Operating instructions SONY CDP

Operating instructions SONY CDP
You can read the recommendations in the user guide, the technical guide or the installation guide for SONY CDP-XE370. You'll
find the answers to all your questions on the SONY CDP-XE370 in the user manual (information, specifications, safety advice, size,
accessories, etc.). Detailed instructions for use are in the User's Guide.
User manual SONY CDP-XE370
User guide SONY CDP-XE370
Operating instructions SONY CDP-XE370
Instructions for use SONY CDP-XE370
Instruction manual SONY CDP-XE370
You're reading an excerpt. Click here to read official SONY CDPXE370 user guide
http://yourpdfguides.com/dref/686828
Manual abstract:
@@Model No. @@The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. This symbol is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This
symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the
appliance. AC power cord must be changed only at the qualified service shop. Do not install the appliance in a confined space, such as a bookcase or built-in
cabinet. To prevent fire, do not Cover the ventilation of the apparatus with news papers, table-cloths, curtains, etc. And don't place lighted candles on the
apparatus. To prevent fire or shock hazard, do not place vases on the appartus. Don't throw a battery, dispose it as the injurious wastes.
INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. Consult the dealer or an experienced radio/TV technician for help. This Class A digital apparatus complies with Canadian ICES-003. CAUTION
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET
UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
About this manual The instructions in this manual are for CDP-XE570, CDP-XE370, and CDP-XE270. CDP-XE570 is the model used for illustration
purposes only. Any difference in operation is clearly indicated in the text, for example, "CDP-XE570 only." Tip CAUTION You are cautioned that any
changes or modification not expressly approved in this manual could void your authority to operate this equipment. 2 Instructions in this manual describe the
controls on the player. You can also use the controls on the remote if they have the same or similar names as those on the player (CDP-XE570/XE370 only).
Table of Contents Parts Identification 4 Front Panel ....
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
.. 4 Rear Panel ........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
@@@@@@@@8 Playing the CD Normal Play/Shuffle Play/Repeat Play .....
.....
..........
..........
.....
.....
..........
... 9 Using the CD display .......
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
. 10 Repeating a Specific Portion (AyB Repeat) (CDP-XE570 only) .........
..........
.....
.....
......... 11 Programming the CD tracks .
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
....... 12 Fading In or Out (CDP-XE570/XE370 only) ...
.....
.....
..........
..........
.....
.....
..........
..........
.....
.... 13 FR Recording From CDs (CDP-XE570 only) Recording a CD by Specifying Tape Length (Time Edit) .
..........
..........
.....
.....
..........
..........
.. 13 Adjusting the Recording Level (Peak Search) ...
.....
..........
..........
.....
.....
..........
..........
.....
.....
.. 14 Additional Information Using the CONTROL A1II control system (CDP-XE570 only) ........
..........
.....
.....
..........
.... 15 Precautions ......
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
........ 17 Notes on CDs ..
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
......... 17 Troubleshooting .
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
...... 18 Specifications ....
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
..........
.....
.....
..........
...... 18 3 Parts Identification Front Panel The items are arranged in alphabetical order. @@@@@@@@@@@@@@@@Doing so may cause a
malfunction. @@Press ANALOG OUT LEVEL +/ on the remote. You can reduce the analog output level up to 20 dB.
@@When you turn off the player, the output level automatically returns to the maximum level. Setting the voltage selector (voltage selector equipped models
only) Check that the voltage selector on the rear panel of the player is set to the local power line voltage. If not, set the selector to the correct position using a
screwdriver before connecting the AC power cord to a wall outlet. 220 - 240 V 110 - 120 V continued 7 Playing CDs Hooking Up the System (continued)
Loading a CD Making digital hookups If you have a digital component such as a digital amplifier, D/A converter, DAT, or MD, connect the component via the
DIGITAL OUT (OPTICAL) connector using the optical cable (not supplied). Take off the cap and plug in the optical cable.
Note that you cannot use the following functions when making this connection: · Fading In or Out (CDP-XE570/XE370 only) (see page 13) · Adjusting the
output level using the ANALOG OUT LEVEL +/ buttons on the remote (CDP-XE570/XE370 only) POC-15 Optical cable (not supplied) CD player Digital
component When you play a CD single, place it on the inner circle of the tray. 1 Turn on the amplifier and select the CD player position so that you can listen
to the sound from this player. 2 Press POWER to turn on the player. 3 Press AOPEN/CLOSE. The disc compartment slides out.
4 Place a disc on the disc tray with the label side up. DIGITAL OUT OPTICAL DIGITAL INPUT 5 Press AOPEN/CLOSE to close the disc compartment.
OPTICAL Note When you connect via the DIGITAL OUT (OPTICAL) connector, noise may occur when you play CD software other than music, such as a
CDROM. Tip (CDP-XE570 only) If you have a Sony component with the CONTROL A1II jack, connect the component via the CONTROL A1II jack. You can
simplify the operation of audio systems composed of separate Sony components. For details, see "Using the CONTROL A1II control system" on page 15. 8
Playing the CD Normal Play/Shuffle Play/Repeat Play This unit lets you play the CD in different play modes. Other Operations To Do this Stop playback
Pause Select a track Press x. Press X. Press X again or H to resume play.
During play or pause, turn lAMSL clockwise (to go forward) or counterclockwise (to go backward) (or press >( to go forward) or . (to go backward) on the
remote (CDP-XE570/XE370 only)). Press the number button on the remote.* Press and hold M or m during playback, and release at the desired point. Press
PLAY MODE until "SHUFFLE" appears in the display. Press AOPEN/CLOSE. Press ANALOG OUT LEVEL +/ on the remote. Getting Started 1 Press PLAY
MODE repeatedly until the mode you want appears. Select To play CONTINUE SHUFFLE PROGRAM The CD in the original order. The tracks on the CD in
random order.
The tracks on the CD in the order you want them to be played (see "Programming the CD tracks" on page 12). Select a track directly Find a point in a track
Playing CDs 2 Press H. Tip (CDP-XE570/XE370 only) Play tracks in random order Remove the CD Adjust the volume You can select the playing mode by
pressing CONTINUE, SHUFFLE, or PROGRAM on the remote. Repeat Play Operations You can play the CD tracks repeatedly in any play modes.
You're reading an excerpt. Click here to read official SONY CDPXE370 user guide
http://yourpdfguides.com/dref/686828
To activate the Repeat Play function, press REPEAT until "REPEAT' appears in the display.
To Press REPEAT * When you directly locate a track numbered over 10, press >10 first, then the corresponding number buttons. To enter "0," use button 10.
Example: To play track number 30 Press >10 first, then 3 and 10. Tips Repeat only one track Until "REPEAT 1" appears while playing the track you want to
repeat. Until "REPEAT" or "REPEAT1" disappears.
Cancel Repeat Play When you are in the Repeat Play function, the player repeats the tracks as follows: When the disc is played in The player repeats · You
can adjust the analog output level with the ANALOG OUT LEVEL +/ on the remote (pageappears instead of the remaining time. · The display may not show
all the characters depending on the disc. · This player can only display the disc titles, track titles and artist names from CD TEXT discs. @@@@@@When
you resume play, the display turns off again. @@@@@@@@@@@@@@@@@@@@@@@@@@ " appears instead of the total playing time.
@@@@@@@@@@@@For the CDPXE570, "FADE" flashes. For FADE the CDP-XE370, lights up in the display and the Q indication flashes. The play
fades in. End play fading out When you want to start fading out. For the CDP-XE570, "FADE" flashes.
For the CDPFADE XE370, lie compatible with components with CONTROL A1II, and can be connected to each other. Basically, the majority of the functions
available with the CONTROL A1 control system will be available with the CONTROL A1II control system.
@@@@@@@@@@@@@@@@@@@@Certain receivers allow you to switch the names of the function buttons. In this case, refer to the operating
instructions supplied with the receiver. · When recording, do not play any components other than the recording source. It will cause the automatic function
selection to operate. 16 Precautions On safety · Caution -- The use of optical instruments with this product will increase eye hazard. @@@@Attempting to do
so may damage the unit. @@Do not touch the surface. @@The operating voltage is indicated on the nameplate at the rear of the player.
· The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. · If
you are not going to use the player for a long time, be sure to disconnect the player from the wall outlet. To disconnect the AC power cord (mains lead), grasp
the plug itself; never pull the cord. · AC power cord must be changed only at the qualified service shop. · Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be considerable rise in temperature inside the car.
· Do not use any commercially available stabilizer. If you do, the disc and the player may be damaged. · After playing, store the disc in its case. On cleaning ·
Before playing, clean the disc with a cleaning cloth. Wipe the disc from the centre out.
On placement · Place the player in a location with adequate ventilation to prevent heat build-up in the player. @@@@Should this occur, the player may not
operate properly. @@@@If you do, the speakers may be damaged when a peak level portion is played. On cleaning · Clean the cabinet, panel and controls
with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent such as alcohol or
benzine. 17 Troubleshooting If you experience any of the following difficulties while using the player, use this troubleshooting guide to help you remedy the
problem. Should any problem persist, consult your nearest Sony dealer. There's no sound. Specifications Compact disc player Laser Semiconductor laser ( =
780 nm) Emission duration: continuous 2 Hz to 20 kHz ± 0.5 dB More than 93 dB 0.
0045% · Check that the player is connected securely. · Make sure you operate the amplifier correctly. · Adjust the analog output level with ANALOG OUT
LEVEL +/ on the remote (CDP-XE570/ XE370 only). The CD does not play. Frequency response Dynamic range Harmonic distortion Outputs Jack type
Maximum output level Load impedance · There's no CD inside the player. " NO DISC " (or "no dISC" for the CDP-XE370/XE270) appears. Insert a CD. ·
Place the CD with the label side up on the disc tray correctly. · Clean the CD (see page 17). · Moisture has condensed inside the player.
Remove the disc and leave the player turned on for about an hour. The recording level has changed. ANALOG OUT Phono jacks 2V (at 50 kilohms) Over 10
kilohms Wave length: 660 nm 32 ohms DIGITAL Optical 18 dBm OUT output (OPTICAL) connector PHONES Stereo (CDP-XE570 phone only) jack 10 mW ·
The recording level changes if you adjust the analog output level with ANALOG OUT LEVEL +/ on the remote during recording (CDP-XE570/XE370 only).
The remote does not function (CDP-XE570/XE370 only). General Power requirements Where purchased Power requirements USA Europe Australia Some
Asian countries 120 V AC, 60 Hz 230 V AC, 50/60 Hz 240 V AC, 50/60 Hz 220 V 230 V AC, 50/60 Hz · Remove the obstacles in the path of the remote and the
player.
on the · Point the remote at the remote sensor player. · Replace all the batteries in the remote with new ones if they are weak. Power consumption Dimensions
(approx.) (w/h/d) Mass (approx.) 11 W 430 x 95 x 290 mm (17 x 3 3/4 x 11 1/2 in.
) incl. projecting parts CDP-XE570: 3.3 kg (7 lbs 5 oz) CDP-XE370: 3.2 kg (7 lbs 1 oz) CDP-XE270: 3.2 kg (7 lbs 1 oz) Supplied accessories Audio cord (2
phono plugs 2 phono plugs) (1) Remote commander (remote) (1) (CDP-XE570/ XE370 only) R6 (size AA) batteries (2) (CDP-XE570/XE370 only) Design and
specifications are subject to change without notice. 18 Additional Information 19 Sony Corporation Printed in Malaysia .
You're reading an excerpt. Click here to read official SONY CDPXE370 user guide
http://yourpdfguides.com/dref/686828
Powered by TCPDF (www.tcpdf.org)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising