ADS-AL(TB)-PR_20090731
Automotive Data Solutions Inc.
INSTALL GUIDE
ADS-AL(TB)-PR
PR
Available for : ADS-AL-CA
Rev. Date: December 07, 2009
Doc. No.: ##2096##
20090731
Version FRançaise disponible en ligne au www.idatalink.com
please visit www.idatalink.com/support for complete product details
The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. © 2009
PRELUDE
!
RL
NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from
improper installation of this product, be that either damage to the vehicle itself or to the installed
device. This device must be installed by a certified technician. This guide has been written for
properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please
review the Installation Guide carefully before beginning any work.
Transponder Bypass
install guide
Honda Prelude/Acura RL
USE THE
FOLLOWING
LAYER au
SPECIFIC
ITEMS AS
Guides
Français disponibles
www.idatalink.com
WIRING AND TEXT TEMPLATES
ADS-AL(TB)-PR
Page 2 of 4
20090731
Doc. No.: ##2096##
type 1 - Wiring diagram
Located near
steering column
LEGEND
Wiring connections not required
when installed in iDatalink mode
* Wiring connection not required in
2-way iDatalink
IMMOBIL
IZER
A
CONNECT EITHER
IDATALINK OR
STANDARD WIRING
IDATALINK (RS232) PORT REQUIRED
ON REMOTE STARTER. IF UNAVAILABLE
USE STANDARD WIRING METHOD
B
IDATALINK
WHITE/BLACK - GROUND
WHITE/RED (NC)
WHITE - STARTER ENABLE
YELLOW/BLACK (NC)
YELLOW/RED (NC)
YELLOW (NC)
GROUND-OUT WHEN RUNNING - BLUE/WHITE
(NC) - NO WIRE
GROUND - BLACK
12V - RED
(NC) GREEN/BLACK
(NC) BLUE/BLACK
(NC) RED/WHITE
(NC) BROWN
(NC) PURPLE/YELLOW
(NC) PURPLE/BLACK
(NC) WHITE
(NC) BLACK/WHITE
(NC) GREEN
(NC) PURPLE/WHITE
REMOTE
STARTER
Honda
Acura
2
5
7
BLUE/RED (NC)
BLUE/YELLOW (NC)
GREEN/RED (NC)
GREEN/YELLOW (NC)
GRAY/RED - DATA OUT
GRAY/YELLOW (NC)
Vehicle
Make
1
BROWN/RED (NC)
BROWN/YELLOW (NC)
ORANGE/BLACK (NC)
ORANGE/WHITE (NC)
ORANGE (NC)
PINK/BLACK - IGNITION OUT IMMOBILIZER SIDE
PINK - IGNITION IN ECM SIDE
Model
Wire Colors
Years
PIN
Ignition
WIRE
PIN Starter
enable
PIN
DATA WIRE
PIN GROUND
Prelude ( Early Production )
1997
4
Black/Yellow
3
Light Blue
6
Brown/Yellow
8
Black
Prelude
1997-01
4
Yellow/Black
3
Light Blue
6
Brown/Yellow
8
Black
RL
1998-04
4
Yellow/Black
3
White/Red
6
White
8
Black
Connector is located at immobilizer near steering column
www.idatalink.com/support
Automotive Data Solutions Inc. © 2009
XX-XX
AL(DL)
NI
CLASSIC
install guide
PAGE X-X
Transponder Bypass
Honda Prelude/Acura RL
Guides Français disponibles au www.idatalink.com
ADS-AL(TB)-PR
Page 3 of 4
Doc. No.: ##2096##
20090731
inStaLLation modE SELEction
1
PRESS AND RELEASE
programming button
to select installation mode.
2
PRESS AND HOLD
programming button
until LED turns solid GREEN
to register selection.
OR
x1
Remote Starter
Data Mode
LED flashes once
x2
!
Remote Starter
Standard Mode
LED flashes twice
After registration, follow Factory Reset Procedure to
change installation mode and restart this procedure.
moduLE Programming ProcEdurE
1
Insert key into ignition.
INSERT
2
Turn key to ON position.
3
Wait, LED will turn solid GREEN
for 2 seconds.
4
OFF
Turn key to OFF position.
ON
5
Module Programming
Procedure completed.
moduLE Programming ProcEdurE WitH PuSH to Start SyStEm
1
2

x2
DO NOT PRESS BRAKE PEDAL
Push start button twice [2x] to
ON position.
Wait, LED will turn solid GREEN
for 2 seconds.
www.idatalink.com/support
3
4

x1
DO NOT PRESS BRAKE PEDAL
Push start button once [1x] to
OFF position.
Module Programming
Procedure completed.
Automotive Data Solutions Inc. © 2009
XX-XX
CLASSIC-SERIES
install guide
PAGE X-X
1-1
Transponder Bypass
Honda Prelude/Acura RL
Guides Français disponibles au www.idatalink.com
ADS-AL(TB)-PR
Page 4 of 4
Doc. No.: ##2096##
20090731
moduLE
diagnoSticS
moduLE
diagnoSticS
dUrInG proGraMMInG
soLId red
waiting
for more vehicle
information
soLId Green
THen oFF
correctly
programmed
FLasHInG
Green
correctly
programmed
and operational
soLId red
incorrectly
programmed
Led oFF
at rest and
ready for a
r.s. sequence
soLId red
not programmed
waiting for more
vehicle
information
FLasHInG red
missing/wrong
connection or
firmware
Led oFF
no activity
or already
programmed
FLasHInG red
incorrectly
programmed
Led oFF
invalid ground
when running
status from r.s.
FLasHInG red
incorrectly
programmed
or connected
FLasHInG
Green
false ground
when running
status from r.s.
dUrInG reMoTe sTarT (r.s.)
WITH IGnITIon oFF
2
LED will turn solid red for 2
seconds.
RESET COMPLETED.
6
RECONNECT all connectors.


DISCONNECT black 4-PIN
standard or optional data
connector.
5




DISCONNECT all connectors
from module EXCEPT the black
4-PIN standard or optional data
connector.


1




Factory rESEt ProcEdurE
3
PRESS AND HOLD programming
button while connecting either
4-PIN standard or optional data
connector.
4
When LED flashes red,
RELEASE programming button.
www.idatalink.com/support
7
Repeat programming procedure.
!
Failure to follow procedure may result with a DTC or a
CHECK ENGINE error message.
Automotive Data Solutions Inc. © 2009
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising