upper 9
Middle 6 x 16
Lower 1 x 25
GPM 195
23 x 5
GPM 137
Upper 13
Middle 7 x 12
Lower 3 x 14
GPM 205
9 x 30
GPM 278
Upper 11
Middle 6.5 x 18
Lower 1.5 x 28
GPM 217
25 x 5
GPM 129
Upper 15
Middle 9 x 20
Lower 3 x 23
GPM 251
12 x 34
GPM 315
Upper 13
Middle 7 x 23
Lower 2.5 x 28
GPM 230
35 x 5
GPM 297
Upper 18
Middle 11 x 26
Lower 4 x 28
GPM 399
13 x 36
GPM 466
Upper 15
Middle 13 x 30
Lower 5 x 36
GPM 421
Page 11
03/16
TABLE 1: THE MASTERS SERIES® PERFORMANCE SPECIFICATIONS (cont.)
TECHNICAL DATA
REFERENCE MATERIAL FOR SECTION 2.0 DETAILED INFORMATION
NOZZLES REQUIRING FLOW STRAIGHTENERS
Voltage
and
Phase
Running Amp
Draw
120 - 1PH
19.0
208-240 - 1PH
9.6
M5412-3SC
208-240 - 3PH
5.4
M5414-3SC
440-480 - 3PH
2.7
M5422-SC
208-240 - 1PH
12.6
Model
Number
HP
M5410-SC
M5412-SC
M5422-3SC
1
2
M5424-3SC
208-240 - 3PH
6.3
440-480 - 3PH
3.1
208-240 - 1PH
15.2
208-240 - 3PH
10.1
440-480 - 3PH
5.1
208-240 - 1PH
27.1
208-240 - 3PH
18.0
440-480 - 3PH
9.0
Voltage
and
Phase
Running Amp
Draw
M5410-SC
120 - 1PH
19.0
M5412-SC
208-240 - 1PH
9.6
208-240 - 3PH
5.4
M5432-SC
3.5
M5432-3SC
3
M5434-3SC
M5452-SC
M5452-3SC
5
M5454-3SC
Model
Number
HP
1
M5412-3SC
440-480 - 3PH
2.7
M5422-SC
208-240 - 1PH
12.6
208-240 - 3PH
6.3
2
M5424-3SC
M5432-SC
M5432-3SC
3.5
3
M5434-3SC
M5452-SC
M5452-3SC
M5454-3SC
5
Monterey
Prestwick
Riviera
9 x 14
GPM 218
Upper 8
Middle 5 x 9
Lower 3 x 13
GPM 169
Upper 10 x 10
Lower 5 x 30
GPM 188
Upper 15
Middle 9 x 12
Lower 3 x 10
GPM 79
12 x 18
GPM 253
Upper 12
Middle 7 x 10
Lower 4 x 17
GPM 176
Upper 10 x 12
Lower 5 x 32
GPM 237
Upper 20
Middle 11 x 12
Lower 4 x 10
GPM 91
14 x 20
GPM 275
Upper 16
Middle 11 x 13
Lower 7 x 23
GPM 177
Upper 12 x 14
Lower 5 x 35
GPM 255
Upper 21
Middle 12 x 14
Lower 4 x 12
GPM 86
18 x 24
GPM 410
Upper 19
Middle 13 x 15
Lower 8 x 27
GPM 351
Upper 13 x 18
Lower 6 x 40
GPM 452
Upper 30
Middle 18 x 16
Lower 9 x 20
GPM 126
NOZZLES REQUIRING FLOW STRAIGHTENERS
M5414-3SC
M5422-3SC
Medinah
440-480 - 3PH
3.1
208-240 - 1PH
15.2
208-240 - 3PH
10.1
440-480 - 3PH
5.1
208-240 - 1PH
27.1
208-240 - 3PH
18.0
440-480 - 3PH
9.0
Royal
Somerset
Turnberry
Valhalla
Upper 6 x 24
Lower 3 x 32
GPM 204
Upper 12
Lower 6.5 x 16
GPM N/A
5.5 x 1.5
GPM 226
Upper 10
Middle 7 x 14
Lower 3 x 35
GPM 222
Upper 6.5 x 24
Lower 3.5 x 30
GPM 242
Upper 14
Lower 7.5 x 18
GPM N/A
7 x 18
GPM 278
Upper 12
Middle 8 x 20
Lower 4 x 35
GPM 251
Upper 7.5 x 38
Lower 4 x 38
GPM 251
Upper 17
Lower 9 x 22
GPM N/A
8 x 20
GPM 300
Upper 16
Middle 10 x 20
Lower 4 x 40
GPM 269
Upper 8.5 x 38
Lower 4 x 42
GPM 465
Upper 20
Lower 11.5 x 25
GPM N/A
10 x 23
GPM 391
Upper 18
Middle 12 x 20
Lower 5 x 45
GPM 414
Page 12
03/16
TABLE 1: THE MASTERS SERIES® PERFORMANCE SPECIFICATIONS (cont.)
TECHNICAL DATA
REFERENCE MATERIAL FOR SECTION 2.0 DETAILED INFORMATION
Model
Number
HP
M5410-SC
M5412-SC
M5412-3SC
1
M5414-3SC
M5422-SC
M5422-3SC
2
M5424-3SC
M5432-SC
3.5
M5432-3SC
Voltage
and
Phase
Running Amp
Draw
120 - 1PH
19.0
208-240 - 1PH
9.6
208-240 - 3PH
5.4
440-480 - 3PH
2.7
208-240 - 1PH
12.6
208-240 - 3PH
6.3
440-480 - 3PH
3.1
208-240 - 1PH
15.2
208-240 - 3PH
10.1
440-480 - 3PH
5.1
208-240 - 1PH
27.1
208-240 - 3PH
18.0
440-480 - 3PH
9.0
3
M5434-3SC
M5452-SC
M5452-3SC
M5454-3SC
5
ADJUSTABLE NOZZLES W/FLOW
STRAIGHTENERS
SPECIALTY NOZZLES W/FLOW
STRAIGHTENERS
Reflection
Sanibel
Captiva
Upper 7 x 16
Lower 3 x 22
GPM 273
11 x 14
GPM 172
9x4
GPM 141
Upper 9 x 20
Lower 3 x 30
GPM 307
15 x 17
GPM 186
12 x 4
GPM 177
Upper 12 x 26
Lower 3 x 30
GPM 354
16 x 18
GPM 199
15 x 5
GPM 223
Upper 13 x 16
Lower 4 x 37
GPM 485
19 x 20
GPM 406
19 x 7
GPM 290
*All performance data (heights and diameters), have been tested at 240 volt single phase electrical.
Your overall performance may vary due to actual voltage, intake restrictions and cable lengths.
Page 13
03/16
TABLE 2: CABLE SIZING CHARTS
Maximum recommended length (in feet) from fountain aerator to control panel
AquaMaster® recommends consulting a Licensed Electrician to properly size any underground cable from the main power source
to our control panel. Cable runs to the panel located away from main power source requires recalculating voltage drop to insure
proper cable sizing. Please contact AquaMaster® if assistance is required.
Unit
1HP
1HP
2HP
3.5HP
5HP
4 conductor: Required on all 1 - 10HP Single Phase & Three Phase Aerators
Single Phase 4 conductor
4 conductor Copper Wire Gauge Size
Approx
Volts
Amps
#14
#12
#10
#8
#6
#4
120
208-240
208-240
208-240
208-240
19.0
9.6
12.6
15.2
27.1
------
-271
206
---
Three Phase 4 conductor
132
451
344
285
--
202
694
529
439
246
322
1105
842
698
392
509
1747
1331
1104
619
#2
789
2708
2063
1711
959
4 conductor Copper Wire Gauge Size
Unit
Volts
Approx
Amps
#14
#12
#10
#8
#6
#4
#2
1HP
208-240
5.4
--
556
927
1426
2269
3587
5560
1HP
440-480
2.7
--
2352
3920
6031
9601
15176
23522
2HP
208-240
6.3
--
477
794
1222
1945
3075
4766
2HP
440-480
3.1
--
2049
3415
5253
8362
13218
20487
3HP
208-240
10.1
--
297
495
762
1213
1918
2973
3HP
440-480
5.1
--
1245
2076
3193
5083
8034
12453
5HP
208-240
18.0
--
5HP
440-480
9.0
-Actual voltage to motor will affect your fountain’s performance.
--
278
428
681
1076
1668
706
1176
1809
2880
4553
7057
Page 14
03/16
TABLE 3: FOUNTAIN AERATOR SPRAY PATTERN DESCRIPTIONS
1.
Masters Series® ACE - Basic Flow Pattern (BFP)
Full circle, two-tiered pattern with multi-point center formation.
SPECIFICATION DESCRIPTION: POINTED FAN SHAPE
2.
Masters Series® ARABELLA – Straightened Flow Pattern (SFP)
Sparkling, two-tiered pattern consisting of an upper multi-stream and a lower full conical
spray design.
SPECIFICATION DESCRIPTION: COMBINED FAN AND STREAMS
3.
Masters Series® AUGUSTA – Straightened Flow Pattern (SFP)
Beautiful multi-tiered streamed pattern with a center geyser to add height.
SPECIFICATION DESCRIPTION:
FAN SHAPE INDIVIDUAL STREAMS WITH
CENTER GEYSER
4.
Masters Series® BAYSIDE – Straightened Flow Pattern (SFP)
Narrower version of Red Tail, excellent in smaller contained areas.
SPECIFICATION DESCRIPTION: COMBINED FAN AND STREAMS
5.
Masters Series® BAYTREE – Straightened Flow Pattern (SFP)
Frothy tri-tiered pattern providing aeration benefits beautifully.
SPECIFICATION DESCRIPTION: TRI-TIER FROTHY SPRAY
6.
Masters Series® BIRDIE - Basic Flow Pattern (BFP)
Creates a dense, round ball of water, perfect for smaller containments of water.
SPECIFICATION DESCRIPTION: ROUND
7.
Masters Series® BISCAYNE - Basic Flow Pattern (BFP)
Variation of classic two-tier with taller, narrower lower spray.
SPECIFICATION DESCRIPTION: UPRIGHT FAN & COLUMN
8.
Masters Series® CAPTIVA – Specialty Pattern
Heavy-water vertical frothy column, excellent in open areas.
SPECIFICATION DESCRIPTION: DENSE FROTHY COLUMN
9.
Masters Series® CHAMPION – Straightened Flow Pattern (SFP)
Multi-stream pattern with specific points resulting in a dramatic surface effect.
SPECIFICATION DESCRIPTION: INDIVIDUAL STREAMS FAN SHAPE
10.
Masters Series® COLONIAL – Straightened Flow Pattern (SFP)
Two tier pattern that has a narrow center geyser, surrounded by a multi-streamed lower tier.
SPECIFICATION DESCRIPTION: FAN SHAPED INDIVIDUAL STREAMS WITH
CENTER GYESER
Page 15
03/16
TABLE 3: FOUNTAIN AERATOR SPRAY PATTERN DESCRIPTIONS (cont.)
11.
Masters Series® CROWN & GEYSER - Basic Flow Pattern (BFP)
A beautiful, dramatic pattern still achieves aeration results. This nozzle combines the
Lakewood Full Flow with the vertical Geyser column of water through its center.
SPECIFICATION DESCRIPTION: COMBINED FAN & COLUMN
12.
Masters Series® CRYSTAL GEYSER- Basic Flow Pattern (BFP)
This nozzle produces a very decorative crystalline spray pattern in an abstract, multi-tiered
formation.
SPECIFICATION DESCRIPTION: FROTHY SPRAY
13.
Masters Series® DIAMONDBACK – Straightened Flow Pattern (SFP)
Low height pattern sending streams of water in tremendous diameter.
SPECIFICATION DESCRIPTION: WIDEST LOW FAN SHAPE
14.
Masters Series® DORAL – Straightened Flow Pattern (SFP)
A two-tiered multi-streamed arch pattern.
SPECIFICATION DESCRIPTION:
TWO TIERED FAN SHAPED INDIVIDUAL
STREAMS
15.
Masters Series® DOUBLE EAGLE – Straightened Flow Pattern (SFP)
Statuesque, frothy vertical pattern creates a stunning full profile.
SPECIFICATION DESCRIPTION: SOLID VERTICAL COLUMN
16.
Masters Series® EAGLE - Basic Flow Pattern (BFP)
Elongated, frothy vertical pattern creates a beautiful, full profile.
SPECIFICATION DESCRIPTION: FROTHY VERTICAL COLUMN
17.
Masters Series® FIRESTONE – Straightened Flow Pattern (SFP)
Beautiful tri-tier, perfect for smaller area applications.
SPECIFICATION DESCRIPTION: TRI-TIER MULTIPLE STREAMS
18.
Masters Series® GEYSER - Basic Flow Pattern (BFP)
A multi-port nozzle achieves a dramatic vertical pattern in a solid column of water, fanning
slightly at the top.
SPECIFICATION DESCRIPTION: SOLID VERTICAL COLUMN
19.
Masters Series® HALF MOON – Straightened Flow Pattern (SFP)
Gorgeous multi-stream pattern results in a full floral effect.
SPECIFICATION DESCRIPTION: SCALLOPED FAN SHAPE
Page 16
03/16
TABLE 3: FOUNTAIN AERATOR SPRAY PATTERN DESCRIPTIONS (cont.)
20.
Masters Series® IMPERIAL – Straightened Flow Pattern (SFP)
Spectacular tri-tier, multiple-point rotating formation creating a dramatic effect.
SPECIFICATION DESCRIPTION: ROTATING COMBINED FAN AND STREAMS WITH
CENTER GEYSER
21.
LAKEWOOD - Basic Flow Pattern (BFP)
Internal impeller technology creates this full, more upright cone pattern, without a nozzle.
This is the base model for The Masters Series®.
SPECIFICATION DESCRIPTION: FAN SHAPE
22.
Masters Series® MEDINAH – Straightened Flow Pattern (SFP)
Taller, narrower version of the Turnberry.
SPECIFICATION DESCRIPTION: NARROW FAN SHAPE
23.
Masters Series® MONTEREY – Straightened Flow Pattern (SFP)
Frothy tri-tiered pattern combines both aesthetics and aeration.
SPECIFICATION DESCRIPTION: TRI-TIER FROTHY SPRAY
24.
Masters Series® PAR - Basic Flow Pattern (BFP)
Heavy-water version of the Crown & Geyser, excellent choice in open areas.
SPECIFICATION DESCRIPTION: DENSE COMBINED FAN & COLUMN
25.
Masters Series® PRESTWICK – Straightened Flow Pattern (SFP)
Dramatic multi-streamed two-tiered pattern.
SPECIFICATION DESCRIPTION: TWO-TIERED MULTIPLE STREAMS
26.
Masters Series® REFLECTION – Adjustable Straightened Flow Pattern (ASFP)
Dazzling, full circle, two-tiered pattern with multiple-point formation.
SPECIFICATION DESCRIPTION: ADJUSTABLE COMBINED FAN AND STREAMS
27.
Masters Series® RIVIERA – Straightened Flow Pattern (SFP)
Dazzling, three tier display that combines a narrow multi-streamed geyser with two
surrounding conical shaped tiers. Great for applications that require a tiered, narrower
pattern.
SPECIFICATION DESCRIPTIION:
TWO TIERED FAN SHAPED INDIVIDUAL
STREAMS WITH CENTER GEYSER
28.
Masters Series® ROYAL – Straightened Flow Pattern (SFP)
Spectacular two-tier, multiple-point rotating formation creating a dramatic effect.
SPECIFICATION DESCRIPTION: ROTATING COMBINED FAN AND STREAMS
Page 17
03/16
TABLE 3: FOUNTAIN AERATOR SPRAY PATTERN DESCRIPTIONS (cont.)
29.
Masters Series® SANIBEL – Adjustable Straightened Flow Pattern (ASFP)
Taller and frothier version of Medina.
SPECIFICATION DESCRIPTION: NARROW FAN SHAPED
30.
Masters Series® SOMERSET – Straightened Flow Pattern (SFP)
Heavy upright multi-stream fan shape with a geyser creates a stunning full profile pattern.
SPECIFICATION DESCRIPTION: HEAVY INDIVIDUAL STREAM FAN SHAPE WITH
CENTER GEYSER
31.
Masters Series® TURNBERRY – Straightened Flow Pattern (SFP)
Upright funnel shape creates a stunning full profile pattern.
SPECIFICATION DESCRIPTION: HEAVY FAN SHAPE
32.
Masters Series® VALHALLA – Straightened Flow Pattern (SFP)
Stunning tri-tier resulting in both excellent height and diameter.
SPECIFICATION DESCRIPTION: TRI-TIER SPRAY
33.
Masters Series® WIDE GEYSER - Basic Flow Pattern (BFP)
A modification of the Geyser nozzle produces a less dense, more decorative version.
SPECIFICATION DESCRIPTION: WIDE VERTICAL COLUMN
Page 18
03/16
TABLE 4: FOUNTAIN AERATOR LIGHTING SYSTEMS
AQUAMASTER® FOUNTAIN AERATORS are even more dramatic at night, with the addition of a
UL and cUL Listed NIGHT GLOW LIGHTING SYSTEM.
Any lighting system choice includes stainless steel lamp housings, sealed with clear tempered glass
lenses in a stainless steel clamp ring. All lights remain water-cooled.
All necessary electrical controls, including timer, are pre-wired into the fountain’s existing UL Listed
control panel. Color board assemblies (White, Red, Green, Blue, or Amber) must be selected for
each light. An optional sequencer can complete your dramatic aquatic display.
For uniformity of spray pattern coverage, 4 lights minimum is recommended.
LINE VOLTAGE: 120 Volt LED Lighting Systems
11 Watt Fixtures
4 light system: Model #870747
Each system includes:
•
11, 22, or 35 Watt LED light engine
22 Watt Fixtures
2 light system: Model # 870607
3 light system: Model # 870608
4 light system: Model # 870595
6 light system: Model #870609
8 light system: Model #870610
•
GFCI Protection
•
Digital Timer
•
Clear lenses
•
UL and cUL Listing
•
Choice of Red, Green, Blue, or Amber
Light Engine
35 Watt Fixtures
2 light system: Model # 870792
3 light system: Model # 870793
4 light system: Model # 870794
6 light system: Model # 870795
8 light system: Model # 870796
LINE VOLTAGE: 120 Volt RGBW LED Lighting Systems
40 Watt Fixtures
2 light system: Model # 870677
3 light system: Model # 870678
4 light system: Model # 870679
Each system includes:
•
40 Watt RGBW LED light engine
•
GFCI Protection
•
Digital Timer
6 light system: Model # 870680
8 light system: Model # 870681
•
Clear lenses
•
UL and cUL Listing
Page 19
03/16
TABLE 4: FOUNTAIN AERATOR LIGHTING SYSTEMS (cont.)
CABLE SIZING CHART FOR LED LIGHTS
Maximum recommended length (in feet) from fountain lights to control panel.
AquaMaster® recommends consulting a Licensed Electrician to properly size any underground cable from the main power
source to our control panel. Cable runs to the panel located away from main power source requires recalculating voltage drop to
insure proper cable sizing. Please contact AquaMaster® if assistance is required.
3 Conductor
Watts Per
Fixture
# of Fixtures
11
22
22
22
Copper Wire Gauge Size
Volts
Approx
Amps
#14
#12
#10
4
2
3
4
120
120
120
120
0.367
0.283
0.425
0.567
2639
3416
2277
1708
4091
5294
3529
2647
6818
8824
5882
4412
22
6
120
0.850
1139
1765
2941
22
35
35
35
35
8
2
3
4
6
120
120
120
120
120
1.133
0.583
0.875
1.167
1.750
854
1659
1106
829
553
1324
2571
1714
1286
857
2206
4286
2857
2143
1429
35
8
120
2.333
415
643
1071
Cable Sizing Chart for lights when ordered with a sequencer
3 & 4 Conductor see notes below
Copper Wire Gauge Size
Watts Per
Fixture
# of Fixtures
Volts
#14
#12
#10
11
3 or 4
120
10558
16364
27272
22
22
3 or 4
6 (3 colors)
120
120
6832
3416
3227
1614
17648
8824
22
8 (4 colors)
120
3416
1614
8824
35
35
3 or 4
6 (3 colors)
120
120
3318
1659
1567
784
8572
4286
35
8 (4 colors)
120
1659
784
4286
Lighting sequencer requires 2 runs of cable:
1) Sequencer with 3 colors require (1) run of 3 conductor cable and (1) run of 4 conductor cable
2) Sequencer with 4 colors require (2) runs of 4 conductor cable
CABLE SIZING CHART FOR RGBW LED LIGHTS
5 Conductor
Watts Per
Fixture
# of Fixtures
40
40
40
40
40
Copper Wire Gauge Size
Volts
Approx
Amps
#14
#12
#10
2
3
4
6
120
120
120
120
0.667
1.000
1.333
2.000
1452
968
726
484
2250
1500
1125
750
3750
2500
1875
1250
8
120
2.667
363
563
938
Page 20
03/16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising