KICKER KIT FOR 2015+ HARLEY DAVIDSON FLTR

KICKER KIT FOR 2015+ HARLEY DAVIDSON FLTR
INSTRUCTION SHEET
KICKER KIT FOR 2015+ HARLEY DAVIDSON FLTR
INCLUDED COMPONENTS:
QUESTIONS?
(2) Custom Wiring Harnesses
(2) 8-32 x 1/2” Button Head Bolts
(2) 8-32 Nylock Nuts
(1) Installation Guide
(1) 6 1/2” Kicker Speakers Pair
(1) Kicker Amp 120W/60W
(4) Black Cable Tie
(1) Stainless Steel Mounting Bracket
EMAIL:
info@getklocked.com
CALL: (605) 996.3700
IMPORTANT INSTALLATION NOTE: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual
for proper procedures and torque specifications. We cannot be responsible for damage resulting from improper installation techniques. This kit may not
be compatible with some aftermarket head units.
PROGRAMMING HD RADIO
NOTE: It is recommended to utilize a motorcycle shop equipped with infotainment programming
software to reflash your radio to recognize your new amplifier.
1
2
3
4
FRONT KIT
REAR KIT
1. Select radio speaker programming menu
2. Select 2 speaker with or without amplifier.
This is a standard EQ flash
3. Select radio and enable amp 1 and send flash
4. Verify each flash was successful and exit programming
1. Select radio speaker programming menu
2. Select 4 speaker system with or without amplifier
3. Select radio and enable amp 1 and send flash
4. Select radio and enable amp 2
5. Verify each flash was successful
GETTING STARTED
1. Remove the seat and disconnect both positive and negative terminals
2. Remove the windshield and outer fairing
a. Once the windshield screws are removed, gently pull off the top vent/cowl piece. There are two
plastic retainer clips that hold it on
b. Remove your stock speaker grilles (1)
> Push them out from the inside of the fairing. They are fastened with a plastic retainer clip
c. Unplug the turn signals (2)
d. Remove the lower T25 fasteners holding the air deflectors to the inner fairing (3)
e. Remove the 3/16” allen bolts holding the turn signals to the inner fairing (4)
f. While holding the fairing, carefully remove the two T30 bolts behind the speaker grilles to remove the outer fairing and set aside (5)
3. Remove the fuel tank
a. Remove the console
b. Unplug the fuel fitting on the left side of the tank
c. Remove all four mounting bolts and carefully lift the tank off the bike and set aside
4. Remove wiring caddy cover
a. Carefully release each tab along the caddy until it lifts completely (6)
K LO C K W E R K S / / W W W. G E T K LO C K E D . C O M
1/2
INSTRUCTION SHEET
SPEAKER INSTALLATION
5. Remove your stock speakers and replace them with your new PSC652 speakers in the kit
a. Install the provided speaker ring adapter onto the speaker pod (8)
b. Install the speaker into the pod and fasten with the original speaker screws (9)
5
6
6
78
9
10
HARNESS INSTALLATION
9. Plug the harness into the amplifier and route speaker wires to their respective connectors (12)
a. Separate the speaker connectors and plug in the amplifier harness to each speaker
10.Plug the switched power harness into the 2-pin amp connector on the right side (13)
11.Plug the blue wire on the kicker harness into the switched power harness lead with one wire
a. This allows for an accessory 12V port to remain available
12.Route both power leads along the left side of the neck and through the electrical caddy to the
seat area.
13.Reconnect the battery terminals
SYSTEM SETUP
Note: At this time, it is highly recommended to set the amp gain to 0. Klock Werks recommends
that the dip switches be set up as follows: 1. Auto turn-on - 12V
2. Input level - HI
3. HI-PASS – 80 Hz
4. Input Gain control – 0
14.Plug the radio in, but do not reinstall it until the gain has been set
15.Test component function and set the gain to optimize system performance.
16.Carefully reassemble the motorcycle and enjoy your new audio kit!
Note: These two leads are amplified and non-amplified speaker outs with auxiliary switched power.
They are intended to provide ease of installation for speaker lid speakers or other add-on audio.
(14)
12
12
13
13
14
CAUTION: Klock Werks cannot be held responsible for any damage to painted surfaces during removal or addition of Klock Werks parts.
K LO C K W E R K S / / W W W. G E T K LO C K E D . C O M
2/2
4405-HDFLTR1501R1 ©2016 KLOCK WERKS
11
11
AMP INSTALLATION
6. Remove the radio
a. Unplug the four connectors on the back of the radio
b. Remove the four allen head bolts holding the radio to the chassis
c. Gently remove the radio from the chassis
7. Install the PXA200.2 amplifier onto bracket with supplied hardware
a. Slide the end of the amplifier with the connector port into the bracket and fasten with
supplied hardware (10)
b. Install the bolts from the bottom and fasten the locknuts onto the amplifier
8. Carefully install bracket/amplifier assembly onto radio chassis by installing the assembly
through the radio face port in the fairing and sliding the tabs of the bracket over the chassis (11)
a. The amp bracket assembly mounts under the radio
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising