HP 540 Notebook PC HP 541 Notebook PC

HP 540 Notebook PC HP 541 Notebook PC
HP 540 Notebook PC
HP 541 Notebook PC
Maintenance and Service Guide
© Copyright 2008 Hewlett-Packard
Development Company, L.P.
Bluetooth is a trademark owned by its
proprietor and used by Hewlett-Packard
Company under license, and Intel, Core, and
Celeron are trademarks of Intel Corporation
in the United States and other countries.
Microsoft, Windows, and Windows Vista are
U.S. registered trademarks of Microsoft
Corporation. SD Logo is a trademark of its
proprietor.
The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
Second Edition: October 2008
First Edition: August 2008
Document Part Number: 504356–002
MSG revision history
Revision
Publication date
Description
A
January 2010
The 14.1-inch WXGA BrightView display assembly for use with the HP 541 model,
part number 517616-001, has been added in the following locations: Product
description on page 1, Computer major components on page 15, Sequential part
number listing on page 24, and Display assembly on page 53.
The LCD Cable Kit (for use only with computer models with discrete graphics system
memory), part number 517615-001, has been added in the following location:
Sequential part number listing on page 24.
iii
iv
MSG revision history
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact
the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International
Standard for Safety of Information Technology Equipment (IEC 60950).
v
vi
Safety warning notice
Table of contents
1 Product description
2 External component identification
Top components ................................................................................................................................... 7
TouchPad ............................................................................................................................ 7
Buttons, lights, and speaker ................................................................................................ 8
Keys ..................................................................................................................................... 9
Front components .............................................................................................................................. 10
Right-side components ....................................................................................................................... 10
Left-side components ......................................................................................................................... 11
Bottom components ........................................................................................................................... 12
Wireless antennae (select models only) ............................................................................................. 13
3 Illustrated parts catalog
Serial number location ........................................................................................................................ 14
Computer major components ............................................................................................................. 15
Plastics Kit .......................................................................................................................................... 19
Cable Kit ............................................................................................................................................. 20
Mass storage devices ......................................................................................................................... 21
Miscellaneous parts ............................................................................................................................ 22
Sequential part number listing ............................................................................................................ 24
4 Removal and replacement procedures
Preliminary replacement requirements ............................................................................................... 29
Tools required .................................................................................................................... 29
Service considerations ....................................................................................................... 29
Plastic parts ....................................................................................................... 29
Cables and connectors ..................................................................................... 30
Drive handling ................................................................................................... 30
Grounding guidelines ......................................................................................................... 31
Electrostatic discharge damage ........................................................................ 31
Packaging and transporting guidelines ............................................. 32
Workstation guidelines ..................................................................... 32
vii
Equipment guidelines ....................................................................... 33
Unknown user password ................................................................................................... 34
Component replacement procedures ................................................................................................. 35
Serial number .................................................................................................................... 35
Computer feet .................................................................................................................... 36
Battery ............................................................................................................................... 37
Hard drive .......................................................................................................................... 38
WLAN module .................................................................................................................... 40
Memory module ................................................................................................................. 43
Optical drive ....................................................................................................................... 45
Switch cover and keyboard ................................................................................................ 47
Speaker ............................................................................................................................. 51
Display lid switch module ................................................................................................... 52
Display assembly ............................................................................................................... 53
Top cover ........................................................................................................................... 58
TouchPad board and TouchPad button board ................................................................... 61
Bluetooth module ............................................................................................................... 64
System board ..................................................................................................................... 66
Fan ..................................................................................................................................... 69
Heat sink ............................................................................................................................ 71
Processor ........................................................................................................................... 74
Modem module .................................................................................................................. 76
RTC battery ....................................................................................................................... 78
ExpressCard assembly ...................................................................................................... 79
5 Computer Setup
Starting Computer Setup .................................................................................................................... 81
Using Computer Setup ....................................................................................................................... 82
Navigating and selecting in Computer Setup ..................................................................... 82
Restoring factory settings in Computer Setup ................................................................... 82
Computer Setup menus ..................................................................................................................... 83
File menu ........................................................................................................................... 83
Security menu .................................................................................................................... 84
Diagnostics menu .............................................................................................................. 84
System Configuration menu .............................................................................................. 85
6 Specifications
Computer specifications ..................................................................................................................... 88
14.1-inch, WXGA display specifications ............................................................................................. 89
Hard drive specifications .................................................................................................................... 90
DVD±RW and CD-RW Double-Layer Combo Drive specifications .................................................... 91
DVD/CD-RW Combo Drive specifications .......................................................................................... 92
System DMA specifications ................................................................................................................ 93
viii
System interrupt specifications ........................................................................................................... 94
System I/O address specifications ..................................................................................................... 95
System memory map specifications ................................................................................................... 97
7 Screw listing
Phillips PM2.0×5.0 captive screw ....................................................................................................... 99
Phillips PM2.5×12.0 captive screw ................................................................................................... 100
Phillips PM3.0×4.0 screw ................................................................................................................. 101
Phillips PM2.5×4.0 screw ................................................................................................................. 102
Slotted Torx ST8M2.5×7.0 screw ..................................................................................................... 103
Phillips PM2.0×4.0 screw ................................................................................................................. 106
Torx T8M2.5×3.0 broad-head screw ................................................................................................ 108
Torx T8M2.5×4.0 screw ................................................................................................................... 109
Torx T8M2.5×6.0 screw ................................................................................................................... 110
Phillips PM2.0×2.0 broad-head screw .............................................................................................. 111
Phillips PM2.0×6.0 screw ................................................................................................................. 112
Phillips PM2.5×7.0 screw ................................................................................................................. 113
Phillips PM2.5×7.0 captive screw ..................................................................................................... 114
Phillips PM2.5×10.0 captive screw ................................................................................................... 115
Phillips PM2.0×8.0 screw ................................................................................................................. 117
8 Backup and recovery
Backup and recovery in Windows Vista ........................................................................................... 118
Overview .......................................................................................................................... 118
Backing up your information ............................................................................................ 118
Performing a recovery ..................................................................................................... 119
Using the Windows recovery tools .................................................................. 120
Using f11 ......................................................................................................... 120
Using a Windows Vista operating system DVD (purchased separately) ........ 121
Backup and Recovery in Windows XP ............................................................................................. 122
Overview .......................................................................................................................... 122
Backing up your information ............................................................................................ 122
Performing a recovery ..................................................................................................... 123
Recovering your information ........................................................................... 123
Recovering the operating system and programs ............................................ 123
9 Connector pin assignments
Audio-out (headphone) ..................................................................................................................... 124
Audio-in (microphone) ...................................................................................................................... 124
External monitor ............................................................................................................................... 125
RJ-11 (modem) ................................................................................................................................ 126
RJ-45 (network) ................................................................................................................................ 127
Universal Serial Bus ......................................................................................................................... 127
ix
10 Power cord set requirements
Requirements for all countries and regions ...................................................................................... 128
Requirements for specific countries and regions ............................................................................. 129
11 Recycling
Battery .............................................................................................................................................. 130
Display .............................................................................................................................................. 130
Index ................................................................................................................................................................. 136
x
1
Product description
Category
Description
Computer models
equipped with
GLE960 system
board
Computer
models equipped
with GME965
system board
HP 540
HP 540
Computer
models
equipped with
PM965 system
board
HP 541
Product Name
HP 540 Notebook PC
√
√
HP 541 Notebook PC
Processors
√
√
Intel® Core™2 Duo processors
●
T5670 1.80-GHz processor, 2-MB L2
cache, 800-MHz front side bus (FSB)
√
√
●
T5470 1.60-GHz processor, 2-MB L2
cache, 800-MHz front side bus (FSB)
√
√
●
T5270 1.40-GHz processor, 2-MB L2
cache, 800-MHz FSB
√
√
Intel Celeron® M processors
●
P550 2.0-GHz processor, 1-MB L2
cache, 533-MHz FSB (single core)
√
●
P530 1.73-GHz processor, 533-MHz
FSB (single core)
√
√
√
√
Intel Celeron M processors, Dual Core
●
T1400 1.73-GHz processor, 533MHz
FSB
Chipset
Northbridge: Intel GME965 with up to 800MHz FSB
Northbridge: Intel GLE960 with up to 533MHz FSB
√
√
Northbridge: Intel PM965 with up to 800MHz FSB
Southbridge: Intel ICH-8M
√
√
√
√
√
1
Category
Description
Computer models
equipped with
GLE960 system
board
Computer
models equipped
with GME965
system board
HP 540
HP 540
Computer
models
equipped with
PM965 system
board
HP 541
Graphics
ATI-M62s discrete graphics subsystem
memory
√
64 MB DDR2 (16Mx16, Quantity 2)
128 MB DDR2 (16Mx16, Quantity 4)
Panel
Memory
Intel GMA X3100 Universal Memory
Architecture (UMA) graphics subsystem
integrated with shared video memory
(dynamically allocated)
√
√
All display assemblies include 2 wireless
local area network (WLAN) antennae
√
√
√
●
14.1-inch WXGA BrightView
√
√
√
●
14.1-inch WXGA BrightView
√
2 customer-accessible/upgradable
memory module slots
√
√
√
Supports dual-channel memory
√
√
√
Supports up to 4 GB of system RAM
√
√
√
PC2-5300, 667-MHz, DDR2
√
√
√
√
√
√
√
Supports the following configurations in all
countries and regions except Brazil:
2
●
4096-MB total system memory (2048
× 2, dual-channel)
●
3072-MB total system memory (2048
+ 1024)
●
2560-MB total system memory (2048
+ 512)
●
2048-MB total system memory (1024
× 2, dual-channel)
●
2048-MB total system memory (2048
× 1)
●
1536-MB total system memory (1024
+ 512)
●
1024-MB total system memory (512 ×
2, dual-channel)
●
1024-MB total system memory (1024
× 1)
●
512-MB total system memory (512 ×
1)
Chapter 1 Product description
√
Category
Description
Computer models
equipped with
GLE960 system
board
Computer
models equipped
with GME965
system board
HP 540
HP 540
Computer
models
equipped with
PM965 system
board
HP 541
Supports the following configurations only
in Brazil:
Hard drives
Optical drives
Diskette drive
√
√
Supports 9.5-mm, 2.5-inch hard drives
√
√
√
Customer-accessible
√
√
√
Serial ATA
√
√
√
Supports the following drives:
√
√
√
HP 3D DriveGuard
√
√
√
Fixed (removal of 1 screw required)
√
√
√
Customer-accessible
√
√
√
Parallel ATA
√
√
Serial ATA
√
√
√
12.7-mm tray load
√
√
√
Supports the following drives:
√
√
√
Supports external USB diskette drive only
√
√
√
Supports boot from external USB diskette
drive
√
√
√
Supports 3-mode diskette drive
√
√
√
●
2048-MB total system memory (2048
× 1)
●
2048-MB total system memory (1024
× 2, dual-channel)
●
1024-MB total system memory (1024
× 1)
●
1024-MB total system memory (512 ×
2, dual-channel)
●
512-MB total system memory (512 ×
1)
●
250-GB, 5400-rpm
●
160-GB, 5400-rpm
●
120-GB, 5400-rpm
●
DVD±RW and CD-RW Super Multi
Double-Layer Combo Drive with
LightScribe
●
DVD/CD-RW Combo Drive
●
DVD-ROM Drive
3
Category
Description
Computer models
equipped with
GLE960 system
board
Computer
models equipped
with GME965
system board
HP 540
HP 540
Computer
models
equipped with
PM965 system
board
HP 541
Audio
HD audio - ADI1981
√
√
√
Modem
56K Vulcan-F 1.5-inch data/fax modem
with digital line guard
√
√
√
Ethernet
Intel 82562GT
√
√
√
S3/S4/S5 wake on LAN: DC - no
√
√
√
S3/S4/S5 wake on LAN: AC - yes
√
√
√
Wireless
Integrated WLAN options by way of wireless module:
2 WLAN antennae built into display
assembly
√
√
√
Support for no-WLAN option
√
√
√
Support for the following WLAN formats:
√
√
√
●
Intel 802.11 a/b/g/n
●
Broadcom 802.11 a/b/g
●
Broadcom 802.11 b/g
●
Intel 802.11 a/b/g
●
Intel 802.11 b/g
●
Intel Kedron 802.11 a/b/g without
iAMT
●
Intel Kedron 802.11 a/b/g/n without
iAMT
Integrated personal area network (PAN) options by way of Bluetooth® module:
External media
card
Ports
4
Support for no-WPAN option
√
√
√
Broadcom Bluetooth 2.0+EDR
√
√
√
One ExpressCard/54 slot
√
√
√
SD Card Reader supporting Secure Digital
(SD) Memory Card and MultiMediaCard
(MMC)
√
√
√
Audio-in (stereo microphone)
√
√
√
Audio-out (stereo headphone)
√
√
√
RJ-11 (modem)
√
√
√
RJ-45 (Ethernet, includes link and activity
lights)
√
√
√
USB (3)
√
√
√
Chapter 1 Product description
Category
Description
Computer models
equipped with
GLE960 system
board
Computer
models equipped
with GME965
system board
HP 540
HP 540
Computer
models
equipped with
PM965 system
board
HP 541
Keyboard/
pointing
devices
Power
requirements
VGA (Dsub 15-pin) supporting 1600 ×
1200 external resolution at 75-GHz (hot
plug/unplug with auto-detect)
√
√
√
2-pin AC power
√
√
√
11.97-inch keyboard with embedded
numeric keypad
√
√
√
TouchPad only, with 2 TouchPad buttons
and vertical scrolling (taps enabled as
default)
√
√
√
90-W AC adapter with localized cable plug
support (2-wire plug with ground pin,
supports 2-pin DC connector)
√
65-W AC adapter with localized cable plug
support (2-wire plug with ground pin,
supports 2-pin DC connector)
√
√
6-cell, 47-Wh Li-ion battery
√
√
√
Security
Supports Kensington security lock
√
√
√
Operating
system
Preinstalled:
Windows Vista® Basic 32 with Office
Ready
√
√
√
Windows Vista Basic 32 Japan with Office
Personal (in Japan only)
√
√
Windows Vista Basic 32 Japan with Office
Personal with PowerPoint (in Japan only)
√
√
Windows Vista Basic 32 Japan with Office
Professional (in Japan only)
√
√
Windows Vista Business 32
√
√
Windows Vista Business 32 with Office
Ready (in Japan only)
√
√
Windows Vista Business 32 Japan with
Office Personal (in Japan only)
√
√
Windows Vista Business 32 Japan with
Office Personal with PowerPoint (in Japan
only)
√
√
√
√
√
Windows Vista Business 32 Japan with
Office Professional (in Japan only)
Windows Vista Business with Windows®
XP Professional with Office Ready
√
5
Category
Description
Computer models
equipped with
GLE960 system
board
Computer
models equipped
with GME965
system board
HP 540
HP 540
Computer
models
equipped with
PM965 system
board
HP 541
Windows Vista Business with XP
Professional (in Japan only)
√
√
Windows Vista Business with XP
Professional with Office Personal (in Japan
only)
√
√
Windows Vista Business with XP
Professional with Office Personal with
PowerPoint (in Japan only)
√
√
Windows Vista Business with XP
Professional with Office Professional (in
Japan only)
√
√
FreeDOS
√
√
√
Red Flag Linux (in the People's Republic of
China only)
√
√
√
Mandriva Linux
√
√
Windows Vista Basic 32
√
√
√
Windows Vista Business 32
√
√
√
Office Ready DVD
√
√
√
Windows XP Professional
√
√
√
Red Flag Linux (in the People's Republic of
China only)
√
√
√
DRDVD Windows Vista
√
√
√
DRDVD Windows XP Pro
√
√
√
Web Support: Windows XP Professional
√
√
√
Certified: Microsoft® WHQL
√
√
√
AC adapter
√
√
√
Battery (system)
√
√
√
Hard drive
√
√
√
Memory module
√
√
√
Optical drive
√
√
√
WLAN module
√
√
√
Restore media:
Serviceability
6
End-user replaceable parts:
Chapter 1 Product description
2
External component identification
Top components
TouchPad
Item
Component
Function
(1)
TouchPad*
Moves the pointer and selects or activates items on the
screen.
(2)
Left TouchPad button*
Functions like the left button on an external mouse.
(3)
Right TouchPad button*
Functions like the right button on an external mouse.
(4)
TouchPad scroll zone
Scrolls up or down.
*This table describes factory settings. View or change pointing device preferences as follows:
●
In Windows Vista, select Start > Control Panel > Hardware and Sound > Mouse.
●
In Windows XP, select Start > Control Panel > Printers and Other Hardware > Mouse.
Top components
7
Buttons, lights, and speaker
Item
Component
Function
(1)
Caps lock light
On: Caps lock is on.
(2)
Wireless button
Turns the wireless feature on or off, but does not establish
a wireless connection.
NOTE: You must set up or access a wireless network to
establish a wireless connection.
(3)
(4)
Wireless light
Power button
●
Blue: An integrated wireless device, such as a
wireless local area network (WLAN) device, the HP
Broadband Wireless Module, and/or a Bluetooth®
device, is on.
●
Amber: All wireless devices are off.
●
When the computer is off, press the button to turn on
the computer.
●
When the computer is on, press the button to initiate
Hibernation.
●
When the computer is in the Sleep state (Windows
Vista) or in Standby (Windows XP), press the button
briefly to exit the Sleep state or Standby.
●
When the computer is in Hibernation, press the button
briefly to exit Hibernation.
If the computer has stopped responding and Windows®
shutdown procedures are ineffective, press and hold the
power button for at least 5 seconds to turn off the computer.
To learn more about power settings, follow these steps:
8
Chapter 2 External component identification
●
In Windows Vista, select Start > Control Panel >
System and Maintenance > Power Options.
●
In Windows XP, select Start > Control Panel >
Performance and Maintenance > Power Options.
Item
Component
Function
(5)
Power light
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state (Windows
Vista) or Standby (Windows XP).
●
Off: The computer is off or in Hibernation.
(6)
Speaker
Produces sound.
Item
Component
Function
(1)
esc key
Displays system information when pressed in combination
with the fn key.
(2)
fn key
Executes frequently used system functions when pressed
in combination with a function key or the esc key.
(3)
Windows logo key
Displays the Windows Start menu.
(4)
Windows applications key
Displays a shortcut menu for items beneath the pointer.
(5)
Embedded numeric keypad keys
Can be used like the keys on an external numeric keypad.
(6)
Function keys
Execute frequently used system functions when pressed
in combination with the fn key.
Keys
Top components
9
Front components
Item
Component
Function
(1)
Audio-out (headphone) jack
Connects optional powered stereo speakers, headphones,
ear buds, a headset, or television audio.
(2)
Audio-in (microphone) jack
Connects an optional computer headset microphone,
stereo array microphone, or monaural microphone.
(3)
SD Card Reader
Supports the following optional digital card formats:
●
Secure Digital (SD) Memory Card
●
MultiMediaCard (MMC)
Right-side components
Item
Component
Function
(1)
Optical drive
Reads an optical disc.
(2)
Security cable slot
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a
deterrent, but it may not prevent the computer from being
mishandled or stolen.
10
Chapter 2 External component identification
Left-side components
Item
Component
Function
(1)
RJ-11 (modem) jack
Connects a modem cable.
(2)
Vent
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(3)
External monitor port
Connects an external VGA monitor or projector.
(4)
Power connector
Connects an AC adapter.
(5)
RJ-45 (network) jack
Connects a network cable.
(6)
USB ports (3)
Connect optional USB devices.
(7)
ExpressCard slot
Supports optional ExpressCards.
(8)
Battery light
●
Amber: A battery is charging.
●
Turquoise: A battery is close to full charge capacity.
●
Blinking amber: A battery that is the only available
power source has reached a low battery level. When
the battery reaches a critical battery level, the battery
light begins blinking rapidly.
●
Off: If the computer is plugged into an external power
source, the light turns off when all batteries in the
computer are fully charged. If the computer is not
plugged into an external power source, the light stays
off until the battery reaches a low battery level.
Left-side components
11
Bottom components
Item
Component
Function
(1)
Battery release latches (2)
Release the battery from the battery bay.
(2)
Battery bay
Holds the battery.
(3)
Vents (6)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(4)
Memory module compartment
Contains the memory module slots.
(5)
WLAN module compartment (select models only)
Contains a WLAN module slot.
NOTE: To prevent an unresponsive system, replace the
wireless module only with a wireless module authorized for
use in the computer by the governmental agency that
regulates wireless devices in your country or region. If you
replace the module and then receive a warning message,
remove the module to restore computer functionality, and
then contact technical support through Help and Support.
(6)
12
Hard drive bay
Chapter 2 External component identification
Holds the hard drive.
Wireless antennae (select models only)
On select computer models, at least 2 antennae send and receive signals from one or more wireless
devices. These antennae are not visible from the outside of the computer.
NOTE: For optimal transmission, keep the areas immediately around the antennae free from
obstructions.
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental
Notices that applies to your country or region. These notices are located in Help and Support.
Wireless antennae (select models only)
13
3
Illustrated parts catalog
Serial number location
When ordering parts or requesting information, provide the computer serial number and model number
located on the bottom of the computer.
14
●
Product Name (1). This is the product name affixed to the front of the computer.
●
Serial Number (s/n) (2). This is an alphanumeric identifier that is unique to each product.
●
Part Number/Product Number (p/n) (3). This number provides specific information about the
product's hardware components. The part number helps a service technician to determine what
components and parts are needed.
●
Model Description (4). This is the number you use to locate documents, drivers, and support for
your notebook.
●
Warranty Period (5). This number describes the duration (in years) of the warranty period for this
computer.
Chapter 3 Illustrated parts catalog
Computer major components
Computer major components
15
Item
Description
(1)
Display assemblies (include 2 WLAN antenna transceivers and cables)
Spare part number
14.1-inch, WXGA BrightView display assembly for use with HP 540 models
500004-001
14.1-inch, WXGA BrightView display assembly for use with HP 541 models
517616-001
Display internal components:
Display bezel
500000-001
Display enclosure (includes 2 WLAN antenna transceivers and cables)
500001-001
Display hinges (includes left and right hinges)
456619-001
Display inverter
456618-001
(2)
Switch cover (includes LED board and cable)
500001-001
(3)
Keyboards
For use in Brazil
499999-201
For use in Japan
499999-291
For use in Latin America
499999-161
For use in South Korea
499999-AD1
For use in Taiwan
499999-281
For use in Thailand
499999-AB1
For use in the United States
499999-001
(4)
Speaker
456593-001
(5)
Top cover (includes TouchPad board and cable, and TouchPad button board and cable)
500002-001
Plastics Kit (see Plastics Kit on page 19 for more Plastics Kit spare part information):
456614-001
(6a)
ExpressCard slot protective insert
(6b)
WLAN module compartment cover
(6c)
Memory module compartment cover
(6d)
Hard drive bay cover
TouchPad components (included with the top cover)
(7a)
TouchPad bracket
(7b)
TouchPad board (includes cable)
(7c)
TouchPad button board (includes cable)
(8)
Fan
(9)
System boards (include replacement thermal material and the ExpressCard assembly)
(10)
16
431312-001
●
For use only with computer models equipped with Intel Core2 Duo processors and UMA
graphics subsystem
495410-001
●
For use only with computer models equipped with Intel Celeron M processors and UMA
graphics subsystem
495395-001
Heat sinks (include replacement thermal material)
Chapter 3 Illustrated parts catalog
Item
(11)
Description
Spare part number
For use only with computer models equipped with UMA graphics subsystem
456605-001
For use only with computer models equipped with discrete graphics subsystem
456606-001
Processors (includes replacement thermal material)
Intel Core2 Duo processors:
●
T5670 1.8-GHz (2-MB L2 cache, 800-MHz FSB)
508756-001
●
T5470 1.60-GHz (2-MB L2 cache, 800-MHz FSB)
500007-001
●
T5270 1.40-GHz (2-MB L2 cache, 800-MHz FSB)
500005-001
Intel Celeron M processors:
●
P550 2.0-GHz (1-MB L2 cache, 533-MHz FSB)
508757-001
●
P530 1.73-GHz (1-MB L2 cache, 533-MHz FSB)
500006-001
Intel Celeron M Dual Core processors:
●
506448-001
T1400 1.73-GHz (1-MB L2 cache, 533-MHz FSB)
(12)
RTC battery
(13)
Broadcom Bluetooth modules (do not include Bluetooth module cable)
449137-001
NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth module cable
is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 20 for more Cable Kit spare part
number information.
(14)
For use in all countries and regions except Japan and Asia Pacific countries and regions
398393-002
For use only in Japan and Asia Pacific countries and regions
450066-001
Modem modules
NOTE: The modem module spare part kits do not include a modem module cable. The modem module cable is
included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 20 for more Cable Kit spare part
number information.
(15)
For use only in the United States
461749-001
For use only in Japan and Asia Pacific countries and regions
461749–011
Base enclosure (includes rubber feet)
For use only with computer models equipped with UMA graphics subsystem (includes rubber
feet)
500003-001
For use only with computer models equipped with discrete graphics subsystem (includes
rubber feet)
460702-001
Rubber Kit (not illustrated, contains 4 computer feet and 8 display bezel screw covers)
500132-001
(16)
6-cell, 47-Wh Li-ion battery
500014-001
(17)
Optical drives (include bezel and bracket)
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe
500018-001
DVD/CD-RW Combo Drive
500017-001
DVD-ROM Drive
500016-001
Computer major components
17
Item
(18)
Description
Spare part number
Cable Kit (not illustrated; see Cable Kit on page 20 for more Cable Kit spare part number
information)
457400-001
WLAN modules
Intel 802.11 a/b/g/n WLAN modules:
●
For use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India,
Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay,
the United States, Venezuela, and Vietnam
441086-001
●
For use in Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania,
Luxembourg, Malta, Monaco, the Netherlands, Norway, Oman, the Philippines, Poland,
Portugal, Qatar, Romania, Russia, Serbia and Montenegro, Singapore, Slovakia,
Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the
United Kingdom, and Uzbekistan
441086-002
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South
Korea
441086-003
Intel 802.11 a/b/g WLAN modules:
(19)
(20)
18
●
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India,
Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United
States, Uruguay, Venezuela, and Vietnam
451861-001
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the
Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania,
Luxembourg, Malta, Monaco, the Netherlands, Norway, Oman, the Philippines, Poland,
Portugal, Qatar, Romania, Russia, Serbia and Montenegro, Singapore, Slovakia,
Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the
United Kingdom, and Uzbekistan
451861-002
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South
Korea
451861-003
●
For use in Japan
451861–291
●
For use in South Korea
456576-AD1
Memory modules (PC2-5300, 667-MHz, DDR2)
2-GB
500009-001
1-GB
500008-001
512-MB
500010-001
Hard drives (include hard drive bracket)
250-GB, 5400-rpm
500013-001
160-GB, 5400-rpm
500012-001
120-GB, 5400-rpm
500011-001
Chapter 3 Illustrated parts catalog
Plastics Kit
Item
Description
Spare part number
Plastics Kit:
456614-001
(1)
Hard drive bay cover (includes 2 captive screws, secured by C-clips)
(2)
WLAN module compartment cover (includes one captive screw, secured by a C-clip)
(3)
ExpressCard slot protective insert
(4)
Memory module compartment cover (includes one captive screw, secured by a C-clip)
Plastics Kit
19
Cable Kit
Item
20
Description
Spare part number
Cable Kit:
457400-001
(1)
RJ-11 jack cable
(2)
Display lid switch module and cable
(3)
Bluetooth module cable
Chapter 3 Illustrated parts catalog
Mass storage devices
Item
Description
(1)
Optical drives (include bezel and bracket)
(2)
Spare part number
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe (PATA)
500018-001
DVD CD-RW Combo Drive (PATA)
500017-001
DVD-ROM Drive (PATA)
500016-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe (SATA)
506010-011
DVD CD-RW Combo Drive (SATA)
506011-011
DVD-ROM Drive (SATA)
495387-001
Hard drives (include bracket)
250-GB, 5400-rpm
500013-001
160-GB, 5400-rpm
500012-001
120-GB, 5400-rpm
500011-001
Mass storage devices
21
Miscellaneous parts
Description
Spare part number
AC adapters
65-W AC adapter (for use only with computer models with UMA graphics system memory)
417220-001
90-W slim AC adapter (for use only with computer models with discrete graphics system memory)
for use in Asia and China.
374791-001
Logo Kit
495408-001
Nylon carrying case
325814-001
USB 1.1 diskette drive
359118-001
Power cords:
22
For use in Australia
490371–011
For use in the United States
490371-001
For use in the United Kingdom and Singapore
490371-011
For use in Brazil
490371-201
For use in Japan
490371-291
For use in the People's Republic of China
490371-AA1
For use in Taiwan
490371-AB1
Chapter 3 Illustrated parts catalog
Description
Spare part number
For use in Korea
490371-AD1
Screw Kit
500130-001
●
Phillips PM3.0×4.0 screw
●
Phillips PM2.5×12.0 captive screw
●
Phillips PM2.5×10.0 captive screw
●
Phillips PM2.5×7.0 captive screw
●
Phillips PM2.5×7.0 screw
●
Phillips PM2.5×4.0 screw
●
Phillips PM2.0×8.0 screw
●
Phillips PM2.0×6.0 screw
●
Phillips PM2.0×5.0 captive screw
●
Phillips PM2.0×4.0 screw
●
Phillips PM2.0×2.0 broad-head screw
●
Torx T8M2.5×9.0 screw
●
Slotted Torx ST8M2.5×7.0 screw
●
Torx T8M2.5×6.0 screw
●
Torx T8M2.5×4.0 screw
●
Torx T8M2.5×3.0 broad-head screw
●
Torx T8M2.0×4.0 screw
Miscellaneous parts
23
Sequential part number listing
Spare part
number
Description
374791-001
90-W slimline AC adapter (for use only with computer models with discrete graphics system memory) for use
in Asia and China.
398393-002
Bluetooth module for use in North America
NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth module
cable is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 20 for more Cable
Kit spare part number information.
417220-001
65-W AC adapter (for use only with computer models with UMA graphics system memory)
431312-001
Fan
441082-001
Intel 802.11 a/b/g WLAN module for use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados,
Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic,
Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico,
Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay, Venezuela, and Vietnam
441082-002
Intel 802.11 a/b/g WLAN module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, the
Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania, Russia, Serbia and
Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey,
Ukraine, the United Kingdom, and Uzbekistan
441082-003
Intel 802.11 a/b/g WLAN module for use in Australia, New Zealand, Pakistan, the People's Republic of China,
and South Korea
441082-292
Intel 802.11 a/b/g WLAN module for use in Japan
441086-001
Intel 802.11 a/b/g/n WLAN module for use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados,
Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic,
Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico,
Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay, Venezuela, and Vietnam
441086-002
Intel 802.11 a/b/g/n WLAN module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, the
Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania, Russia, Serbia and
Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey,
Ukraine, the United Kingdom, and Uzbekistan
441086-003
Intel 802.11 a/b/g/n WLAN module for use in Australia, New Zealand, Pakistan, the People's Republic of China,
and South Korea
441086-291
Intel 802.11 a/b/g/n WLAN module for use in Japan
449137-001
RTC battery
450066-001
Bluetooth module for use in Japan and Asia Pacific countries and regions
NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth module
cable is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 20 for more Cable
Kit spare part number information.
451861-001
24
Intel 802.11 a/b/g WLAN module for use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados,
Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic,
Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico,
Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay, Venezuela, and Vietnam
Chapter 3 Illustrated parts catalog
Spare part
number
Description
451861-002
Intel 802.11 a/b/g WLAN module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, the
Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania, Russia, Serbia and
Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey,
Ukraine, the United Kingdom, and Uzbekistan
451861-003
Intel 802.11 a/b/g WLAN module for use in Australia, New Zealand, Pakistan, the People's Republic of China,
and South Korea
451861-291
Intel 802.11 a/b/g WLAN module for use in Japan
456576-AD1
Intel 802.11 a/b/g/n WLAN module for use in South Korea
456593-001
Speaker
456605-001
Heat sink for use only with computer models equipped with UMA graphics subsystem (includes replacement
thermal material)
456606-001
Heat sink for use only with computer models equipped with discrete graphics subsystem (includes replacement
thermal material)
456614-001
Plastics Kit (see Plastics Kit on page 19 for more Plastics Kit spare part information)
456618-001
Display inverter
456619-001
Display hinges (includes left and right hinges)
457400-001
Cable Kit (see Cable Kit on page 20 for more Cable Kit spare part information)
459263-001
Broadcom 802.11b/g WLAN module
459263-002
Broadcom 802.11b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and
Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central
African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor,
Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French
Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala,
Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali,
Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia,
Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New
Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay,
Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San
Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka,
St. Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan,
Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda,
Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zaire, Zambia, and Zimbabwe
460702-001
Base enclosure for use only with computer models equipped with discrete graphics subsystem (includes
rubber feet)
461749-001
Modem module for use in the United States (includes modem module cable)
NOTE: The modem module spare part kits do not include a modem module cable. The modem module cable
is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 20 for more Cable Kit
spare part number information.
Sequential part number listing
25
Spare part
number
Description
461749-011
Modem module or use only in Japan and Asia Pacific countries and regions (includes modem module
cable)
NOTE: The modem module spare part kits do not include a modem module cable. The modem module cable
is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 20 for more Cable Kit
spare part number information.
487330-001
802.11 a/b/g/n WLAN module
487330-002
802.11 a/b/g/n WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the
British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African
Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia,
Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador,
Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon,
Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, GuineaBissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia,
Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta,
the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,
Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand,
Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru,
the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka,
St. Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan,
Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda,
Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zaire, Zambia, and Zimbabwe
490371-001
Power cord for use in the United States
490371-011
Power cord for use in Australia and New Zealand
490371-031
Power cord for use in the United Kingdom and Singapore
490371-201
Power cord for use in Brazil
490371-291
Power cord for use in Japan
490371-AA1
Power cord for use in the People's Republic of China
490371-AB1
Power cord for use in Taiwan
490371-AD1
Power cord for use in Korea
490371-D01
Power cord for use in Argentina
490371-D611
Power cord for use in India
495386-001
26
495387-001
DVD-ROM Drive (SATA)
495395-001
System board for use only with computer models equipped with Intel Celeron M processors and UMA graphics
subsystem (includes replacement thermal material and the ExpressCard assembly)
495408-001
Logo Kit
495410-001
System board for use only with computer models equipped with Intel Core2 Duo processors and UMA graphics
subsystem (includes replacement thermal material and the ExpressCard assembly)
499999-001
Keyboard for use in the United States
Chapter 3 Illustrated parts catalog
Spare part
number
Description
499999-161
Keyboard for use in Latin America
499999-201
Keyboard for use in Brazil
499999-281
Keyboard for use in Thailand
499999-291
Keyboard for use in Japan
499999-AB1
Keyboard for use in Taiwan
499999-AD1
Keyboard for use in South Korea
500000-001
Display enclosure (includes 2 wireless antenna transceivers and cables)
500001-001
Switch cover (includes LED board and cable)
500002-001
Top cover (includes TouchPad board and cable, and TouchPad button board and cable)
500003-001
Base enclosure for use with UMA graphics subsystem (includes rubber feet)
500004-001
14.1-inch, WXGA display assembly for use with HP 540 models (includes 2 WLAN antenna transceivers and
cables)
500005-001
Intel Core2 Duo T5270 1.40-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
500006-001
Intel Celeron M P530 1.73-GHz processor (1-MB L2 cache, 533-MHz FSB, includes replacement thermal
material)
500007-001
Intel Core2 Duo T5470 1.60-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
500008-001
1-GB memory module (PC2-5300, 667-MHz, DDR2)
500009-001
2-GB memory module (PC2-5300, 667-MHz, DDR2)
500010-001
512-MB memory module (PC2-5300, 667-MHz, DDR2)
500011-001
120-GB, 5400-rpm hard drive (includes bracket)
500012-001
160-GB, 5400-rpm hard drive (includes bracket)
500013-001
250-GB, 5400-rpm hard drive (includes bracket)
500014-001
6-cell, 47-Wh Li-ion battery
500016-001
DVD-ROM Drive (includes bezel and bracket) (PATA)
500017-001
DVD/CD-RW Combo Drive (includes bezel and bracket) (PATA)
500018-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe (includes bezel and bracket)
(PATA)
500130-001
Screw Kit
500132-001
Rubber Kit (contains 4 computer feet and 8 display bezel screw covers)
506010-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe (includes bezel and bracket)
(SATA)
506011-001
DVD/CD-RW Combo Drive (includes bezel and bracket) (SATA)
506448-001
Intel Celeron M T1400 1.73-GHz (1-MB L2 cache, 533-MHz FSB)
508756-001
Intel Core2 Duo T5670 2.0-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
Sequential part number listing
27
28
Spare part
number
Description
508757-001
Intel Celeron M P550 2.0-GHz (1-MB L2 cache, 533-MHz FSB)
508815-001
LCD Cable Kit (for use only with computer models with UMA graphics system memory)
509115-001
System board for use with computer models with discrete memory subsystem
509116-001
System board for use with computer models with discrete memory subsystem
511030-001
Logo kit for computer models with discrete memory subsystem
517615-001
LCD Cable Kit (for use only with computer models with discrete graphics system memory)
517616-001
14.1-inch, WXGA display assembly for use with HP 541 models (includes 2 WLAN antenna transceivers and
cables)
Chapter 3 Illustrated parts catalog
4
Removal and replacement procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●
Flat-bladed screwdriver
●
Magnetic screwdriver
●
Phillips P0 and P1 screwdrivers
●
Torx T8 screwdriver
Service considerations
The following sections include some of the considerations that you must keep in mind during
disassembly and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
Using excessive force during disassembly and reassembly can damage plastic parts. Use care when
handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.
Preliminary replacement requirements
29
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat
or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In
all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that
they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme
care; these cables tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the
computer is off or in Hibernation, turn the computer on, and then shut it down through the operating
system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and
be sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
30
Chapter 4 Removal and replacement procedures
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some protection,
but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a
normal cycle. Or the device may function normally for a while, then degrade in the internal layers,
reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you are ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines described
in this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by different
activities.
CAUTION:
A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
Preliminary replacement requirements
31
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
●
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●
Place items on a grounded surface before removing items from their containers.
●
Always be properly grounded when touching a component or assembly.
●
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive
foam.
●
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that
mechanized equipment used for moving materials is wired to ground and that proper materials are
selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate
electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
32
●
Cover the workstation with approved static-shielding material.
●
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools
and equipment.
●
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
●
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
●
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
●
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle
these items only at static-free workstations.
●
Avoid contact with pins, leads, or circuitry.
●
Turn off power and input signals before inserting or removing connectors or test equipment.
Chapter 4 Removal and replacement procedures
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground,
wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors,
use alligator clips to connect a wrist strap.
●
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps)
can be used at standing workstations and are compatible with most types of shoes or boots. On
conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one
megohm resistance between the operator and ground. To be effective, the conductive strips must
be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●
Antistatic tape
●
Antistatic smocks, aprons, and sleeve protectors
●
Conductive bins and other assembly or soldering aids
●
Nonconductive foam
●
Conductive tabletop workstations with ground cords of one megohm resistance
●
Static-dissipative tables or floor mats with hard ties to the ground
●
Field service kits
●
Static awareness labels
●
Material-handling packages
●
Nonconductive plastic bags, tubes, or boxes
●
Metal tote boxes
●
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material
Use
Voltage protection level
Antistatic plastic
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
Preliminary replacement requirements
33
Unknown user password
If the computer you are servicing has an unknown user password, follow these steps to clear the
password:
NOTE:
These steps also clear CMOS.
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the real-time clock (RTC) battery (see RTC battery on page 78).
6.
Wait approximately 5 minutes.
7.
Replace the RTC battery and reassemble the computer.
8.
Connect AC power to the computer. Do not reinsert any batteries at this time.
9.
Turn on the computer.
All passwords and all CMOS settings have been cleared.
34
Chapter 4 Removal and replacement procedures
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 76 screws, in 16 different sizes, that must be removed, replaced, or loosened
when servicing the computer. Make special note of each screw size and location during removal and
replacement.
Serial number
Report the computer serial number to HP when requesting information or ordering spare parts. The
serial number is located on the bottom of the computer.
●
Product Name (1). This is the product name affixed to the front of the computer.
●
Serial Number (s/n) (2). This is an alphanumeric identifier that is unique to each product.
●
Part Number/Product Number (p/n) (3). This number provides specific information about the
product's hardware components. The part number helps a service technician to determine what
components and parts are needed.
●
Model Description (4). This is the number you use to locate documents, drivers, and support for
your notebook.
●
Warranty Period (5). This number describes the duration (in years) of the warranty period for this
computer.
Component replacement procedures
35
Computer feet
The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare
part number 500132-001. There are 4 rubber feet that attach to the base enclosure in the locations
illustrated below.
36
Chapter 4 Removal and replacement procedures
Battery
Description
Spare part number
6-cell, 47-Wh Li-ion battery
456623-001
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the battery:
1.
Turn the computer upside down on a flat surface, with the battery bay toward you.
2.
Slide the battery release latches (1) to release the battery.
3.
Remove the battery (2) from the computer.
Insert the battery into the battery bay until it is seated. The battery release latches automatically lock
the battery into place.
Component replacement procedures
37
Hard drive
NOTE:
All hard drive spare part kits include a hard drive bracket.
Description
Spare part number
250-GB, 5400-rpm hard drive
500012-001
160-GB, 5400-rpm hard drive
500011-001
120-GB, 5400-rpm hard drive
500010-001
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
Remove the hard drive:
38
1.
Position the computer with the front toward you.
2.
Loosen the two Phillips PM2.0×5.0 captive screws (1) that secure the hard drive bay cover to the
computer.
3.
Lift the right side of the hard drive bay cover (2), swing it to left, and remove the cover. The hard
drive bay cover is included in the Plastics Kit, spare part number 456614-001.
4.
Loosen the Phillips PM2.5×12.0 captive screw (1) that secures the hard drive to the computer.
5.
Grasp the Mylar tab (2) on the hard drive and slide the hard drive (3) to the left to disconnect it from
the system board.
Chapter 4 Removal and replacement procedures
6.
Remove the hard drive (4) from the hard drive bay.
7.
If it is necessary to replace the hard drive bracket, remove the two Phillips PM3.0×4.0 hard drive
bracket screws (1) from each side of the hard drive.
8.
Lift the bracket (2) straight up to remove it from the hard drive.
Reverse this procedure to reassemble and install the hard drive.
Component replacement procedures
39
WLAN module
Description
spare part numbers
Intel 802.11 a/b/g/n WLAN modules:
●
For use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei,
Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador,
El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia,
Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United States,
Venezuela, and Vietnam.
441086-001
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania,
Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka,
Sweden, Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan.
441086-002
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South Korea.
441086-003
●
For use in Japan.
441086-291
●
For use in South Korea:
456576-AD1
Broadcom 802.11 a/b/g/n/ WLAN module
●
For use in the United States.
487330-001
●
802.11 a/b/g/n WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua
and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas,
Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina
Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's
Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech
Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt,
El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,
Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe,
Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland,
India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati,
Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg,
Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,
Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,
Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New
Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New
Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania,
Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia
and Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St.
Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania,
Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine,
the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela,
Vietnam, Yemen, Zaire, Zambia, and Zimbabwe.
487330-002
Intel 802.11 a/b/g WLAN module
●
40
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei,
Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador,
El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia,
Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay,
Venezuela, and Vietnam.
Chapter 4 Removal and replacement procedures
441082-001
Description
spare part numbers
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania,
Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka,
Sweden, Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan.
441082-002
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South Korea.
441082-003
●
For use in Japan.
441082-292
Intel 802.11 b/g WLAN modules:
●
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei,
Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador,
El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia,
Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay,
Venezuela, and Vietnam
451861-001
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania,
Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka,
Sweden, Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan
451861-002
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South Korea
451861-003
●
For use in Japan
451861-291
Broadcom 802.11 b/g WLAN modules:
●
For use in the United States.
●
459263-002
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua & Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia & Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia,
Cameroon, Cape Verde, the Central African Republic, Chad, Chile, Colombia, Comoros, the
Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the
Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea,
Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany,
Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana,
Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory
Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia,
Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar,
Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania,
Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger,
Nigeria, Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, the People's Republic
of China, Peru, the Philippines, Poland, Portugal, Qatar, the Republic of Moldova, Romania,
Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia
and Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St.
Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania,
Thailand, Togo, Tonga, Trinidad & Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda,
Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu,
Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe.
459263-001
Component replacement procedures
41
Before removing the WLAN module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
Remove the WLAN module:
1.
Position the computer with the front toward you.
2.
Loosen the Phillips PM2.0×5.0 captive screw (1) that secures the WLAN module compartment
cover to the computer.
3.
Lift the right side of the WLAN module compartment cover (2), swing it to left, and remove the
cover. The WLAN module compartment cover is included in the Plastics Kit, spare part number
456614-001.
4.
Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.
NOTE: The black WLAN antenna cable is connected to the WLAN module “Main” terminal. The
white WLAN antenna cable is connected to the WLAN module “Aux” terminal.
5.
42
Remove the two Phillips PM2.5×4.0 screws (2) that secure the WLAN module to the computer.
(The edge of the module opposite the slot rises away from the computer.)
Chapter 4 Removal and replacement procedures
6.
Remove the WLAN module (3) by pulling the module away from the slot at an angle.
NOTE:
WLAN modules are designed with a notch (4) to prevent incorrect insertion.
Reverse this procedure to install the WLAN module.
Memory module
Description
spare part numbers
2-GB (PC2-5300, 667-MHz, DDR2)
500009-001
1-GB (PC2-5300, 667-MHz, DDR2)
500008-001
512-MB (PC2-5300, 667-MHz, DDR2)
500010-001
Before removing the memory module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
Remove the memory module:
1.
Loosen the Phillips PM2.0×5.0 captive screw (1) that secures the memory module compartment
cover to the computer.
Component replacement procedures
43
2.
Lift the front edge of the cover (2), swing it up and back, and remove the cover. The memory module
compartment cover is included in the Plastics Kit, spare part number 456614-001.
3.
Spread the retaining tabs (1) on each side of the memory module slot to release the memory
module. (The edge of the module opposite the slot rises away from the computer.)
4.
Remove the memory module (2) by pulling the module away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the
memory module slot.
Reverse this procedure to install a memory module.
44
Chapter 4 Removal and replacement procedures
Optical drive
NOTE:
All optical drive spare part kits include an optical drive bezel.
Description
spare part numbers
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe (PATA)
500018-001
DVD/CD-RW Combo Drive (PATA)
500017-001
DVD-ROM Drive (PATA)
500016-001
DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe (SATA
506010-001
DVD/CD-RW Combo Drive (SATA)
506011-001
DVD-ROM Drive (SATA)
495387-001
Before removing the optical drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
Remove the optical drive:
1.
Position the computer with the right side toward you.
2.
Remove the slotted Torx ST8M2.5×7.0 screw (1) that secures the optical drive to the computer.
3.
Insert a flat-bladed screwdriver or similar tool into the optical drive tab access (2) and press the
tab to the left to release the optical drive from the computer.
4.
Remove the optical drive (3) from the computer.
Component replacement procedures
45
5.
If it is necessary to replace the optical drive bracket, position the optical drive with the rear toward
you.
6.
Remove the two Phillips PM2.0×4.0 screws (1) that secure the optical drive bracket to the optical
drive.
7.
Remove the optical drive bracket (2).
Reverse this procedure to reassemble and install an optical drive.
46
Chapter 4 Removal and replacement procedures
Switch cover and keyboard
Description
spare part numbers
Switch cover (includes button board and cable)
500001-001
Keyboards for use in the following countries or regions:
Brazil
499999-201
Taiwan
499999-AB1
Japan
499999-291
Thailand
499999-281
Korea
499999-AD1
The United States
499999-001
Latin America
499999–161
Before removing the switch cover and keyboard, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
Remove the switch cover and keyboard:
1.
Remove the following screws:
(1) Two slotted Torx ST8M2.5×7.0 screws
(2) Two Torx T8M2.5×3.0 broad-head screws
Component replacement procedures
47
48
2.
Remove the two slotted Torx ST8M2.5×7.0 screws that secure the keyboard to the computer.
3.
Turn the computer display-side up, with the front toward you.
4.
Open the computer as far as possible.
5.
Lift the switch cover (1) straight up until it disengages from the computer, and slide it back (2) until
it rests on the display assembly.
Chapter 4 Removal and replacement procedures
6.
Lift the rear edge of the keyboard (1) until it rests at an angle, and slide it back (2) until it rests on
the display assembly and switch cover.
7.
Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and
disconnect the keyboard cable (2) from the system board.
8.
Remove the keyboard.
Component replacement procedures
49
9.
Release the ZIF connector (1) to which the button board cable is attached, and disconnect the
button board cable (2) from the system board.
10. Remove the switch cover.
Reverse this procedure to install the switch cover and keyboard.
50
Chapter 4 Removal and replacement procedures
Speaker
Description
Spare part number
Speaker
456593-001
Before removing the speaker, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the keyboard (see Switch cover and keyboard on page 47).
6.
Remove the switch cover (see Switch cover and keyboard on page 47).
Remove the speaker:
1.
Disconnect the speaker cable (1) from the system board.
2.
Remove the two Torx T8M2.5×4.0 screws (2) that secure the speaker to the top cover.
3.
Remove the speaker (3) from the top cover.
Reverse this procedure to install the speaker.
Component replacement procedures
51
Display lid switch module
NOTE:
The display lid switch module is included in the Cable Kit, spare part number 457400-001.
Before removing the display lid switch module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the keyboard (see Switch cover and keyboard on page 47).
6.
Remove the switch cover (see Switch cover and keyboard on page 47).
Remove the display lid switch module:
1.
Disconnect the display lid switch module cable (1) from the system board.
2.
Remove the display lid switch module (2) from the clip built into the top cover.
3.
Remove the display lid switch module cable from the clips (3) built into the top cover.
Reverse this procedure to install the display lid switch module.
52
Chapter 4 Removal and replacement procedures
Display assembly
NOTE:
All display assembly spare part kits include 2 WLAN antenna transceivers and cables.
Description
Spare part number
14.1-inch, WXGA BrightView display assembly for use with HP 540 models
500004-001
14.1-inch, WXGA BrightView display assembly for use with HP 541 models
517616-001
Before removing the display assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Disconnect the wireless antenna cables from the WLAN module (see WLAN module on page 40).
6.
Remove the following components:
a.
Keyboard (see Switch cover and keyboard on page 47)
b.
Switch cover (see Switch cover and keyboard on page 47)
c.
Speaker (see Speaker on page 51)
d.
Display lid switch module (see Display lid switch module on page 52)
Remove the display assembly:
1.
Close the computer and turn it upside down, with the rear panel toward you.
2.
Remove the two slotted Torx ST8M2.5×7.0 screws that secure the display assembly to the
computer.
Component replacement procedures
53
3.
Turn the computer right-side up, with the front toward you.
4.
Open the computer as far as possible.
5.
Disconnect the display panel cables (1) and (2) from the system board.
6.
Remove the wireless antenna cables (3) from the clips and routing channels built into the top cover.
7.
Remove the two T8M2.5×7.0 screws (1) that secure the display assembly to the computer.
CAUTION: Support the display assembly when removing the following screws. Failure to support
the display assembly can result in damage to the display assembly and other computer
components.
8.
54
Lift the display assembly (2) straight up and remove it.
Chapter 4 Removal and replacement procedures
9.
If it is necessary to replace the display bezel, display inverter, or display hinges, remove the eight
rubber screw covers (1) and the eight Torx T8M2.5×6.0 screws (2) that secure the display bezel
to the display assembly. The rubber screw covers are available in the Rubber Kit, spare part number
500132-001.
10. Flex the inside edges of the left and right sides (1) and the top and bottom sides (2) of the display
bezel until the bezel disengages from the display enclosure.
11. Remove the display bezel (3). The display bezel is available using spare part number
500000-001.
12. If it is necessary to replace the display inverter, remove the inverter (1) from the display enclosure
as far as the display panel cable and the backlight cable will allow.
Component replacement procedures
55
13. Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter.
14. Remove the display inverter. The display inverter is available using spare part number
456618-001.
15. If it is necessary to replace the display hinges, remove the two Torx T8M2.5×6.0 screws (1) that
secure the display panel to the display enclosure.
16. Remove the display panel (2).
17. Remove the four Phillips PM2.0×4.0 screws (1) that secure each display hinge to the display
panel.
56
Chapter 4 Removal and replacement procedures
18. Remove the display hinges (2). The left and right display hinges are available using spare part
number 456619-001.
Reverse this procedure to reassemble and install the display assembly.
Component replacement procedures
57
Top cover
NOTE:
cable.
The top cover includes the TouchPad board and cable, and the TouchPad button board and
Description
Spare part number
Top cover
500002-001
Before removing the top cover, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
Remove the top cover:
1.
58
Turn the computer upside down, with the front toward you.
Chapter 4 Removal and replacement procedures
2.
Remove the followng screws:
(1) Three Phillips PM2.0×2.0 broad-head screws
(2) Seven slotted Torx ST8M2.5×7.0 screws
(3) One Torx T8m2.5×4.0 screw
3.
Turn the computer right-side up, with the left side toward you.
4.
Press in on the ExpressCard slot eject button (1) two times. The first press releases the
ExpressCard slot eject button. The second press releases the ExpressCard slot protective insert
from the ExpressCard slot.
5.
Remove the ExpressCard slot insert (2).
6.
Remove the two slotted Torx ST8M2.5×7.0 screws (3) that secure the top cover to the computer.
7.
Lift the rear edge of the top cover (1) and swing it up and forward until it rests at an angle.
8.
Lift the front edge of the top cover (2) until it disengages from the base enclosure.
9.
Tilt the top cover (3) back until the TouchPad cable is accessible.
Component replacement procedures
59
10. Release the ZIF connector (4) to which the TouchPad cable is connected and disconnect the
TouchPad cable (5) from the system board.
11. Remove the top cover.
Reverse this procedure to install the top cover.
60
Chapter 4 Removal and replacement procedures
TouchPad board and TouchPad button board
NOTE: The top cover, spare part number 500002-001, includes the TouchPad board and cable, and
the TouchPad button board and cable.
Before removing the TouchPad board and TouchPad button board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
Remove the TouchPad board and TouchPad button board:
1.
Turn the top cover upside down, with the front toward you.
2.
Release the ZIF connectors on the TouchPad button board (1) and TouchPad board (2) to which
the TouchPad board cable is connected.
3.
Disconnect and remove the TouchPad board cable (3).
Component replacement procedures
61
62
4.
Remove the two Phillips PM2.0×4.0 screws (4) that secure the TouchPad bracket to the computer.
5.
Release the TouchPad bracket (1) by sliding it back.
6.
Remove the TouchPad bracket (2) by lifting it straight up.
7.
Remove the TouchPad button board (3).
8.
Remove the TouchPad button board cable (4) from the opening in the TouchPad bracket.
Chapter 4 Removal and replacement procedures
9.
Remove the TouchPad board (1) from the top cover.
NOTE: When replacing the TouchPad board and TouchPad button board, be sure the TouchPad
button actuators (2) are installed in the top cover.
Reverse this procedure to install the TouchPad board and TouchPad button board.
Component replacement procedures
63
Bluetooth module
NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth
module cable is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 20
for more Cable Kit spare part number information.
Description
Spare part number
For use in all countries and regions except Japan and Asia Pacific countries and regions
398393-001
For use only in Japan and Asia Pacific countries and regions
450066-001
Before removing the Bluetooth module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
Remove the Bluetooth module:
64
1.
Disconnect the Bluetooth module cable (1) from the system board.
2.
Remove the two Phillips PM2.0×4.0 screws (2) that secure the Bluetooth module to the base
enclosure.
Chapter 4 Removal and replacement procedures
3.
Remove the Bluetooth module (3) from the base enclosure.
Reverse this procedure to install the Bluetooth module.
Component replacement procedures
65
System board
NOTE:
All system board spare part kits include the ExpressCard assembly.
NOTE: All system board spare part kits include replacement thermal material. Replacement thermal
material is also available in the Thermal Material Kit, spare part numbers 456605-001 and 456606-001.
Description
Spare part number
For use only with computer models equipped with Intel Core2 Duo processors and UMA graphics
subsystem
495410-001
For use only with computer models equipped with Intel Celeron M processors and UMA graphics
subsystem
495395-001
For use only with computer models equipped with discrete graphics subsystem
509115-001
For use only with computer models equipped with discrete graphics subsystem
509116-001
Before removing the system board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
66
●
Memory module (see Memory module on page 43)
●
WLAN module (see WLAN module on page 40)
●
Processor (see Processor on page 74)
Chapter 4 Removal and replacement procedures
Remove the system board:
1.
Remove the RJ-11 jack (1) from the clip built into the base enclosure and remove the RJ-11 jack
cable from the hook (2) built into the base enclosure.
2.
Disconnect the fan cable (3) and the Bluetooth module cable (4) from the system board.
3.
Remove the two Phillips PM2.0×6.0 screws (1) and the Torx T8M2.5×4.0 screw (2) that secure the
system board to the base enclosure.
4.
Flex the left side of the base enclosure (1) until the external monitor connector (2) is clear of the
opening in the base enclosure.
5.
Lift the rear edge of the system board (3) until it rests at an angle.
Component replacement procedures
67
6.
Remove the system board (4) from the base enclosure by sliding it back.
Reverse the preceding procedure to install the system board.
68
Chapter 4 Removal and replacement procedures
Fan
Description
Spare part number
Fan
431312-001
Before removing the fan, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
i.
System board (see System board on page 66)
Remove the fan:
1.
Remove the two Phillips PM2.5×7.0 screws (1) that secure the fan to the base enclosure.
Component replacement procedures
69
2.
Remove the fan (2) from the base enclosure.
Reverse this procedure to install the fan.
NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left side
of the computer.
The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is
designed to turn on automatically when high temperature conditions exist. These conditions are affected
by high external temperatures, system power consumption, power management/battery conservation
configurations, battery fast charging, and software requirements. Exhaust air is displaced through the
ventilation grill located on the left side of the computer.
70
Chapter 4 Removal and replacement procedures
Heat sink
NOTE: The heat sink spare part kits include replacement thermal material. Replacement thermal
material is also available in the Thermal Material Kit, spare part numbers 456605-001 and 456606-001.
Description
Spare part number
For use only with computer models equipped with UMA graphics subsystem
456605-001
For use only with computer models equipped with discrete graphics subsystem
456606-001
Before removing the heat sink, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
i.
System board (see System board on page 66)
Remove the heat sink:
1.
Turn the system board upside down, with the USB connectors toward you.
NOTE: Steps 2 and 3 apply only to computer models equipped with graphics subsystems having
discrete memory. See steps 4 and 5 for removing the heat sink on computer models with graphics
subsystems having UMA memory.
2.
Following the 1, 2, 3, 4, 5, 6 sequence stamped into the heat sink, loosen the six Phillips
PM2.5×10.0 screws (1) that secure the heat sink to the system board.
Component replacement procedures
71
3.
Remove the heat sink (2).
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink (1),
(2), and (3), and the system board components (4), (5), and (6) each time the heat sink is removed.
Thermal pads and thermal paste must be installed on all surfaces before the heat sink assembly
is reinstalled. Replacement thermal material is included with all heat sink, system board, and
processor spare part kits.
NOTE: Steps 4 and 5 apply only to computer models equipped with graphics subsystems with
UMA memory.
4.
72
Following the 1, 2, 3, 4, sequence stamped into the heat sink, loosen the four Phillips PM2.5×10.0
screws (1) that secure the heat sink to the system board.
Chapter 4 Removal and replacement procedures
5.
Remove the heat sink (2).
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink (1)
and (2), and the system board (3) and (4) each time the heat sink is removed. Thermal pads and
thermal paste must be installed on all surfaces before the heat sink assembly is reinstalled.
Replacement thermal material is included with all heat sink, system board, and processor spare
part kits.
Reverse this procedure to install the heat sink.
Component replacement procedures
73
Processor
NOTE: All processor spare part kits include replacement thermal material. Replacement thermal
material is also available in the Thermal Material Kit, spare part numbers 456605-001 and 456606-001.
Description
Spare part number
Intel Core2 Duo processors
●
T5470 1.60-GHz processor (2-MB L2 cache, 800-MHz FSB)
500007-001
●
T5270 1.40-GHz processor (2-MB L2 cache, 800-MHz FSB)
500005-001
Intel Celeron M processors
●
P550 2.0-GHz (1-MB L2 cache, 533-MHz FSB)
508757-001
●
P530 1.73-GHz processor (1-MB L2 cache, 533-MHz FSB)
500006-001
Intel Celeron M Dual Core processors
●
T1400 1.73-GHz (1-MB L2 cache, 533-MHz FSB)
506448-001
Before removing the processor, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
i.
System board (see System board on page 66)
Remove the processor:
74
1.
Turn the system board upside down, with the USB connectors toward you.
2.
Use a flat-bladed screwdriver to turn the processor locking screw (1) one-half turn counterclockwise
until you hear a click.
Chapter 4 Removal and replacement procedures
3.
Lift the processor (2) straight up and remove it.
NOTE: When you install the processor, the gold triangle (3) on the processor must be aligned
with the triangle (4) embossed on the processor socket.
Reverse this procedure to install the processor.
Component replacement procedures
75
Modem module
NOTE: The modem module spare part kits do not include a modem module cable. The modem module
cable is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 20 for more
Cable Kit spare part number information.
Description
Spare part number
For use only in the United States
461749-001
For use only in Japan and Asia Pacific countries and regions
461749-011
Before removing the modem module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
i.
System board (see System board on page 66)
Remove the modem module:
76
1.
Turn the system board upside down, with the USB connectors toward you.
2.
Remove the two Phillips PM2.5×4.0 screws (1) that secure the modem module to the system board.
Chapter 4 Removal and replacement procedures
3.
Lift the modem module (2) straight up to disconnect it from the system board.
4.
Remove the modem module.
Reverse this procedure to install the modem module.
Component replacement procedures
77
RTC battery
NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all
passwords and CMOS settings to be cleared.
Description
Spare part number
RTC battery
449137-001
Before removing the RTC battery, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
i.
System board (see System board on page 66)
Remove the RTC battery:
1.
78
Turn the system board upside down, with the audio connectors toward you.
Chapter 4 Removal and replacement procedures
2.
Remove the RTC battery from the socket on the system board.
Reverse this procedure to install the RTC battery.
ExpressCard assembly
NOTE:
All system board spare part kits include the ExpressCard assembly.
Before removing the ExpressCard assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
i.
System board (see System board on page 66)
Component replacement procedures
79
Remove the ExpressCard assembly:
1.
Turn the system board upside down, with the USB connectors toward you.
2.
Remove the two Phillips PM2.0×8.0 screws (1) and the two Phillips PM2.0×4.0 screws (2) that
secure the ExpressCard assembly to the system board.
3.
Turn the system board right-side up, with the USB connectors toward you.
4.
Remove the ExpressCard assembly from the system board.
Reverse this procedure to install the ExpressCard assembly.
80
Chapter 4 Removal and replacement procedures
5
Computer Setup
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system
is not working or will not load.
NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your
computer.
NOTE: Pointing devices are not supported in Computer Setup. You must use the keyboard to navigate
and make selections.
NOTE: An external keyboard connected by USB can be used with Computer Setup only if USB legacy
support is enabled.
To start Computer Setup, follow these steps:
1.
Turn on or restart the computer.
2.
Before Windows opens and while the “F10=ROM Based Setup” message is displayed in the lowerleft corner of the screen, press f10.
Starting Computer Setup
81
Using Computer Setup
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and
System Configuration menus.
1.
Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the
"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.
Because Computer Setup is not Windows-based, it does not support the TouchPad. Navigation
and selection are by keystroke:
●
To choose a menu or a menu item, use the arrow keys.
●
To select an item, press enter.
●
To close open dialog boxes and return to the main Computer Setup screen, press esc.
●
To view navigation information, press f1.
●
To change the language, press f2.
2.
Select the File, Security, Diagnostics, or System Configuration menu.
3.
To exit Computer Setup, choose one of the following methods:
●
To exit Computer Setup without saving your preferences, use the arrow keys to select File >
Ignore Changes and Exit. Then follow the instructions on the screen.
●
To save your preferences and exit Computer Setup, use the arrow keys to select File > Save
Changes and Exit. Then follow the instructions on the screen.
Your preferences go into effect when the computer restarts.
Restoring factory settings in Computer Setup
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1.
Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the
"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.
2.
Use the arrow keys to select File > Restore defaults, and then press enter.
3.
When the confirmation dialog box opens, press f10.
4.
To save your preferences and exit Computer Setup, use the arrow keys to select File > Save
Changes and Exit. Then follow the instructions on the screen.
Your preferences go into effect when the computer restarts.
NOTE: Your password settings and security settings are not changed when you restore the factory
settings.
82
Chapter 5 Computer Setup
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by your
computer.
File menu
Select
To do this
System information
●
View identification information for the computer and the
batteries in the system.
●
View specification information for the processor, cache
and memory size, system ROM, video revision, and
keyboard controller version.
Restore defaults
Replace the configuration settings in Computer Setup with the
original factory settings. (Password settings and security
settings are not changed when you restore the factory
settings.)
Ignore changes and exit
Cancel any changes entered during the current session. Then
exit and restart the computer.
Save changes and exit
Save any changes entered during the current session. Then
exit and restart the computer. Your changes go into effect
when the computer restarts.
Computer Setup menus
83
Security menu
Select
To do this
Setup password
Enter, change, or delete a setup password.
Power-On password
Enter, change, or delete a power-on password.
Password options
●
Enable/disable stringent security.
●
Enable/disable password requirement on computer
restart.
●
Enable/disable DriveLock on any computer hard drive
and on optional MultiBay hard drives.
●
Change a DriveLock user password or master password.
DriveLock passwords
NOTE: DriveLock settings are accessible only when you
enter Computer Setup by turning on (not restarting) the
computer.
System IDs
Enter user-defined computer asset tracking number and
ownership tag.
Disk Sanitizer
Run Disk Sanitizer to destroy all existing data on the primary
hard drive. The following options are available:
●
Fast: Runs the Disk Sanitizer erase cycle once.
●
Optimum: Runs the Disk Sanitizer erase cycle 3 times.
●
Custom: Allows you to select the desired number of Disk
Sanitizer erase cycles from a list.
CAUTION: If you run Disk Sanitizer, the data on the primary
hard drive is destroyed permanently.
Diagnostics menu
84
Select
To do this
Hard Drive Self-Test options
Run a comprehensive self-test on any hard drive in the system
or on any optional MultiBay hard drive.
Memory Check
Run a comprehensive check on system memory.
Startup Check (select models only)
Verify the system components needed for starting the
computer.
Chapter 5 Computer Setup
System Configuration menu
NOTE:
Some of the listed System Configuration options may not be supported by your computer.
Select
To do this
Language (or press f2)
Change the Computer Setup language.
Boot options
●
Set f9, f10, and f12 delay when starting up.
●
Enable/disable CD-ROM boot.
●
Enable/disable floppy boot.
●
Enable/disable internal network adapter boot and set the
boot mode (PXE or RPL).
●
Enable/disable MultiBoot, which sets a boot order that
can include most boot devices in the system.
●
Set the Express Boot Popup delay in seconds.
●
Set the boot order.
●
Swap the functions of the fn key and left ctrl key.
●
Enable/disable multiple standard pointing devices at
startup. (To set the computer to support only a single,
usually nonstandard, pointing device at startup, select
Disable.)
●
Enable/disable USB legacy support. When enabled, USB
legacy support allows the following:
Device configurations
◦
Use of a USB keyboard, mouse, and hub in
Computer Setup even when a Windows operating
system is not running.
◦
Startup from bootable USB devices, including a hard
drive, diskette drive, or optical drive connected by a
Computer Setup menus
85
Select
To do this
USB port to the computer or to an optional docking
device (select models only).
86
Chapter 5 Computer Setup
●
Select a parallel port mode: EPP (Enhanced Parallel
Port), standard, bidirectional, or ECP (Enhanced
Capabilities Port).
●
Enable/disable BIOS DMA data transfers.
●
Enable/disable fan always on while connected to an AC
outlet.
●
Enable/disable Intel Data Execution Prevention or AMD®
PSAE Execution Disable. When enabled, the processor
can disable some virus code execution, which helps to
improve computer security.
●
Enable/disable LAN Power Save. When enabled, saves
power by turning off the LAN when not in use.
●
Enable/disable SATA Native Mode.
●
Enable/disable Dual Core CPU.
●
Enable/disable Secondary Battery Fast Charge.
●
Choose Bit-shift or LBA assisted HDD Translation Mode.
●
Enable/disable Windows direct application launcher.
●
Enable/disable HP Lockout.
Select
To do this
Built-In Device Options
●
Enable/disable embedded WWAN Device Radio.
●
Enable/disable embedded WLAN Device Radio.
●
Enable/disable embedded Bluetooth® Device Radio.
●
Enable/disable LAN/WLAN Switching. When enabled,
switches to a WLAN when a LAN is either unavailable or
disconnected.
●
Enable/disable Wake on LAN from Off.
●
Enable/disable the ambient light sensor.
●
Enable/disable the serial port.
●
Enable/disable the parallel port.
●
Enable/disable the flash media reader.
●
Enable/disable the USB port.
Port Options
CAUTION: Disabling the USB port also disables
MultiBay devices and ExpressCard devices on the
advanced port replicator.
●
Enable/disable the 1394 port.
●
Enable/disable the cardbus slot.
●
Enable/disable the ExpressCard slot.
●
Enable/disable the infrared port.
●
Enable/disable the optical disk drive.
●
Enable/disable the network controller.
Computer Setup menus
87
6
Specifications
Computer specifications
Metric
U.S.
Depth
24.64 cm
9.70 in
Width
33.80 cm
13.31 in
Height (front to rear)
3.08 to 3.43 cm
1.21 to 1.35 in
Weight (equipped with optical drive, hard drive, and battery)
2.20 kg
4.85 lbs
Dimensions
Input power
Operating voltage
19.0 V dc @ 4.74 A – 90 W
Operating current
4.74 A
Temperature
Operating (not writing to optical disc)
0°C to 35°C
32°F to 95°F
Operating (writing to optical disc)
5°C to 35°C
41°F to 95°F
Nonoperating
-20°C to 60°C
-4°F to 140°F
Relative humidity
Operating
10% to 90%
Nonoperating
5% to 95%
Maximum altitude (unpressurized)
Operating
-15 m to 3,048 m
-50 ft to 10,000 ft
Nonoperating
-15 m to 12,192 m
-50 ft to 40,000 ft
Shock
Operating
125 g, 2 ms, half-sine
Nonoperating
200 g, 2 ms, half-sine
Random vibration
Operating
88
Chapter 6 Specifications
0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate
Metric
Nonoperating
U.S.
1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
range of temperatures.
14.1-inch, WXGA display specifications
Metric
U.S.
Height
27.94 cm
11.0 in
Width
20.83 cm
8.2 in
Diagonal
35.56 cm
14.1 in
Number of colors
Up to 16.8 million
Contrast ratio
250:1 (typical)
Brightness
180 nits (typical)
Dimensions
Pixel resolution
Pitch
0.279 × 0.279 mm
Format
1280 × 800
Configuration
RGB vertical stripe
Backlight
Edge lit
Character display
80 × 25
Total power consumption
4.0 W
Viewing angle
+/-40 horizontal, +20/–40° vertical (typical)
14.1-inch, WXGA display specifications
89
Hard drive specifications
250-GB*
120-GB*
80-GB*
Height
9.5 mm
9.5 mm
9.5 mm
Width
70 mm
70 mm
70 mm
Weight
101 g
101 g
101 g
Interface type
SATA
SATA
SATA
Transfer rate
100 MB/sec
100 MB/sec
100 MB/sec
Security
ATA security
ATA security
ATA security
Single track
3 ms
3 ms
3 ms
Average
13 ms
13 ms
13 ms
Maximum
24 ms
24 ms
24 ms
Logical blocks
488,397,168
234,420,480
156,280,320
Disc rotational speed
5400 rpm
5400 rpm
5400 rpm
Dimensions
Seek times (typical read, including setting)
Operating temperature
5°C to 55°C (41°F to 131°F)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive
specifications may differ slightly.
NOTE: Certain restrictions and exclusions apply. Contact technical support for details.
90
Chapter 6 Specifications
DVD±RW and CD-RW Double-Layer Combo Drive
specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CDROM, CD-ROM XA, MIXED MODE CD, CD-I,
CD-I Bridge (Photo-CD, Video CD), Multisession
CD (Photo-CD, CD-EXTRA, Portfolio, CD-R, CDRW), CD-R, CD-RW, DVD-ROM (DVD-5,
DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD-RAM
CD-R and CD-RW
Access time
CD
DVD
Random
< 175 ms
< 230 ms
Cache buffer
2 MB
DVD+R, DVD+RW, DVD-R, DVDRW, DVD-RAM
Data transfer rate
24X CD-ROM
3,600 KB/sec
8X DVD-ROM
10,800 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
4X DVD+RW
5,400 KB/sec
8X DVD-R
10,800 KB/sec
4X DVD-RW
5,400 KB/sec
2.4X DVD+R(9)
2,700 KB/sec
5X DVD-RAM
6,750 KB/sec
Transfer mode
Multiword DMA Mode
DVD±RW and CD-RW Double-Layer Combo Drive specifications
91
DVD/CD-RW Combo Drive specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CDROM, CD-ROM XA, MIXED MODE CD, CD-I,
CD-I Bridge (Photo-CD, Video CD), Multisession
CD (Photo-CD, CD-EXTRA, Portfolio, CD-R, CDRW), CD-R, CD-RW, DVD-ROM (DVD-5,
DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD-RAM
CD-R and CD-RW
Access time
CD
DVD
Random
< 110 ms
< 130 ms
Cache buffer
2 MB
Data transfer rate
92
24X CD-ROM
3,600 KB/sec
8X DVD
3,600 KB/sec
24X CD-R
3,600 KB/sec
24X CD-RW
3,600 KB/sec
Transfer mode
Multiword DMA mode 2
Chapter 6 Specifications
System DMA specifications
Hardware DMA
System function
DMA0
Not applicable
DMA1*
Not applicable
DMA2*
Not applicable
DMA3
Not applicable
DMA4
Direct memory access controller
DMA5*
Available for ExpressCard
DMA6
Not assigned
DMA7
Not assigned
*ExpressCard controller can use DMA 1, 2, or 5.
System DMA specifications
93
System interrupt specifications
Hardware IRQ
System function
IRQ0
System timer
IRQ1
Standard 101-/102-Key or Microsoft Natural Keyboard
IRQ2
Cascaded
IRQ3
Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD
IRQ4
COM1
IRQ5*
Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax
Modem with SmartCP
IRQ6
Diskette drive
IRQ7*
Parallel port
IRQ8
System CMOS/real-time clock
IRQ9*
Microsoft ACPI-compliant system
IRQ10*
Intel USB UHCI controller—24C2
Intel 82852/82855 GM/GME Graphic Controller
Realtek RTL8139 Family PCI Fast Ethernet Controller
IRQ11
Intel USB EHCI controller—24CD
Intel USB UHCI controller—24C4
Intel USB UHCI controller—24C7
Intel Pro/Wireless 2200BG
TI OHCI 1394 host controller
TI PCI1410 CardBus controller
IRQ12
Synaptics PS/2 TouchPad
IRQ13
Numeric data processor
IRQ14
Primary IDE channel
IRQ15
Secondary IDE channel
*Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
NOTE: ExpressCards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial
port may assert IRQ3 or IRQ4.
94
Chapter 6 Specifications
System I/O address specifications
I/O address (hex)
System function (shipping configuration)
000 - 00F
DMA controller no. 1
010 - 01F
Unused
020 - 021
Interrupt controller no. 1
022 - 024
Opti chipset configuration registers
025 - 03F
Unused
02E - 02F
87334 “Super I/O” configuration for CPU
040 - 05F
Counter/timer registers
044 - 05F
Unused
060
Keyboard controller
061
Port B
062 - 063
Unused
064
Keyboard controller
065 - 06F
Unused
070 - 071
NMI enable/RTC
072 - 07F
Unused
080 - 08F
DMA page registers
090 - 091
Unused
092
Port A
093 - 09F
Unused
0A0 - 0A1
Interrupt controller no. 2
I/O Address (hex)
System Function (shipping configuration)
0A2 - 0BF
Unused
0C0 - 0DF
DMA controller no. 2
0E0 - 0EF
Unused
0F0 - 0F1
Coprocessor busy clear/reset
0F2 - 0FF
Unused
100 - 16F
Unused
170 - 177
Secondary fixed disk controller
178 - 1EF
Unused
1F0 - 1F7
Primary fixed disk controller
1F8 - 200
Unused
201
JoyStick (decoded in ESS1688)
202 - 21F
Unused
System I/O address specifications
95
96
I/O address (hex)
System function (shipping configuration)
220 - 22F
Entertainment audio
230 - 26D
Unused
26E - 26
Unused
278 - 27F
Unused
280 - 2AB
Unused
2A0 - 2A7
Unused
2A8 - 2E7
Unused
2E8 - 2EF
Reserved serial port
2F0 - 2F7
Unused
2F8 - 2FF
Infrared port
300 - 31F
Unused
320 - 36F
Unused
370 - 377
Secondary diskette drive controller
378 - 37F
Parallel port (LPT1/default)
380 - 387
Unused
388 - 38B
FM synthesizer—OPL3
38C - 3AF
Unused
3B0 - 3BB
VGA
3BC - 3BF
Reserved (parallel port/no EPP support)
3C0 - 3DF
VGA
3E0 - 3E1
ExpressCard controller in CPU
3E2 - 3E3
Unused
3E8 - 3EF
Internal modem
3F0 - 3F7
“A” diskette controller
3F8 - 3FF
Serial port (COM1/default)
CF8 - CFB
PCI configuration index register (PCIDIVO-1)
CFC - CFF
PCI configuration data register (PCIDIVO-1)
Chapter 6 Specifications
System memory map specifications
Size
Memory address
System function
640 KB
00000000-0009FFFF
Base memory
128 KB
000A0000-000BFFFF
Video memory
48 KB
000C0000-000CBFFF
Video BIOS
160 KB
000C8000-000E7FFF
Unused
64 KB
000E8000-000FFFFF
System BIOS
15 MB
00100000-00FFFFFF
Extended memory
58 MB
04800000-07FFFFFF
Super extended memory
58 MB
04800000-07FFFFFF
Unused
2 MB
08000000-080FFFFF
Video memory (direct access)
4 GB
08200000-FFFEFFFF
Unused
64 KB
FFFF0000-FFFFFFFF
System BIOS
System memory map specifications
97
7
Screw listing
This section provides specification and reference information for the screws and screw locks used in
the computer. All screws listed in this section are available in the Screw Kit, spare part number
500130-001.
98
Chapter 7 Screw listing
Phillips PM2.0×5.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
4
5.0 mm
2.0 mm
5.0 mm
Where used:
(1) Two captive screws that secure the hard drive bay cover to the computer (screws are captured on
the cover by C-clips)
(2) One captive screw that secures the WLAN module compartment cover to the computer (screw is
captured on the cover by a C-clip)
(3) One captive screw that secures the memory module compartment cover to the computer (screw is
captured on the cover by a C-clip)
Phillips PM2.0×5.0 captive screw
99
Phillips PM2.5×12.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
1
12.0 mm
2.5 mm
5.0 mm
Where used: One captive screw that secures the hard drive to the computer (screw is secured to the
hard drive bracket)
100 Chapter 7 Screw listing
Phillips PM3.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
4
4.0 mm
3.0 mm
5.0 mm
Where used: 4 screws that secure the hard drive bracket to the hard drive
Phillips PM3.0×4.0 screw 101
Phillips PM2.5×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
4
4.0 mm
2.5 mm
5.0 mm
Where used: 2 screws that secure the WLAN module to the system board
Where used: 2 screws that secure the modem module to the system board
102 Chapter 7 Screw listing
Slotted Torx ST8M2.5×7.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
18
7.0 mm
2.5 mm
5.0 mm
Where used:
(1) One screw that secures the optical drive to the computer
(2) Two screws that secure the keyboard to the computer
(3) Two screws that secure the switch cover to the computer
Slotted Torx ST8M2.5×7.0 screw 103
Where used: 2 screws that secure the display assembly to the computer
Where used: 2 screws that secure the display assembly to the computer
Where used: 7 screws that secure the top cover to the base enclosure
104 Chapter 7 Screw listing
Where used: 2 screws that secure the top cover to the base enclosure
Slotted Torx ST8M2.5×7.0 screw 105
Phillips PM2.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
16
4.0 mm
2.0 mm
4.5 mm
Where used: 2 screws that secure the optical drive bracket to the optical drive
Where used: 8 screws that secure the display hinges to the display assembly
106 Chapter 7 Screw listing
Where used: 2 screws that secure the TouchPad bracket and TouchPad button board to the top cover
Where used: 2 screws that secure the Blueotooth module to the base enclosure
Where used: 2 screws that secure the ExpressCard assembly to the system board
Phillips PM2.0×4.0 screw 107
Torx T8M2.5×3.0 broad-head screw
Color
Quantity
Length
Thread
Head diameter
Black
2
3.0 mm
2.5 mm
8.0 mm
Where used: 2 screws that secure the switch cover to the computer
108 Chapter 7 Screw listing
Torx T8M2.5×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
3
4.0 mm
2.5 mm
5.0 mm
Where used: 2 screws that secure the speaker to the computer
Where used: One screw that secures the top cover to the base enclosure
Torx T8M2.5×4.0 screw 109
Torx T8M2.5×6.0 screw
Color
Quantity
Length
Thread
Heat width
Black
9
6.0 mm
2.5 mm
5.0 mm
Where used: 8 screws that secure the display bezel to the display assembly
Where used: One screw that secures the system board to the base enclosure
110 Chapter 7 Screw listing
Phillips PM2.0×2.0 broad-head screw
Color
Quantity
Length
Thread
Head diameter
Black
3
2.0 mm
2.0 mm
7.0 mm
Where used: 3 screws that secure the top cover to the display enclosure
Phillips PM2.0×2.0 broad-head screw 111
Phillips PM2.0×6.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
1
6.0 mm
2.0 mm
4.5 mm
Where used: One screw that secures the system board to the base enclosure
112 Chapter 7 Screw listing
Phillips PM2.5×7.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
1
7.0 mm
2.5 mm
5.0 mm
Where used: One screw that secures the fan to the base enclosure
Phillips PM2.5×7.0 screw 113
Phillips PM2.5×7.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
1
7.0 mm
2.5 mm
5.0 mm
Where used: One captive screw that secures the fan to the base enclosure (screw is secured to the
fan by a C-clip)
114 Chapter 7 Screw listing
Phillips PM2.5×10.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
4 or 6
10.0 mm
2.5 mm
5.0 mm
Where used: 6 captive screws that secure the heat sink to the system board on computer models
equipped with discrete graphics subsystem memory (screws are secured to the heat sink by C-clips)
Phillips PM2.5×10.0 captive screw 115
Where used: 4 captive screws that secure the heat sink to the system board on computer models
equipped with UMA graphics subsystem memory (screws are secured to the heat sink by C-clips)
116 Chapter 7 Screw listing
Phillips PM2.0×8.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
2
8.0 mm
2.0 mm
4.5 mm
Where used: 2 screws that secure the ExpressCard assembly to the system board
Phillips PM2.0×8.0 screw 117
8
Backup and recovery
Backup and recovery in Windows Vista
Overview
To protect your information, use the Backup and Restore Center to back up individual files and folders,
back up your entire hard drive (select models only), or create system restore points. In case of system
failure, you can use the backup files to restore the contents of your computer.
The Backup and Restore Center provides the following options:
●
Backing up individual files and folders
●
Backing up the entire hard drive (select models only)
●
Scheduling automatic backups (select models only)
●
Creating system restore points
●
Recovering individual files
●
Restoring the computer to a previous state
●
Recovering information using recovery tools
NOTE:
For detailed instructions, perform a search for these topics in Help and Support.
NOTE: In case of system instability, HP recommends that you print the recovery procedures and save
them for later use.
Backing up your information
Recovery after a system failure is as complete as your most current backup. You should create your
initial backup immediately after software setup. As you add new software and data files, you should
continue to back up your system on a regular basis to maintain a reasonably current backup.
You can back up your information to an optional external hard drive, a network drive, or discs.
Note the following when backing up:
●
Store personal files in the Documents folder, and back it up regularly.
●
Back up templates that are stored in their associated programs.
●
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot
of your settings. The screen shot can be a time-saver if you have to reset your preferences.
118 Chapter 8 Backup and recovery
To create a screen shot:
1.
Display the screen you want to save.
2.
Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3.
Open a word-processing document, and then select Edit > Paste.
The screen image is added to the document.
4.
●
Save the document.
When backing up to discs, use any of the following types of discs (purchased separately): CD-R,
CD-RW, DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD±RW. The discs you use will depend on
the type of optical drive installed in your computer.
NOTE: DVDs and DVDs with double-layer (DL) support store more information than CDs, so
using them for backup reduces the number of recovery discs required.
●
When backing up to discs, number each disc before inserting it into the optical drive of the computer.
To create a backup using Backup and Restore Center, follow these steps:
NOTE:
Be sure that the computer is connected to AC power before you start the backup process.
NOTE: The backup process may take over an hour, depending on file size and the speed of the
computer.
1.
Select Start > All Programs > Maintenance > Backup and Restore Center.
2.
Follow the on-screen instructions to back up your entire computer (select models only) or your files.
NOTE: Windows includes the User Account Control feature to improve the security of your
computer. You may be prompted for your permission or password for tasks such as installing
software, running utilities, or changing Windows settings. Refer to Help and Support for more
information.
Performing a recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
●
Windows recovery tools: You can use the Backup and Restore Center to recover information you
have previously backed up. You can also use Windows Startup Repair to fix problems that might
prevent Windows from starting correctly.
●
f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image.
The image includes the Windows operating system and software programs installed at the factory.
NOTE: If you are unable to boot (start up) your computer, you must purchase a Windows Vista
operating system DVD to reboot the computer and repair the operating system. For additional
information, refer to the “Using a Windows Vista operating system DVD (purchased separately)” section
in this guide.
Backup and recovery in Windows Vista 119
Using the Windows recovery tools
To recover information you previously backed up, follow these steps:
1.
Click Start > All Programs > Maintenance > Backup and Restore Center.
2.
Follow the on-screen instructions to recover your entire computer (select models only) or your files.
NOTE: Windows includes the User Account Control feature to improve the security of your computer.
You may be prompted for your permission or password for tasks such as installing software, running
utilities, or changing Windows settings. Refer to Help and Support for more information.
To recover your information using Startup Repair, follow these steps:
CAUTION: Using Startup Repair completely erases hard drive contents and reformats the hard drive.
All files you have created and any software installed on the computer are permanently removed. When
reformatting is complete, the recovery process restores the operating system, as well as the drivers,
software, and utilities from the backup used for recovery.
1.
If possible, back up all personal files.
2.
If possible, check for the presence of the Windows partition and the HP Recovery partition. To find
the partitions, select Start > Computer.
NOTE: If the Windows partition and the HP Recovery partition have been deleted, you must
recover your operating system and programs using the Windows Vista operating system DVD and
the Driver Recovery disc (both purchased separately). For additional information, refer to the “Using
a Windows Vista operating system DVD (purchased separately)” section in this guide.
3.
Restart the computer, and then press f8 before the Windows operating system loads.
4.
Select Repair your computer.
5.
Follow the on-screen instructions.
NOTE: For additional information on recovering information using the Windows tools, perform a search
for these topics in Help and Support.
Using f11
CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you
have created and any software installed on the computer are permanently removed. The f11 recovery
tool reinstalls the operating system and HP programs and drivers that were installed at the factory.
Software not installed at the factory must be reinstalled.
To recover the original hard drive image using f11, follow these steps:
1.
If possible, back up all personal files.
2.
If possible, check for the presence of the HP Recovery partition. To find the partition, select
Start > Computer.
NOTE: If the HP Recovery partition has been deleted, you must recover your operating system
and programs using the Windows Vista operating system DVD and the Driver Recovery disc (both
purchased separately). For additional information, refer to the “Using a Windows Vista operating
system DVD (purchased separately)” section in this guide.
3.
Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
120 Chapter 8 Backup and recovery
4.
Press f11 while the “Press <F11> for recovery” message is displayed on the screen.
5.
Follow the on-screen instructions.
Using a Windows Vista operating system DVD (purchased separately)
If you are unable to boot (start up) your computer, you must purchase a Windows Vista operating system
DVD to reboot the computer and repair the operating system. Make sure that your most recent backup
(stored on discs or on an external drive) is easily accessible. To order a Windows Vista operating system
DVD, go to http://www.hp.com/support, select your country or region, and follow the on-screen
instructions. You can also order the DVD by calling technical support. For contact information, refer to
the Worldwide Telephone Numbers booklet included with the computer.
CAUTION: Using a Windows Vista operating system DVD completely erases hard drive contents and
reformats the hard drive. All files you have created and any software installed on the computer are
permanently removed. When reformatting is complete, the recovery process helps you restore the
operating system, as well as drivers, software, and utilities.
To initiate recovery using a Windows Vista operating system DVD, follow these steps:
NOTE:
This process takes several minutes.
1.
If possible, back up all personal files.
2.
Restart the computer, and then insert the Windows Vista operating system DVD into the optical
drive before the Windows operating system loads.
3.
When prompted, press any keyboard key.
4.
Follow the on-screen instructions.
5.
Click Next.
6.
Select Repair your computer.
7.
Follow the on-screen instructions.
Backup and recovery in Windows Vista 121
Backup and Recovery in Windows XP
Overview
To protect your information, use the Windows Backup utility (select models only) to back up files and
folders or create recovery points. In case of system failure, you can use the backup files to restore your
computer.
Windows provides the following options:
●
Backing up individual files and folders
●
Backing up all files and folders
●
Scheduling automatic backups
●
Creating recovery points
●
Recovering information
NOTE:
For detailed instructions, perform a search for these topics in Help and Support.
NOTE: In case of system instability, HP recommends that you print the recovery procedures and save
them for later use.
Backing up your information
Recovery after a system failure is as complete as your most current backup. You should create your
initial backup immediately after software setup. As you add new software and data files, you should
continue to back up your system on a regular basis to maintain a reasonably current backup.
You can back up individual files or folders to an optional external hard drive or to a network drive.
Note the following when backing up:
●
Store personal files in the My Documents folder, and back it up periodically.
●
Back up templates stored in their associated programs.
●
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot
of your settings. The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
a.
Display the screen you want to save.
b.
Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c.
Open a word-processing document, click Edit > Paste.
The screen image is added to the document.
d.
Save the document.
To create a backup using the Windows Backup utility (select models only), follow these steps:
122 Chapter 8 Backup and recovery
NOTE:
Be sure that the computer is connected to AC power before you start the backup process.
NOTE: The backup process may take over an hour, depending on file size and the speed of the
computer.
1.
Click Start > All Programs > Accessories > System Tools > Backup.
2.
Follow the on-screen instructions.
Performing a recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
●
Windows recovery tools (select models only): You can use the Windows Backup utility to recover
information you have previously backed up.
●
Operating System and Driver Recovery discs (included with your computer): You can use the discs
to recover your operating system and programs installed at the factory.
Recovering your information
To recover information you previously backed up, follow these steps:
1.
If possible, back up all personal files.
2.
Click Start > All Programs > Accessories > System Tools > Backup.
The Backup or Restore Wizard opens.
3.
Click Restore files and settings, and then click Next.
4.
Follow the on-screen instructions.
NOTE: For additional information on initiating a recovery in Windows, perform a search for this topic
in Help and Support.
Recovering the operating system and programs
CAUTION: The recovery process reformats and completely erases the hard drive. All files you have
created and any software installed on the computer are permanently removed. The recovery process
reinstalls the original operating system, software, and drivers. Software, drivers, and updates not
installed by HP must be manually reinstalled.
To recover your operating system and programs, follow these steps:
1.
If possible, back up all personal files.
2.
Insert the Operating System disc into the optical drive.
3.
Shut down the computer.
4.
Turn on the computer.
5.
Follow the on-screen instructions to install the operating system.
6.
After the operating system is installed, remove the Operating System disc and insert the Driver
Recovery disc.
7.
Follow the on-screen instructions to install the drivers and programs.
Backup and Recovery in Windows XP 123
9
Connector pin assignments
Audio-out (headphone)
Pin
Signal
1
Audio out, left channel
2
Audio out, right channel
3
Ground
Audio-in (microphone)
Pin
Signal
1
Audio signal in
2
Audio signal in
3
Ground
124 Chapter 9 Connector pin assignments
External monitor
Pin
Signal
1
Red analog
2
Green analog
3
Blue analog
4
Not connected
5
Ground
6
Ground analog
7
Ground analog
8
Ground analog
9
+5 VDC
10
Ground
11
Monitor detect
12
DDC 2B data
13
Horizontal sync
14
Vertical sync
15
DDC 2B clock
External monitor 125
RJ-11 (modem)
Pin
Signal
1
Unused
2
Tip
3
Ring
4
Unused
5
Unused
6
Unused
126 Chapter 9 Connector pin assignments
RJ-45 (network)
Pin
Signal
1
Transmit +
2
Transmit -
3
Receive +
4
Unused
5
Unused
6
Receive -
7
Unused
8
Unused
Universal Serial Bus
Pin
Signal
1
+5 VDC
2
Data -
3
Data +
4
Ground
RJ-45 (network) 127
10 Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the
country or region where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or
region where the computer is used.
Requirements for all countries and regions
The requirements listed below are applicable to all countries and regions:
●
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
●
All power cord sets must be approved by an acceptable accredited agency responsible for
evaluation in the country or region where the power cord set will be used.
●
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage
rating of 125 or 250 V AC, as required by the power system of each country or region.
●
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard
Sheet C13 connector for mating with the appliance inlet on the back of the computer.
128 Chapter 10 Power cord set requirements
Requirements for specific countries and regions
Country/region
Accredited agency
Applicable note number
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
METI
3
South Korea
EK
4
The Netherlands
KEMA
1
Norway
NEMKO
1
The People's Republic of China
CCC
5
Sweden
SEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
4
The United Kingdom
BSI
1
The United States
UL
2
1.
The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
2.
The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding
type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3.
The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall
plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4.
The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
5.
The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
Requirements for specific countries and regions 129
11 Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general household
waste. Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this appendix can result in damage to display components. The only
components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight.
Careful handling must be exercised when removing these components. When you remove these
components, handle them carefully.
NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly
that might require special handling at end-of-life. Disposal of mercury may be regulated because of
environmental considerations. For disposal or recycling information, contact your local authorities, or
see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).
NOTE: The procedures provided in this appendix are general disassembly instructions. Specific
details, such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from
one computer model to another.
130 Chapter 11 Recycling
Perform the following steps to disassemble the display assembly:
1.
Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly.
2.
Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the
display bezel until the bezel disengages from the display assembly.
3.
Remove the display bezel (3).
Display 131
4.
Disconnect all display panel cables (1) from the display inverter and remove the inverter (2).
5.
Remove all screws (1) that secure the display panel assembly to the display enclosure.
6.
Remove the display panel assembly (2) from the display enclosure.
7.
Turn the display panel assembly upside down.
8.
Remove all screws that secure the display panel frame to the display panel.
9.
Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display
panel frame.
132 Chapter 11 Recycling
10. Remove the display panel frame (2) from the display panel.
11. Remove the screws (1) that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover (2) and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
Display 133
15. Remove the backlight cables (1) from the clip (2) in the display panel.
16. Turn the display panel upside down.
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
17. Remove the backlight frame from the display panel.
134 Chapter 11 Recycling
18. Remove the backlight from the backlight frame.
19. Disconnect the display panel cable (1) from the LCD panel.
20. Remove the screws (2) that secure the LCD panel to the display rear panel.
21. Release the LCD panel (3) from the display rear panel.
22. Release the tape (4) that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
Display 135
Index
A
AC adapter, spare part
numbers 22, 24
AD adapter, spare part
numbers 24
antenna, disconnecting 42
antennae 13
audio, product description 4
audio-in jack
location 10
pin assignments 124
audio-out jack
location 10
pin assignments 124
B
backing up files 118
backing up files and folders
Backup and Restore Center
119
base enclosure
spare part numbers 17
base enclosure, spare part
numbers 27
battery
location 12
removal 34
spare part numbers 17,
34
battery bay 12
battery latches 12
battery light 11
Bluetooth module
removal 64
spare part numbers 17,
64
Bluetooth module cable
spare part numbers 20
boot options 85
boot order 85
136 Index
bottom components 12
button components 8
buttons
power 8
TouchPad 7
wireless 8
122
118,
27,
24,
C
Cable Kit
contents 20
spare part numbers 18, 20,
25
cables, service considerations 30
caps lock light 8
carrying case, spare part
numbers 22
chipset, product description 1
CMOS clearing 34
components
bottom 12
buttons 8
front 10
keys 9
left-side 11
lights 8
pointing devices 7
right-side 10
speaker 8
top 7
TouchPad 7
computer feet
locations 36
spare part numbers 36
Computer Setup
accessing 81
Diagnostics menu 84
File menu 83
navigating and selecting 82
restoring factory settings 82
Security menu 84
System Configuration
menu 85
using 82
computer specifications 88
connectors
power 11
service considerations 30
creating a backup 118
D
Diagnostics menu 84
discrete base enclosure
spare part numbers 17
discrete base enclosure, spare part
numbers 25
discs
Driver Recovery 123
Operating System 123
Disk Sanitizer 84
diskette drive
precautions 30
product description 3
spare part numbers 22
display assembly
removal iii
spare part numbers 16, 27,
iii
display bezel
removal 55
spare part numbers 55
display bezel, spare part
numbers 16
display component recycling 130
display enclosure, spare part
numbers 16, 27
display hinge
removal 56
spare part numbers 16, 25,
57
display inverter
removal 55
spare part numbers 16, 25,
56
display lid switch module
removal 52
spare part numbers 20, 52
display panel, removal 56
display specifications 89
DriveLock password 84
Driver Recovery disc 123
drives
boot order 85
preventing damage 30
DVD-ROM Drive
removal 45
spare part numbers 26, 27,
45
DVD-ROM drive
spare part numbers 17, 21
DVD/CD-RW Combo Drive
precautions 30
removal 45
spare part numbers 17, 21,
27, 45
specifications 92
DVD±RW and CD-RW Combo
Drive
precautions 30
spare part numbers 21
specifications 91
DVD±RW and CD-RW Super Multi
Double-Layer Combo Drive with
LightScribe
spare part numbers 27
DVD±RW and CD-RW SuperMulti
Double-Layer Combo Drive with
LightScribe
removal 45
spare part numbers 17, 45
E
electrostatic discharge 31
esc key 9
Ethernet, product description 4
Execution Disable 86
ExpressCard assembly
removal 79
spare part numbers 26, 66
ExpressCard assembly, spare part
numbers 16, 26
ExpressCard slot 11
ExpressCard slot insert,
illustrated 19
external media cards, product
description 4
external monitor port
location 11
pin assignments 125
F
f11 recovery 120
fan
removal 69
spare part numbers 16, 24,
69
feet
locations 36
spare part numbers 36
File menu 83
files and folders
backing up 122
recovering 123
fn key 9
front components 10
function keys 9
G
graphics, product description
grounding equipment and
methods 33
2
H
hard drive
location 12
precautions 30
product description 3
removal 38
spare part numbers 18, 21,
27, 38
specifications 90
hard drive bay 12
hard drive bay cover
illustrated 19
removal 38
hard drive bracket, removal 39
hard drive recovery 120
hard drive test 84
headphone jack
location 10
pin assignments 124
heat sink
removal 71
spare part numbers 16, 25,
71
hinge
removal 56
spare part numbers 16, 25,
57
I
I/O address specifications 95
interrupt specifications 94
J
jacks
audio-in 10
audio-out 10
headphone 10
microphone 10
modem 11
network 11
RJ-11 11
RJ-45 11
K
key components 9
keyboard
product description 5
removal 47
spare part numbers 16, 26,
47
keypad keys 9
keys
esc 9
fn 9
function 9
keypad 9
Windows applications 9
Windows logo 9
L
LAN Power Save 86
language, changing in Computer
Setup 85
LCD cable kit
spare part number 28
left-side components 11
legacy support, USB 81, 85
Index 137
light components 8
lights
battery 11
caps lock 8
power 9
wireless 8
Logo Kit
spare part numbers 28
Logo Kit, spare part numbers 22,
26
M
mass storage devices, spare part
numbers 21
memory check 84
memory map specifications 97
memory module
product description 2
removal 43
spare part numbers 18, 27,
43
memory module compartment 12
memory module compartment
cover
illustrated 19
removal 43
microphone jack
location 10
pin assignments 124
model name 1
modem jack
location 11
pin assignments 126
modem module
product description 4
removal 76
spare part numbers 17, 25,
26, 76
monitor port
location 11
pin assignments 125
N
network jack
location 11
pin assignments 127
O
Operating System disc 123
operating system, product
description 5
138 Index
optical drive
location 10
precautions 30
product description 3
removal 45
spare part numbers 17, 21,
45
specifications 91, 92
P
packing guidelines 32
panels, product description 2
parallel port mode 86
password clearing 34
passwords 84
pin assignments
audio-in jack 124
audio-out jack 124
external monitor port 125
headphone jack 124
microphone jack 124
modem jack 126
monitor port 125
network jack 127
RJ-11 126
RJ-45 jack 127
Universal Serial Bus (USB)
port 127
plastic parts 29
Plastics Kit
contents 19
spare part numbers 16, 19,
25
pointing device
components 7
illustrated 7
pointing device components
TouchPad 7
TouchPad buttons 7
TouchPad scroll zone 7
pointing devices, product
description 5
ports
external monitor 11
monitor 11
product description 4
Universal Serial Bus (USB) 11
power button 8
power connector 11
power cord
set requirements 128
spare part numbers 22, 26
power light 9
power requirements, product
description 5
power-on password 84
processor
product description 1
removal 66
spare part numbers 17, 27,
28, 66
product description
audio 4
chipset 1
diskette drive 3
Ethernet 4
external media cards 4
graphics 2
hard drives 3
keyboard 5
memory module 2
modem module 4
operating system 5
optical drives 3
panels 2
pointing devices 5
ports 4
power requirements 5
processors 1
product name 1
security 5
serviceability 6
wireless 4
product name 1
R
recovering information 119, 123
recovery partition 120
removal/replacement
preliminaries 29
procedures 35
restoring the hard drive 120
right-side components 10
RJ-11 jack
location 11
pin assignments 126
RJ-11 jack cable
release 67
spare part numbers 20
RJ-45 jack
location 11
pin assignments 127
RTC battery
removal 34
spare part numbers 17, 24,
34
Rubber Kit, spare part
numbers 27
S
Screw Kit
contents 98
spare part numbers 23, 27
screw listing 98
SD Card Reader 10
security cable slot 10
Security menu 84
security, product description 5
serial number 14, 35
service considerations 29
serviceability, product
description 6
setup utility
accessing 81
Diagnostics menu 84
File menu 83
Security menu 84
System Configuration
menu 85
speaker
location 9
removal 51
spare part numbers 16, 25,
51
specifications
computer 88
display 89
DVD/CD-RW Combo Drive 92
DVD±RW and CD-RW Combo
Drive 91
hard drive 90
I/O addresses 95
interrupts 94
memory map 97
optical drive 91, 92
system DMA 93
startup check 84
static-shielding materials 33
stringent security 84
switch cover
removal 47
spare part numbers 16, 27,
47
system board
removal 66
spare part numbers 16, 26,
28, 66
System Configuration menu 85
system DMA 93
system fan 86
system information 83
system memory map 97
T
thermal material,
replacement 72, 73
tools required 29
top components 7
top cover
removal 58
spare part numbers 16, 27,
58
TouchPad
spare part numbers 16, 27
TouchPad board
removal 61
spare part numbers 61
TouchPad button board
removal 61
spare part numbers 16, 27,
61
TouchPad buttons 7
TouchPad components 7
TouchPad scroll zone 7
transporting guidelines 32
Windows recovery 123
Windows Vista operating system
DVD 121
wireless antenna,
disconnecting 42
wireless antennae 13
wireless button 8
wireless light 8
wireless, product description 4
WLAN module
removal 40
spare part numbers 18, 40
WLAN module compartment 12
WLAN module compartment cover
illustrated 19
removal 42
workstation guidelines 32
U
unknown password 34
USB legacy support 81, 85
USB port
location 11
pin assignments 127
V
vents 11, 12
W
Windows applications key 9
Windows Backup utility 122, 123
Windows logo key 9
Index 139
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising