Read This First

Read This First
2-638-045-11 (1)
1
1
Digital Still Camera
2
Prepare the battery pack
2
Insert the battery pack.
Push the back part of the battery pack
gently until it clicks into place.
Read This First
Lift out the inlet plug and
connect to the wall outlet
(wall socket).
1
3
Turn the camera on/set the clock
Select
2
.
Open the lens cover or
press the POWER button.
Insert the “Memory Stick Duo”
all the way in until it clicks.
Battery charger
Before operating the unit, please read this manual and “User’s Guide/Troubleshooting” (separate
volume) thoroughly, and retain them for future reference.
3
CHARGE lamp
Plug
When there is no “Memory Stick Duo” inserted
Set the clock with the control
button.
z.
Clock Set
Y/M/D
M/D/Y
D/M/Y
2005 / 1 /
• Connect the battery charger to an easily accessible wall outlet (wall socket) close by.
• Even if the CHARGE lamp is not lit, the battery charger is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet (wall socket). If some trouble occurs while using the
battery charger, immediately shut off the power by disconnecting the plug from the wall outlet (wall socket).
• When charging is finished, disconnect the battery charger from the wall outlet (wall socket), and remove the
battery pack from the battery charger.
• The time required to fully charge the supplied battery pack from when it is completely discharged at a
temperature of 25°C (77°F) is approximately 220 min., and the practical charging time is approximately
160 min. Charging may take longer under certain circumstances or conditions.
3
• Battery charger BC-CS3 (1)
• Rechargeable battery pack
NP-FT1 (1)/Battery case (1)
• USB, A/V, DC IN cable for
multi-use terminal (1)
• Wrist strap (1)
A “Memory Stick Duo” is not
supplied.
The camera has its own internal
memory (32 MB), however,
purchase of a “Memory Stick
Duo” is recommended for
shooting more images.
“Memory Stick Duo”: you
can use a “Memory Stick
Duo” with your camera.
OK
AM
Cancel
• CD-ROM (Cyber-shot
application software) (1)
• Operating instructions: “Read
This First” (this manual) (1)
• Operating instructions:
“User’s Guide/
Troubleshooting” (1)
Other memory cards cannot
be used.
Still image:
Select
2005 / 1 /
Insert the charged battery pack.
1
12 : 00
OK
AM
Cancel
2005 / 1 /
3M
Movie:
Image Size
Select
1
.
10 : 30
OK
AM
Cancel
4
• To cancel, select [Cancel] and press z.
Close the battery/
“Memory Stick Duo”
cover.
You can connect the camera to a wall outlet (wall socket) using the AC-LS5K AC Adaptor (not
supplied). t “User’s Guide/Troubleshooting” (page 15). Refer to the operating instructions
supplied with the AC Adaptor.
Select [Clock Set] in the
(Setup) screen and perform the procedure in step 3 above.
t “User’s Guide/Troubleshooting” (pages 44 and 54)
The default settings are marked with
Open the lens cover or press POWER button to turn on and check the time on the LCD screen.
On the clock display
• If you selected [D/M/Y] in step 3-1, set the time on a 24-hour cycle.
• Midnight is indicated as 12:00 AM, and noon as 12:00 PM.
5M (2592×1944)
For printing in A4 size or high density
images in A5 size
• The displayed time remaining may not be correct under
certain circumstances.
• Unless you set the clock, the Clock Set screen appears each time the camera is turned on.
• The following screen appears when the camera is turned on for the second time or afterwards.
Battery eject lever
.
Guidelines
When turning on the power
Open the battery/“Memory Stick Duo” cover and slide the battery eject lever in the direction of
the arrow. Grasp the edges of the battery pack to pull the battery pack out. To avoid dropping the
battery pack, do not hold the camera with the battery slot facing down when the battery eject
lever is out.
For details on the image size t “User’s Guide/Troubleshooting” (page 12)
Image size
• It takes about one minute until the correct battery remaining
time appears.
Remaining time
Press
(Image Size) to
complete the setting.
button
On still image sizes
To check the remaining battery time
60min
When opening the lens cover
• If you open the lens cover too quickly, the camera might not turn on. If this
happens, close the cover and then open it again more slowly.
• When opening the lens cover, be careful not to touch the lens.
• Open the lens cover until it clicks.
No. of images
Printing
Less
Fine
More
Rough
3:2* (2592×1728)
3M (2048×1536)
1M (1280×960)
For printing in postcard size
VGA(E-Mail)
(640×480)
For recording a larger number of images
For attaching images to e-mail or creating
web pages
16:9(HDTV)**
(1920×1080)
For viewing images on a wide TV with a
“Memory Stick” slot
* Images are recorded in the same 3:2 aspect ratio as photograph printing paper or postcards, etc.
** Both edges of the image may be cut off when printing t “User’s Guide/Troubleshooting” (page 87)
On the recordable number of still images and recordable time of movies
Recordable number of still images and recordable time of movies vary depending on the image
size selected.
For details on recordable number or time t “User’s Guide/Troubleshooting” (page 21)
Still images
Movies
Maximum number of recordable images
To turn off the power
Notes
50 pic
• The screen above is for still images.
• For movies, select [640(Fine)] (“Memory Stick PRO
Duo” only), [640(Standard)] or [160].
• The recordable number of still images or the
recordable time of movies is indicated at the right
side of [Image Size].
To change the date and time
60min
Select the size with v / V.
VGA(E-Mail)
16:9(HDTV)
Using the AC Adaptor
Remaining indicator
3
(Image Size).
3:2
Y/M/D
M/D/Y
D/M/Y
Insert the battery pack while
pressing the battery eject lever
with the tip of the battery.
Press
.
Clock Set
Open the battery/
“Memory Stick Duo”
cover.
2
1M
3 Select [OK] with B, then press z.
• For details on “Memory Stick
Duo” t “User’s Guide/
Troubleshooting” (page 93)
• Charge the supplied NP-FT1 battery pack before using the camera for the first time.
• The LCD screen is manufactured using extremely high-precision technology so over 99.99% of the
pixels are operational for effective use. However, there may be some tiny black points and/or bright
points (white, red, blue or green in color) that constantly appear on the LCD screen. These points are
normal in the manufacturing process and do not affect the recording in any way.
• The camera is a precision instrument. Be careful not
Hook
to bump the lens or the LCD screen, and not to apply
force to it. Attach the strap to prevent the camera
from damage by being dropped, etc.
Select a mode.
Y/M/D
M/D/Y
D/M/Y
To remove the battery pack
“Memory Stick”: you cannot
use a “Memory Stick” with
your camera.
1
Clock Set
Battery eject lever
Checking the accessories supplied
12 : 00
4
Select the image size for use
with v/V, then press z.
Explains advanced techniques and what to do if you experience trouble with
your camera.
2638045110
1
2 Select each item with b/B and set the numeric value
Refer to “User’s Guide/Troubleshooting”
(separate volume)
© 2005 Sony Corporation Printed in Japan
The camera records/plays back images using the internal memory (32 MB). t “User’s Guide/
Troubleshooting” (page 22)
1 Select the date display format with v/V, then press
Light on: Charging
Light off: Completed (Practical charge)
If you continue charging the battery pack for about
one more hour (until it is fully charged), the
charge will last slightly longer.
Printed on 100% recycled paper using VOC
(Volatile Organic Compound)-free vegetable
oil based ink.
Terminal side
Lighting
Operating Instructions
DSC-T5
Insert a “Memory Stick Duo” (not
supplied)
Maximum recordable time
Close the lens cover or press the POWER button again.
To use your camera abroad — Power sources
You can use your camera, the supplied battery charger, and the AC-LS5K AC Adaptor (not
supplied) in any country or region where the power supply is within 100 V to 240 V AC,
50/60 Hz.
• Do not use an electronic transformer (travel converter), as this may cause a
malfunction.
• If the camera is running on battery power and you do not operate the camera for about three minutes, the
camera turns off automatically to prevent wearing down the battery pack (Auto power-off function).
Changing the language setting
• The number of recordable images and time can differ according to shooting conditions.
You can change the screen display to show messages in a specified language. To change the
language setting, press MENU to display the menu screen. Select
(Setup) with the control
button, then, select [ A Language] in
(Setup1), and select the desired language. t “User’s
1
Guide/Troubleshooting” (page 52)
To remove a “Memory Stick Duo”
Access lamp
Open the battery/“Memory Stick Duo” cover, then push the
“Memory Stick Duo” in once.
When the access lamp is lit
Additional information on this product and answers to frequently asked questions can be
found at our Customer Support Website.
Never remove the battery/“Memory Stick Duo” or turn off
the power. The data may be corrupted.
http://www.sony.net/
continued on the reverse
5
Shoot images easily (Auto adjustment mode)
Holding the camera
1
2
Select a mode.
Still image (auto adjustment
mode):
Select
Shoot still images (Scene Selection)
1
Shoot with the shutter button.
Select
2
.
Select
2
.
Select an image with b/B.
60min
Press and hold the
shutter button halfway
down to focus
.
AE/AF lock indicator
Flashing indicator
t Indicator lit/beeps
101-0003
Mode
3
BACK/NEXT
.
Movie:
/
button
Program
Auto
Camera
AF range finder frame
Movie:
60min
ISO
STD
B
640
10/10
00:00:03
MENU button
REC
VOLUME
is displayed
• For details on modes, see below.
• The setting is maintained even when the power is turned
off.
60min
2005 1 1 10:30PM
To play back a movie, press z.
WB
Movie:
Press the shutter button
fully down
3/9
Still image: the image size is displayed
Select
(Camera) with b, then
select a mode with v/V.
button
Zoom button
VGA
Program
Auto
Camera
Press the shutter button
fully down
The shutter sounds.
Movie:
Position the subject in the center of the focus
frame.
1
Press MENU.
Still image:
60min
Select
6
View/delete images
Control button
4
Press MENU to turn off the menu.
5
Shoot with the shutter button.
101_0010
STOP
Playback bar
2005 1 1 10:30PM
REV/CUE
VOLUME
Rewind/Fast forward: b/B
(Return to normal playback: z)
Volume: v/V
Stop playback: z
button
Control button
Control button
• Movies with the image size [160] are displayed a size
smaller.
To stop recording, press the shutter button fully down again.
Using the control button
Using the zoom
60min
VGA
96
Using the flash for
still images
Zoom button
60min
To cancel the Scene Selection
To delete images
Select [Auto] or [Program] with v/V.
1 Display the image you want to delete and press
(Delete).
2 Select [Delete] with v, then press z.
60min
S AF
60min
Checking the last
image you shot
(Quick Review)
VGA
Review
101-0029
60min
8/8
2005 1 1 10:30PM
VGA
60min
96
Shooting close-up
(Macro)
S AF
RETURN
60min
VGA
96
Using the
self-timer
To cancel the deletion
• When the zoom scale exceeds 3×, the camera uses the Digital Zoom function.
For details on the [Digital Zoom] settings and the image quality t “User’s Guide/Troubleshooting”
(page 45)
• You cannot change the zoom scale while shooting a movie.
Select [Exit], then press z.
Delete
Exit
BACK/NEXT
S AF
Checking the last still image you shot (Quick Review)
Press b (
) on the control button.
To cancel, press b again.
• The image may appear rough right after playback starts.
• To delete the image, press
(Delete) and select [Delete] with v on the control button, then press z.
Using the self-timer
Before step 2, press V (
Scene Selection modes
) on the control button.
To view an enlarged image (playback zoom)
The following modes are predetermined to match the scene conditions.
Press the shutter button, the self-timer lamp flashes, and a beep sounds until the shutter operates
(approximately 10 seconds later).
Magnifying glass
The subject appears on the LCD
screen magnified by up to 3.5×.
To cancel, press V again.
Self-timer lamp
Distance to the subject
1 cm (13/32 inch)
2 cm (13/16 inch)
5 cm (2 inches)
10 cm (4 inches)
20 cm (7 7/8 inches)
Selecting a flash mode for still images
Before step 2, press v ( ) on the control button repeatedly until the desired mode is selected.
No indicator
Strobes if it is dark (default setting)
• Using a tripod (not supplied) is recommended.
Forced flash
SL
Slow synchro (Forced flash)
The shutter speed is slow in a dark place to clearly shoot the background that is
out of flash light.
No flash
If you shoot a still image of a subject that is difficult to focus on
• If the subject is closer than approx. 50 cm (19 3/4 inches), use the Macro mode (left column).
• When the camera cannot focus on the subject automatically, the AE/AF lock indicator changes to flashing
slowly and the beep does not sound. Recompose the shot and focus again.
• The focal distance to a subject is approx. 1 cm to
20 cm (13/32 inch to 7 7/8 inches).
• The optical zoom is locked to the W side and
cannot be used.
• When you press the zoom button, the image is
enlarged using the digital zoom.
Subjects difficult to focus on are:
• Shooting distance (when [ISO] is set to [Auto])
W side: Approx. 0.1 to 2.5 m (3 15/16 to 8 feet 2 7/16 inches)
T side: Approx. 0.5 to 2.0 m (1 feet 7 11/16 to 6 feet 6 3/4 inches)
• The flash strobes twice. The first time is to adjust the light quantity.
– Distant from the camera and dark
– The contrast between the subject and its
background is poor.
– Seen through glass
– Moving fast
Shooting close-up (Macro)
Before step 2, press B (
Magnification scale
3.5×
2.2×
1.1×
0.5×
0.3×
) on the control button.
To cancel, press B again.
• Setting the zoom all the way to the W side is recommended.
• The in-focus range becomes narrow, and the complete subject may not entirely be in focus.
• The Auto Focus speed drops.
• To shoot at even closer distances than close-ups (Macro) recording, use
(Magnifying glass mode) in the
Scene mode.
Shortest shooting distance from the lens surface
Setting all the way to the W side: Approx. 8 cm (3 1/4 inches)
Setting all the way to the T side: Approx. 25 cm (9 7/8 inches)
– Reflective light or with a lustrous finish
– Flashing
– Backlit
1.1
Shoots portraits of people,
flowers, etc., with a gentle
atmosphere.
Landscape
Shoots landscapes, etc., by
focusing on a distant subject.
High-speed shutter
Shoots night scenes at a distance
without losing the dark
atmosphere of the surroundings.
Shoots portraits in dark places.
Press
while displaying a still image.
To undo the zoom, press
.
Adjust the portion: v/V/b/B
Cancel playback zoom: z
To store enlarged images: [Trimming] t “User’s Guide/Troubleshooting” (page 43)
Viewing an index screen
Press
(Index) and select an image with v/V/b/B.
To return to the single-image screen, press z. To display the next (previous) index screen, press
b/B.
Shoots moving subjects outdoors
or in other bright places.
Beach
Shoots seasides or lakesides, with
the blue of the water clearly
recorded.
Snow
Twilight*
Twilight portrait*
To identify items on the screen
Soft snap
Shoots whitish scenes brightly.
60min
• SINGLE DISPLAY
101-0003
• SINGLE DISPLAY
BACK/NEXT
VGA
3/9
2005 1 1 10:30PM
VOLUME
If you press again, the sixteen-image
index screen appears.
To delete images in index mode
1 While an index screen is displayed, press
control button, then press z.
(Delete) and select [Select] with v/V on the
2 Select the image you want to delete with v/V/b/B, then press z to display the
indicator on the selected image.
(Delete)
Fireworks*
To cancel a selection
Fireworks are recorded in all their
splendor.
Select an image you have previously selected for deletion, then
indicator from the image.
press z to delete the
t “User’s Guide/Troubleshooting” (page 16)
SELECT
TO NEXT
Candle*
Shoot candlelit scenes, without
spoiling the atmosphere.
* The shutter speed becomes slower, so using a tripod is recommended.
To use the functions set by the control button with Scene Selection
Before shooting in step 5, select the settings with the control button. Some functions are not
available, depending on the Scene Selection mode. When you press the button to select functions
that cannot be combined with Scene Selection, a beep sounds. t “User’s Guide/
Troubleshooting” (page 25)
3 Press
(Delete).
4 Select [OK] with B, then press z.
• To delete all the images in the folder, select [All In This Folder] with v/V in step 1 instead of [Select], then
press z.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement