1995-up Mitsubishi Eclipse

1995-up Mitsubishi Eclipse
RADIO
EQ
STACK
TUNERS / CASSETTE / DISC PLAYERS
MINI
STAN
DIN
ISO DIN
SINGLE
DBL DIN
CHASSIS H
13/ 4-2
2
2
2
37/ 8
3
CHASSIS W
71 / 8
71/ 8
71/ 8
7
71/ 8
71/8
CHASSIS D
43/ 4-51/2
57/ 8-611/ 16
57/ 8-611/ 16
57/ 8-611/ 16
57/ 8-611/ 16
57/ 8-611/ 16
NOSE H
15/ 8-13/4
15/ 8-13/4
23/ 8
113/ 16
33/ 4-4
NOSE W
41/ 8-43/ 16
41/ 8-43/ 16
71/ 2
611/ 16
611/ 16-71/4
SHAFT SP.
51/ 8-53/4
51/ 8-6
UPDATED
THROUGH
'96
'97
'98
'99
MITSUBISHI
1995-UP ECLIPSE
Coupe
IN DASH APPLICATION NOTES
K
K
K
K4
K
K
APPLICATION KIT MODEL:
MI02
HARNESS ADAPTOR:
ANTENNA ADAPTOR:
NONE
IN-DASH INSTALLATION AREA DIMENSIONS
MAX
DEPTH
DEPTH
8"
CAVITY
DASH
OPENING
TYPE:
DASH MATERIAL:
WIDTH
8"
8"
5"
5
DOUBLE ISO DIN
RUBBER COATED PLASTIC
HEIGHT
7 /32"
THICKNESS:
4"
3
/16 "
REMOVE REAR SUPPORT
FOR MAX DEPTH
MODIFY CAVITY
AMPLIFIER/EQ MOUNTING LOCATIONS (WxHxD)
UNDER/IN
DASH
UNDER
SEAT
Various
GLOVE
BOX
TRUNK/
CARGO
Various
NOTE: THIS MANUAL IS BASED ON CAREFULLY DOCUMENTED RESEARCH. ABSOLUTE
ACCURACY IS ATTEMPTED BUT NOT GUARANTEED. USE THIS MANUAL AS A REFERENCE
GUIDE. SCOSCHE, INC. CANNOT BE RESPONSIBLE FOR INCONSISTENCIES THAT MAY OCCUR.
Dimensions shown are inches.
For inch/mm conversions refer to chart section.
B
C1
C2
D
D1
D2
D3
F1
F2
K
K1
K2
K3
K4
=
=
=
=
=
=
=
=
=
=
=
=
=
=
K 5 = WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO/TAPE PLAYER. FABRICATE
KIT WHEN EQUIPPED WITH FLAT FACE ELECTRONIC RADIO/TAPE PLAYER.
K S = SCOSCHE KIT RECOMMENDED.
N = NOT RECOMMENDED. EXTENSIVE MODIFICATION REQUIRED.
P = PERFECT WITHOUT MODIFICATION.
P 1 = MODIFY OR REMOVE POCKETS.
P 2 = COIN POCKET LOCATION IN DASH (MAY REQUIRE TRIM KIT).
P 3 = PERFECT WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO, K WITHOUT.
R = REAR LOAD ISOMOUNT.
U = UNDERDASH.
W 1 = WITH POWER WINDOWS ONLY.
W 2 = WITHOUT POWER WINDOWS ONLY.
BACK UP PLATES REQUIRED.
CUT TRIM/PLASTIC (STRUCTURE).
CUT STEEL.
BELOW DECK ONLY.
LIFT PORTION OF DECK. (MAY REQUIRE STRUCTURAL REINFORCEMENT).
CUT STEEL WHEN TOP MOUNTED. DO NOT IF BELOW DECK.
NARROW SURFACE, BELOW DECK ONLY.
MINIMUM MODIFICATION FILE SHAFT HOLES OR DASH OPENING.
MODIFY DASH CAVITY AND/OR PANEL.
INSTALLATION KIT, SPACER OR ADAPTOR REQUIRED.
KIT MODIFICATIONS REQUIRED.
EXTENSION KIT RECOMMENDED.
WHEN EQUIPPED WITH FACTORY "ELECTRONIC" RADIO.
FABRICATE PANEL/BRACKETS.
181
©
1995-UP MITSUBISHI ECLIPSE
COUPE
DASH.
FRONT DOOR PANEL.
PRELIMINARY: DISCONNECT THE NEGATIVE BATTERY CABLE
3. POP OFF SCREW COVER AND REMOVE THE SCREW BEHIND IT ON THE
LOWER PART OF THE SIDE PANEL.
4. POP OFF SCREW COVER AND REMOVE THE SCREW BEHIND IT NEAR THE
FOLDING SEAT LATCH.
5. PULL MOLDING OFF ALONG THE FRONT OF THE REAR PANEL WHERE THE
DOOR CLOSES.
6. CAREFULLY PULL OUT ON PANEL TO RELEASE PANEL FASTENERS.
7. REMOVE PANEL.
8. EXTRACT (4) SCREWS HOLDING SPEAKER IN, UNPLUG AND REMOVE.
ANTENNA: THE FACTORY POWER ANTENNA (IF EQUIPPED) OR METAL
ROD ANTENNA IS LOCATED ON THE LEFT REAR FENDER.
NOTE: THE VEHICLE MAY ALSO BE EQUIPPEDWITH A DIVERSITY ANTENNA
SYSTEM WITH A MINI STYLE PLUG AT THE BACK OF THE RADIO.
RADIO REMOVAL AND IN-DASH INSTALLATION:
NOTE: THE FACTORY RADIO PROVISION IS FOR A DOUBLE DIN ISO RADIO
OR RADIO/POCKET STACK. AN INSTALLATION KIT IS RECOMMENDED
FOR AFTERMARKET INSTALLATIONS.
1. CAREFULLY PRY OUT ON RADIO/AC CONTROL TRIM BEZEL TO RELEASE
THE SNAP CLIPS.
2. EXTRACTTHE (2) SCREWS FROM BEHIND THE RADIO TRIM BEZEL.
3. POP OUT CUP HOLDER AND ASHTRAY FROM CENTER CONSOLE.
4. EXTRACT THE SCREW FROM UNDERNEATH THE CUP HOLDER AND
ASHTRAY.
5. EXTRACT (2) SCREWS FROM REAR SIDES OF CONSOLE.
6. PULL UP CENTER CONSOLE AND SLIDE BACKWARD ENOUGH TO EXPOSE
ALL (4) OF THE RADIO’S MOUNTING SCREWS.
7. EXTRACT (4) SCREWS HOLDING RADIO IN PLACE, UNPLUG AND REMOVE
RADIO.
FRONT DASH SPEAKER INSTALLATION:
NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 2" TWEETER. THE
TWEETER AND THE GRILLE ARE ONE PIECE AND SNAP INTO TOP
CORNERS OF THE DASH.
1. CAREFULLY PRY UP ON THE EDGE OF THE TWEETER TO RELEASEUNPLUG AND REMOVE.
FRONT DOOR SPEAKER INSTALLATION:
NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 61/2" PIN CUSHION
SPEAKER IN A FACTORY ADAPTOR.
1. POP OFF SCREW COVER FROM BOTTOM OF DOOR PANEL POCKET AND
REMOVE SCREW BEHIND.
2. PULL DOOR RELEASE, AS IF TO OPEN DOOR AND REMOVE THE SCREW
IN THAT CUP.
3. PULL DOOR RELEASE CUP FORWARD AND OUTWARD TO REMOVE IT.
*ON NON-POWER MODELS RELEASE WINDOW CRANK CLIP AND REMOVE
WINDOW CRANK.
4. EXTRACT ONE PHILLIPS SCREW BEHIND THE PLASTIC CUP THAT WAS
JUST REMOVED.
5. POP OFF (2) CAPS AND REMOVE THE (2) SCREWS ATTHE REAR EDGE OF
THE DOOR PANEL.
6. POP OFF (2) CAPS AND REMOVE THE (2) SCREWS AT THE FRONT EDGE
OF THE DOOR PANEL.
7. USING A PANEL REMOVAL TOOL CAREFULLY PRY OUT AROUND THE SIDE
AND BOTTOM EDGES OF THE DOOR PANEL TO RELEASE APPROX (7)
PANEL FASTENERS.
8. PULL PANEL OUTWARD TO RELEASE THE REMAINING (4) FASTENERS AT
THE TOP EDGE OF THE DOOR PANEL BY THE WINDOW.
9. NOW UNPLUG POWER WINDOW/LOCK SWITCHES IF APPLICABLE.
10. REMOVE PANEL.
11. EXTRACT (4) SCREWS HOLDING SPEAKER IN, UNPLUG AND REMOVE
SPEAKER.
REAR SEAT SIDE PANEL.
REAR SEAT SIDE PANEL SPEAKER INSTALLATION:
NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 6 X 9" SPEAKER IN
ADAPTOR.
1. PULL OUT ON (2) RELEASE TABS ALONG THE FRONT EDGE OF THE REAR
SEAT BOTTOM.
2. REMOVE SEAT BOTTOM CUSHION.
TWEETER POPPED OUT DASH.
182
©
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising