10 WAX BUFFER - Grizzly Industrial

10 WAX BUFFER - Grizzly Industrial
10" WAX BUFFER
MODEL H3143
INSTRUCTION MANUAL
COPYRIGHT © OCTOBER 2002 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN CHINA
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE
AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS
PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF
THE MACHINE, THIS MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE. CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT DIFFERENCES. PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
•
•
•
Lead from lead-based paints.
Crystalline silica from bricks, cement, and
other masonry products.
Arsenic and chromium from chemically
treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter out microscopic particles.
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are
intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
NOTICE
This symbol is used to alert the user to useful information
about proper operation of the equipment.
Safety Instructions
1.
KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2.
REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to see that keys and adjusting
wrenches are removed from winch
before operation.
3.
KEEP CHILDREN AWAY. All children should be kept at a safe distance from winch.
4.
DO NOT USE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL.
5.
NEVER ALLOW UNTRAINED
USERS TO RUN THIS TOOL
WHILE UNSUPERVISED.
H3143 Wax Buffer
6.
WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets, or other
jewelry which may get caught in
moving parts. Non-slip footwear is
recommended. Wear protective
hair covering to contain long hair.
7.
ALWAYS USE SAFETY GLASSES. Also use face or dust mask if
cutting operation is dusty. Everyday
eyeglasses only have impact resistant lenses, they are NOT safety
glasses.
8.
IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING THE TOOL.
-1-
Safety Instructions For Power Tools
9.
USE PROPER EXTENSION CORD
for the tool. Make sure your extension cord is in good condition.
Conductor size should be in accordance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged.
Minimum Gauge for Extension Cords
AMP
LENGTH
RATING
25ft
50ft
100ft
0-6
18
16
16
7-10
18
16
14
11-12
16
16
14
13-16
14
12
12
17-20
12
12
10
21-30
10
10
No
10. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving
parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a
vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.
13. DON’T OVERREACH. Keep proper
footing and balance at all times.
-2-
14. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for
best and safest performance.
Follow instructions for lubricating
and changing accessories.
15. DISCONNECT TOOLS before servicing and changing accessories,
such as blades, bits, cutters, and
the like.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make
sure switch is in off position before
plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult the owner’s
manual for recommended accessories. The use of improper accessories may cause risk of injury.
18. CHECK DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is damaged should be carefully checked
to determine that it will operate
properly and perform its intended
function. Check for alignment of
moving parts, binding of moving
parts, breakage of parts, mounting, and any other conditions that
may affect its operation. A guard or
other part that is damaged should
be properly repaired or replaced.
No list of safety guidelines can be
complete. Operating this tool may
require additional safety precautions specific to your working
environment. Failure to use reasonable caution while operating
this tool could result in serious
personal injury.
H3143 Wax Buffer
INTRODUCTION
Commentary
The specifications, details, and photographs in this manual represent the
Model H3143 as supplied when the manual was prepared. However, owing to
Grizzly’s policy of continuous improvement, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
Grizzly Industrial, Inc.
/O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
C
Lack of familiarity with this manual
could cause serious personal injury.
Become familiar with the contents of
this manual, including all the safety
warnings.
We are proud to offer the Grizzly Model
H3143 Wax Buffer. This model is part of a
growing Grizzly family of fine tools. When
used according to the guidelines set forth
in this manual, you can expect years of
trouble-free, enjoyable operation and
proof of Grizzly’s commitment to customer
satisfaction.
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: techsupport@grizzly.com
Web Site: http://www.grizzly.com
We are pleased to provide this manual
with the Model H3143. It was written to
encourage safety considerations and
guide you through general operating procedures and maintenance. This manual
represents our effort to produce the best
documentation possible.
H3143 Wax Buffer
-3-
OPERATION
About Your New Buffer
Always follow the manufacturer’s
instructions when applying wax.
Failure to follow the instructions
could result in damage to the surface
you are waxing.
Please take the time to become familiar
with this instruction manual. The information contained will allow you to get the
maximum enjoyment and use from your
new tool.
5. Buff in a back and forth pattern, allowing the buffer to glide over the work surface. DO NOT exert excessive pressure on the buffer!
6. Buff hard-to-reach areas by hand.
7. Once applied, allow the wax to form a
haze on the work surface.
8. Replace the terry cloth bonnet with the
synthetic wool cap.
9. Buff the waxed surface in the same
manner it was applied. DO NOT exert
excessive pressure on the buffer!
Accessories
Included with the Model H3143 Wax Buffer
are two bonnets: the terry cloth bonnet is
used to wax and the synthetic wool bonnet
is used to buff the wax.
Using The Buffer
Never use abrasive wax or polish
when using this tool. Damage to the
paint may occur.
1. Evenly apply wax to the terry cloth bonnet. DO NOT apply the wax directly to
the work surface.
2. WITHOUT turning the buffer on, set it
on the work surface.
3. Place the power cord over your shoulder to keep it off the work surface.
4. Turn the buffer on and begin buffing a
large flat area such as the hood.
-4-
H3143 Wax Buffer
MAINTENANCE
Replacement Parts
REF PART #
Unplug the tool from the power
source before performing any maintenance! Failure to follow this warning could result in serious personal
injury.
DESCRIPTION
01 PH3143001 MOTOR BRUSH (2)
02` PH3143002 BODY TOP HALF
03 PH3143003 BODY LOWER HALF
04 PH3143004 TERRYCLOTH CAP
05 PH3143005 SYNTHETIC CAP
Cleaning The Buffer
• Use only a mild soap to clean the bonnets.
• Wash the bonnets by hand and hang
dry.
• When not in use, remove the bonnets
and store the buffer with the pad facing
up. This allows the pad to retain its original form.
• Periodically clean the buffer with a dry
cotton cloth. DO NOT use flammable
products or spray cleaners.
06 PH3143006 SWITCH
07 PH3143007 SWITCH SLIDER
08 PHTEK13
TAP SCREW #8 X 11⁄16"
09 PH3143009 MOTOR ASSEMBLY
Carbon Motor Brushes
The Model H3143 has a brush-type electric
motor. Because the buffer needs to be disassembled to gain access to the brushes,
servicing them should only be performed
by a qualified technician.
Repairs
The Model H3143 is a double insulated
and UL® listed tool which should only be
repaired by a qualified technician. DO NOT
attempt to open the tool housing or perform any electrical repairs. Contact our
Customer Service Department if the tool
stops working or malfunctions.
H3143 Wax Buffer
Gasoline or petroleum products used
to clean the tool could explode causing serious personal injury. DO NOT
use gasoline or petroleum products
to clean the tool.
-5-
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
techsupport@grizzly.com
Web Site: http://www.grizzly.com
Thank you again for your business and continued support. We hope to serve you again
soon!
-6-
H3143 Wax Buffer
WARRANTY CARD
Name __________________________________________________________
Street __________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
Model #___________________________ Serial #______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___Card Deck
___World Wide Web
___Other__________________________
2. What is your annual household income?
___$20,000-$29,999
___$60,000-$69,999
___$30,000-$39,999
___$70,000-$79,999
___$40,000-$49,999
___$80,000-$89,999
___$50,000-$59,999
___$90,000 +
3. What is your age group?
___20-29
___50-59
___30-39
___60-69
___40-49
___70 +
4. How long have you been a woodworker?
___0 - 2 Years
___8 - 20 Years
___2 - 8 Years
___20+ Years
5. How would you rank your woodworking skills?
___Simple
___Advanced
___Intermediate
___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
___Air Compressor
___Panel Saw
___Band Saw
___Planer
___Drill Press
___Power Feeder
___Drum Sander
___Radial Arm Saw
___Dust Collector
___Shaper
___Spindle Sander
___Jointer
___Table Saw
___Lathe
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Other______________________________
7. How many of your woodworking machines are
Grizzly? _____________
8. Which benchtop tools do you own? Check all
that apply.
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___8" Table Saw
___8" - 10" Bandsaw
___Scroll Saw
___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___Other______________________________
9. How many of the machines checked above are
Grizzly? ____________
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Orbital Sander
___Biscuit Joiner
___Palm Sander
___Circular Saw
___Portable Planer
___Detail Sander
___Saber Saw
___Drill/Driver
___Reciprocating Saw
___Miter Saw
___Router
___Other_________________________________
11. What machines/supplies would you like Grizzly
Industrial to carry?
________________________________________
________________________________________
________________________________________
________________________________________
12. What new accessories would you like Grizzly
Industrial to carry?
________________________________________
________________________________________
________________________________________
________________________________________
13. What other companies do you purchase your tools
and supplies from?
_________________________________________
_________________________________________
_________________________________________
14. Do you think your purchase represents good value?
___Yes
___No
15. Would you recommend Grizzly to a friend?
___Yes
___No
16. Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We
never use names more than three times.
___Yes
___No
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT NAIL
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising