Premis Kwikset ENG printable.indd

Premis Kwikset ENG printable.indd
Installation and
User Guide
ENGLISH
66070 / 01
Required tools
Parts in the box
Ruler
Latch with
rectangular faceplate
Drive-in latch
Strike
Exterior
assembly
Adapter ring
Keys
Phillips screwdriver
A
Additional tools
(depending on application)
Hammer
B
Mounting plate
Interior assembly
G
N
Q
03809
Interior cover
J
Strike screws
P
D
Battery pack
H
Latch screws
Wood block
C
K
46780
F
Batteries
SmartKey tool
L
Mounting plate screws
R
E
S
M
Interior assembly
screws
Interior cover
screws
U
48654
V
49191
64109
Note: Part numbers are printed on screw bags.
Kwikset: 1-800-327-5625 • www.kwikset.com
1 / 11
© 2017 Spectrum Brands, Inc.
1
Prepare the door and check dimensions
If drilling a new door, use the supplied template and the complete
door drilling instructions available at www.kwikset.com/doorprep.
A
Measure to confirm that the hole in the door
is either 2-1/8" (54 mm) or 1-1/2" (38 mm).
B
Measure to confirm that the backset is
either 2-3/8" or 2-3/4" (60 or 70 mm).
2-3/8" or 2-3/4"
60 or 70 mm
2-1/8"
ba
ck
se
t
54 mm
or
1-1/2"
38 mm
Note: Additional door preparation may be required for
doors with 1-1/2" (38 mm) holes. Consult the deadbolt
drilling instructions at www.kwikset.com/doorprep
C
D
Measure to confirm that the hole in
the door edge is 1" (25 mm).
Measure to confirm that the door is between
1-3/8" and 2" (35 mm and 51 mm) thick.
1-3/8"– 2"
35 – 44 mm
1"
25 mm
Kwikset: 1-800-327-5625 • www.kwikset.com
2 / 11
© 2017 Spectrum Brands, Inc.
2
A
Install the latch and strike
B
Is the door edge chiseled?
YES
Hold the latch in front of the door hole, with the latch
face flush against the door edge.
D
Latch “A”
NO
chiseled
or
Use latch “A”. If the
latch bolt is not already
extended, extend the
latch bolt as shown.
A
Which latch are you installing?
not
chiseled
B
A
Use latch “B”. If the
latch bolt is not already
extended, extend the
latch bolt as shown.
B
Latch “B”
or
B
“UP” is
on top
C
“UP” is
on top
A
Is the D-shaped hole centered in the door hole?
YES
N (2x)
NO
wood
block
or
D-shaped hole centered
D-shaped hole NOT centered
No adjustment is required.
Proceed to next step.
Rotate latch face as
shown to extend latch.
E
A
Install strike on the door frame.
Make sure the hole in the door frame is drilled a
minimum of 1" (25 mm) deep.
Longer screws, Q,
install closest to
the door jamb.
B
Q (2x)
R (2x)
C
door frame
Note: The longer screws, Q, (3" / 76 mm) must be used
to maintain highest security.
Kwikset: 1-800-327-5625 • www.kwikset.com
3 / 11
© 2017 Spectrum Brands, Inc.
3
A
Install the exterior assembly
C
What is the diameter of the hole in the door?
Diameter is 2-1/8" (54 mm)
2-1/8"
a
Diameter is 1-1/2" (38 mm)
or
Install exterior assembly and mounting plate.
b
Cable goes
underneath
latch.
D
1-1/2"
54 mm
Support exterior
assembly during
mounting plate
installation.
38 mm
“E” is required for installation.
Install “E” on “D”.
Route cable
through center
hole, then
push cable into
bottom hole.
“E” is not needed for
installation. Discard “E”.
E
D
Rotate torque blade to align
with D-shaped hole.
E
c
B
Keep parallel to
edge of door
d
F
Locate screws for step 3C and keep them within reach.
S
S
Tighten
screws evenly.
S
G
Insert key and test latch.
If latch does not extend
or retract smoothly,
adjust screws (S).
Remove key when finished
and make sure the latch
bolt is fully extended.
Kwikset: 1-800-327-5625 • www.kwikset.com
4 / 11
© 2017 Spectrum Brands, Inc.
4
A
Install the interior assembly
Remove battery cover and battery pack from interior assembly.
a
b
Make sure
turnpiece is in the
vertical position.
c
Remove
interior cover.
Remove
battery pack.
J
K
H
K
H
vertical
Do not install
batteries yet.
B
Connect cables and install interior assembly.
a
c
b
Push turnpiece shaft
onto torque blade.
d
Secure with
screws.
H
U (2x)
Ensure tight cable
connection.
align
turnpiece
shaft
Lay excess cable flat
inside the bottom of
the interior housing.
Kwikset: 1-800-327-5625 • www.kwikset.com
5 / 11
torque
blade
bottom hole
© 2017 Spectrum Brands, Inc.
5
Perform the door handing process
This step will teach the lock the orientation of your door and is crucial for lock operation.
A
C
Install 4 AA batteries in the battery pack.
After a few seconds, the latch bolt will retract and extend on its
own to learn the orientation of the door. This is called the door
handing process, and it is crucial to lock operation.
L (4x)
Once the door handing process
is complete, the touchscreen
will indicate success or failure:
J
Ensure correct polarity. For best
results, use new, non-rechargeable
Alkaline batteries only.
B
Success:
flashing checkmark
symbol and single
column of digits
Make sure the door is open. Insert the battery pack.
D
Failure:
flashing
“X” pattern
If the touchscreen indicates a failure, peform the
manual door handing procedure on page 10.
If the door handing process is still unsuccessful, consult the online
User Guide at www.kwikset.com/support/guides/premis-user.
Kwikset: 1-800-327-5625 • www.kwikset.com
6 / 11
© 2017 Spectrum Brands, Inc.
6
Install the interior cover
a
b
Install
cover.
Install
screws.
V (3x)
K
7
OPTIONAL: Re-key the lock
If desired, the lock may be re-keyed to work with your existing key.
See the supplied SmartKey Re-key instructions for more information.
8
Download the Premis app and pair your lock to your phone
A
Download the Premis app from the App Store.
B
Follow the instructions inside the app to pair your smartphone, manage
the settings of your lock, and send user codes to family and friends.
Compatibilty
HomeKit™ requires an iPhone®, iPad® or iPod touch® with iOS 8.1 or later.
Controlling HomeKit-enabled accessories away from home requires
an Apple TV® (4th generation or later) with Apple TV® software 7.0
or later and an iPhone®, iPad® or iPod touch® with iOS 8.1 or later.
For best results, lock should be within 40 feet of
an Apple TV® for remote capability.
Kwikset: 1-800-327-5625 • www.kwikset.com
7 / 11
© 2017 Spectrum Brands, Inc.
Premis at a Glance
Locking and Unlocking
With the Premis App
Exterior
When you are within Bluetooth range of your lock, you can use Siri commands to lock and unlock your door.
Make sure your phone is unlocked, and refer to your lock by the name you assigned to it inside the Premis
app. You can also tap the symbol of your lock inside the Premis app to lock and unlock the door.
If you have an Apple TV (4th generation or later), you can lock and unlock the door when you’re away
from home. Just sign in to iCloud with the same Apple ID on your phone and Apple TV.
Touchscreen
Note: Remote locking and unlocking functionality will be disabled if your Apple TV goes to sleep. It is
recommended that you disable your Apple TV's sleep mode inside your Apple TV's settings.
Checkmark
symbol
Lock
symbol
SmartKey
tool hole
Keyway
With the Touchscreen
To lock and unlock your door with the Premis touchscreen, you must have at least one user code programmed.
It is recommended that you add your user codes from inside the Premis app. If you would like to add them
directly at the lock, follow the instructions at www.kwikset.com/support/guides/premis-user.
Locking the Door
Interior (cover removed)
1.
Activate the screen.
1.
2. Press Lock symbol.
Note: If no user codes are
programmed, the door cannot
be locked via touchscreen.
Back
panel
Button “A”
Auto-Lock
Unlocking the Door
Activate the screen.
2. If SecureScreen™ is enabled, touch
the random digits that appear.
3. Enter user code.
Button “B”
You may also adjust the
time delay (between 30
seconds and 4 minutes)
within the app.
Program
button
Status
LED
The Auto-Lock feature
automatically re-locks
your door 30 seconds
after unlocking. This
feature is off by default,
but you may enable it
inside the Premis app.
Switches
(Not used)
If you press the wrong digit while entering a user code, you
can press the Lock symbol once to clear the digits entered
previously and immediately restart the code entry process.
Turnpiece
shaft
Activating the Screen
Note: When the cover is removed,
the turnpiece shaft can be used to
manually lock and unlock the door.
Option 1
Touch screen with
palm or back of
hand until digits
illuminate.
SecureScreen™
Option 2
Touch lower left
area of screen
(where checkmark
is located) until
digits illuminate.
Option 3
Touch screen
with three or
more fingers until
digits illuminate.
SecureScreen is an added-security feature that displays
random digits before you enter a user code to unlock
the door. This feature ensures that there are fingerprints
on all digits so that codes cannot be identified by
examining the touchscreen for finger prints.
If desired, this feature
can be disabled inside
the Premis app.
Kwikset: 1-800-327-5625 • www.kwikset.com
8 / 11
© 2017 Spectrum Brands, Inc.
Lights and Sound
Status LED Colors
The Status LED blinks every 6 seconds on lock interior to communicate
whether the door is locked or unlocked, or if the batteries are low. The
Status LED may be turned off inside the Premis app.
Note: During the pairing process, the Status LED will flash red and green,
followed by a short beep (if the lock's sound is not muted).
Sound
The lock beeps during normal use and programming. If desired, you may
mute the lock inside the Premis app.
Amber flash
Door is locked
Green flash
Door is unlocked.
Red flash
The 4 AA batteries in the
interior assembly are low and
need to be replaced.
System Alerts
Note: Beeping will not be heard if the lock’s sound is muted.
X-pattern
Flashes 1 time with 1 beep
• Incorrect user code entered.
Flashes 3 times with 3 beeps
• No user codes programmed.
• Programming timeout after 20 seconds.
• Unsuccessful programming.
Checkmark & Lock
Flashing simultaneously 5 times
with long continuous beep
• Low battery.
Beeping only
Lock beeps continuously
• Tamper alarm sounds when cable is disconnected.
Remove the battery pack, reconnect the
cable, and reinstall the battery pack.
Alternate flashing 5 times with long continuous beep
• Door jammed while attempting to lock.
Flashes 15 times with 15 beeps
• 3 incorrect codes entered within 1 minute (you may
re-enter code after 60 second touchscreen lockout).
Kwikset: 1-800-327-5625 • www.kwikset.com
9 / 11
© 2017 Spectrum Brands, Inc.
Manual Door Handing
If needed, the door handing process can be initiated manually.
This is useful if the lock is being moved to a different door.
1 Remove battery pack.
2 Press and HOLD the
Program button while
reinserting the battery pack.
3 Press the Program
button once more.
4 The latch bolt will extend and retract to learn the
orientation of the door.
Release button once battery
pack is installed. The status
LED will flash red and green.
Status
LED
Success
Failure
If the touchscreen indicates a failure, see the online Premis User
Guide at www.kwikset.com/support/guides/premis-user.
Resetting the Lock
Three methods are available to reset your
Premis lock, depending on your needs:
1. Network Reset
3. Factory Reset
A network reset will do the following:
A factory reset will do the following:
• Remove the lock from your Premis app and HomeKit system.
All users and schedules will still be in place after a network reset. They
will be rediscovered by the Premis app once you pair the lock again.
From the Premis App:
Follow the instructions in the Premis app
to delete your lock.
From the lock:
Press and hold Button “A” on the back panel
for 7 seconds, until the lock beeps one time.
• Remove the lock from your Premis app and HomeKit system.
• Remove all users, schedules, and user codes
that were added inside the app.
• Remove all user codes that were
programmed directly at the lock.
• Disable Auto-Lock.
Follow the instructions below to perform a factory reset:
1 Remove battery pack.
A system reset will do the following:
Remove the lock from your Premis app and HomeKit system.
Remove all users, schedules, and user codes that were added inside the app.
Remove all user codes that were programmed directly at the lock.
Disable Auto-Lock.
Turn on the Status LED if it was turned off inside the Premis app.
Re-enable SecureScreen if it was disabled inside the Premis app.
Unmute sound if it was muted from the Premis app.
To perform a system reset, press and hold Button “A” on the
back panel for 20 seconds. The lock will beep after 7 seconds.
Keep holding until you hear a second beep.
Kwikset: 1-800-327-5625 • www.kwikset.com
2 Press and HOLD the
Program button while
reinserting the battery pack.
Keep holding the button for
30 seconds until the lock
beeps and the status LED
flashes red.
2. System Reset
•
•
•
•
•
•
•
• Turn on the Status LED if it was turned
off inside the Premis app.
• Re-enable SecureScreen if it was
disabled inside the Premis app.
• Unmute sound if it was muted from the Premis app.
• Initiate the door handing process
3 Press the Program
button once more. The
status LED will flash
green and red several
times.
4 After a few seconds, the lock will initiate the door handing process, and the latch
bolt will extend and retract to learn the orientation of the door.
10 / 11
© 2017 Spectrum Brands, Inc.
Troubleshooting
A complete troubleshooting guide is located in the online Premis User
Guide at www.kwikset.com/support/guides/premis-user.
Important Safeguards
•
•
•
•
•
•
•
•
•
•
Protect your user codes and mastercode.
Familiarize yourself with all warning and caution statements.
Remind all family members of safety precautions.
Dispose of used batteries according to local laws and regulations.
Always have access to your lock’s standard key.
Replace low batteries immediately.
Protect the password to your Premis app.
Protect your phone by enabling Touch ID and/or setting a passcode.
When sending a user code, always double-check that you are sending it to the correct recipient.
Protect and restrict access to your smartphone so that your app settings cannot be altered without your knowledge.
CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict
access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use
of a mastercode can help protect your settings.
WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or
technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment,
and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance
security and reduce risk, you should consult a qualified locksmith or other security professional.
Kwikset: 1-800-327-5625 • www.kwikset.com
11 / 11
© 2017 Spectrum Brands, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising