OrigoMig C420 PRO
GB
Origo™
Mig C420 PRO
Instruction manual
0463 272 001 GB 20110808
Valid for serial no. 627-xxx-xxxx, 120-xxx-xxxx
-2-
1 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1
4
6
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
3 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
8
4.1 Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Assembly of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 Electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4 Mains power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8
9
9
9
5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
Connection and control devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overheating protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water flow guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mig C420w PRO / Mig C420 PRO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Polarity change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wire feed pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing and inserting wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
11
12
12
12
12
12
13
13
14
6 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
6.1
6.2
Inspection and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Topping up the coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
16
7 FAULT TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 ORDERING OF SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WEAR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
18
20
22
24
Rights reserved to alter specifications without notice.
TOCe
-3-
GB
1
SAFETY
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or
near the equipment observes all the relevant safety precautions. Safety precautions must meet the
requirements that apply to this type of equipment. The following recommendations should be ob­
served in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the equip­
ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in­
jury to the operator and damage to the equipment.
1.
Anyone who uses the equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding and cutting
2.
The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no-one is unprotected when the arc is struck
3.
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame-proof
clothing, safety gloves.
S Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5.
General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
WARNING
Do not use the power source for thawing frozen pipes.
-4bc24de
© ESAB AB 2011
GB
WARNING
Arc welding and cutting can be injurious to yourself and others. Take precausions when welding and
cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard
data.
ELECTRIC SHOCK - Can kill
S
Install and earth the unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
Read and understand the instruction manual before installing or operating.
PROTECT YOURSELF AND OTHERS!
CAUTION
Class A equipment is not intended for use in residential locations where
the electrical power is provided by the public low-voltage supply system.
There may be potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations, due to conducted
as well as radiated disturbances.
CAUTION
Read and understand the instruction manual before
installing or operating.
CAUTION
This product is solely intended for arc welding.
-5bc24de
© ESAB AB 2011
GB
Dispose of electronic equipment at the recycling facility!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical and/or
electronic equipment that has reached the end of its life must be disposed of at a
recycling facility.
As the person responsible for the equipment, it is your responsibility to obtain
information on approved collection stations.
For further information contact the nearest ESAB dealer.
ESAB can provide you with all necessary welding protection and accessories.
2
INTRODUCTION
The Mig C420 PRO is a step-controlled compact welding power source incorporating
wire feed mechanism intended for MIG/MAG welding with solid wires of steel,
stainless steel or aluminium, and cored wires with or without shielding gas.
The Mig C420w PRO is equipped with a cooling liquid system for welding torches.
The Mig C420 PRO is not equipped with a cooling system and can operate only with
appropriate gas cooled torches.
The power units are fan-cooled and equipped with thermal overload protection.
The machines can be fitted with a flow guard (Mig C420w PRO).
The power source comes in different variants, see page 20.
ESAB's accessories for the product can be found on page 24.
2.1
Equipment
The power source is supplied with:
S
Welding gun PSF 405/410w - 4,5m
S
Return cable 5m with return clamp
S
Shelf for gas cylinder
S
Instruction manual
-6bc24de
© ESAB AB 2011
GB
3
TECHNICAL DATA
Voltage
Permissible load
at100 % duty cycle
at 60 % duty cycle
at 50 % duty cycle
Setting range (DC)
Open circuit voltage
Open circuit power
with cooling unit
Mig C420 PRO
400-415V, 3∼50Hz
315 A/30V
400 A/34V
420 A/35V
50A/16,5V-420A/35V
14-47V
520W
730W
Efficiency
Power factor
Control voltage
Wire feed speed
77%
0,92
42V, 50/60Hz
1,9 - 25,0m/min
Burnback time
0 - 0,5s
Creep start
OFF / ON
2/4 stroke
2/4
Welding gun connection
EURO
Max diameter of wire bobbin
300mm
Wire dimension range
0,6 - 1,6mm
Dimensions LxWxH
Weight
with cooling unit
935 x 640 x 800mm
215kg
230kg
Operating temperature
-10 to +40oC
Transportation temperature
-20 to +55oC
Enclosure class
IP 23
Application classification
Cooling unit (100 % duty cycle)
P1l/min
1200 W at 25° C
pmax
3,5 bar
Coolant
ESAB's ready mixed coolant
Coolant quantity
5,5 l
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at
a certain load without overloading. The duty cycle is valid for 40° C.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol
indicates that the power source is designed for use in areas with increased
electrical hazard.
-7bc24de
© ESAB AB 2011
GB
4
INSTALLATION
The installation must be carried out by a professional.
Note!
Connect the power source to the electricity mains with a network impedance of 0.268W or lower. If the
network impedance is higher, there is a risk of flicker in the illuminators.
CAUTION
This product is intended for industrial use. In a domestic environment this product may
cause radio interference. It is the user's responsibility to take adequate precautions.
4.1
Location
Position the welding power in source such a way that its cooling air inlets and outlets
are not obstructed.
WARNING
Straps must be used when lifting the power
source. The handle is only intended for
pulling it.
4.2
Assembly of components
-8bc24de
© ESAB AB 2011
GB
WARNING
During transport, the rear wheels of the power source are in their forward position.
Before use, place the wheels in their rear position.
4.3
Electrical installation
4.4
Mains power supply
Check that the unit is connected to the correct mains power supply voltage, and that
it is protected by the correct fuse size. A protective earth connection must be made,
in accordance with regulations.
Rating plate with supply connection data
-9bc24de
© ESAB AB 2011
GB
Recommended fuse sizes and minimum cable areas
Voltage V
Current A
at100% duty cycle
at 60% duty cycle
at 50% duty cycle
Cable area mm2
Fuse, slow A
3∼ 50 Hz
400-415
19
27
30
4x4
25
NB: The mains cable areas and fuse sizes as shown above are in accordance with Swedish
regulations. They may not be applicable in other countries: make sure that the cable area and fuse
sizes comply with the relevant national regulations.
5
OPERATION
General safety regulations for handling of the equipment can be found on
page 4. Read through before you start using the equipment!
WARNING
Rotating parts can cause injury, take great care.
WARNING
To prevent the reel from sliding off the hub: Lock the
reel in place by turning the red knob as shown on the
warning label attached next to the hub.
WARNING
Secure the equipment - particularly if the
ground is uneven or sloping.
- 10 bc24de
© ESAB AB 2011
GB
5.1
Connection and control devices
1
Mains supply switch
10
2
Switch, coarse control
11
3
4
5
Switch, precise control
Indicator lamp, power supply ON
Orange indicating lamp, overheating and
loss of coolant*
EURO - connector (for welding gun)
Connection for cooling water to the welding
gun (Blue - with ELP** switch)
Connection for cooling water from the
welding gun (Red)
12
13
14
Knob for wire speed setting
Knob for selecting 2/4-stroke control mode
Knob for selecting - creep start - ON/OFF
15
16
Knob for burn-back time setting
Digital instrument - V / A ***
17
Water flow guard (option,see page 24)
6
7
8
9
Connection for return cable (-), medium
inductance
Connection for return cable (-), low
inductance
Connection for return cable (-), high
inductance
* Indicating loss of coolant, only when water flow guard is used, see point 5.5
** ELP = ESAB Logic Pump, see point 5.4.
*** NOTE! Digital instrument V/A only available on certain models.
5.2
Start
When switched on, indicator lamps [4,5] are on for 2 seconds. Normally, if the
machine is not overheated, it should start to work in idle mode, which is indicated by
blinking of the supply ON lamp. The fan and the coolant pump are stopped. The fan
starts at the first start of welding. The coolant pump starts at the same moment, if it
is switched on with ELP switch on the water outlet [7].
- 11 bc24de
© ESAB AB 2011
GB
5.3
Overheating protection
The power source has 2-step control of fan speed and overheating protection.
If temperature crosses the threshold point, the fan starts to run with increased
speed. If the internal temperature becomes too high, the welding is interrupted and
disabled. This state is indicated by permanent lighting of the orange indicating lamp
on the front of the unit. It resets automatically when the temperature falls down.
5.4
Water connection
The Mig C420w PRO has a sensor ELP, ESAB Logic Pump, which senses whether
the water hoses of the welding gun are connected. When a water-cooled welding
gun is connected, the water pump is active.
It is recommended to switch the power source off by means of the mains switch
ON/OFF [1] for connecting the cooling water hoses to/from the Mig C420w PRO.
5.5
Water flow guard
The machines with cooling unit (Mig C420w PRO) can be fitted with a water flow
guard (option - see page 24).
The water flow guard interrupts and disables welding in event of loss of coolant. This
state is indicated by the orange indicating lamp on the front of the power source
flashing. If there is a lack a coolant flow, after 1 min the pump is switched off and
locked in this state. The pump restarts from that state along with start of welding.
5.6
Idle mode
The machine has an idle mode. The fan is switched off 5 min after the end of the last
welding, or after 5 min of work with decreased speed without welding. The pump is
switched off 3 min after the last welding. When both fan and pump are switched off
the power supply lamp [4] on the front panel flashes.
5.7
Mig C420w PRO / Mig C420 PRO
The Mig C420w PRO / Mig C420 PRO is equipped with a standard control unit. The
welder can manually select and adjust all welding parameters.
S
Wire speed (1,9 - 25m/min) is set with knob [12].
S
The stroke control (2/4 stroke) is selected with switch [13].
S
Creep start i.e. start with 50% wire speed is toggled ON/OFF with switch [14].
S Burn back time is set with knob [15].
Mig C420w PRO / Mig C420 PRO can be fitted with a digital instrument that displays
current and voltage. It incorporates a hold function (see page 24).
- 12 bc24de
© ESAB AB 2011
GB
5.8
Polarity change
The power source is delivered with the welding wire connected to the plus pole.
Some wires, e.g self shielded cored wires, are recommended for welding with
negative polarity. Negative polarity means that the wire is connected to the minus
pole and the return cabel to the plus pole.
Check the recommended polarity for the welding wire you want to use.
5.9
Wire feed pressure
Start by making sure that the wire moves smoothly through the wire guide. Then
set the pressure of the wire feeder's pressure rollers. It is important that the
pressure is not too great.
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
Fig 1
Fig 2
To check that the feed pressure is set correctly, you can feed out the wire against
an insulated object, e.g. a piece of wood.
When you hold the gun approx. 5 mm from the piece of wood (fig. 1) the feed
rollers should slip.
If you hold the gun approx. 50 mm from the piece of wood, the wire should be
fed out and bend (fig. 2).
- 13 bc24de
© ESAB AB 2011
GB
5.10
Replacing and inserting wire
S
Open the side panel.
S
Disconnect the pressure sensor by folding it backwards, the pressure rollers
slide up.
S
Straighten out 10-20 cm of new wire. File off any burrs and sharp edges from the
end of the wire before inserting it into the wire feed unit.
S
Make sure that the wire goes properly into the feed roller track and into the outlet
nozzle and the wire guide.
S
Secure the pressure sensor.
S
Close the side panel.
6
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
Only those persons who have appropriate electrical knowledge (authorized
personnel) may remove the safety plates.
CAUTION
All guarantee undertakings from the supplier cease to apply if the customer attempts any
work to rectify any faults in the product during the guarantee period.
6.1
Inspection and cleaning
Power source
Check regularly that the power source is free from dirt.
The power source should be regularly blown clean using dry compressed air at reduced
pressure. This should be done more frequently in dirty environments.
Otherwise the air inlet/outlet may become blocked and cause overheating. To avoid this
you can use an airfilter.
The airfilter is an accessory. Order number can be found on page 24.
- 14 bc24de
© ESAB AB 2011
GB
- 15 bc24de
© ESAB AB 2011
GB
Welding gun
S
Cleaning and replacement of the welding gun’s wear parts should take place at
regular intervals in order to achieve trouble−free wire feed. Blow the wire guide
clean regularly and clean the contact tip.
The brake hub
The hub is adjusted when delivered, if
readjustment is required, follow the instructions
below. Adjust the brake hub so that wire is slightly
slack when wire feed stops.
S
Adjusting the braking torque:
S
Turn the red handle to the locked position.
S
Insert a screwdriver into the springs in the hub.
Turn the springs clockwise to reduce the braking torque
Turn the springs counter-clockwise to increase the braking torque. NB: Turn
both springs the same amount.
6.2
Topping up the coolant
ESAB's ready mixed coolant is recommended for use.
See accessories on page 24.
Note! Coolant must be topped up if connecting a
Push-Pull welding gun that is 6 meters in length or
longer. When adjusting the water level by topping
up, the coolant hose does not need to be
disconnected.
CAUTION
The coolant must be handled as chemical waste.
- 16 bc24de
© ESAB AB 2011
GB
7
FAULT TRACING
Try these recommended checks and inspections before sending for an authorised
service technican.
Type of fault
Actions
S
S
No arc
S
Welding current is interrupted
during welding
S
S
Check that the mains power supply switch is turned on.
Check that the welding current supply and return cables are
correctly connected.
Check that correct current value is set.
Check whether the thermal overload trip has operated
(indicated by the orange lamp on the front).
Check the main power supply fuses.
Thermal overload trips
operate frequently
S
S
Check to see whether the air filters are clogged.
Make sure that you are not exceeding the rated data for the
power source (i.e. that the unit is not being overloaded).
Poor welding performance
S
Check that the welding current supply and return cables are
correctly connected.
Check that the correct current value is set.
Check that the correct welding wires are being used.
Check the main power supply fuses.
Check the wire feed unit - that proper rolls are applied and
properly set the pressure of the wire feeder's pressure rollers
S
S
S
S
8
ORDERING OF SPARE PARTS
Repair and electrical work should be performed by an authorized ESAB service
technician. Use only ESAB original spare and wear parts.
Mig C420 PRO is designed and tested in accordance with the international and Euro­
pean standards EN 60974-1, EN 60974-5 and EN 60974-10. It is the obligation of the
service unit which has carried out the service or repair work to make sure that the pro­
duct still conforms to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
- 17 bc24de
© ESAB AB 2011
Diagram
- 18 bc24e
© ESAB AB 2011
- 19 bc24e
© ESAB AB 2011
Mig C420 PRO
Ordering number
Ordering no.
Type
Notes
0349 302 655 OrigoTM Mig C420 PRO
400−415V 3~50Hz
0249 303 079 OrigoTM Mig C420w PRO
400−415V 3~50Hz; with water cooler
0349 312 580 OrigoTM Mig C420 PRO
400−415V 3~50Hz, with digital instrument
0349 312 590 OrigoTM Mig C420w PRO
400−415V 3~50Hz; with water cooler and digital
instrument
0349 300 538 OrigoTM Mig C420 PRO
Spare parts list
The spare parts list is available on the Internet at www.esab.com
- 20 bc24o
© ESAB AB 2011
- 21 p
Mig C420 PRO
Wear parts
Item
Denomination
Ordering no.
Notes
A
Feed / pressure roller
0459 052 001
0459 052 002
0459 052 003
0459 052 013
0458 825 001
0458 825 002
0458 825 003
0458 824 001
0458 824 003
Ø 0.6 & 0.8 mm; Fe, Ss & cored wire; V-groove
Ø 0.8 & 1.0 mm; Fe, Ss & cored wire; V-groove
Ø 0.9/1.0 & 1.2 mm; Fe, Ss & cored wire; V-groove
Ø 1.4 & 1.6 mm; Fe, Ss & cored wire; V-groove
Ø 0.9/1.0 & 1.2 mm; Cored wire; V-groove; knurled
Ø 1.2 & 1.4 mm; Cored wire; V-groove; knurled
Ø 1.6 & 2.0 mm; Cored wire; V-groove; knurled
Ø 0.8 & 0.9/1.0 mm; Al wire; U-groove
Ø 1.2 & 1.6 mm; Al wire; U-groove
B
Gear adapter
0459 441 880
Replacing 0455 053 880
C
Inlet nozzle
0455 049 001
D
Drive gear
0459 440 001
Replacing 0455 052 001
E
Intermediate nozzle
0455 072 002
0456 615 001
Fe, Ss & cored wire
Al wire
F
Outlet nozzle
0469 837 880
0469 837 881
Ø 2.0 mm steel for 0.6-1.6 mm Fe, Ss & cored wire
Ø 2.0 mm plastic for 0.8-1.6 mm Al wire
G
Liner
0349 303 018
0455 894 001
Fe, Ss & cored wire
Al wire
The rollers are marked with wire dimension in mm, some are also marked with inch.
Welding with aluminium wires.
In order to weld with aluminium wires, proper rollers, nozzles and liners for aluminium wires MUST be
used. It is recommended to use 3m long welding gun for aluminium wires, equipped with appropriate
wear parts.
- 22 bc24w
© ESAB AB 2011
Mig C420 PRO
- 23 bc24w
© ESAB AB 2011
Mig C420 PRO
Accessories
Digital meter . . . . . . . . . . . . . . . . . .
0349 302 451
Transformer kit for CO2 heater . . . . . . . . . . .
0349 302 250
Water flow guard . . . . . . . . . . . . . .
0349 302 251
Coolant ready mixed (5 l) . . . . . . . . . . . . . . . .
0349 483 296
Filter . . . . . . . . . . . . . . . . . . . . . . . . .
0349 302 252
- 24 bc24a
© ESAB AB 2011
Mig C420 PRO
Cable holder . . . . . . . . . . . . . . . . . .
0349 303 362
Push-Pull connection kit . . . . . . . . . . . . . . . . .
0349 308 337
Push-Pull welding guns:
MXH 400w PP - 6,0m . . . . . . . . . . . . . . . . . . . . .
MXH 400w PP - 10,0m . . . . . . . . . . . . . . . . . . .
0700 200 015
0700 200 016
- 25 bc24a
© ESAB AB 2011
- 26 p
- 27 p
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
BULGARIA
ESAB Kft Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
ROMANIA
ESAB Romania Trading SRL
Bucharest
Tel: +40 316 900 600
Fax: +40 316 900 601
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
RUSSIA
LLC ESAB
Moscow
Tel: +7 (495) 663 20 08
Fax: +7 (495) 663 20 09
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB international AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
UKRAINE
ESAB Ukraine LLC
Kiev
Tel: +38 (044) 501 23 24
Fax: +38 (044) 575 21 88
ITALY
ESAB Saldatura S.p.A.
Bareggio (Mi)
Tel: +39 02 97 96 8.1
Fax: +39 02 97 96 87 01
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
Asia/Pacific
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
Africa
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
SOUTH AFRICA
ESAB Africa Welding & Cutting Ltd
Durbanvill 7570 - Cape Town
Tel: +27 (0)21 975 8924
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
www.esab.com
© ESAB AB
110426
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising