S E R I E S
Product Reference Guide
Read and follow the instructions contained within carefully before use. Retain this guide in a safe and easily accessible place for future reference.
Drawings, pictures and specifications contained in this manual are for illustration purposes only – actual product may vary. VALCO BABY reserves the right to alter any specification(s), colour or features without prior notice or incurring any obligation to similarly alter products previously purchased.
Thank you for purchasing a quality VALCO product. Due to our policy of continuous product development, this product is constantly evolving. It is possible that some features or procedures outlined here have changed since this document was written. If you are unsure of any procedure outlined here please contact the store from which you purchased it to obtain the most up to date information, or contact us via the internet. See relevant web contact addresses on the back page.
Stroller Assembly/Opening
Carefully remove the stroller contents from the carton and dispose of all packaging immediately including any black rubber protectors on either side of the brake bar and front wheel protector. The front wheel forks, rear wheels, front bar and hood all need to be installed prior to use.
1. Lay the stroller flat on the floor.
2. Simultaneously pressing the buttons on either side pivot the handle to the fully extended position.
3. Lift the handle upward to a vertical position until the chassis locks in the open position.
1. Insert the rear axle housing
(with brake facing the away from the stroller) over each of the rear legs.
2. Push upward and over each metal button, until each lock securely into place.
2. Swivel the front of the seat and push down into the front slots, engaging the locking mechanism.
You may need to push down and hold the red spring lock for the front pins to engage in the front slots
1. Pressing on the centre hub button, insert the SQR axle through the outside of the metal hub in each wheel.
IMPORTANT : Insert axles through the outside of the wheel - the side which does NOT have the nylon brake cog)
3. IMPORTANT : Always engage the secondary safety lock to avoid inadvertent operation of the seat release mechanism.
1. Pressing the axle button, insert the protruding long axle into the opening in the tube at the rear of the stroller chassis.
2. Repeat this procedure for the other side.
Insert the seat section into the frame:
1. Insert the 2 rear locking pins on either side of the seat frame into the slots in the metal side bars of the frame
NOTE : Your seat can be inserted into the chassis facing either direction.
I MPORTANT WARNING: Always engage the secondary safety lock and test that the seat is securely engaged before use.
Installing/Removing the rear wheels
1. To remove the wheel simply press the axle button in the centre of the wheel hub and simultaneously pull the wheel outward.
IMPORTANT WARNING: Always test that the axles/wheels are securely engaged before use.
Installing/Removing and using the front wheel
Your Rebel stroller utilizes our unique and revolutionary new
DURAGLIDE™ front swivel system:
1. To install the front fork, tilt the stroller frame upward on the rear wheels.
2. Line up the fork shaft and insert it into the DURAGLIDE housing till it “clicks” into place.
IMPORTANT: Test that the fork is securely engaged in the housing.
Folding/Opening your stroller
1. Fully recline the seat. (this makes the folded stroller smaller).
2. Simultaneously press down on the frame release buttons and lift the safety release.
To remove the front fork:
1. Simultaneously push and turn the DURAGLIDE™ release button.
2. The fork will then be released.
HINT: You may need to apply a little downward pressure for the fork to fully disengage.
3. Swing the handle downward and collapse the stroller
5. Adjust the handle to make your stroller even smaller.
Your REBEL stroller can also stand unaided for easy storage by adjusting the handle angle.
1. To open, unhook the frame locking strap. (you may need to press down slightly on the frame to allow the strap to be released)
2. Lift the handle and the stroller will open from underneath.
The simple yet effective HEXLOK™ wheel locking system is perfect for rough terrain and beachside use.
1. To lock your wheel, rotate it so that it is beneath the chassis (as in normal use).
2. Grasping the HEXLOK™ on either side, slide the sleeve downward over the hexagonal top of the wheel fork, as far as it will go.
3. To disengage, reverse the process.
4. You can lock the frame closed by stretching the locking strap over the frame, placing the metal catch over the rivet on the chassis.
3. Continue lifting the handle upward until the stroller locks in the open position.
Adjusting your
Seat
To adjust the seat recline:
1. Lift the metal bar at the rear of the seat to release the seat backrest locks.
2. While the bar is still raised, move the backrest to the desired recline position.
To raise the seat:
1. Lift the backrest and the seat will automatically lock into the next raised position.
2. Continue until the desired position is reached.
The front bar
1. To install the front bar: Align the bar with the plastic housings on either side of the seat frame.
2. Insert the bar into the plastic housing so that the flexible centre piece engages in the housing.
3. To adjust the front bar:
Simultaneously press the 2 buttons in the centre of the round plastic and swivel the bar (forward or backward) to the desired position.
4. To remove the front bar: Feeling the side of the nylon housing that sits below the frame at each side (facing inward); locate the release “button.”
5. Press the release button inward while simultaneously pushing upward on the bar housing. Repeat for the other side.
Adjusting your
Footrest
Your footrest is adjustable to 3 positions:
1. To lower the footrest, simultaneously press the release buttons and move to the desired position.
2. To raise the footrest simply lift it to the desired position. It will automatically lock in the next upper position.
Using the brakes
1. Press down on the centre of the brake bar until the bar ends engage in the nylon brake cogs on the wheel.
IMPORTANT: Always check that the brake is fully engaged before use.
2. To disengage, lift the brake bar upward till it locks in the upright position.
Installing your hood
1. Identify the 2 slots in the fabric at e ither side of the seat section.
2. Line the two sections of the plastic anchors of the hood with the housing on the seat frame.
3. Insert the hood anchors into the housing.
4. Push downward until the flexible
“tongues” engage in the housing.
WARNING : NEVER lift the seat (or the entire pram) by the hood.
Extras
Your REBEL stroller includes a fitted rain cover, tyre pump and fitted boot cover.
Boot cover installation:
1. Slip the bottom “pocket” of the boot cover beneath the footrest.
2. Secure the boot cover to the hood with the press studs.
IMPORTANT WARNING: Never use the front bar to carry the stroller or as a restraining device.
Reversing your seat
Your seat has been designed with a reversible seat. This means it can be assembled as to allow the child to face in either direction.
1 2
3
NEVER REMOVE/REVERSE
THE SEAT SECTION WITH A
CHILD IN IT!
Using your harness
1. Lift the secondary seat security latch clear of the release bar.
2. Press down on the red release lever and swivel the seat upward so that it is resting on the rear pegs in the rear slots in the chassis.
3. Remove the Seat from the chassis and turn so that it faces in the desired direction.
4. Place the rear pegs in the seat in
5. the slots at the rear of the chassis
Pivot the seat downward and secure.
(refer to the procedure outlined in the assembly section of this guide)
Your Rebel stroller is fitted with two 5 point safety harness systems. Your child MUST always be harnessed while in the stroller.
1.
2.
3.
4.
TO SECURE YOUR CHILD IN THE HARNESS:
Insert Buckles (A) and (B) into either side of the Buckle Housing (C). Keep inserting until they click into place securely.
Carefully adjust the harness straps to snugly fit your child by adjusting the Sliders (D) located on all Shoulder Straps, Waist Straps and the Crotch Strap.
Your harness can be adjusted for even more comfort at the top of the seat for smaller or larger children by threading/removing the shoulder and crotch straps through the webbing sewn into the seat.
To prevent older children tampering with the strap adjustments and for greater child comfort, your REBEL stroller is provided with 2 soft strap covers for each harness. To fit, disengage each shoulder strap from the central buckle housing and thread the strap through the cover.
Re-install the straps to the central buckle housing.
The harness should be snugly fitted to the baby’s body, tight enough so that the baby cannot wriggle itself free of the straps but loose enough so as not to cause the baby any discomfort.
TO OPEN THE HARNESS:
1. Release the Buckle Prongs – Squeeze on the top and bottom prongs simultaneously and pull apart from the Buckle Housing.
This process may be difficult, as your buckle system has been designed to meet very stringent safety standards to ensure that a child cannot release the harness unaided.
OPTIONAL/ADDITIONAL ACCESSORIES
Toddlerseat
Available in versions for Rebel models, the optional toddlerseat sits firmly inside the chassis. Perfect for when a new baby comes along and junior still likes to go for a ride! The Rebel even folds totally out of the way with the stroller! See your local specialist retailer for more info and suitability.
Newborn Head Hugger and Strap Covers
Inner Tube
Tire Pump
Fitted all season
Footmuff/Sleeping bag
Mounted Bottle Holder
(Holds most bottles up to 1.5 litres)
Sunstopper (Universal fit)
The unique SUNSTOPPER provides the ultimate protection from the suns harsh rays, while providing a comfortable open environment for the child. The unique roll up blind system means that the child can be shielded from the sun without being fully enclosed, and folds up into its own self enclosed pouch for easy storage. Travel Storage Bag
(single version only)
OPTIONAL ACCESSORIES
The VALCO HITCHHIKER is a boon to any parent with a child who is old enough to walk but young enough to need to rest along the way. Made of high quality and extremely sturdy materials (maximum weight 30 kg’s / 66 lb’s), the HITCHHIKER is easily adjustable for height, width and distance from the stroller which makes it fit most brands, makes and models of strollers. The handy “hang up” system means it can hang out of the way when not in use, while the unique quick release systems allows for quick and easy removal.
All this and more makes the HITCHHIKER the perfect option for that “in between” age child.
See your local specialist retailer for more information.
WARNINGS
Your child’s safety is your responsibility ………
Be sure to check that all clamps and buckles are securely fixed and in place before use.
Be sure to check that all nuts and bolts are securely fixed and in place before use
Check all parts for breakage or fatigue before use. Discontinue immediately if any part is found to be damaged or broken.
The maximum weight of the child for which this stroller is intended is 22 kg’s (48 lbs)
Can be used from birth +. A cocoon specially designed to be used with a stroller is recommended when any fully reclining stroller is used with a newborn.
NEVER jog with a newborn baby in any pram or stroller until the child can sit up
unassisted (approximately 6 months).
ALWAYS ensure that the child is clear of all moving parts when adjusting the stroller.
ALWAYS engage the brake system when the stroller is at rest.
NEVER leave any child unattended in the stroller.
NEVER remove or reverse the seat with a child in it
NEVER use on escalators or stairs.
When in the stroller the child must ALWAYS wear the safety harness, correctly fitted and adjusted, at all times.
DO NOT hang shopping bags from the handle as this may affect the stroller’s stability.
Always use the basket provided, the maximum weight in the basket is 6 kg’s (13 lbs)
Do not carry additional children. It may be unsafe to use any accessories other than VALCO approved ones.
ALWAYS be aware of the risks provided by fire and other significant sources of heat such as radiators etc. which may be in the immediate vicinity of your stroller.
This product is intended for domestic use only. It is not intended for commercial use.
Continued and extended exposure to sunlight and the elements can change the colours of many materials. To avoid fading, always cover and store in a shaded area.
I f your brakes do not engage, check to see that the nylon brake cogs are on the INSIDE of each wheel when it is attached to the chassis. If not, remove the wheel and SQR axle and re-insert the SQR axle from the other side of the wheel, so that the cog will be on the inside of the wheel.
Caring for your stroller
Moving parts may be lubricated with silicone based lubricants – do not use oil.
Your Rebel chassis is made of aluminium alloy but does include some metal parts. Special care must always be taken to avoid rust. If this pram is used near the ocean or salty air environments, spray the chassis and seat frame with water and dry thoroughly. This is particularly important for parts such as wheel axles and springs. We recommend rust inhibiting product should be applied to prevent accelerated rust and fatigue of these metal parts!
We recommend that you wipe down axles and lubricate the wheels every 3 months, particularly the front wheel and housing. Sand and dirt can grind down axles so, if you live, walk or run near/on the beach or in a dusty environment, you must remove and wipe down the axles and wheels, then lubricate them MONTHLY.
AXLES AND MOVING PARTS ARE BEST LUBRICATED WITH SILICONE BASED
PRODUCTS. DO NOT USE OIL BASED PRODUCTS.
In Australia/NZ www.valco.com.au
www.valco.co.nz
In North America www.valcobaby.com
1 800 610-7850
© Copyright VE 2005