Data Sheet - Microsens
Data Sheet
Ruggedized Gigabit Ethernet Micro Switch
with extended temperature range
Overview
The ruggedized Micro Switch is part of the successful MICROSENS Fiber-To-The-Office
(FTTO) series. This model comes with an extended temperature range (-25°C up to
+85°C) and offers a mounted holder for 35 mm DIN-rails as option.
This model generally has a SFP uplink and is available in the following six versions:
Horizontal version
with 1x SFP Uplink and RJ-45 Donwlink
Vertical version
with 1x SFP Uplink and RJ-45 Donwlink
(shown in picture above)
Horizontal version
with 2x SFP Uplink
Vertical version
with 2x SFP Uplink
Horizontal version
with support of CSFP
Vertical version
with support of CFSP
The very compact switches excel with extremely low space requirements and are used in
switching cabinets without defined environmental conditions. The device is designed
monolithic and therefore offers shortest installation work, paired with highest robustness
and reliability.
The versions with 2 SFP uplinks are intended to be used in ring topologies. Their ring
functionality is equivalent and therefore hundred per cent compatible with the
MICROSENS industry switches of the Profi Line, Profi Line+ and Profi Line Modular series.
The whole configuration of the Micro Switch can be transferred to another system, just
by changing the SD-Card. A fault-tolerant journaling file-system is used and the SD-Card
is in accordance with industry standard. An encryption of the SD-Card is as option
available.
©2014_MICROSENS GmbH & Co. KG_Küferstr. 16_59067 Hamm/Germany_www.microsens.com
Data Sheet_Ruggedized Gigabit Eth. Micro Switch with ext. temp. range
Page 2/13
Features
Gigabit Ethernet Switch
Power-over-Ethernet PoE+
 Fanless Gigabit Ethernet Switch
 IEEE 802.3at PoE+ (max. 30 W/Port)
 Low power consumption switchchipset, Energy-Efficient Ethernet
 5x 10/100/1000Base-T, PoE+ (RJ-45)
 Layer-2+ store-and-forward,
full wire-speed, non-blocking
 Max. 8.192 MAC-addresses, automatic
Learning and aging
 Jumbo-Frames (max. 10,240 Bytes)
Energy-Efficient Ethernet
 Limitation of the total power
consumption of the switch to max.
80 W (full power only with suitable
installation conditions)
 Ext. power supply with typ. 54 VDC
Connectors
 EEE according to IEEE 802.3az
Uplink
 1x or 2x 1000Base-X SFP slot
 Optimised power consumption for
each RJ-45 port depending on the
actual requirement
Local / Downlink
 4x or 5x 10/100/1000Base-T (RJ-45)
Auto-Negotiation
 50% reduced power consumption
 Auto MDI/MDI-X function for the use
of uniform patch cables
Network Management
Power Supply
 3-pin screw pluggable connector for
solid or litz wires
 Supports all common management
standards
 High Performance 800 MHz ARM CPU
 Linux operating system with fast
system boot (approx. 30 seconds)
 Web Manager (HTTP/HTTPS)
 Telnet/SSH/Console, incl. standardcommands (ping, traceroute, etc.)
 SNMP v1/v2c/v3 with
View-based Access Control Model
(VACM) and User-based Security
Model (USM)
 Central management platform
(NMP Professional / NMP Server)
 IPv4/IPv6 Dual Stack
 Integrated CLI scripting for the
automation of routine processes
 Firmware-, Script- and configuration
files can be loaded, stored and
executed direct from the switch
 Additional grounding (PE) with 6,3
mm flat-pin plug
Extension Port
 RS-232 Console port
 For optional accessories
Mounting
 Installed holder for DIN-rails (DIN EN
50022)
 Horizontal version fits in panels of
switching cabinets
 Compatible to all popular installation
systems due to circumferential
installation face
Compatibility
 Compatibility to standard CISCO
Switches approved
 Incremental firmware updates
possible
 Modular MicroSD memory card for
configuration, CLI scripts, firmware,
encrypted data and MAC address
(optional)
©2014_MICROSENS GmbH & Co. KG_Kueferstr. 16_59067 Hamm/Germany_www.microsens.com
Data Sheet_Ruggedized Gigabit Eth. Micro Switch with ext. temp. range
Page 3/13
Network management - Feature overview
IP Stack
Dual Stack
Parallel handling of IPv4 and IPv6 protocol.
IPv4 Stack
Internet Protocol v4 handling with support of IPv4, ARP, DHCP, ICMP.
RFC 791 (IPv4), RFC 826 (ARP), RFC 792 (ICMP), RFC 2131 (DHCP)
IPv6 Stack
Internet Protocol v6 handling with support of IPv6, DHCPv6, ICMPv6, NDP.
RFC 2460/2464/3484/3513 (IPv6), RFC 2462 (Address Configuration), RFC 2463
(ICMPv6), RFC 2461 (Neighbour Discovery Protocol), RFC 3315 (DHCPv6)
Port Control
Administration
Port disable, Individual port alias
Ethernet Copper
Auto-Negotiation, speed, duplex mode, flow-control, Auto MDI/MDI-X
Ethernet Fiber/SFP
Speed, duplex mode, flow-control
Green IT
Latest chip technology supports Energy-Efficient Ethernet (EEE) according to
IEEE Std. 802.3az.
Power-over-Ethernet (PoE)
Function
Sourcing of power to connected devices via standard network Twisted-Pair cable
802.3at mode
PoE+ voltage is turned on only after powered device (PD) is detected and
classified on port. Output voltage and power is monitored. Port power is shut
down if limits are exceeded.
802.3af mode
PoE voltage is turned on only after powered device (PD) is detected and
classified on port. Output voltage and power is monitored. Port power is shut
down if limits are exceeded.
Power Management
Power limit can be defined per port and per total device. Additionally the class of
the powered device (PD) can be limited per port.
Standards
IEEE Std. 802.3af (Data Terminal Equipment Power via Media Dependent
Interface), IEEE Std. 802.3at (Data Terminal Equipment Power via Media
Dependent Interface).
Switch Functions
Port Monitor
Monitor port for the connection of a network protocol analyzer. Traffic of the port
to be analyzed is copied to the monitor port.
RMON counters
17 Integrated counters for detailed traffic analysis and network trouble shooting.
MAC Table
Access to table of MAC addresses learned by the switch. Can be filtered per port,
VLAN address type and entry type (dynamic/static).
Virtual LANs (VLANs)
Function
Logical structuring of physical networks by adding a Virtual LAN ID (VID) to each
Ethernet packet. Incoming packets are filtered and forwarded according to their
VID. Each port can be configured for Access, Hybrid or Trunk VLAN processing
mode. Independent VLANs out of the full range of 1 to 4095 can be filtered per
device.
Access Mode
For the connection of non-VLAN capable end devices (e.g. PCs). Outgoing
packets are sent untagged. Incoming packets are tagged with the port default
VLAN ID (PVID).
Trunk Mode
For the interconnection of VLAN capable switches. Outgoing packets are always
sent tagged. Incoming packets are received tagged. Incoming packets without
VLAN tag are tagged with the port default VLAN ID (PVID).
Hybrid Mode
For the connection of VLAN capable and non-VLAN capable devices on the same
port (e.g. VoIP-phone (tagged) and PC (untagged)). Outgoing packets are sent
tagged, except packets for the port default VLAN ID (PVID), which are untagged.
Incoming packets are received untagged for the port default VLAN (PVID), all
other packets are tagged.
©2014_MICROSENS GmbH & Co. KG_Kueferstr. 16_59067 Hamm/Germany_www.microsens.com
Data Sheet_Ruggedized Gigabit Eth. Micro Switch with ext. temp. range
Page 4/13
Priority Override
VLAN priority code point of incoming packets can be overwritten with the VLAN
specific priority defined in the VLAN filter.
Voice VLAN
VLAN ID used by LLDP/CDP to assign VLAN to connected VoIP-phone.
RSTP VLAN
VLAN ID used by Spanning Tree instance for BPDU tagging.
Unauthorized VLAN
VLAN ID assigned by Port Based Access Control to unauthorized ports
(guest VLAN).
Management VLAN
VLAN ID used by the management agent (device internal port).
Standard
IEEE Std. 802.1D, IEEE Std. 802.1Q, IEEE Std. 802.1p
Quality of Service (QoS)
Priority Queues
4 priority queues per port.
Prioritization
Scheme
Strict priority (higher priority always first) or weighted fair queuing (8:4:2:1
highest to lowest).
Layer1 Priority
Static priority queue can be assigned for each port.
Layer2 Priority
Incoming packets are forwarded according to the priority code point in their
VLAN tag. The 8 VLAN priority code points can be individually mapped on the 4
priority queues.
Layer3 Priority
Incoming packets are forwarded according to the value of the DiffServ Codepoint
(IPv4) / TrafficClass (IPv6) in their IP header. Maximum 64 code points are
supported. For each code point the corresponding priority queue can be mapped.
Traffic shaping
5 ingress rate shaping buckets per port. Supports rate and priority based rate
shaping
Standard
IEEE Std. 802.1p (VLAN priority code point), RFC 2474/3260 (IPv4 DiffServ/IPv6
Traffic Class)
Spanning Tree Protocol / Ring Protocol
Rapid Spanning
Tree (RSTP)
Automatic detection of loops and redundant network paths. Single STP instance
running in configurable VLAN. Rapid Spanning Tree Protocol (RSTP) backwards
compatible to Spanning Tree standard (STP).
MSTP
Separate STP instances running in configurable VLAN groups.
PVST
RSTP per VLAN for one VLAN
MICROSENS Ring
Protocol
MICROSENS Redundant Ring Protocol with ultra-fast recovery time <20 ms
within MICROSENS Ring topologies.
Multicast Forwarding
IGMP Snooping
Snooping of Internet Group Management Protocol (IGMPv1/v2/v3) for IPv4.
Automatic detection and forwarding of IPv4 multicast-streams. Unregistered
packets can be flooded or blocked. Multicast routers can be detected by
discovery or by query message.
Standard
RFC 4541 (IGMP)
Link Layer Discovery Protocol (LLDP)
Function
Advertising identity, capabilities, and neighbours on a connected network
segment.
LLDP-MED
Media Endpoint Discovery for the auto-discovery of LAN policies.
Standard
IEEE Std. 802.1AB (LLDP), ANSI/TIA-1057 (LLDP-MED)
Cisco Discovery Protocol (CDP)
Function
CDP v1, v2 for automatic detection of capabilities of neighbour CDP enabled
devices.
Voice VLAN
Support of Voice VLAN for configuration of connected Cisco VoIP-phone.
©2014_MICROSENS GmbH & Co. KG_Kueferstr. 16_59067 Hamm/Germany_www.microsens.com
Data Sheet_Ruggedized Gigabit Eth. Micro Switch with ext. temp. range
Page 5/13
Real Time Clock (RTC)
Function
Internal device clock can be synchronized with external NTP server.
Protocol
Simple Network Time Protocol (NTP)
Standard
RFC 4330 (NTP)
Port Access Control
Function
Port-Based Network Access Control with dynamic port VLAN support and fallback
to MAC based authentication methods. Network access is controlled at the port
level. Supports IEEE Std. 802.1X Authentication, RADIUS MAC Authentication,
MAC Locking and forced authorized/unauthorized mode.
Communication
EAPOL, RADIUS
Authentication
Protocols
EAP-MD5, EAP-PEAP (inner protocol: MSCHAPv2), EAP-TLS, EAP-TTLS (inner
protocols: EAP-MD5, EAP-TLS, PAP)
IEEE 802.1X
Authentication
Multiple users can be authenticated using central RADIUS server based on
username/password or certificate.
RADIUS MAC
Authentication
Multiple users can be authenticated using central RADIUS server based on their
MAC addresses.
MAC locking
Multiple users can be authenticated based on their MAC addresses. Authorized
MAC addresses are stored permanently in the device. They can be configured
manually or automatically by locking the first MAC addresses learned on the port.
Dynamic VLAN
RADIUS server can provide user specific VLAN ID using tunnel-attribute in accept
message. Port VLAN is dynamically set accordingly. Unauthorized users may be
placed in an unauthorized VLAN ('guest VLAN') or blocked completely.
IP Address
Detection
The IP address of the connected user is detected via ARP snooping. User IP
address information can be logged using RADIUS accounting function.
Standard
IEEE 802.1X-2004 (Port-Based Network Access Control).
User Login
Function
Implements user based and view based authentication and scope limiting.
Supports unlimited number of user/groups and views (limited by system memory
constrains only). Offers ultimate flexibility with precise access control.
Command Line Interface (CLI)
Function
Intuitive command-set with auto-complete and redo-buffer. Individual console
prompt string, Console inactivity timeout. Supports full scripting and editing of
script files. Supports colour displays. Permits offline configuration as well as
management of an unlimited number of user configuration sets (limited by
system memory constrains only).
Telnet
Telnet via TCP/IP port 23.
Secure Shell (SSH)
SSH via TCP/IP port 22. Authentication methods RSA, Diffie-Hellman Key
Exchange. Encryption protocols 3DES-CBC, HMAC-SHA1.
Web Manager
Function
Integrated Web Manager with graphical user interface (GUI) for device
configuration and administration using standard web browser.
Protocol
HTML v4.01,HTTP, HTTPS, Java Script
Browser
compatibility
Firefox 4.x, IE 8.x, JavaScript support required.
©2014_MICROSENS GmbH & Co. KG_Kueferstr. 16_59067 Hamm/Germany_www.microsens.com
Data Sheet_Ruggedized Gigabit Eth. Micro Switch with ext. temp. range
Page 6/13
Simple Network Management Protocol (SNMP)
SNMPv1/v2c
Simple Network Management Protocol v1, v2c (SNMPv1, v2c) to access device
information stored in Management Information Base (MIB). Security provided by
community strings for Set/Get commands and optionally by G6 login scheme.
Traps
(SNMPv1/v2c)
Traps, Notifications sent to unlimited number of independently configurable
receiver destinations (limited by system memory constrains only). Sending of
message is triggered by internal device status change events.
Event triggers can be configured individually per destination. Test function to
trigger Trap/Notification for simplified configuration check (Web Manager and CLI
only).
SNMPv3
Simple Network Management Protocol v3 (SNMPv3) for secure access to device
information stored in Management Information Base (MIB). SNMPv3 supports data
encryption, User-based Security Model (USM) and View-based Access Control
Model (VACM).
Traps (SNMPv3)
Trap/Notification, InformRequest, Response sent to independently configurable
receivers. Sending of message is triggered by internal device status change
events. Informs provide secured messaging by requiring response message Event
triggers can be configured individually per receiver.
MIBs
MIB-2, Enterprise-MIB (MICROSENS G6 MIB). File can be downloaded from the
integrated Web Manager.
Standard
RFC 1155/1156/1157 (SNMPv1), RFC 1901/1905/1906 (SNMPv2), RFC
3411/3412/3584 (SNMPv3), RFC 2574/3414 (USM), RFC 2575/3415 (VACM)
RADIUS Client
Function
RADIUS client via UDP/IP ports 1812 (access), 1813 (accounting) for Remote
Authentication Dial In User Service (RADIUS) server for authorizing user access
and logging of user accounting information.
Redundancy
In case of a response timeout, the next RADIUS server is requested.
Standard
RFC 2865 (RADIUS), RFC 2866 (Accounting), RFC 2868 (Tunnel Attributes)
Files
Configuration
File transfers may be used to upgrade the software or to load configuration files.
The unit supports TFTP, FTP, SFTP, HTTP, HTTPS transfer protocols. Additionally
files may be loaded via DHCP directives.
Firmware Update
Software download can be complete or incremental. Individual modules may be
upgraded, normally without influencing service. Flexible system permits
customized upgrade files if required.
Syslog Client
Function
Syslog messages are triggered by system events and can be send to unlimited
number of Syslog servers (limited by system memory constrains only).
Standard
RFC 5424
Event Manager
Function
Mapping of device status changes (Triggers) to actions e.g. sending out SNMP
trap, Syslog message etc.
Customizable
events
Event severity and alert level freely configurable. Event text strings may be
customized via user interface with developer rights.
Traps and Syslog
Unlimited number of trap and/or Syslog receivers. Event may be filtered
individually on a group level.
©2014_MICROSENS GmbH & Co. KG_Kueferstr. 16_59067 Hamm/Germany_www.microsens.com
Data Sheet_Ruggedized Gigabit Eth. Micro Switch with ext. temp. range
Page 7/13
IEEE / RFC Standards
RFC Standards
RFC 791
IPv4
RFC 792
ICMP
RFC 826
ARP
RFC 1155
SNMPv1
RFC 1156
SNMPv1
RFC 1157
SNMPv1
RFC 1901
SNMPv2c
RFC 1905
SNMPv2
RFC 1906
SNMPv2
RFC 2131
DHCP
RFC 2460
IPv6
RFC 2461
IPv6 Neighbour Discovery
RFC 2462
IPv6 Auto Configuration
RFC 2463
ICMPv6
RFC 2464
IPv6
RFC 2474
IPv4 DiffServ
RFC 2574
USM
RFC 2575
VACM
RFC 2865
RADIUS
RFC 2866
Accounting
RFC 2868
Tunnel Attributes
RFC 3260
IPv6 DiffServ
RFC 3315
DHCPv6
RFC 3411
SNMPv3
RFC 3412
SNMPv3
RFC 3414
USM
RFC 3415
VACM
RFC 3484
IPv6
RFC 3513
IPv6
RFC 3584
SNMPv3
RFC 3810
MLD
RFC 4330
NTP
RFC 4541
IGMP Snooping
RFC 4604
MLD
RFC 5424
Syslog
IEEE Standards
802.1D-2004
(Rapid) Spanning Tree
802.1Q-2005
Multiple Spanning Tree
802.1p
QoS
802.1Q
VLAN
802.1X
Network Access Control
802.1AB
LLDP
802.3i
10Base-T
802.3u
100Base-TX
802.3x
Full duplex and flow control
802.3z
1000Base-X
802.3ab
1000Base-T
802.3af
Power-over-Ethernet
802.3at
Power-over-Ethernet (PoE+)
802.3az
Energy-Efficient Ethernet
Quality – Made in Germany
To guarantee constant high quality of the Micro Switch Generation 6 all models and
versions are produced in Germany on site Hamm.
Concluding each device has to pass a full load performance test on all network-ports
without any transmission error.
Additionally devices of each batch have to complete an extended (48h) burn-in-test, in
which they are functionally tested at high load, so early failures could be detected before
delivery.
©2014_MICROSENS GmbH & Co. KG_Kueferstr. 16_59067 Hamm/Germany_www.microsens.com
Data Sheet_Ruggedized Gigabit Eth. Micro Switch with ext. temp. range
Page 8/13
Interfaces
Title block
integrated
Reset/System Button
hidden
LED Display
Switch/Port/PoE Status
Lokal Ports
Energy Efficient Ethernet
PoE+ (max. 30 W)
Uplink Port
SFP/fixed/RJ-45 (PD)
Power Supply
54VDC / 230VAC
Extension Port
Terminal & more
Downlink Port
Energy Efficient Ethernet
PoE+ (max. 30 W)
Memory card
Firmware/Configuration
Bevelled edge
Simplifies installation in narrow housings
©2014_MICROSENS GmbH & Co. KG_Kueferstr. 16_59067 Hamm/Germany_www.microsens.com
Data Sheet_Ruggedized Gigabit Eth. Micro Switch with ext. temp. range
Page 9/13
Technical Specifications
Switch
Displays
Type
Gigabit Ethernet Switch
Layer 2+, IEEE 802.3 compliant
Performance
Store-and-forward
Full wire-speed, non-blocking
on all ports
MAC addresses
8.192 addresses, automatic
learning and aging
Jumbo Frames
max. 10.240 Bytes
Type
14 LEDs, detachable
Link
Twisted pair ports 1..4 and 6
green
Link at port.
Flashing at data traffic
oange Port blocked
(via protocol)
red
Port Access Control
rejected
PoE
Twisted
green
blue
orange
red
On
(switch status)
green
ready for operation
flashing starting sequence
Sys
blue
LED-modes
Dynamic
Static
Quiet
Dark
L-show
Twisted-Pair Ports
Number
4 or 5
Type
Gigabit Ethernet, Triple Speed
10/100/1000Base-T
Connector
RJ-45 port, shielded
Cable type
Twisted-Pair cable, Category
5e, impedance 100 Ohm, length
max. 100 m
Flow Control
Pause Frames (IEEE 802.3x),
configurable
Pin out
Auto MDI/MDI-X, Auto Polarity
Power-overEthernet
Power Sourcing Equipment
(PSE) IEEE 802.3af/at
Class 0, max. 30 W
Forced-mode (Legacy Devices)
Fiber Port
Type
SFP (Dual Speed)
100/1000Base-X, support of
SFP digital diagnostics function
Optional 2x SFP slot
(then only 4x TP)
Connector
LC typ. (depending on SFP)
Flow Control
Pause Frames (IEEE 802.3x),
configurable
Control Panel
Reset button
Reset of the switch, new upload
of the latest stored configuration
(direct hardware function)
System button
Request of the IP configuration
for management, reset back to
factory default settings
pair ports 1..4 and 6
PoE supplying
PoE+ active
PoE Standby
PoE failure
Factory reset without
IP reset in progress
violet
Factory reset including
IP reset in progress
green
Process completed
orange Flashing while Firmware update in progress
Standard-mode
Standard without flash
Only ON- and Sys-LED
all LEDs off
permanent LED test
Power Supply (DC Voltage)
Input
44..57 VDC (54 VDC typ.)
Power
Consumption
Typ. 4,5 W (without PoE)
max.80 W (incl. PoE)
(full power only with suitable
installation conditions)
Connectors
3 pin screw connector, PE/-/+
Grounding (PE)
6,3 mm flat-pin plug
Environmental Conditions
Temperature
Operation
Storage
-25..+65 °C
-25..+85 °C
Humidity
10..90%, non condensing
Mechanical
Dimensions
90 x 78,2 x 53,7 mm
(w x d x h, without connectors)
Mounting depth
34 mm
Weight
350 g
©2014_MICROSENS GmbH & Co. KG_Kueferstr. 16_59067 Hamm/Germany_www.microsens.com
Data Sheet_Ruggedized Gigabit Eth. Micro Switch with ext. temp. range
Page 10/13
Technical Specifications (continued)
Standards
Delivery / Contents
CE
2004/108/EC (EMV)
2006/95/EG (Low voltage)
Safety
EN 60950-1:2011-01
Emitted
interference
EN 55022:2011-12
Immunity
EN 55024:2011-09
Reliability
MTBF
100.000 h
Method
MIL-HDBK-217F
Standard Packaging
Package unit
1 pcs.
Dimensions
158 x 90 x 65 mm
Weight
400 g
Contents
1x Micro Switch
1x Micro-SD memory card
(separate article number)
1x Ground cable (PE), 20 cm
1x Power supply plug
1x Short manual
1x Set stickers with symbols
1x DIN-rail holder (mounted)
Memory Card
The MicroSD memory card is used for
the permanent storage of configuration,
script and firmware files. With this
memory card it is possible to transfer a
configuration to a new device in case of
a device failure.
 Change of memory card transfers the
complete device status
Optional it is possible to write an own
MAC address to the MicroSD memory
card. This MAC address has priority
compared to the MAC address in the
switch. This allows having an exact clone
of the device by swapping the memory
card.
 Industrial grade – long term stability
 Firmware update by memory card
exchange possible
 Fault tolerant journaling file system
 Encrypted system as security option
 Only MICROSENS memory cards have
to be used. Only with this the long
term stability over the complete
temperature range can be guaranteed.
©2014_MICROSENS GmbH & Co. KG_Kueferstr. 16_59067 Hamm/Germany_www.microsens.com
Data Sheet_Ruggedized Gigabit Eth. Micro Switch with ext. temp. range
Page 11/13
78 , 2
7 ,5
53 , 6
68 , 6
Dimensions
41 , 6
47 , 4
89 , 9
44 , 9
53 , 7
Horizontal Version
44,9
78,2
7,5
53,6
68,6
89,9
Vertical Version
41,6
47,4
©2014_MICROSENS GmbH & Co. KG_Kueferstr. 16_59067 Hamm/Germany_www.microsens.com
Data Sheet_Ruggedized Gigabit Eth. Micro Switch with ext. temp. range
Page 12/13
Ring-Topology (Dual Fiber-Uplink)
Normal operation
 All switches are configured for ring
operation
 One switch is assigned as ring master
 Ring master cuts the ring logically
Ring error
 Switches signalize segment failure via
ethernet (fiber-uplink)
 Master gets that information via ethernet
and closes the logical cut
 Switches relearn the actual network
topology (MAC-addresses)
 Network function is re-established in less
than 50 ms
Order Information
Description
Article-No.
Horizontal version
Article-No.
Vertical version
Ruggedized Micro Switch G6, incl. mounted holder for DIN-rails
1x SFP uplink (100/1000Base-X)
5x TP-Ports (10/100/1000Base-T) with PoE+
MS440209PMXH-48G6+
MS440219PMXH-48G6+
2x SFP uplink (100/1000Base-X)
4x TP-Ports (10/100/1000Base-T) with PoE+
MS440207PMXH-48G6
MS440217PMXH-48G6
MS440208PMXH-48G6+
MS440218PMXH-48G6+
Support of CSFP (Compact SFP)
Uplink 1x 100/1000Base-X, Downlink 10/100/1000T
or 2x Fiber-Uplink via 1000X simplex
Ruggedized Micro Switch G6, without holder for DIN-rails
1x SFP uplink (100/1000Base-X)
5x TP-Ports (10/100/1000Base-T) with PoE+
MS440209PMX-48G6+
MS440219PMX-48G6+
2x SFP uplink (100/1000Base-X)
4x TP-Ports (10/100/1000Base-T) with PoE+
MS440207PMX-48G6
MS440217PMX-48G6
MS440208PMX-48G6+
MS440218PMX-48G6+
Support of CSFP (Compact SFP)
Uplink 1x 100/1000Base-X, Downlink 10/100/1000T
or 2x Fiber-Uplink via 1000X simplex
Memory cards for ruggedized G6 Micro Switch (extended temperature range -25 °C up to +85 °C)
MicroSD Memory card 4 GB for MICROSENS G6-Switches,
MS140894X-4G
MicroSD Memory card 4 GB for MICROSENS G6-Switches,
With own MAC address
MS140894X-4G-M
MicroSD Memory card 4 GB for MICROSENS G6-Switches,
With individual switch configuration according to customer specifications
MS140894X-4G-C
MicroSD Memory card 4 GB for MICROSENS G6-Switches,
With individual switch configuration according to customer specifications and own
MAC address
MS140894X-4G-MC
©2014_MICROSENS GmbH & Co. KG_Kueferstr. 16_59067 Hamm/Germany_www.microsens.com
Data Sheet_Ruggedized Gigabit Eth. Micro Switch with ext. temp. range
Page 13/13
Accessories
Description
Article No.
SFP Transceiver (extended temperature range -40 °C up to +85 °C)
SFP Transceiver, Gigabit Ethernet, Digital Diagnostic
850 nm Multimode, 1000Base-SX, LC duplex
MS100200DX
SFP Transceiver, Gigabit Ethernet, Digital Diagnostic
1310 nm Single Mode, 1000Base-LX, LC duplex
MS100210DX
SFP Transceiver, Fast Ethernet, Digital Diagnostic
1310 nm Multimode, 100Base-FX, LC duplex
MS100190DX
SFP Transceiver, Fast Ethernet, Digital Diagnostic
1310 nm Single Mode, 100Base-FX, LC duplex
MS100191DX
CSFP (Compact SFP) Transceiver (extended temperature range -40 °C up to +85 °C)
Compact SFP - 2 Channel WDM Transceiver Gigabit Ethernet,
2x Single Mode simplex LC, Tx:1310nm, Rx:1490nm,
10 dB Budget / 10km, Digital Diagnostic, -40..+85°C
MS100650DXA
Tx:1490nm, Rx:1310nm
MS100650DXB
Title Block Sheets
Set of A4 sheets, each with 80 labels fitting for the Micro Switch
G6 title block
10 sheets per set, suitable for laser printers, perforated
MS140005
Network Management
NMP Professional – Network Management Platform
Software incl. one year update license
MS200160-1
NMP Professional – additional update license for n years
MS200161-n
NMP Standard – Network Management Platform
Software incl. one year update license
MS200162-1
NMP Standard – additional update license for n years
MS200163-n
NMP Server – Network Management Platform
Software incl. one year update license and 5 clients
MS200164-1
NMP Server – additional update license for n years
MS200165-n
External Power Supplies for industrial use with PoE / PoE+ 44..57VDC
DIN Rail Power Supply 60 Watt 48 VDC / 1.25 A,
Adjustment range 48..56VDC, Wide input range 85-264 VAC
MS700430
DIN Rail Power Supplies 192 Watt 48 VDC / 4 A,
Adjustment range 48..56VDC, Wide input range 85-264 VAC
MS700467
DIN Rail Power Supply 60 Watt 48 VDC / 1.25 A,
Adjustment range 41..58VDC,
Wide input range 90-264VAC, 85..200VDC
For extended temperature range -40..+75°C
MS700482-48B
This document in whole or in part may not be duplicated, reproduced, stored or retransmitted without prior written permission of MICROSENS GmbH
& Co. KG. All information in this document is provided ‘as is’ and subject to change without notice. MICROSENS GmbH & Co. KG disclaims any
liability for the correctness, completeness or quality of the information provided, fitness for a particular purpose or consecutive damage.
MICROSENS is a trademark of MICROSENS GmbH & Co. KG. Any product names mentioned herein may be trademarks and/or registered trademarks
of their respective companies. Aku/hb MS4402xx_MS6_RUG_DAT_EN_v1.0.2.docx
©2014_MICROSENS GmbH & Co. KG_Kueferstr. 16_59067 Hamm/Germany_www.microsens.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising