Full Product Manual
Use and Care Guide
Item #1001-549-998
Model #31044
UPC # 00030878310444
In-Wall Easy Set Digital Timer
Before You Begin
Safety Information
Product Description
RISK OF ELECTRIC SHOCK:
…… Shut off the power at the fuse box or circuit breaker before installation.
…… Do not use in wet locations.
…… Use indoors only.
WARNING
1
RISK OF ELECTRIC FIRE:
…… Do not use to control appliances that contain heating elements such as cooking
appliances, heaters, and irons.
…… Do not exceed electrical ratings.
…… Use only copper wire with this device.
…… Do not use to control receptacles.
Product Specifications
program
2
3
4
6
5
8
9
7
Part
Description
RATINGS
1
Timer
120VAC, 60 Hz
2
LCD display
1200W Tungsten
3
Down arrow button – Used to scroll through timer settings
1200VA Ballast
4
Reset button – Used to reset the timer to factory default settings
15A Resistive
5
Up arrow button – Used to scroll through timer settings
1/2 HP
6
On button – Used to manually turn the light on
7
Off button – Used to manually turn the light off
8
My On Time buttons – Used to create a custom ON time for your timer. Factory default
settings are 5:00 pm and 5:00 am.
9
My Off Time buttons – Used to create a custom OFF time for your timer. Factory default
settings are 12:00 am and 8:00 am.
Hardware Included
AA - Screw x2
BB - Jumper Cable x1
Installation
□□
□□
□□
□□
□□
□□
□□
NOTE: Be sure that all wires and wire nuts are secure.
Line
Load
Turn power off at circuit breaker or fuse box before installation.
Remove the current wallplate and switch from the wall box.
Remove the timer from the packaging and locate the LINE, LOAD, NEUTRAL and GROUND terminals on the back of the timer.
Loosen the LINE, LOAD, NEUTRAL, and GROUND screws with either a flat-blade or Phillips screwdriver. When loosening screws,
stop when you feel resistance.
Strip the wires to 5/8 in. (16 mm).
Insert the line side wire from the wire box into the hole marked LINE and tighten the LINE screw.
Insert the load side wire from the wire box into the hole marked LOAD and tighten the LOAD screw.
Insert the ground wire from the wire box into the hole marked GROUND and tighten the GROUND screw.
Remove the white jumper wire (BB) from the package. Insert and tighten the jumper wire into the hole marked NEUTRAL.
Connect the neutral jumper wire (BB) from the timer to the neutral wire in the wire box. Often the neutral wire (white) can be found
in the back of the wire box connected with a wire nut. There may be several neutral wires bound together. Add the neutral jumper
wire (BB) to all neutral wires bound together and retighten the wire nut, making sure that the wire nut is tight.
Tug each wire to verify connection, retighten if needed.
Load
Neutral
□□
□□
□□
□□
INITIAL SETUP
NOTE: If you are unsure or unclear about this installation or if the wires in your box do not match the manual
(not all switch boxes have neutral wires), contact a qualified licensed electrician.
Neutral
Line
1
Ground
Ground
= Wiring Nut
Black
Green
Ground
LOAD
120 VAC
Power
Source
Black
Light
LINE
White
White
□□ Insert the timer into the wall box, being careful not to pinch any wires. Be sure the TOP (indicated on yoke of timer) is facing up.
Fasten the timer to the wall box using the screws (AA).
□□ Place the rocker/decorator wallplate on the timer, being careful to not overtighten wallplate screws.
□□ Turn the power on at the circuit breaker or fuse box.
Operation
1
INITIAL SETUP – SETTING THE TIME
□□ Press the Reset button (4) using a toothpick or pencil.
□□ Use the Up (5) and Down (3) arrows to set the curernt time, taking note of the AM and PM on the display (2).
program
3
4
2
5
NOTE: Press and hold the Up (5) or Down (3) arrows to cycle through the time faster.
2
CHOOSING A CUSTOM ON/OFF TIME
□□ Press the My On Time button (8) and then use the Up (5) and Down (3) arrow buttons to set the time you want the timer to turn On.
The blue light next to My On Time (8) should turn on, indicating that the On time is set and activated.
NOTE: Press and hold the Up (5) or Down (3) arrows to cycle through the time faster.
program
3
5
8
9
□□ Press the My Off Time button (9) and then use the Up (5) and Down (3) arrow buttons to set the time you want the timer to turn Off.
The blue light next to My Off Time (9) should turn on, indicating that the Off time is set and activated.
□□ To set a second set of on and off times, repeat this procedure using the second set of My On Time (8) and My Off Time (9) buttons.
NOTE: If you set the My On Time earlier than the current time, the timer does not turn on until the next day at the time scheduled. Use the manual
override feature to turn on the timer if needed immediately.
3
USING THE MANUAL OVERRIDE FEATURE
□□ Press the On (6) and Off (7) buttons at any time to manually turn lights on and off. The timer will follow the next scheduled ON and
OFF times.
4
program
6
7
DAYLIGHT SAVINGS TIME
□□ When daylight savings time occurs, use the Up (5) and Down (3) arrow buttons to adjust the clock time by 1 hour.
FCC NOTE
This device complies with part 15 of the FCC and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This Class B digital apparatus complies with Canadian ICES-003. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
IP07232014HOMEDEPOT.com
Please contact 1-866-308-3976 for further assistance.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising