Page 1 of 5 1999 F-150/250 Workshop Manual 6/13/2010 http://www

Page 1 of 5 1999 F-150/250 Workshop Manual 6/13/2010 http://www
1999 F-150/250 Workshop Manual
SECTION 412-04: Control Components
REMOVAL AND INSTALLATION
Page 1 of 5
1999 F-150/250 Workshop Manual
Procedure revision date: 07/09/2002
Temperature Blend Door Actuator
Removal
All vehicles
1.
WARNING: To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or
replacing any front or side air bag supplemental restraint (SRS) components and before servicing, replacing, adjusting or striking components near
the front or side air bag sensors, such as doors, instrument panel, console, door latches, strikers, seats and hood latches.
To deplete the backup power supply energy, disconnect the battery ground cable and wait at least one minute. Be sure to disconnect auxiliary
batteries and power supplies (if equipped).
Disconnect the battery ground cable and wait at least one minute. For additional information, refer to Section 414-01.
Vehicles equipped with floor console
2. Remove the floor console. For additional information, refer to Section 501-12.
All vehicles
3. Remove the floor duct panel.
Remove the pin-type retainers and release the expander clip.
4. Remove the RH instrument panel brake.
1. Remove the nut.
2. Remove the bolt.
3. Remove the brace.
5. Remove the LH instrument panel lower nut and position the brace aside.
6. Disconnect the restraints control module (RCM) electrical connector.
http://www.fordtechservice.dealerconnection.com/pubs/content/~WSX1/~MUS~LEN/19/S... 6/13/2010
1999 F-150/250 Workshop Manual
Page 2 of 5
7. Remove the RCM and bracket assembly.
1. Remove the bracket retaining bolts.
2. Remove the RCM and bracket assembly.
Vehicles equipped with rear airflow duct
8. Cut the rear seat airflow duct along both sides.
Fold back carpet.
Cut rear seat airflow duct.
9. Fold the air duct rearwards.
All vehicles
10. Remove the floor duct.
1. Remove the two screws (one each side).
2. Remove the floor duct.
http://www.fordtechservice.dealerconnection.com/pubs/content/~WSX1/~MUS~LEN/19/S... 6/13/2010
1999 F-150/250 Workshop Manual
Page 3 of 5
11. Remove the electronic blend door actuator.
1. Disconnect the connector.
2. Remove the screws.
3. Pull down to release the actuator shaft and remove the electronic blend door actuator.
Installation
All vehicles
1. Install the electronic blend door actuator.
1. Connect the actuator shaft.
2. Install the screws.
3. Connect the connector.
2. Install the floor duct.
1. Install the floor duct.
2. Install the two screws (one each side).
Vehicles equipped with rear airflow duct
3. Zip-tie the rear airflow duct to floor duct.
http://www.fordtechservice.dealerconnection.com/pubs/content/~WSX1/~MUS~LEN/19/S... 6/13/2010
1999 F-150/250 Workshop Manual
Page 4 of 5
4. Reposition the carpet.
All vehicles
WARNING: The tightening torque of the restraints control module (RCM) retaining bolts is critical for correct system operation.
5. Install the RCM and bracket assembly.
6. Connect the restraints control module (RCM) electrical connector.
7. Install the LH instrument panel lower nut.
8. Install the RH instrument panel brace.
Install the brace.
Install the nut.
Install the bolt.
http://www.fordtechservice.dealerconnection.com/pubs/content/~WSX1/~MUS~LEN/19/S... 6/13/2010
1999 F-150/250 Workshop Manual
Page 5 of 5
9. Install the floor duct panel.
Install the pin-type retainers and release the expander clip.
Vehicles equipped with floor console
10. Install the floor console. For additional information, refer to Section 501-12.
All vehicles
11. Connect the battery ground cable. For additional information, refer to Section 414-01
http://www.fordtechservice.dealerconnection.com/pubs/content/~WSX1/~MUS~LEN/19/S... 6/13/2010
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising