2.4 The Horizontal System
USER’S MANUAL
Hantek6022BL
V1.0.1
www.hantek.com
Content
General Safety Summary .............................................................................. 1
Chapter 1 Getting Start.................................................................................. 2
1.1 System Requirement ........................................................................................... 3
1.2 Install Software..................................................................................................... 4
1.3 Install Driver ......................................................................................................... 7
1.4 General Features ................................................................................................11
1.5 General Check ................................................................................................... 12
1.6 Probe Compensation ......................................................................................... 12
1.7 Function Check .................................................................................................. 13
1.8 Self Calibration ................................................................................................... 15
1.9 Accessories ........................................................................................................ 15
Chapter 2 Operating Basics ........................................................................ 16
2.1 The User’s Interface ........................................................................................... 17
2.2 The Menu System .............................................................................................. 19
2.3 The Vertical System ........................................................................................... 21
2.4 The Horizontal System ....................................................................................... 21
2.5 The Trigger System ............................................................................................ 22
2.6 Input Connectors ................................................................................................ 23
Chapter 3 Understanding Function ............................................................ 24
3.1 Set Oscilloscope ................................................................................................ 25
3.2 Set Vertical Systems .......................................................................................... 25
3.3 Set Horizontal System........................................................................................ 31
3.4 Set Trigger System ............................................................................................ 32
3.5 Measure Signal .................................................................................................. 33
3.6 The Utility Function ............................................................................................ 37
3.7 The Display System ........................................................................................... 41
3.8 Save/Load Menu ................................................................................................ 45
3.9 Print ................................................................................................................... 46
Chapter 4 Application Example .................................................................. 47
4.1 Simple Measurement ......................................................................................... 48
4.2 Capturing a Single-Shot Signal .......................................................................... 49
4.3 The Application of the X-Y .................................................................................. 50
4.4 Taking Cursor Measurements ............................................................................ 52
Chapter 5 Instructions of Hantek6022BL ................................................... 54
5.1 The User’s Interface ........................................................................................... 55
5.2 The Menu System .............................................................................................. 56
5.3 The Tool Bar ....................................................................................................... 58
5.4 The Control Panel .............................................................................................. 59
5.5 The Status bar .................................................................................................... 59
5.6 The Output Window ........................................................................................... 60
5.7 Input Connector: ................................................................................................ 61
5.8 The Measurement .............................................................................................. 61
Appendix ...................................................................................................... 62
Appendix A: Specification ........................................................................................ 63
Appendix B: General Maintenance .......................................................................... 65
Hantek 6022BL
General Safety Summary
Review the following safety precautions carefully before operate the device to avoid any
personal injuries or damages to the device and any products connected to it. To avoid
potential hazards use the device as specified by this user’s guide only.
‹
To Avoid Fire or Personal Injury
‹
Use Proper Power Cord. Use only the power cord specified for this product and
certified for the country of use.
‹
Connect and Disconnect Properly. Do not connect or disconnect probes or test
leads while they are connected to a voltage source.
‹
Connect and Disconnect Properly. Connect the probe output to the measurement
device before connecting the probe to the circuit under test. Disconnect the probe
input and the probe reference lead from the circuit under test before disconnecting
the probe from the measurement device.
‹
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
‹
Use Proper Probe. To avoid shock hazard, use a properly rated probe for your
measurement.
‹
Avoid Circuit or Wire Exposure. Do not touch exposed connections and
components when power is on.
‹
Do Not Operate With Suspected Failures. If suspected damage occurs with the
device, have it inspected by qualified service personnel before further operations.
‹
Provide Proper Ventilation. Refer to the installation instructions for proper
ventilation of the device.
‹
Do not operate in Wet/Damp Conditions.
‹
Do not operate in an Explosive Atmosphere.
‹
Keep Product Surfaces Clean and Dry.
User’s Manual
1
Hantek 6022BL
Chapter 1 Getting Start
The oscilloscope is small, lightweight, no external power required, portable oscilloscopes!
The oscilloscopes is ideal for production test, research and design and all of the
applications involving analog circuits test and troubleshooting, as well as education and
training.
In addition to the list of general features on the next page, this chapter describes how to
do the following tasks:
‹
System Requirements
‹
Install software
‹
Install driver
‹
General Features
‹
General Check
‹
Probe compensation
‹
Functional Check
‹
self calibration
‹
Accessories
User’s Manual
2
Hantek 6022BL
1.1 System Requirement
To run the oscilloscope software, the needs of computer configuration are as follows:
Minimum System Requirements
Operating System
Window XP/Vista/Win7/Win8
Processor
Upwards of 1.00G processor
Memory
128M byte
Disk Space
500M disk free space
Screen resolution
800 x 600
Recommended Configuration
Windows XP SP2 System
2.4G Processor
512M Byte Memory
80G Disk Space
1024 x 768 or 1280 x 1024 resolution
DPI Setting: Normal Size (96DPI)
User’s Manual
3
Hantek 6022BL
1.2 Install Software
Caution: You must install the software before using the oscilloscope.
1.
While in Windows, insert the installation CD into the CD-ROM drive.
2.
The installation should start up automatically. Otherwise in Windows Explorer, switch
to the CD-ROM drive and run Setup.exe.
3.
The software Installation is started. Click 'Next' to continue.
User’s Manual
4
Hantek 6022BL
4.
Choose a destination directory. Click 'Next' to continue.
5.
Check the setup information. Click Next to start copying of files.
User’s Manual
5
Hantek 6022BL
6.
This Status dialog is displayed during copying of files.
7.
Updating Your System Configuration.
8.
The installation is complete.
User’s Manual
6
Hantek 6022BL
1.3 Install Driver
1.
Connect the A-Type Plug of USB cable to your PC’S USB port.
2.
Connect the B-Type Plug of USB cable to USB port.
3.
New hardware is found.
4.
New hardware search wizard starts.
User’s Manual
7
Hantek 6022BL
5.
New hardware search wizard starts to search the driver.
6. New hardware wizard installs “DRIVER”.
User’s Manual
8
Hantek 6022BL
7.
The wizard has finished installing for “DRIVER”.
8.
New hardware is found.
User’s Manual
9
Hantek 6022BL
9. Found new hardware Wizard. Select “Install the software automatically”.
10. New hardware wizard installs software and finish new hardware search wizard.
User’s Manual
10
Hantek 6022BL
11. Your new hardware is installed and ready to use.
1.4 General Features
‹
Maximum real-time sample rate: 48MSa/s
‹
Memory depth: 1Mbytle/channel
‹
Built-in Fast Fourier Transform function(FFT);
‹
20 Automatic measurements;
‹
Automatic cursor tracking measurements;
‹
Waveform storage;
‹
User selectable fast offset calibration;
‹
Add, Subtract , Multiply and Division Mathematic Functions;
‹
Adjustable waveform intensity, more effective waveform view;
‹
User interface in several user-selectable languages;
User’s Manual
11
Hantek 6022BL
1.5 General Check
Please check the instrument as following steps after receiving an oscilloscope:
‹
Check the shipping container for damage:
Keep the damaged shipping container or cushioning material until the contents of the
shipment have been checked for completeness and the instrument has been checked
mechanically and electrically.
‹
Check the accessories:
Accessories supplied with the instrument are listed in "Accessories" in this guide. If
the contents are incomplete or damaged,please notify the franchiser.
‹
Check the instrument:
In case there is any mechanical damage or defect, or the instrument does not operate
properly or fails performance tests, please notify the franchiser.
1.6 Probe Compensation
Perform this function to match the characteristics of the probe and the channel input.
This should be performed whenever attaching a probe to any input channel at the first
time.
‹
From the “Probe” menu, select attenuation to 1:10. Set the switch to “X10” on the
probe and connect it to CH1 of the oscilloscope. When using the probe hook-tip,
insert the tip onto the probe firmly to ensure a proper connection.
‹
Attach the probe tip to the Probe Compensator and the reference lead to the
ground connector, select CH1, and then press the “AUTOSET“ button into the
menu or the toolbar.
‹
Check the shape of the displayed waveform.
Correctly Compensated
User’s Manual
12
Hantek 6022BL
Over compensated
Under Compensated
■ If necessary, use a non-metallic tool to adjust the trimmer capacitor of the probe for
the fattest square wave being displayed on the oscilloscope.
■ Repeat if necessary.
WARNNING: To avoid electric shock while using the probe, be sure the perfection of the
insulated cable, and do not touch the metallic portions of the probe head while it is
connected with a voltage source.
1.7 Function Check
Perform this functional check to verify that your oscilloscope is operating correctly.
‹
Connect the oscilloscope
You should connect the A-Type Plug of USB cable to your PC USB port and connect
the B-Type Plug of USB cable to oscilloscope USB port.
User’s Manual
13
Hantek 6022BL
‹
Input a signal to a channel of the oscilloscope
The oscilloscope is equipped with dual channels.
Please input signal in the following steps:
Set the attenuation switch on the probe as 10X and connect the probe on the oscilloscope
with CH1. Aim the slot in the probe connector at the faucet on BNC of CH1 and insert,
then, turn right to lock the probe. Finally, attach the tip of probe and ground nip to the
Connector of Probe compensator.
1.
Set the CH1 probe attenuation of the oscilloscope to X10. (The default is X1).
2.
Attach the tip of probe and ground nip to the Connector of Probe compensator. A
square wave will be displayed within a several seconds. (Approximately 1 kHz,
2V, peak- to- peak).
3.
Inspect CH2 with the same method. Repeat steps 2 and 3.
User’s Manual
14
Hantek 6022BL
1.8 Self Calibration
The self calibration routine lets you optimize the oscilloscope signal path for maximum
measurement accuracy. You can run the routine at any time but you should always run the
routine if the ambient temperature changes by 5℃ or more. For accurate calibration,
power on the oscilloscope and wait twenty minutes to ensure it is warmed up. To
compensate the signal path, disconnect any probes or cables from the input connectors.
Then, access the “Menu -> Utility -> Calibration” option and follow the directions on the
screen. The self calibration routine takes about several minutes.
1.9 Accessories
All the accessories listed below are standard accessories for the oscilloscope:
‹
Probe×2 (1.5m), 1:1, (10:1) Passive Probes
‹
A USB Cable
‹
A PC software CD of the oscilloscope
User’s Manual
15
Hantek 6022BL
Chapter 2 Operating Basics
‹
The User’s Interface
‹
The Menu System
‹
The Vertical System
‹
The Horizontal System
‹
The Trigger System
‹
Input Connector
User’s Manual
16
Hantek 6022BL
2.1 The User’s Interface
Click the software icon
on the desk after you finished the software setting
and equipment connecting. Then click icon
to run Hantek6022BE mode.
In addition to displaying waveforms, the display area is filled with many details about the
waveform and the oscilloscope control settings.
1.
The Main Menu
All settings can be found in the main menu.
2.
The Toolbar
3.
Control Panel
4.
The Horizontal Panel
The user can change Time/Div, format in the panel.
5.
The Vertical Panel
The user can turn on/off the CH1/CH2. Also the user can change the CH1/CH2
User’s Manual
17
Hantek 6022BL
volt/div, coupling and probe attenuation.
6.
The Trigger Panel
In this panel, the user can change the trigger mode, sweep, source and slope.
7.
Displays the system time.
8.
Displays Sample Rate
9.
Displays the main time base setting.
10. Displays the CH2 information
Readouts show the coupling of the channels.
Readouts show the vertical scale factors of the channels.
A “B” icon indicates that the channel is bandwidth limited.
11. Displays the CH1 information
Readouts show the coupling of the channels.
Readouts show the vertical scale factors of the channels.
12. Displays Output Window
13. The markers show the reference points of the displayed waveforms. If there is
no marker, the channel is not displayed.
14. The same as 13.
15. Measure Window.
User’s Manual
18
Hantek 6022BL
2.2 The Menu System
The Main Menu of Hantek6022BE:
1.
File: Load or Save data, setup
2.
View: Change the user interface
3.
Horizontal: Set the horizontal system
4.
Vertical: Set the vertical system
User’s Manual
19
Hantek 6022BL
5.
Trigger: Set the trigger system
6.
Display: The waveform display setup
7.
Cursor: Cursor measure setup
8.
Utility: Utility setting
9.
Help: Turn on help file
User’s Manual
20
Hantek 6022BL
2.3 The Vertical System
Click “Vertical” in main menu
The following figure shows the vertical system menu. It shows the vertical parameters
setting.
1.
CH1: Leads to the setting of the CH1 parameters
2.
CH2: Leads to the setting of the CH2 parameters
Use the left mouse button to dragging the channel icon to set the vertical position offset
precisely.
2.4 The Horizontal System
Click “Horizontal” in main menu
The following figure shows the Horizontal System window. It shows the horizontal
parameters settings.
1.
Time/DIV: leads the setting of the time base parameters
2.
Format: leads the setting of the horizontal format parameters
The time base ranges of the oscilloscope is listed as follows. The horizontal scan speed is
from 4ns/div to 1hour/div.
In the “Format” menu of the “Horizontal” menu, select the display mode to Y-T, X-Y.
User’s Manual
21
Hantek 6022BL
2.5 The Trigger System
Click “Trigger” in main menu.
Mode: Sets the trigger mode to Edge trigger
Sweep: Selects the trigger sweep mode to AUTO, NORMAL or SINGLE
Source: Selects the trigger source to CH1, CH2.
Slope: Selects the edge trigger slope to Positive or Negative slope
The user can drag the trigger icon to adjust the trigger level and the trigger level will be
displayed on the top right corner.
User’s Manual
22
Hantek 6022BL
2.6 Input Connectors
Input Connectors:
1
2
1. Button: press the button down to run hantek6022BE software.
2. USB PORT: Connect the B-Type Plug of USB cable to this port.
CH 1/CH 2: Input connectors for waveform display.
GND.: a ground terminal
CAL.: Probe compensation output.
User’s Manual
23
Hantek 6022BL
Chapter 3 Understanding Function
‹
Set Oscilloscope
‹
Set Vertical System
‹
Set Horizontal System
‹
Set Trigger System
‹
Measure Signal
‹
Utility Function
‹
The Display System
‹
Save/Load
‹
Print
User’s Manual
24
Hantek 6022BL
3.1 Set Oscilloscope
Save Setup
The oscilloscope software saves the current setup before you close the oscilloscope
software. The oscilloscope recalls this setup the next time you run the software. You can
use the “Save Setup” menu to permanently save up to several different setups.
Load Setup
The oscilloscope can recall the last setup before the oscilloscope software was running,
any saved setups, or the factory setup. You can use the “Load Setup” menu to
permanently recall a setup.
Factory Setup
The oscilloscope software is set up for normal operation when it is shipped from the
factory. This is the factory setup. To recall this setup, push the “Factory Setup” menu.
3.2 Set Vertical Systems
Click “Vertical” in main menu
The Vertical Menu function:
‹
Turn ON/Off:
Turn on/off the channel
‹
Volt/DIV:
Select the channel voltage/div
‹
Invert:
Turns the displayed waveform 180 degrees
¾ Change Volt/DIV
You can click “Volt/Div” in “CH1/CH2” Menu to select the voltage
You can also change “CH1/CH2” voltage in sidebar
User’s Manual
25
Hantek 6022BL
You can left click and drag the mouse on the green knob or the yellow knob to change the
voltage.
¾ Probe Attenuation Setting
Select the attenuation factor for the probe. To check the probe attenuation setting, toggle
the probe menu to match the attenuation factor of the probe.
This setting remains in effect before you changed again.
The probe setting window in the sidebar:
Note: The attenuation factor changes the vertical scale of the oscilloscope so that the
measurement results reflect the actual voltage levels at the probe tip.
¾ Invert
The invert function turns the displayed waveform 180 degrees, with respect to the ground
level. When the oscilloscope is triggered on the inverted signal, the trigger is also inverted.
Click “Invert” in vertical.
User’s Manual
26
Hantek 6022BL
Turn off invert
Turn on invert
The following picture shows the waveform before inversion:
The following picture shows the waveform of inversion:
User’s Manual
27
Hantek 6022BL
3.2.1 Set Math
Click
in Toolbar.
The MATH Menu:
‹
Turn On/Off:
Turn On/Off the MATH Channel.
‹
Source A/B:
Set the sources of the math channel.
‹
Operate:
Set operates type of the math channel.
The mathematic functions include addition, subtract, multiply and division for CH1 and
CH2.
¾
Operate
Four Types:
A+B
Add source A and source B
A-B
Subtract source B from source A
A×B
Multiply source A by source B
A/B
Division source A by source B
In this function, use the addition, subtraction, multiplication and division function to
operate and analyze the waveform.
Select the operate type in the Operate menu. Select source A and B. Then adjust the
vertical scale and offset to view the math channel clearly. The mathematic result can be
measured by the measure and the cursor.
User’s Manual
28
Hantek 6022BL
The Math Function Display:
Fast Fourier Transform Function
To use the FFT mode, you need to click
in Toolbar to open the FFT setup window.
The FFT setup window:
You can select the Source channel, Window algorithm, FFT number, and FFT Zoom
User’s Manual
29
Hantek 6022BL
factor. It displays only one FFT spectrum at a time.
Source:
Selects the channel used as the FFT source
Window:
Selects the FFT window type
Scale:
Selects the vertical scale units
Vert Scale:
Selects the vertical scale
HORI Scale:
Selects the FFT zoom factor
Sets horizontal scale, If the information is more than the quantity displayed to the display
window, more information is displayed by using scroll bar.
You can click the “ON/OFF” button to start FFT math, also you can click this button to stop
FFT math.
3.2.2 Set Reference
Click “
” in Toolbar to set REF.
The Reference Channel Function:
‹
Turn On/Off:
Turn on/off the reference channel.
‹
Volt/DIV:
Channel the resolution of the reference channel.
‹
Time/DIV:
leading the setting of the time base parameters.
You can change the vertical scale of a waveform. The waveform display will contract or
expand relative to the reference level.
User’s Manual
30
Hantek 6022BL
The Reference Waveform Display Window:
Note: If you turn on the “Reference” channel, the load file window will appear.
3.3 Set Horizontal System
The following figure shows the Horizontal System window. It shows the horizontal
parameters settings.
1.
Time/DIV: leads the setting of the time base parameters
2.
Format: leads the setting of the horizontal format parameters
The time base ranges of the oscilloscope is listed as follows. The horizontal scan speed is
from 4ns/div to 1hour/div.
User’s Manual
31
Hantek 6022BL
In the “Format” menu of the “Horizontal” menu, select the display mode to Y-T, X-Y.
3.4 Set Trigger System
Click “Trigger” in main menu.
The trigger determines when the oscilloscope starts to acquire data and display a
waveform. When a trigger is set up properly, it can convert unstable displays or blank
screens into meaningful waveforms.
If the oscilloscope wants to acquire a waveform, it collects enough data so that it can draw
the waveform to the left of the trigger point. The oscilloscope continues to acquire data
while waiting for the trigger condition to occur. The oscilloscope continues to acquire
enough data so that it can draw the waveform to the right of the trigger point after it
detects a trigger.
The Edge trigger determines whether the oscilloscope finds the trigger point on the rising
or the falling edge of a signal. Select Edge trigger mode to trigger on Rising edge or
Falling edge.
Mode: Select the trigger mode.
The oscilloscope only provides edge trigger mode.
Sweep: Set the sweep mode to Auto, Normal or Single.
Auto: Acquire waveform even no trigger occurred
Normal: Acquire waveform when trigger occurred.
Single: Acquire waveform when trigger occurred then stop
User’s Manual
32
Hantek 6022BL
Source: You can use the trigger source options to select the signal that the oscilloscope
uses as a trigger.
CH1: Select CH1 as trigger signal
CH2: Select CH2 as trigger signal
Slope: Set the slope to Rising (+) or Falling (-).
Rising: Trigger on rising edge
Falling: Trigger on falling edge
3.5 Measure Signal
3.5.1 Cursor
Click “Cursor” in main menu.
This method allows you to take measurements by moving the cursors
1.
Source
The user can set the source to CH1, CH2.
2.
Type
There are four types of cursors: Cross, Vertical and Horizontal.
User’s Manual
33
Hantek 6022BL
1)
Cross
The Cross cursors appear as cross lines on the display and measure the vertical and
horizontal parameters.
The Cross cursor display window:
2)
Vertical
The Vertical cursors appear as vertical lines on the display and measure the vertical
parameters.
The Vertical cursor display window:
User’s Manual
34
Hantek 6022BL
3)
Horizontal
The Horizontal cursors appear as horizontal lines on the display and measure the
horizontal parameters.
The Horizontal cursor display window:
3.5.2 Measure
Click “Measure” in main menu.
The oscilloscope provides 20 parametric auto measurements (12 voltage and 8 time
measurements).
1.
Vertical
User’s Manual
35
Hantek 6022BL
Maximum: Voltage of the absolute maximum level, Measured over the entire waveform
Minimum: Voltage of the absolute minimum level, Measured over the entire waveform
Peak To Peak: Peak-to-peak = Max – Min, Measured over the entire waveform
Top: Voltage of the statistical maximum level, Measured over the entire waveform
Base: Voltage of the statistical minimum level, Measured over the entire waveform
Middle: Voltage of the 50% level from base to top
RMS: The Root Mean Square voltage over the entire waveform
Amplitude: Amp = Base – Top, Measured over the entire waveform
Mean: The arithmetic mean over the entire waveform
Cycle Mean: The arithmetic mean over the first cycle in the waveform
Preshoot: Positive Overshoot = (Max - Top)/Amp x 100 %, Measured over the entire
waveform
Overshoot: Negative Overshoot = (Base - Min)/Amp x 100 %, Measured over the entire
waveform
2.
Horizontal
Period: Time to take for the first signal cycle to complete in the waveform
Frequency: Reciprocal of the period of the first cycle in the waveform
Rise Time: Time taken from lower threshold to upper threshold
Fall Time: Time taken from upper threshold to lower threshold
+Duty Cycle: Positive Duty Cycle = (Positive Pulse Width)/Period x 100%, Measured of
the first cycle in waveform
-Duty Cycle: Negative Duty Cycle = (Negative Pulse Width)/Period x 100%, Measured of
the first cycle in waveform
+Pulse Width: Measured of the first positive pulse in the waveform. The time between the
50% amplitude points
-Pulse Width: Measured of the first negative pulse in the waveform. The time between the
50% amplitude points
3.
Clear Measure
Clear all measure items on display screen.
User’s Manual
36
Hantek 6022BL
The Measure Display Window:
Note: The results of the automatic measurements will be displayed on the bottom of the
screen. Maximum 8 results could be displayed at the same time. When there is no room,
the next new measurement result will make the previous results moving left, out of screen.
3.6 The Utility Function
Click the “Menu -> Utility” to get into the “Utility” menu.
The “Utility” Functions:
‹
Default Setup
User’s Manual
37
Hantek 6022BL
‹
Interpolation
‹
Language
3.6.1 Default Setup
Click “Default Setup” in “Utility” menu to load default setups
When you click the Default Setup in Utility menu, the oscilloscope displays the CH1 and
CH2 waveforms and removes all other waveforms.
The oscilloscope set up for normal operation when it is shipped from the factory and can
be recalled at anytime by user.
The Factory Setup function does not reset the following settings:
‹
Language option
‹
Date and time
3.6.2 Language
Click “Language” in “Utility” menu.
There are four languages in “Language” menu. The default language is English.
At the time base 40ns/div or faster, user can use the 3 different interpolation mode to get
waveforms of different smoothness.
User’s Manual
38
Hantek 6022BL
3.6.3 Interpolation
Click “Utility->Interpolation”.
The Step Interpolation:
User’s Manual
39
Hantek 6022BL
The Linear Interpolation:
The Sin(x)/x Interpolation:
Note: The default interpolation mode is Sin(x)/x.
User’s Manual
40
Hantek 6022BL
3.7 The Display System
Click “Display” in main menu.
The following figure shows the display system menu. Displays parameters setting.
‹
Type
‹
Grid
‹
Intensity
3.7.1 Type
Click “Type” in “Display” menu.
If the Vectors type mode is selected, the waveform will be displayed as following figure.
User’s Manual
41
Hantek 6022BL
If the Dots type mode is selected, the waveform will be displayed as following figure.
3.7.2 Grid
Click “Display” in main menu.
User’s Manual
42
Hantek 6022BL
The grid shows:
Without the grid show:
User’s Manual
43
Hantek 6022BL
3.7.3 Intensity
Click “Display->Intensity” in main menu
The following figure shows the intensity dialog. It shows the display parameters setting.
You can change the grid and waveform color intensity in this dialog.
User’s Manual
44
Hantek 6022BL
3.8 Save/Load Menu
Click “File” in main menu to save waveform, setups and screen
1.
Save Data
Save waveform data
2.
Save Setups
Save the current oscilloscope setups to file
Load Menu
Click “File” in main menu to recall saved waveform, setup
1.
Load Data
Load the waveform
2.
Load Setup
Load the instrument that had saved
User’s Manual
45
Hantek 6022BL
3.9 Print
Click “Print” in File.
1.
2.
Click “Print” in “File” menu to set the printer to print the current waveform.
Click the “PrintPreview” in “File” menu to get into the Preview window.
In “PrintPreview” window, use the
button to change the size of the waveform
graph. Click the “Close” button to turn this window off and click the “Print” button to print
the report.
User’s Manual
46
Hantek 6022BL
Chapter 4 Application Example
‹
Simple Measurement
‹
Capturing a Single-Shot Signal
‹
The Application of the X-Y
‹
Taking Cursor Measurement
User’s Manual
47
Hantek 6022BL
4.1 Simple Measurement
To acquire and display a signal, please do the steps as follows:
Connect signal to CH1 by using probe
The oscilloscope set the vertical, horizontal, and triggers controls at the best status
automatically. Also, you can adjust the controls to meet your measurement to optimize the
waveform display.
1.
To measure the frequency and “Vpp”, you can do these steps as follows:
2.
Click the
button, the frequency of the signal display on the bottom of
the waveform interface.
3.
Click the
button, the “Vpp” of the signal will also display on the
bottom of the waveform interface.
4.
To clear the measurement on the waveform interface, click the
User’s Manual
button.
48
Hantek 6022BL
The results of measure display in Information output.
4.2 Capturing a Single-Shot Signal
To capture a single event, it needs to gather some pre-test knowledge of the signal in
order to set up the trigger level and slope correctly. For example, if the event is derived
from 3.3V COMS logic, a trigger level of 1.2 or higher Volts should work on a rising edge.
Do these steps as follows:
1.
Set the probe and the channel attenuations to X 10.
2.
Set up the trigger in the Trigger Menu, or in the Trigger Setting window.
1)
Adjust the Trigger Mode to Edge.
2)
Set the Trigger Sweep to Single.
3)
Set the Trigger Source to CH1.
4)
Set the Trigger Slope to “+” which means you select the rising edge.
5)
Adjust the Volts/Div and the time base in a proper range for the signal.
6)
Drag the trigger level sign on the waveform display screen to proper position. It’s
User’s Manual
49
Hantek 6022BL
usually higher a little above the normal level.
7)
When the trigger conditions are met, data appears on the display representing
the data points that the oscilloscope obtained with one acquisition.
4.3 The Application of the X-Y
X-Y Plot acts to analyze correlation of data of two channels. Lissajous diagram is
displayed in the screen when you use X-Y Plot, which enables to compare frequencies,
amplitudes and phases of counterpart waveform against the reference waveform. This
makes it possible to compare and analyze frequency, amplitude and phase between input
and output.
Do these steps as follows:
1.
Set the probe attenuation to “x10”. Set the switch to “x10” on the probes.
2.
Connect the CH1 probe to the input of the circuit, and connect the CH2 probe to the
output of the circuit.
3.
Adjust the vertical scale and offset to display approximately the same amplitude
signals on each channel.
4.
Select X-Y format at Horizontal window. The oscilloscope will displays a Lissajous
pattern representing the input and the output characteristics of the circuit.
5.
Adjust the scale and offset of the horizontal and vertical to a desirable waveform
display. The following picture shows a typical example.
6.
Apply the Ellipse Method to observe the phase difference between the two channels.
Signal in X-Y Format:
Instruction of the Ellipse Method
User’s Manual
50
Hantek 6022BL
Sinθ = A/B or C/D, where θ = phase shift (in degrees) between the two signals.
From the formula above:
θ = ±arcsine (A/B) or ±arcsine (C/D)
θ must be in the range of (0~π/2) or (3π/2~2π) if the main axis of the ellipse is between I
and III quadrant, . If the main axis is at II and IV quadrant, θ must be in the range of
(π/2~π) or (π~3π/2).
User’s Manual
51
Hantek 6022BL
4.4 Taking Cursor Measurements
Use cursors to make time and amplitude measurements on a waveform quickly.
Measure the Peak Frequency or Time of the First Sine Waveform
Do these steps:
1.
Click “Cursor->Source”, select CH1 (select CH2 if you want measure CH2).
2.
Click “Cursor->Type”, select Vertical.
3.
Push left mouse button, and the vertical lines appear.
4.
Drag the mouse button to the point you want to measure.
5.
Release the left mouse button, the frequency difference and time difference will be
shown at the status bar.
Measure the Amplitude of the First Waveform Peak of the Waveform
Do these steps:
1.
2.
3.
4.
5.
Click “Cursor->Source”, select CH1 (select CH2 if you want measure CH2).
Click “Cursor->Type”, select Horizontal.
Push left mouse button, and the Horizontal lines appear.
Drag the mouse button to the point you want to measure.
Release the left mouse button, the voltage difference will be shown at the status bar.
User’s Manual
52
Hantek 6022BL
Note: Click “Cursor->Type”, select “Cross”, you can measure time and amplitude at one
time.
User’s Manual
53
Hantek 6022BL
Chapter 5 Instructions of Hantek6022BL
‹
The User’s Interface
‹
The Menu System
‹
The Toolbar
‹
The Control Panel
‹
The Status Bar
‹
Input Output Window
‹
Measurement
User’s Manual
54
Hantek 6022BL
5.1 The User’s Interface
Click the software icon
on the desk after you finished the software setting
and equipment connecting. Click icon
to run Hantek6022BL mode.
2
1
3
5
6
4
In addition to displaying waveforms, the display area is filled with many details about the
waveform and the logic analyzer control settings.
1. The Main Menu
All settings can be found in the main menu.
2. The Toolbar
3. Control Panel
The user can change sampling rate in the panel.
4. It shows the system time.
5. It shows the device’s state.
6. Output Window
User’s Manual
55
Hantek 6022BL
5.2 The Menu System
The Main Menu:
1. File: Load or Save data, setup
z
Export As CSV File: Export data to file as “CSV”
z
Export As TXT File: Export data to file as “TXT”
z
Export As BMP File: Export data to file as “BMP”
z
Print…: Print the current waveform
z
Print Preview: Preview the current waveform
z
Print Setup: Setup print type
z
Exit: Exit Hantek6022BL
2. View: Change the user interface
z
Docking Window: show window or not
User’s Manual
56
Hantek 6022BL
z
Status Bar:
show status bar or not
z
Application Look: show style, blue, black, silver or aqua style.
3. Display: The waveform display setup
z
Zoom in: Enlargement waveform view
: User can do the same thing by scrolling the mouse wheel down.
z
Zoom out: Reduction waveform view
: User can do the same thing by scrolling the mouse wheel up.
Zoom all: Show entire waveform view
4. Cursor: Cursor measure setup
z
Source: cursor measure source, CH0 to CH15
z
Type :
show cursor or not
None : cancel the measurement
Vertical: show the measurement
5. Help: Turn on help file
User’s Manual
57
Hantek 6022BL
5.3 The Tool Bar
The following figure shows the tool bar
1.
Export As CSV File: Export data to file as “CSV”
2.
Export As TXT File: Export data to file as “TXT”
3.
Export As BMP File: Export data to file as “BMP”
4.
Print…: Print the current waveform
5.
Print Preview: Preview the current waveform
6.
Print Setup: Setup print type
7.
Zoom In:
8.
Zoom Out: try it by yourself to see it
9.
Zoom All : show waveform With appropriate size
try it by yourself to see it
10. Cursor : Measurement
11. None : Cancel the measurement
12. About : About Information
13. Capture: capture waveform one time
User’s Manual
58
Hantek 6022BL
5.4 The Control Panel
The following figure shows the Control Panel. It shows the control parameters settings.
1.
Hantek6022BL(1.0.1): Name and version information of the software.
2.
Sample length: the length of sample points.
3.
Sample Rate: the sampling rate
5.5 The Status bar
The following figure shows the status bar. It shows the status bar parameters settings.
1
1.
Connected the equipment or not
2.
Time now
User’s Manual
2
59
Hantek 6022BL
5.6 The Output Window
The following figure shows the Output Window. It shows the output window settings.
1
2
3
1.
Channel Name
2.
Time Scale
3.
Waveform
3
User’s Manual
60
Hantek 6022BL
5.7 Input Connector:
1
2
1.
Button: press the button down to run hantek6022BL software.
2.
Pins : connect peripheral equipment
5.8 The Measurement
The following figure shows the Measurement
1.
Click the button of cursor, you can see the picture
z
Time : the time of the two measurement line
z
Frequency: the frequency of the two measurement line
z
Transition : the transition of the two measurement line
z
Cycles : the cycles of the two measurement line
2.
Click on the mouse in the position of trying to start the measurement
3.
Move the mouse to the position fo trying to end the measurement
User’s Manual
61
Hantek 6022BL
Appendix
‹ Appendix A: Specifications
‹ Appendix B: General Maintenance
User’s Manual
62
Hantek 6022BL
Appendix A: Specification
Specifications Table:
Oscilloscope Features(Hantek6022BE)
Input
Max. sample rate
Real-time sampling:48MS/s
Channels
2 Channels
Bandwidth
20MHz (-3dB)
Vertical resolution
8 bits/channel
Gain range
20mV~5V/div@x1 probe(20mV,50mV,100mV,200mV,
500mV,1V,2V,5V/div 1,2,5 sequence)
200mV~50V/div@x10 probe
2V~500V/div@x100 probe
20V~5KV/div@x1000 probe
Range
8 divisions
Offset level
+/-4 divisions
Coupling
DC
Offset increments
0.02 div
Impedance
1M ohm
DC accuracy
+/-3%
Max. Input
+/- 5V
Input protection
35Vpk(Without external attenuation DC + peak AC < 10kHz)
Display mode
Y-T, X-Y
Timebase
Timebase range
Range
Buffer Size
1ns/div~5000s/div(1ns,2ns,5ns,10ns,20ns,50ns,100ns,200ns,
500ns,1us,2us,5us,10us,20us,50us,100us,200us,500us,
1ms,2ms,5ms,10ms,20ms,50ms,100ms,200ms,500ms,1s,2s,
5s,10s,20s,50s,100s,200s,500s,1000s,2000s,5000s/div 1,2,5
sequence)
10 divisions
MAX.1M samples
Trigger
Type
Edge trigger: Rising edge, Falling edge
Mode
Auto, Normal and Single
Autoset
Yes
Range
8 divisions
Trigger level
+/-4 divisions
Settabillity
0.02 div increments
Math
Measurements
User’s Manual
Vp-p, Vmax, Vmin, Vmean, Vrms, Vamp, Vtop, Vbase,
63
Hantek 6022BL
Vmid,positive overshoot, negative overshoot, cycle mean, cycle
RMS, period, frequency, positive pulse width, negative pulse
width, rise time (10%~90%), fall time (10%~90%), positive duty
cycle, negative duty cycle
Math
Addition, Subtraction, Multiplication, Division
FFT
Rectangular, Hanning, Hamming, Blackman Window
Logic Analyzer Features(Hantek6022BL)
Channel
16
Max. Impendance
1MΩ(C=7.5pF)
Max. Voltage
0V~5.5V
Max. Sample
48M
Bandwidth
10MHz
Compatible Input
TTL, LVTTL, CMOS
Memory Depth
1M/CH
General Features
Interface
Universal Serial Bus(USB 2.0)
Demension
No external power source required.
Bus-powered from USB
200mm x100mm x 35mm
Weight
0.3KG
Standard Probe
2 x PP-80
Power
User’s Manual
64
Hantek 6022BL
Appendix B: General Maintenance
General Care
Do not store or leave the oscilloscope where the device will be exposed to direct sunlight
for long periods of time.
Caution
To avoid damages to the device or probes, do not expose them to sprays, liquids or
solvents.
To avoid damages to the surface of the device or probes not use any abrasive or chemical
cleaning agents.
Cleaning
Inspect the device and probes as often as operating conditions require. Make sure the
device disconnect form all power sources.
To clean the exterior surface, perform the following steps:
1.
Remove loose dust on the outside of the oscilloscope and probes with a lint-free cloth.
Use care to avoid scratching the clear glass display filter.
2.
Use a soft cloth dampened with water to clean the device.
User’s Manual
65
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising