User manual
Always there to help you
Register your product and get support at
www.philips.com/support
NTX400
Question?
Contact
Philips
User manual
Contents
1Important
2
Safety2
2 Your Mini Hi-Fi System
4
Introduction4
What's in the box
4
Overview of the main unit
5
Overview of the remote control
6
3 Get started
8
Connect8
Prepare the remote control
8
Connect power
9
Set clock
9
Turn on
9
4 Play from a disc or USB
Play a disc
Play from a USB storage device
Control play
Program tracks
View play information
10
10
10
10
11
11
5 Play audio through Bluetooth
12
12
12
13
6 Listen to radio
14
14
14
14
15
Connect a device
Play from Bluetooth device
Disconnect a device
Store radio stations automatically
Tune to a radio station
Store radio stations manually
Select a preset radio station
7 Adjust sound
16
16
16
16
16
16
8 Other features
17
17
17
18
18
19
19
Adjust volume
Mute sound
Select a preset sound effect
Enhance bass
Apply NX Bass effect
Listen to an external device
Record to a USB device
Set the timer
Set sleep timer
Turn decorative light on or off
Listen through a headphone
9 Product information
20
Specifications
20
USB playability information
21
Supported MP3 disc formats
21
Maintenance21
10Troubleshooting
22
22
About Bluetooth device
11Notice
23
Disposal of your old product23
Trademark notice
23
EN
1
1Important
•
•
Safety
•
Know these safety symbols
This 'bolt of lightning' indicates uninsulated
material within your unit may cause an electrical
shock. For the safety of everyone in your
household, please do not remove product
covering.
The 'exclamation point' calls attention to
features for which you should read the enclosed
literature closely to prevent operating and
maintenance problems.
WARNING: To reduce the risk of fire or electric
shock, this apparatus should not be exposed to
rain or moisture and objects filled with liquids,
such as vases, should not be placed on this
apparatus.
CAUTION: To prevent electric shock, match
wide blade of plug to wide slot, fully insert.
Warning
•
•
•
•
•• Never remove the casing of this device.
•• Never lubricate any part of this device.
•• Never place this device on other electrical equipment.
•• Keep this device away from direct sunlight, naked
flames or heat.
•• Never look into the laser beam inside this device.
•• Ensure that you always have easy access to the power
cord, plug, or adaptor to disconnect this device from
the power.
•
•
Do not use this apparatus near water.
Install in accordance with the
manufacturer's instructions.
2
EN
•
Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories specified
by the manufacturer.
Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning
storms or when unused for long periods
of time.
Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
remote control:
• Install the battery correctly, + and - as
marked on the remote control.
• Do not mix batteries (old and new or
carbon and alkaline, etc.).
• Remove the battery when the remote
control is not used for a long time.
The battery shall not be exposed to
excessive heat such as sunshine, fire or the
like.
•
•
•
Apparatus shall not be exposed to
dripping or splashing.
Do not place any sources of danger on the
apparatus (e.g. liquid filled objects, lighted
candles).
Where the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Caution
•• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
laser exposure or other unsafe operation.
Hearing safety
Listen for reasonable periods of time:
• Prolonged exposure to sound, even
at normally 'safe' levels, can also cause
hearing loss.
• Be sure to use your equipment reasonably
and take appropriate breaks.
Be sure to observe the following guidelines
when using your headphones.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume as your
hearing adapts.
• Do not turn up the volume so high that
you can't hear what's around you.
• You should use caution or temporarily
discontinue use in potentially hazardous
situations.
Note
•• The type plate is located on the back of the unit.
Listen at a moderate volume.
• Using headphones at a high volume can
impair your hearing. This product can
produce sounds in decibel ranges that may
cause hearing loss for a normal person,
even for exposure less than a minute. The
higher decibel ranges are offered for those
that may have already experienced some
hearing loss.
• Sound can be deceiving. Over time your
hearing 'comfort level' adapts to higher
volumes of sound. So after prolonged
listening, what sounds 'normal' can actually
be loud and harmful to your hearing. To
guard against this, set your volume to a safe
level before your hearing adapts and leave
it there.
To establish a safe volume level:
• Set your volume control at a low setting.
• Slowly increase the sound until you can
hear it comfortably and clearly, without
distortion.
EN
3
2 Your Mini Hi-Fi
System
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.Philips.com/welcome.
Introduction
With this product, you can
• enjoy audio from discs, USB storage
devices, Bluetooth enabled devices, or
other external devices;
• listen to FM and AM radio stations; and
• record from a disc to a USB storage
device.
To enrich sound, this product offers you these
sound effects:
• Preset Equalizer (EQ) Settings
• Dynamic Bass Boost (DBB)
• NX Bass Enhancement
What's in the box
Check and identify the contents of your
package:
• Main unit x 1
• Remote control (with one AAA battery)
• FM wire antenna x 1
• AM loop antenna x 1
• Shoulder strap x 1
• Short user manual
4
EN
Overview of the main unit
p
o
n
m
l
k
q
j
r
s
i
a b c de
a
b
f
g
c
• Turn on the product.
• Switch to standby or Eco power
standby mode.
/
• In Disc or USB mode, skip to the
previous or next album.
• In FM or AM tuner mode, select a
preset radio station.
• In standby mode, adjust hour and
minute during clock/timer setting.
d
h
/OK
• Pause or resume play.
• Confirm a selection.
• In AM tuner mode, change AM tuning
grid.
• Stop play or erase programmed list.
• Exit clock/timer setting mode.
• Exit the recording process.
EN
5
e
/
• In tuner mode, tune to radio stations.
• In DISC or USB mode, skip to the
previous or next track.
• In DISC or USB mode, search within
a track.
f NX BASS
• Turn bass effect on.
g Volume knob
• Adjust volume.
h
• Enable or diable the speaker lighting
effect.
i NFC
• Connect a NFC compatible device
through Bluetooth.
j AUDIO IN
• Connect an external audio device.
k Display panel
• Show current status.
l EJECT
• Open or close the disc tray.
m DBB
• Turn dynamic bass enhancement on
or off.
Overview of the remote
control
a
b
c
d
e
f
g
h
p SOURCE
• Select an audio source.
q
• Connect a headphone.
r USB socket
• Connect a USB mass storage device.
s REC
• Record to a USB device.
6
EN
q
i
j
p
o
n
m
k
l
a
n MODE
• Select a repeat or shuffle play mode.
o EQ
• Select a preset equalizer (EQ) setting.
r
b
• Turn on the product.
• Switch to standby or Eco power
standby mode.
• Open or close the disc tray.
c SOURCE
• Select an audio source.
d MODE
• Select a repeat or shuffle play mode.
e
/
• In Disc or USB mode, skip to the
previous or next album.
• In FM or AM tuner mode, select a
preset radio station.
• In standby mode, adjust hour and
minute during clock/timer setting.
f
g
h
i
/
• In FM or AM tuner mode, tune to
radio stations.
• In DISC or USB mode, skip to the
previous or next track.
• In DISC or USB mode, search within
a track.
• Pause or resume play.
• Confirm a selection.
• In AM tuner mode, change AM tuning
grid.
• Mute or resume sound.
• Stop play or erase programmed list.
• Exit clock/timer setting mode.
• Exit the recording process.
j USB REC
• Record to a USB device.
k CLOCK
• Set clock.
l EQ
• Select a preset equalizer (EQ) setting.
m DBB
• Turn dynamic bass enhancement on
or off.
n LIGHT
• Enable or diable the speaker lighting
effect.
o TIMER
• Set the timer.
p SLEEP
• Set sleep timer.
q + VOL • Adjust volume.
r PROG
• Program tracks.
• Program radio stations.
EN
7
3 Get started
Connect AM antenna
Note
Caution
•• For better reception, adjust the position of the AM
antenna.
•• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
laser exposure or other unsafe operation.
1
Assemble the AM loop antenna.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of this apparatus. The
model number and serial number are on the
back of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Connect
Connect FM antenna
2
Connect the AM loop antenna to the AM
jack on the back of the main unit.
Note
•• For better reception, fully extend and adjust the
position of the FM antenna.
Connect the supplied FM antenna to the FM
jack on the back of the main unit.
Prepare the remote control
Note
•• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
•• Batteries contain chemical substances, so they should
be disposed of properly.
1
2
8
EN
Open the battery compartment.
Insert one AAA battery with correct
polarity (+/-) as indicated.
Set clock
1
3
Close the battery compartment.
Connect power
Caution
•• Risk of product damage! Make sure that the power
supply voltage corresponds to the voltage printed on
the back or the underside of the product.
•• Risk of electric shock! When you unplug the power
cord, always pull the plug from the socket. Never pull
the cord.
Note
•• Before connecting to AC power, make sure that you
have completed all other connections.
1
Adjust the voltage selector on the back of
the main unit to match your local power
supply.
2
3
4
In standby mode, press and hold CLOCK
for two seconds.
»» [CLOCK SET] appears, then [12H] or
[24H] is displayed.
Press / repeatedly to select 12 hour
or 24 hour format.
Press CLOCK to confirm.
»» The hour digit flashes.
Repeat steps 2 to 3 to set the hour and
minute.
Note
•• To cancel clock setting, press .
•• During clock setting, if no action is taken within 90 seconds,
the product exits clock setting mode automatically.
•• The clock is displayed in standby mode. To view the
clock in working or ECO power standby mode, press
and hold CLOCK for two seconds.
Turn on
Press .
»» The product switches to the last
selected source.
Switch to standby mode
2
Connect the AC power plug to the power
outlet.
Press again to switch the product to standby
mode.
»» The clock (if set) is displayed.
To switch between standby mode and Eco
power standby mode:
Press and hold for two seconds.
»» In Eco power standby mode, the
button lights up red, and the display
backlight is off.
Tip
•• The product switches to Eco power standby mode
automatically after 10 minutes in standby mode.
EN
9
4 Play from a disc
or USB
2
Insert the USB plug of the device into the
socket.
Play a disc
Note
•• Make sure that the disc contains playable audio
contents.
1
2
3
Press SOURCE repeatedly to select the
disc source.
Press
to open the disc tray.
Insert a disc into the disc tray, with the
printed side facing up.
DISC
3
4
Press
Control play
In DISC or USB mode, follow the instructions
below to control play.
/
Press again to close the disc tray.
»» Play starts automatically.
Play from a USB storage
device
Note
•• Make sure that the USB device contains playable audio
contents in supported formats.
1
10
Press SOURCE repeatedly to select the
USB source.
EN
to select a folder.
Press
/
to select an audio file.
»» Play starts automatically.
Button
/
4
/
MODE
Action
Press to skip to the previous or next
track.
Press and hold to fast forward or fast
reverse the track during playback,
then release to resume play.
Press to select an album.
Press to pause or resume play.
Press to stop play.
Press repeatedly to select a play
mode:
• [OFF]: return to normal play mode.
• [REPEAT ONE]: play the current
track repeatedly.
• [REPEAT ALL]: play all tracks
repeatedly.
• [SHUFFLE]: play all tracks randomly.
Note
•• Random play cannot be selected when you play the
programmed tracks.
Program tracks
You can program a maximum of 20 tracks.
1
2
3
4
5
6
In DISC or USB mode, press
playing.
to stop
Press PROG to activate the program
mode.
»» A number flashes on the screen.
For MP3 tracks, press
album.
or
to select an
Press
or
to select a track number,
then press PROG to confirm selection.
Repeat steps 3 to 4 to program other
tracks.
Press
to play the programmed track.
• To erase the program, press twice.
View play information
Note
•• You can only view the play information in DISC or USB
mode.
During play, press CLOCK repeatedly to view
different play information (if available):
• Track number and play time
• Title
• Artist
• Album
EN
11
5 Play audio
through
Bluetooth
The product can stream music from your
Bluetooth device to the system through
Bluetooth.
3
4
Connect a device
Note
•• Before pairing a device with this product, read its user
manual for Bluetooth compatibility.
•• The product can memorize a maximum of eight paired
devices. The ninth paired device will replace the first
one.
•• Any obstacle between this product and a Bluetooth
device can reduce the operational range. Keep away
from any other electronic device that may cause
interference.
•• The operational range between this product and a
Bluetooth device is approximately 10 meters (30 feet).
Near Field Communication (NFC) is a
technology that enables short-range wireless
communication between various NFC
compatible devices, such as mobile phones and
IC tags.
If your Bluetooth device supports NFC, you can
connect it with this product easily.
1
2
12
Enable the NFC feature on your Bluetooth
device (refer to its user manual).
Tap the NFC tag on the top of the product
with the NFC area of your Bluetooth
device until you hear a beep.
EN
Follow the on-screen instructions to
complete the pairing and connection.
»» After successful connection, [BT
CONNECTED] (BT connected)
scrolls on the screen, and the product
beeps twice.
Option 2: Connect a device manually
1
2
3
Option 1: Connect a device through
NFC
On your Bluetooth device, accept the
pairing request with "Philips NX4".
Press SOURCE repeatedly to select [BT]
source.
On your Bluetooth device, enable
Bluetooth and search for Bluetooth devices
that can be paired (see the user manual of
the device).
Select [Philips NX4] displayed on your
device for pairing.
»» After successful connection, [BT
connected] (BT connected) scrolls
on the screen, and the product beeps
twice.
Play from Bluetooth device
After successful Bluetooth connection, play
audio on the Bluetooth device.
»» Audio streams from your Bluetooth
device to this product.
Disconnect a device
•
•
•
Press and hold
for three seconds;
Disable Bluetooth on your device; or
Move the device beyond the
communication range.
»» The product beeps twice.
Note
•• Before connecting another Bluetooth device, disconnect
the current device first.
EN
13
6 Listen to radio
•
You can also press and hold PROG
for two seconds to activate automatic
programming.
»» [AUTO] (auto) is displayed.
»» The product stores radio stations with
sufficient signal strength automatically.
Store radio stations
automatically
»» The first stored radio station is
broadcast automatically.
Note
•• You can program a maximum of 20 FM and 10 AM
radio stations.
•
1
2
When entering FM or AM mode for the first
time, the product prompts you to search and
store all the available radio stations.
Press SOURCE repeatedly to select FM or
AM tuner mode.
»» [AUTO INSTALL-PRESS PLAY-STOP
CANCEL] (auto install-press play-stop
cancel) is displayed.
Press
to start full scan.
»» [AUTO] is displayed.
»» The product stores all the available
radio stations automatically, and then
broadcasts the first available station.
Tune to a radio station
Tip
•• Keep the product away from other electronic devices
to avoid radio interference.
•• For better reception, fully extend and adjust the
position of the antenna.
1
2
3
»» The station list is memorized in the
product. When you enter the radio
mode next time, the station scan does
not take place.
Note
Press and hold
/
for two seconds.
»» [SEARCH] is displayed.
»» The radio tunes to a station with
strong signal automatically .
Repeat step 2 to tune to more stations.
• To tune to a station with weak signal,
press
/
repeatedly until you find
better reception.
Store radio stations manually
•• If you press , the product will not perform full scan,
and the same message will pop up when you enters FM
or AM mode next time.
Press SOURCE repeatedly to select FM or
AM tuner.
Note
•• You can program a maximum of 20 FM and 10 AM
radio stations.
1
2
14
EN
Tune to a radio station.
Press PROG to activate the program
mode.
»» A position number is displayed.
3
4
Press / to allocate a number to this
radio station, then press PROG to confirm.
Repeat steps 1 to 3 to program other
stations.
Tip
•• To overwrite a programmed station, store another
station in its place.
Select a preset radio station
In tuner mode, press
number.
/
to select a preset
EN
15
7 Adjust sound
Adjust volume
During play, press + VOL - to increase or
decrease volume.
Mute sound
During play, press
to mute or resume sound.
Select a preset sound effect
During play, press EQ repeatedly to select
special sound effects:
• [PARTY] (party)
• [ROCK] (rock)
• [REGUETON] (regueton)
• [HIP-HOP] (hip-hop)
• [POP] (pop)
Apply NX Bass effect
NX Bass effect adds clean and lively
characteristics to your music with rather low
background noise.
• During play, press NX BASS. The sound will
change in 3 stages:
• Stage 1: The sound volume increases to
a higher level and stays at this level for
5 seconds.
»» [FIRING] (firing) is displayed.
• Stage 2: The sound volume gradually
decreases to its original level in 10
seconds.
»» [DISCHARGING] (discharging) is
displayed.
• Stage 3: The sound volume keeps at
normal level for 40 seconds.
»» [RECHARGING] (recharging) is
displayed.
Note
•• To reactivate the NX bass effect, press NX BASS again
after the 3 stages are completed.
Enhance bass
The best Dynamic Bass Enhancement (DBB)
setting is generated automatically for each
EQ selection. You can manually select the
DBB setting that best suits your listening
environment.
• During play, press DBB repeatedly to
select:
• DBB 1
• DBB 2
• DBB 3
• DBB OFF
16
EN
8 Other features
2
Listen to an external device
3
With this product, you can listen to an external
audio device such as an MP3 player.
Connect the white and red audio cables
(not supplied) to:
• the AUX IN sockets on the back of
the product.
• the AUDIO OUT socket on a TV or
DVD player.
Play audio on the external audio device
(refer to the user manual of the device).
AUX DVD
AUX TV
Play from an MP3 player
1
2
3
L
Press SOURCE repeatedly to select the
AUDIO IN source.
Connect an audio input cable (not
supplied) with a 3.5 mm connector on
both ends to:
• the AUDIO IN socket on the product,
and
• the headphone socket on the MP3
player.
Play audio on the MP3 player (refer to its
user manual).
AUDIO IN
Record to a USB device
Audio CD tracks and MP3 files are recorded in
.mp3 format.
The first time you record to a USB device,
a folder is automatically created in the USB
device. Each time you record to a USB device,
the recorded files are stored in a sub-folder.
Files and subfolders are named numerically in
the order by which they are created.
1
2
Play from other audio device
You can also play audio from a TV or DVD
player.
1
Press SOURCE repeatedly to select AUX
DVD or AUX TV source.
DVD
R
Plug a USB device into the
socket.
Select the disc source and load a disc.
• To record one track in a disc: select a
track to play, then press USB REC.
• To record all tracks in a disc: press to
stop play, then press USB REC.
»» Play starts automatically from the
beginning of the disc or the selected
track, and the recording starts.
• To stop recording, press .
EN
17
Note
Note
•• If the USB device does not have enough memory to
store the audio files, a message about a full memory is
displayed.
•• With MP3-CD playback, you can only record all tracks
in the current folder.
Set the timer
If a timer is set, the product will be turned on
automatically after a preset time.
•• To cancel timer setting, press .
•• During timer setting, if no action is taken within
90 seconds, the product exits timer setting mode
automatically.
Activate or deactivate the timer
•
In standby mode, press TIMER repeatedly
to activate or deactivate the timer.
»» If the alarm timer is activated, [TIMER
ON] is displayed.
»» If the alarm timer is deactivated,
[TIMER OFF] is displayed.
Note
•• Make sure that clock is set correctly.
1
2
3
4
5
6
18
In standby mode, press and hold TIMER
for two seconds.
»» [TIMER SET] is displayed, then a
prompt to select the sound source is
displayed.
Press / repeatedly to select a sound
source: DISC, USB, FM, or AM.
Press TIMER to confirm.
»» [12H] or [24H] is displayed.
Press /
format.
to select 12 hour or 24 hour
Press TIMER to confirm.
»» In 12 hour format, [AM] or [PM] is
displayed. Repeat steps 4 to 5 to select
AM or PM. Then the hour digits begin
to flash.
»» In 24 hour format, the hour digits begin
to flash.
Repeat steps 4 to 5 to set the hour,
minute, and the volume of the sound
source.
»» If the product is in standby or Eco
power standby mode, the selected
sound source will be activated when
the preset time comes.
EN
Set sleep timer
When the product is turned on, press SLEEP
repeatedly to select a period of time (in
minutes).
»» The product switches to standby
mode automatically after the preset
time period.
»» When [SLEEP OFF] (sleep off)
is displayed, the sleep timer is
deactivated.
Turn decorative light on or
off
In power-on mode, press LIGHT repeatedly to
select a speaker light color or turn the light off:
• [PEACE] (peace)
• [POWERFUL] (peace)
• [PASSION] (passion)
• [SAMBA] (samba)
• [FIESTA] (fiesta)
• [CIELO] (cielo)
• [CUSTOM] (custom)
• [OFF] (off)
Listen through a headphone
Plug a headphone into the
product.
socket on the
Use the shoulder strap
A shoulder strap is provided for carrying this
product. Follow the illustration to attach the
shoulder strap to each end of the product.
•
EN
19
9Product
information
•• Product information is subject to change without prior
notice.
Specifications
Amplifier
Total Output Power
1000W RMS (THD
30%)
60 -20000 Hz, ±3 dB
≥70 dBA
1V/2V RMS Rin
≥22kΩ
Frequency Response
Signal to Noise Ratio
Audio/AUX Input
Laser Type
Disc Diameter
Support Disc
Audio DAC
Total Harmonic
Distortion
Frequency Response
Semiconductor
12cm/8cm
CD-DA, CD-R, CDRW, MP3-CD
24 Bits / 44.1 kHz
<1% (1 kHz)
60 Hz - 20 kHz (44.1
kHz)
≥70 dBA
Speakers
20
EN
-Mono, 26dB S/N
Ratio
Search Selectivity
Total Harmonic
Distortion
Signal to Noise Ratio
Number of Presets
FM: 87.5 - 108MHz;
AM: 531 - 1602kHz
(9KHz);
50kHz (FM), 9KHz
(AM)
<22 dBf
<35 dBf
<2%
>50 dB
20 FM, 10 AM
Bluetooth
Bluetooth Version
Bluetooth Frequency
Band
Bluetooth Profile
Range
V4.0 + EDR
2.402GHz ~ 2.48GHz
ISM Band
A2DP, AVRCP V1.4
10 m (Free space)
General information
Disc
Speaker
Impedance
Speaker Driver
Sensitivity
Tuning Range
Tuning Grid
Note
S/N Ratio
Tuner
3 ohm
6.5" Woofer, 2" Tweeter
Woofer: 87± 3dB/m/W;
Tweeter: 88± 3dB/m/W
AC Power
Operation Power
Consumption
Standby Power
Consumption
Eco Power Standby
Consumption
USB Direct
Headphone Output
Operating Temperature
and Humidity
Dimensions - Main
Unit (W x H x D)
Weight - Main Unit
230-240 V~, 50 Hz
170 W
30 W
< 1W
Version 2.0HS, 5V 1A
5.0mW 2x 16Ω
0°C to 45°C, 5% to
90% humidity for all
climates
287 x 818 x 303 mm
13 kg
USB playability information
Maintenance
Compatible USB devices:
• USB flash memory (USB 2.0)
• USB flash players (USB 2.0)
• memory cards (requires an additional
card reader to work with this unit)
Supported formats:
• USB or memory file format FAT12,
FAT16, FAT32 (sector size: 512 bytes)
• MP3 bit rate (data rate): 32-320 Kbps
and variable bit rate
• Directory nesting up to a maximum of
8 levels
• Number of albums/ folders: maximum
99
• Number of tracks/titles: maximum 999
• ID3 tag v1.2 or later
• File name in Unicode UTF8 (maximum
length: 128 bytes)
Unsupported formats:
• Empty albums: an empty album is an
album that does not contain MP3 files,
and is not be shown in the display.
• Unsupported file formats are skipped.
For example, Word documents (.doc)
or MP3 files with extension .dlf are
ignored and not played.
• AAC, WAV, PCM audio files
• WMA files
Clean the cabinet
• Use a soft cloth slightly moistened with
a mild detergent solution. Do not use a
solution containing alcohol, spirits, ammonia
or abrasives.
Clean discs
• When a disc becomes dirty, clean it with
a cleaning cloth. Wipe the disc from the
centre out.
•
Do not use solvents such as benzene,
thinner, commercially available cleaners,
or antistatic spray intended for analogue
records.
Clean the disc lens
• After prolonged use, dirt or dust may
accumulate at the disc lens. To ensure good
play quality, clean the disc lens with Philips
CD lens cleaner or any commercially
available cleaner. Follow the instructions
supplied with cleaner.
Supported MP3 disc formats
•
•
•
•
•
•
•
ISO9660, Joliet
Maximum title number: 999 (depending on
file name length)
Maximum album number: 99
Supported sampling frequencies: 32 kHz,
44.1kHz, 48 kHz
Supported Bit-rates: 32-320 (kbps),
variable bit rates
ID3 tag v1.2 or later
Directory nesting up to a maximum of 8
levels
EN
21
10Troubleshooting
Caution
•• Never remove the casing of this unit.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this unit,
check the following points before requesting
service. If the problem remains unsolved, go to
the Philips web site (www.philips.com/support).
When you contact Philips, ensure that your
unit is nearby and the model number and serial
number are available.
No power
•• Make sure that the AC power plug of the
unit is connected properly.
•• Make sure that there is power at the AC
outlet.
•• To save power, the unit switches to
standby automatically 10 minutes after
a play reaches the end and no control is
operated.
No sound or poor sound
•• Adjust the volume.
•• Check if the product is muted. If yes, press
to resume sound.
No response from the unit
•• Disconnect and reconnect the AC power
plug, then turn on the unit again.
Remote control does not work
•• Before you press any function button, first
select the correct source with the remote
control instead of the main unit.
•• Reduce the distance between the remote
control and the unit.
•• Insert the batteries with their polarities
(+/– signs) aligned as indicated.
•• Replace the batteries.
•• Aim the remote control directly at the
sensor on the front of the main unit.
No disc detected
•• Insert a disc.
•• Check if the disc is inserted upside down.
22
EN
••
Wait until the moisture condensation at
the lens has cleared.
•• Replace or clean the disc.
•• Use a finalized CD or correct format disc.
Cannot display some files in USB device
•• The number of folders or files in the USB
device has exceeded a certain limit. This
phenomenon is not a malfunction.
•• The formats of these files are not
supported.
USB device not supported
•• The USB device is incompatible with the
unit. Try another one.
Poor radio reception
•• Increase the distance between the unit and
other electrical appliances.
•• Adjust the position of the antenna for
better reception.
About Bluetooth device
The audio quality is poor after connection
with a Bluetooth-enabled device.
•• The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
Cannot connect with the device.
•• The Bluetooth function of the device is not
enabled. Refer to the user manual of the
device for how to enable the function.
•• This product is already connected with
another Bluetooth-enabled device.
Disconnect that device and then try again.
The paired device connects and disconnects
constantly.
•• The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
•• For some devices, Bluetooth connection
may be deactivated automatically as a
power-saving feature. This does not indicate
any malfunction of this product.
11Notice
Any changes or modifications made to this
device that are not expressly approved by
Gibson Innovations may void the user’s
authority to operate the equipment.
Disposal of your old product
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Do not throw away the product with the
normal household waste at the end of its life,
but hand it in at an official collection point or
recycling. By doing this, you help to preserve the
environment.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Trademark notice
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Gibson
Innovations Limited is under license. Other
trademarks and trade names are those of their
respective owners.
The N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the United
States and in other countries.
This is CLASS II apparatus with double
insulation, and no protective earth provided.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.
Specifications are subject to change without
notice. Gibson reserves the right to change
products at any time without being obliged to
adjust earlier supplies accordingly.
EN
23
Specifications are subject to change without notice.
2015 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and
Gibson Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used
under license from Koninklijke Philips N.V.
NTX400_79_UM_V1.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising