Maytag Mdb4709aws Quick Specs
Undercounter Dishwasher
PRODUCT MODEL NUMBERS
MDB4709AW
MDB6709AW
MDB6769AW
MDBH949AW
PRODUCT DIMENSIONS
MDBH969AW
MDBH979AW
MDBTT53AW
DRAIN REQUIREMENTS
.1
( 64
• A new drain hose is supplied with your dishwasher. If this is
not long enough, use a new drain hose with a maximum
length of 12’ (3.7 m) (Part Number 3385556) that meets all
current AHAM/IAPMO test standards, is resistant to heat and
detergent, and fits the 1” (2.5 cm) drain connector of the
dishwasher.
• Make sure to connect drain hose to waste tee or disposer inlet
above drain trap in house plumbing and 20” (50.8 cm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter, or be connected to an air gap.
.2
(62
)
cm
m)
(60
.6
cm
)
c
Use of air gap
9
(1.
(86
wi cm
th )
remwh mi.n
ov eels
ed
)*
cm
Air gap
• Make sure to use an air gap if the drain hose is connected to
house plumbing lower than 20” (50.8 cm) above subfloor or
floor.
WATER SUPPLY REQUIREMENTS
"
21 cm)
• A hot water line with 20-120 psi (138-862 kPa) water pressure
can be verified by a licensed plumber.
ELECTRICAL REQUIREMENTS
You must have:
• 120-volt, 60 Hz, AC-only, 15- or 20- amp., fused electrical
supply.
• copper wire only.
We recommend:
• a time-delay fuse or circuit breaker.
• a separate circuit.
If connecting dishwasher with a power supply cord:
• Use UL Listed power supply cord kit
(Part Number 4317824) marked for
use with dishwasher.
• Power supply cord must plug into a
grounded 3 prong outlet, located in the
cabinet next to the dishwasher opening.
Outlet must meet all local codes and
ordinances.
If connecting dishwasher with direct wiring:
• Use flexible, armored or non-metallic
sheathed, copper wire with
grounding wire that meets the wiring
requirements for your home and
local codes and ordinances.
• Use a UL Listed/CSA Approved strain relief.
3.3
(5
*Insulation may
be compressed.
(not used on all models)
Page 1 of 2
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
W10290309A-D-MT
8/10
CABINET CUTOUT DIMENSIONS
Corner locations require a 2" (5.1 cm) minimum clearance between the side of the dishwasher
door and the wall or cabinet.
"
24cm)
(6124"
cm
)
(61
**
Check that all surfaces
have no protrusions that would
prohibit dishwasher installation.
.2
(10
c
3" m)
6
(7.
.2
cm
)
c
NOTE: Shaded area of cabinet walls show where utility
connections may be installed.
*Measured from the lowest point on the underside of
countertop. May be reduced to 33⁷⁄₈" (86 cm) by
removing wheels from dishwasher.
**Minimum, measured from narrowest point of
opening.
(4.
4c
(6.
(26
.7
m)
4c
m)
(15
.9
cm
)
cm
)
Cle
Arear
a
2" m )
1
(5.
c
cm
)
c
.4
(86min*
4" m)
(4
.4
(17
"
34 m)
Page 2 of 2
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
W10290309A-D-MT
8/10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising