IDEA MOVING LED 100
1 . 0 1
R E L .
I D E A M OV I N G
LED 100
M O V I N G
GB
A N U A L
I
D
F
E
U S E R ’ S
M
P
H E A D
SGM
IT
PULIZIA E MANUTENZIONE
I seguenti punti devono essere tenuti in considerazione durante l’ispezione:
1. Tutte le viti per installare l’apparecchio o parti dell’apparecchio devono essere strette saldamente e
non devono essere corrose.
2. Non ci deve essere nessuna deformazione sul corpo, sulle lenti a colori, sui punti di fissaggio e di
installazione (soffitto, sospensione, trussing).
3. Parti meccaniche in movimento non devono mostrare tracce di usura e non devono ruotare in modo
sbilanciato.
4. I cavi di alimentazione non devono mostrare segni di danni, di usura del materiale o sedimenti
Ulteriori istruzioni basate sul punto di installazione e d’utilizzo devono essere eseguite da un installatore
esperto ed ogni problema relativo alla sicurezza deve essere eliminato.
ATTENZIONE!
Scollegare dall’alimentazione prima di iniziare lavori di manutenzione.
Per mantenere le luci in buone condizioni ed estendere il tempo di vita, raccomandiamo una pulizia regolare
delle luci.
1. Pulire le lenti dentro e fuori ogni settimana per evitare la debolezza delle luci dovuta ad accumulo di
polvere
2. Pulire la ventola ogni settimana
3. Un controllo elettrico dettagliato da un ingeniere elettrico approvato ogni tre mesi, assicurarsi che i
contatti del circuito siano in buone condizioni, prevenire il cattivo contatto del circuito da
surriscaldamento.
Raccomandiamo una pulizia frequente dell’apparecchio. Per piacere usare un panno morbido umido e senza
peli. Non usare mai alcool o solventi!
Non ci sono parti utilizzabili nell’apparecchio eccetto la lampada. Per piacere fare riferimento alle istruzioni
sotto la voce “Istruzioni per l’installazione”. Se si dovesse aver bisogno di pezzi di ricambio, per piacere
ordinare parti originali dal proprio rivenditore locale.
CARATTERISTICHE TECNICHE
Alimentazione: 100V~240V AC,50 Hz /60Hz
Consumo d’energia: max. 230W
Dimensioni dell’imballo: 35x29.5x43cm
Peso netto: 7.6KG
Peso lordo: 10KG
Nota: sono esclusi errori ed omissioni per ogni informazione data in questo manuale. Ogni informazione è
soggetta a modifica senza preavviso.
Idea Moving Led 100
18
XM335-V1.1-A
Vi ringraziamo per aver acquistato un prodotto SGM.
Per ottenere i migliori risultati dal suo utilizzo, vi preghiamo di leggere attentamente questo manuale di istruzioni.
Al suo interno troverete le informazioni tecniche e le specifiche d’uso del prodotto. Nelle pagine in appendice troverete inoltre schemi e diagrammi destinati all’assistenza tecnica.
Nell’ottica di qualità SGM, è possibile che l’Azienda apporti migliorie ai suoi prodotti, per cui consigliamo di allegare il manuale al prodotto stesso e di trascrivere il numero di serie nell’ultima pagina della copertina: utilizzando
il presente manuale con un apparecchio fabbricato prima o dopo la sua stampa, potrebbero esserci discrepanze
fra l’apparecchio e quanto riportato nel manuale stesso.
Thank you for buying an SGM product.
To obtain the best results, please carefully read this instruction manual in which you will find technical information
and specifications for use of the product, as well as diagrams for technical service in the appendix.
In light of SGM quality, the company may make improvements to its products. Therefore, we recommend that the
manual be attached to the product and the serial number copied onto the back cover: using this manual with
equipment manufactured before or after its printing, might show discrepancies between the equipment and the
information listed in the manual.
Wir danken Ihnen für den Kauf eines Produkts von SGM.
Zur Erzielung der besten Resultate bei der Benutzung bitten wir Sie, die vorliegende Bedienungsanleitung aufmerksam zu lesen. Darin finden Sie die technischen Informationen sowie die Anweisungen für die Benutzung des
Produkts. Im Anhang befinden sich auBerdem die Schaltpläne undv Diagramme für den Kundendienst.
SGM behält sich das Recht vor, Verbesserungen an den Produkten vorzunehmen und deshalb empfehlen wir, die
Bedienungsanleitung dem Produkt stets beizulegen und die Seriennummer auf der letzten Seite des Umschlags
einzutragen. Bei der Verwendung dieses Handbuches mit einem Gerät, das vor oder nach der Drucklegung produziert wurde, können sich Abweichungen zwischen Gerät und dem Inhalt des Handbuches ergeben.
Nous vous remercions d’avoir acheté un produit SGM.
Pour optimiser son utilisation, nous vous prions de bien vouloir lire attentivement cette notice où vous trouverez
les informations techniques et les caractéristiques d’utilisation du produit. En outre, vous trouverez également,
dans les pages en appendice, les schémas et les diagrammes concernant l’assistance technique.
Le concept de qualité SGM, lui permet d’améliorer continuellement ses produits et c’est pourquoi nous vous conseillons de joindre la notice au produit et d’inscrire le numéro de sèrie sur la page de couverture. En effet, si on
l’utilise avec un appareil fabriqué avant ou après son impression, il peut y avoir des différences entre l’appareil et
ce qui figure dans la notice.
Les estamos sumamente agradecidos por haber elegido un producto SGM.
Para obtener los mejores resultados, les rogamos leer detenidamente el presente manual de instrucciones. El
mismo contiene las informaciones técnicas y las indicaciones de uso del producto. Las páginas anexas contienen
además los esquemas y diagramas necesarios para la asistencia técnica.
Para mantener la calidad SGM, es posible que la Empresa aporte mejoras sus productos, por ello les aconsejamos
conservar el manual junto con el aparato correspondiente y escribir su número de serie en la última página del
manual; si en cambio se utiliza el presente manual con un aparato frabicado antes o después de su impresión, es
probable que existan discrepancias entre el aparato y las indicaciones del mismo.
GB
SGM
Table of Contents
INTRODUCTION: .............................................................................................................................................2
Features..................................................................................................................................................2
OVERVIEW......................................................................................................................................................3
SAFETY INSTRUCTIONS ...................................................................................................................................4
GENERAL GUIDELINES .....................................................................................................................................5
INSTALLATION INSTRUCTIONS .........................................................................................................................5
Mounting the device .................................................................................................................................5
Installation method via clamp ....................................................................................................................6
DMX-512 control connection ......................................................................................................................6
Control Board ..........................................................................................................................................9
FUNCTION MODE...........................................................................................................................................10
DMX address setting ...............................................................................................................................10
Slave setting .........................................................................................................................................10
Auto Program ........................................................................................................................................10
Music control .........................................................................................................................................10
INFORMATION...............................................................................................................................................11
Time information....................................................................................................................................11
Software version ....................................................................................................................................11
PERSONALITY ...............................................................................................................................................11
Status Settings ......................................................................................................................................11
SERVICE SETTING .........................................................................................................................................12
Fans Control ..........................................................................................................................................12
Display Setting ......................................................................................................................................12
Temperature C/F ....................................................................................................................................12
Initial effect...........................................................................................................................................12
Wireless DMX.........................................................................................................................................12
RESET-FUNCTIONS ........................................................................................................................................13
EFFECT ADJUST.............................................................................................................................................13
Test function of each channel...................................................................................................................13
Lamp adjustment ...................................................................................................................................13
Calibrate values .....................................................................................................................................13
USERS MODE SET..........................................................................................................................................13
User mode ............................................................................................................................................13
Preset User mode...................................................................................................................................13
EDIT PROGRAM .............................................................................................................................................13
Select program ......................................................................................................................................13
Edit program .........................................................................................................................................13
Edit scenes............................................................................................................................................13
Auto scenes rec. ....................................................................................................................................13
INSTRUCTIONS ON USE .................................................................................................................................16
ERROR MESSAGE ..........................................................................................................................................17
CLEANING AND MAINTENANCE .......................................................................................................................18
TECHNICAL SPECIFICATIONS..........................................................................................................................18
XM335-V1.1-A
1
Idea Moving Led 100
GB
SGM
KEEP THIS MANUAL FOR FUTURE NEEDS
For your own safety, please read this user manual carefully before installing the device.
CAUTION !
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing
Every person involved with the installation, operation and maintenance of this device has to:
be qualified
follow carefully the instructions of this manual
INTRODUCTION:
Thank you for having chosen this professional moving head.
You will see you have acquired a powerful and versatile device.
Unpack the device. Inside the box you should find: the fixture device, an XLR connection cable, one omega
clamps and a safety rope and this manual. Please check carefully that there is no damage caused by
transportation. Should there be any, consult your dealer and don’t install this device.
Features
60pcs LEDS: 22x3W red, 17x3W green, 15x3W blue, 6x3W white
Extremely Long Life:50,000 Hr and low power consumption
DMX channel:13 channels
Pan/tilt movement: - 8 bit and 16 bit resolution
- For smooth and precise resolution
- Pan: 540°/630° optional, Tilt: 265°movement
- High speed of pan/tilt movement, speed of pan/tilt movement is
adjustable
- Scan position memory, auto reposition after unexpected movement
Strobe effect with 18 flashes per second and pulse effect
General dimming and blackout for all four colors
Excellent color mixing and rainbow effect
Friendly blue LCD display
Preset program: 7 built in programs can be called up via DMX controller
Idea Moving Led 100
2
XM335-V1.1-A
GB
SGM
OVERVIEW
1
2
1. Lens
2. Yoke
3
3. Base
4
4. Wireless DMX antenna
5. LCD-Display
6. Mode/esc-button
7. Up-button
8. Down-button
5 6 7 8 9 10
9. Enter-button
11
10. Microphone
11. Housing
12. 3-PIN DMX output socket
13. 3-PIN DMX input socket
14. 5-PIN DMX output socket
15. 5-PIN DMX input socket
16. Power switch
17. Fuse
18. Power supply
12 13 16 17 18 14 15
XM335-V1.1-A
3
Idea Moving Led 100
GB
SGM
SAFETY INSTRUCTIONS
CAUTION
Be careful with your operations. With a dangerous voltage you can Suffer a
dangerous electric shock when touching wires!
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe
operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written
in this user manual.
IMPORTANT
Damages caused by the disgregard of this user manual are not subject to warrenty.
The dealer will not accept liability for any resulting defects or problems.
If the device has been exposed to temperature changes due to environmental changes, do not switch it on
immediately. The arising condensation could damage the device. Leave the device switched off until it has
reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,
replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power
cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily
mean that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for smooth
air flow, so there should be no shelter for fans and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the
manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
CAUTION
Never touch device during operation!
The housing may heat up.
Never look directly into the light source,
as sensitive persons may suffer an epileptic shock.
Please be aware that damages caused by manual modifications to the device are not subject to warranty.
Keep away from children and non-professionals.
Idea Moving Led 100
4
XM335-V1.1-A
GB
SGM
GENERAL GUIDELINES
This device is a lighting effect for professional use on stages, in discotheques, theatres, etc.
This fixture is only allowed to be operated with the max alternating current which stated in the technical
specifications in the last page of this manual, the device was designed for indoor use only.
Lighting effects are not designed for permanent operation. Consistent operational breaks may ensure that
the device will fanction properly for a long time.
Do not shake the device.Avoid brute force when installing or operating the device.
The device shall only be used complete with its protective shield.
While choosing the installation-spot, please make sure that the device is not exposed to extreme heat,
moisture or dust. The minimum distance between light-output from the projector and the illuminated
surface must be more than 0.5 meter.
Always fix the fixture with an appropriate safety cable if you use the quick lock cam in hanging up the fixture,
please make sure the 2 quick lock fasteners turned in the quick lock holes correctly.
If you use the quick lock cam in hanging up the fixture, please make sure the 2 quick lock fasteners turned
in the quick lock holes correctly.
Operate the device only after having familiarized with its functions. Do not permit operation by persons not
qualified for operating the device. Most damages are the result of unprofessional operation.
Please use the original packaging if the device is to be transported.
For safety reasons, please be aware that all modifications on the device are forbidden.
If this device will be operated in any way different to the one described in this manual, the product may
suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to
short-circuit, burns, electric shock, lamp explosion, crash, etc.
INSTALLATION INSTRUCTIONS
Mounting the device
CAUTION
Pleas consider the EN 60598-2-17 and the other respective national norms
during the installation. The installation must only be carried out by a
qualified person.
The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for
1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate safety
rope.
Never stand directly below the device when mounting, removing or servicing the fixture.
The operator has to make sure the safety relating and machine technical installations are approved by an
expert before taking the device into operation for the first time.
These installations have to be approved by a skilled person once a year.
Cautions:
The effect should be installed outside areas where persons may reach it, walk by or be seated.
Overhead mounting requires extensive experience, including amongst others calculating working load limits,
installation material being used, and periodic safety inspection of all installation material and the device. If
you lack these qualifications, do not attempt the installation yourself. Improper installation can result in
bodily injury.
CAUTION
The electric connection must only be carried out by a qualified electrician.
XM335-V1.1-A
5
Idea Moving Led 100
GB
SGM
Before mounting make sure that the installation area can hold a minimum point load of 10 times the device’s
weight.
Connect the fixture to the mains with the power plug.
Installation method via clamp
Please refer to the picture below:
Screw one clamp each via a M12 screw and nut onto the Omega holders.
Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of the
device. Tighten the quick-lock fasteners fully clockwise. Install the second Omega holder.
Pull the safety-rope through the holes on the bottom of the base and over the trussing system or a safe
fixation spot. Insert the end in the carabine and tighten the safety screw.
DMX-512 control connection
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the
male 3-pin XLR input of the moving head. You can chain multiple
Moving head together through serial linking. The cable needed should be two core, screened cable with XLR
input and output connectors. Please refer to the diagram below.
Idea Moving Led 100
6
XM335-V1.1-A
GB
SGM
Address 27
Address14
Address 1
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment,
such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of
the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor
connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture in the
chain. Please see illustrations below.
120Ω
2
3
1
PIN 3
PIN 2
Projector DMX starting address selection
All fixtures should be given a DMX starting address when using a DMX signal, so that the correct fixture
responds to the correct control signals. This digital starting address is the channel number from which the
fixture starts to “listen” to the digital control information sent out from the DMX controller. The allocation of
this starting address is achieved by setting the correct number on the display located on the base of the
device.
You can set the same starting address for all fixtures or a group of fixtures, or make different address for
each fixture individually.
If you set the same address, all the units will start to “listen” to the same control signal from the same
channel number. In other words, changing the settings of one channel will affect all the fixtures
simultaneously.
If you set a different address, each unit will start to “listen” to the channel number you have set, based on
the quantity of control channels of the unit. That means changing the settings of one channel will affect only
the selected fixture.
In the case of the moving head, which is 13 channels fixture when you select the standard channel mode,
you should set the starting address of the first unit to 1, the second unit to 14(13 + 1), the third unit to 27
(13+ 14), and so on.
XM335-V1.1-A
7
Idea Moving Led 100
GB
SGM
Operting instructions of the internal DMX wireless system
1. Equipments:
DMX 512 controller, wireless transmitter, and the fixtures with wireless receiver.
2. Message from the LED indicator:
1. Rapid flashing red/Green: logging in to a transmitter
2. Slow flashing Red/Green: Logged on a transmitter and the DMX line is idle (No DMX is connected to
transmitter).
3. Solid Green: Logged on to a transmitter and receiving DMX data.
4. Solid Red: Not logged on to a transmitter (free)
3. WDMX in the menu of the fixture:
On a fixture installed with wireless system, in order to switch between wireless control system and
traditional DMX control (with cable), a new menu WDMX is added to the display board.
ON: (Activate WDMX)
1. When the fixture is on power,and the WDMX is activated to ON status, but did not connect to the
controller and did not log in to the transmitter, the fixture will search for the DMX signal source. If the
fixture is connected to the DMX controller it can be controlled by DMX controller; if it is log in to the
wireless transmitter, it can be controlled by the Transmitter
2. When the fixture is power off, and the WDMX is in ON status, if the fixture is connected to DMX
controller. After the fixture is power on, it can be controlled only by the DMX controller which
connected. The fixture can log in the wireless transmitter, and receive only radio signal from
transmitter, but not DMX from the transmitter.
OFF: (De-activate WDMX)
In this status, wireless system is not activated, so the fixture can not log in the transmitter.
REST: (reset WDMX memory);
Can remove the fixture from the connection with the transmitter, the fixture become free and ready
to log in any transmitter.
4. Setup the wireless system:
1. Connect the transmitter with the DMX controller
2. To make the fixture installed with wireless receiver log in to the transmitter
a) Initially, the indicator on the receiver fixture should be in Solid red
b) Press and hold the configuration button on transmitter for less than 3 seconds the red/green
LEDs on the transmitter and the receiver fixture will flash rapidly for about 5~ 10 seconds while
the system goes through its setup procedure.
c) Once the receiver fixture is logged in to the transmitter (T1), the fixture with wireless receiver
will keep the memory, even if restart the power, this unit will log in the transmitter (T1)
automatically.
3. Use the DMX 512 to control the fixture
5. Remove the receivers from transmitter (T1) and to log in to another transmitter (T2)
Case 1: Remove a receiver:
a) On the control board of the fixture, enter menu to activated the function of REST;
b) The LED for wireless on the fixture should turn to Solid red; the receiver can log out from the
transmitter (T1);
c)
press the configuration button on transmitter(T2) for less than 3 second, then the fixture will start to
connect with the transmitter(T2)
Case 2: Remove all receivers from a transmitter (T1) to log in to T2;
Press and hold the configuration button on the T1 as least 5 seconds, can clear the connection with
all the fixtures.
All the red/green LEDs on the receiver fixtures will turn to Solid red to indicate that the receivers are
unassigned and removed from the transmitter ( T1);
Press and hold the configuration button on the T2 less then less than 3 second , the fixtures will
connect with the T2
PS:
1. Please log the receivers out from the transmitter after every job, so that the receivers are in free un
assigned state and ready to be assigned to a transmitter.
2. Do not connect the fixture which is under the communication of wireless system to the DMX controller,
otherwise it will cause interference from the DMX controller.
Idea Moving Led 100
8
XM335-V1.1-A
GB
SGM
Control Board
The Control Board offers several features: you can simply set the starting address, switch on and off the
lamp, run the pre-programmed program or make a reset.
The main menu is accessed by pressing the Mode/esc-button until the display starts flashing. Browse
through the menu by pressing the Up-button or Down-button. Press the Enter-button in order to select the
desired menu. You can change the selection by pressing the Up-button or Down-button. Confirm every
selection by pressing the Enter-button. You can leave every mode by pressing the Mode/esc-button. The
functions provided are described in the following sections.
To access display Menu via the internal battery, press the UP & DOWN buttons simultaneously.
Display will automatically switch off after about 10 seconds from last button press.
Function Mode
Default settings shaded
Set Dmx Address
Value Display
Set To Slave
Auto Program
Music Control
Time Information
A001~AXXX
PAN……
Slave1,Slave2,Slave3
Master / Alone
Master / Alone
XXXX(Hours)
Power on running time
Total Life Hours
XXXX(Hours)
Fixture running time
Last Run Hours
XXXX(Hours)
Fixture Last times clear
Timer Password
Password=XXX
Timer Password
Temperature Info
Clear Last Run
Head Temperature
ON/OFF
XXX℃/℃
Clear Fixture Last time
Temperature in the head
Software Version
Status Settings
Ver1.0
Address via DMX
ON/OFF
No DMX Status
Close/Hold/Auto/Music
Software version of each IC
Add. via DMX
Auto run if no DMX
Pan Reverse
ON/OFF
Pan Reverse movement
Tilt Reverse
ON/OFF
Tilt Reverse movement
Fine Resolution
ON/OFF
Fine resolution switch
Pan Degree
630/540
Pan Degree Select
Feedback
ON/OFF
Speed 1~ 4
0~99%
Movement Feedback switch
Password=XXX
High/Low
Service Code“=050”
Fan Voltage Select
Information
Current Time
Movement Speed
Personality
Mic Sensitivity
Service Setting
Fans Control
Display Setting
Temperature C/F
Reset
Function
DMX address setting
DMX value display
Slave setting
Auto program
Music control
Service Password
Fan Voltage
Auto Fans Speed
High Fans Speed
Low Fans Speed
Shutoff Time
Movement Mode Select
Sensitivity of Mic.
Fans Speed Mode Select
Display shutoff time
Temperature switch between
℃/℃
Initial effect position
Initial Effect
Celsius
Fahrenheit
PAN……
Wireless DMX
De-Act WDMX
De-activate WDMX
Activate WDMX
Activate WDMX
Act & Data Out
Act & Data Out
Reset Wireless DMX Mem
Reset Default
Reset All
Reset Pan&Tilt
XM335-V1.1-A
PAN =XXX
Rest WDMX Mem
ON/OFF
Restore factory sett.
Reset all motors
Reset Pan/Tilt
9
Idea Moving Led 100
GB
Users Mode Set
Effect Adjust
SGM
Test Channel
Manual Control
Calibrate Values
User Mode
Edit User Mode
Edit Program
Select Programs
Edit Program
Edit Scenes
Rec. Controller
PAN ……
PAN
Test function
Fine adjustment of the lamp
PAN =XXX
:
--Password-PAN
:
XXXXXX(Band)
User Mode A
User Mode B
User Mode C
:
Password=XXX
PAN=XXX
:
Calbrate and adjust the
effects
to
standard/right
position Password “050”
User’s mode to change
channel numbers
PAN
:
Auto Pro Part 1
Auto Pro Part 2
Auto Pro Part 3
PAN = CH01
:
Program 1 ~ 10 Program 1
Program 1 ~ 10 Program 2
Program 1 ~ 10 Program 3
Select programs to be run
Program 1
:
Program 10
Edit Scene 001
~ Edit Scene
250
Program Test
Step 01=SCxxx
Step 64=SCxxx
Pan,Tilt,……
--Secne Time-Input By Outside
Testing program
Program in loop
Save and exit
Save and automatically
return
manual scenes edit
(“STEP
XX”)
Pan=xxx…
…
TIME=xx.x
s
XX~XX
Preset User modes
Automat. scenes rec
FUNCTION MODE
DMX address setting
With this function, you can adjust the desired DMX-address via the Control Board.
Select “Set DMX address” via the encoder.
Press the encoder, adjust the DMX address by turning the encoder.
Press the encoder to confirm.
Press the Mode/Esc-button in order return to the main menu.
Display the DMX 512 value of each channel
With this function you can display the DMX 512 value of each channel. The display automatically shows the
channel with a value changing.
Slave setting
With this function, you can define the device as slave.
Auto Program
With this function, you can run the internal program. You can select the desired program under “Select
program”. You can set the number of steps under “Edit program”. You can edit the individual scenes
under “Edit scenes”. With this function, you can run the individual scenes either automatically, i.e. with the
adjusted Step-Time.
Music control
With this function, you can run the internal program sound-controlled.
Idea Moving Led 100
10
XM335-V1.1-A
GB
SGM
INFORMATION
Time information
Current Time
With this function, you can display the temporary running time of the device from the last power on. The
display shows “XXXX”, “XXXX” stands for the number of hours. The counter is resetted after turning the
device off.
Total life Hours
With this function, you can display the running time of the device. The display shows “XXXX”, “XXXX” stands
for the number of hours.
Last Run Hours
With this function, you can display last the running time of the lamp. The display shows “XXXX”, “XXXX”
stands for the number of hours.
Time Password
With this function, you can display the timer password. The time password is 038.
Clear Last Run
With this function, you can clear last run time of the fixture. The display shows “ON” or “OFF”, Press “Enter”
to confirm.
Temp. Info.
Head Temp
With this function you can display the temperature on the display board of the base (near CMY-filter) in
Celsius.
Software version
With this function, you can display the software version of the device.
Select “Software version” by turning the encoder.
Press the encoder, the display shows “V-X.X”, “X.X” stands for the version number, e.g. “V-1.0”,
“V-2.6”.
Turn the encoder in order to read the version of every individual IC.
Press the Mode/Esc-button in order to return to the main menu.
PERSONALITY
Status Settings
Address via DMX
With this function, you can adjust the desired DMX-address via an external controller.
Select “Address via DMX” by turning the encoder.
Press the encoder, the display shows “ON” or “OFF”.
Turn the encoder to select “ON” if you wish to enable this function or “OFF” if you don’t.
Press the encoder to confirm.
Press the Mode/Esc-button in order to return to the main menu.
On the controller, set the DMX-value of channel 1 to "7".
Set the DMX-value of channel 2 to "7"or "8". When set to "7" you can adjust the starting address between
1 and 255. When set to "8" you can adjust the starting address between 256 and 511.
Set the DMX-value of channel 3 to the desired starting address. If you want to set the starting address
to 57, set channel 1 to "7", channel 2 to "7" and channel 3 to "57". If you want to set the starting address
to 420,set channel 1 to "7", channel 2 to "8" and channel 3 to "164" (256+164=420).
Wait for approx. 20 seconds and the unit will carry out a reset. After that, the new starting address is set.
XM335-V1.1-A
11
Idea Moving Led 100
GB
SGM
No DMX Status
With this function, when the drive is not DMX signal, it runs automatism, close, hold and music, the default
is hold.
Pan Reverse
With this function you can reverse the Pan-movement.
Tilt Reverse
With this function you can reverse the Tilt-movement.
Fine resolution
With this function, you can fine resolution switch of pan movement or tilt movement.
Pan Degree
With this function, you can select pan degree for 630 or 540.
Feedback
With this function, you can feedback switch of pan movement or tilt movement.
Movement Speed
With this function, you can select scan mode from 1 to 4.
Mic Sensitivity
With this function, the default is 70%, you can select the desired microphone sensitivity from 0 % to 99 %.
SERVICE SETTING
Service Password
With this function, you can set the service password.
Fan Voltage
With this function, you can select fan voltage for high or low, the default is low
ATTENTION!!
The model is not recommended when ambient temperature is higher than
15 Celsius degree.
Fans Control
With this function, you can set the speed of the running fans. The selections have Auto、high and low.
Display Setting
Shut off time
With this function you can shut off the LCD display after 2 to 59 minutes. Turn the encoder in order to select
the desired shut off time.
Temperature C/F
With this function, Display the temperature for Celsius or Fahrenheit.
Initial effect
With this function, Display initial effect position.
Wireless DMX
From factory, this projector is prepared for wireless data transmission (W-DMX). If you wish to de-activate
W-DMX control, you can select the function “De-activate WDMX” by turning the encoder. With the function
“rest”, you can log out the projector from the wireless sender.
Reset Default
With this function, you can select restore factory set for ON or OFF, the default is OFF.
Idea Moving Led 100
12
XM335-V1.1-A
GB
SGM
RESET-FUNCTIONS
With this function you can reset the device via the Control Board. You can select the different reset functions
by turning the encoder.
EFFECT ADJUST
Test function of each channel
With this function you can test each channel on its (correct) function.
Lamp adjustment
With this function, you can adjust the lamp more easily. All effects will be canceled, the shutter opens and
the dimmer intensity will be set to 100 %. With the individual functions, you can focus the light on a flat
surface (wall) and erform the fine lamp adjustment.
Calibrate values
With this function, you can calibrate and adjust the effect wheels to their correct positions. The password
of calibrate values is 050.
USERS MODE SET
In this menu, user can select different channels list by different sequence:
For example, after the user enter this manual, if select Auto Program = CH 22, means in this User’s mode,
the “Dimmer” is in Channel 16.
User mode
With this function, you can create user defined channel orders.
Preset User mode
With this function, you can adjust the rest user defined channel order.
EDIT PROGRAM
Select program
With this function, you can select the program for the Program Run.
Edit program
With this function, you can edit the internal programs.
Edit scenes
With this function, you can edit the scenes of the internal programs.
Auto scenes rec.
The moving head features an integrated DMX-recorder by which you can transmit the programmed scenes
from your DMX-controller to the moving head. Adjust the desired scene numbers via the encoder (from – to).
When you call up the scenes at your controller, they will automatically be transmitted to the moving head.
Excursion:
A Master unit can send up to 3 different data groups to the Slave units, i.e. a Master unit can start 3 different
Slave units, which run 3 different programs. The Master unit sends the 3 program parts in a continuous loop.
The Slave unit receives data from the Master unit according to the group which the Slave unit was assigned
to. If e.g. a Slave unit is set to “Slave 1” in the menu “Set to Slave”, the Master unit sends “Auto Program
Part 1” to the Slave unit. If set to “Slave 2”, the Slave unit receives “Auto Program Part 2”.
XM335-V1.1-A
13
Idea Moving Led 100
GB
SGM
To start a Auto Program please proceed as follows:
1. Slave-Setting
Select “Function Mode” by turning the encoder.
Press the Enter button to confirm.
Select “Set to slave” by turning the encoder.
Press the Enter button to confirm.
Turn the encoder to select “Slave 1”, “Slave 2” or “Slave 3”.
Press the Enter button to confirm.
Press the Mode/Esc button in order to return to the main menu.
2. Automatic Program Run
Select “Function Mode” by turning the encoder.
Press the Enter button to confirm.
Select “Auto Program” by turning the encoder.
Press the Enter button to confirm.
Turn the encoder to select “Master” or “Alone”. The selection "Alone" means Stand Alone-mode and
"Master" that the device is defined as master.
Press the Enter button to confirm.
Press the Mode/Esc button in order to return to the main menu.
3. Program selection for Auto Pro Part
Select “Edit program” by turning the encoder.
Press the Enter button to confirm.
Select “Select programs” by turning the encoder.
Press the Enter button to confirm.
Turn the encoder to select “Auto Pro Part 1”, “Auto Pro Part 2” or “Auto Pro Part 3”, and thus select which
Slave program is to be sent. Selection “Part 1” means, that the Slave unit runs the same program as the
master units.
Press the Enter button to confirm.
Press the Mode/Esc button in order to return to the main menu.
4. Program selection for Edit Program
Select “Edit program” by turning the encoder.
Press the Enter button to confirm.
Select “Edit program” by turning the encoder.
Press the Enter button to confirm.
Turn the encoder to select the desired program. With this function you can edit specific scenes into a
specific program.
Press the Enter button to confirm.
Press the Mode/Esc button in order to return to the main menu.
5. Automatic Scene Recording
Select “Edit program” by turning the encoder.
Press the Enter button to confirm.
Select “Edit scenes” by turning the encoder.
Turn the encoder to select the desired scene numbers. You can program a maximum number of 250 •
Turn the encoder to select the desired scene numbers. You can program a maximum number of 250
scenes.
Press the Enter button to confirm.
Press the Mode/Esc button in order to return to the main menu.
Idea Moving Led 100
14
XM335-V1.1-A
GB
SGM
Example:
Program 2 includes scenes: 10, 11, 12, 13
Program 4 includes scenes: 8, 9, 10
Program 6 includes scenes: 12, 13, 14, 15, 16
Auto Pro Part 1 is Program 2;
Auto Pro Part 2 is Program 3;
Auto Pro Part 3 is Program 6
The 3 Slave groups run the Auto Program in certain time segments, as shown in the following picture:
XM335-V1.1-A
15
Idea Moving Led 100
GB
SGM
INSTRUCTIONS ON USE
DMX channel´s functions and their values (13 DMX channels):
Mode/Channel
St
Ba
1
1
Value
Ex
PAN Movement 8bit :
0-255
Pan Movement By 630/540
Pan Fine 16bit
2
3
Function
0-255
Fine control of Pan movement
TILT Movement 8bit :
3
0-255
Tilt Movement By 265
Tilt Fine 16bit
4
0-255
Fine control of Tilt movement
Speed Pan/Tilt movement:
5
6
5
0-225
226-235
blackout by movement
236-255
no function
Red LED
6
0-255
7
Red ( 0-Black , 255-100% Red )
0-255
:
Blue ( 0-Black , 255-100% Blue )
White LED
9
:
Green ( 0-Black , 255-100% Green )
Blue LED
8
0-255
9
:
Green LED
7
0-255
8
max to min speed
:
White ( 0-Black , 255-100% White )
Shutter, strobe:
10
10
11
11
12
12
0-31
Led trun off
32-63
Led turn on
64-95
Strobe effect slow to fast
96-127
Led turn on
128-159
Pulse-effect in sequences
160-191
Led turn on
192-223
Random strobe effect slow to fast
224-255
Led turn on
Dimmer intensity:
0-255
Intensity 0 to 100%
Rainbow:
0-7
No function
8-39
Rainbow colours
40-71
Rainbow colours
72-103
Rainbow colours
104-135
Rainbow colours
136-167
Rainbow colours
168-199
Rainbow colours
Idea Moving Led 100
16
XM335-V1.1-A
GB
SGM
200-231
232-255
Rainbow colours
Crossfading colours from slow to fast
Lamp on/off, reset, internal programs:
0-79
13
13
Normal
80-84
All motor reset
85-87
Scan motor reset
88-99
No function
100-119
Internal program 1 (secne1~8 of EEPROM)
120-139
Internal program 2 (secne9~16 of EEPROM)
140-159
Internal program 3 (secne17~24 of EEPROM)
160-179
Internal program 4 (secne25~32 of EEPROM)
180-199
Internal program 5 (secne33~40 of EEPROM)
200-219
Internal program 6 (secne41~48 of EEPROM)
220-239
Internal program 7 (secne49~56 of EEPROM)
240-255
Music Control (secne of Program 1)
ERROR MESSAGE
When you turn on the fixture, it will make a reset first. The display may show “XXer” while there are
problems with one or more channels. “XX” stands for channel 1, 2, 3,etc who has the testing sensor for
positioning.
For example, when the display shows “Red Er”, it means there is some error in channel 1. If there are some
errors on channel 1, channel 2, channel 5 at the same time, you may see the error message “Red Color Er”,
“Green Er ”, “Pan Er” flash repeated for 5 times, and then the fixture will generate a reset signal, all the
stepper reset. If the fixture remain error message after performing reset more than 3 times, it will detect
whether the fixture has more than 3 errors. If the fixture has more than 3 errors (including 3 errors), all the
channels can not work properly; but if the fixture has less than 3 errors, only the channels which have errors
can not work properly, others can work as usual.
PAN- movement Er
(PAN-yoke movement error) This message will appear after the reset of the fixture if the yoke’s
magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the stepping-motor is defective
(or its driving IC on the main PCB). The PAN- movement is not located in the default position after the reset.
TILT- movement Er
(TILT-head movement error) This message will appear after the reset of the fixture if the head’s
magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepping-motor is defective
(or its driving IC on the main PCB). The TILT- movement is not located in the default position after the reset.
XM335-V1.1-A
17
Idea Moving Led 100
GB
SGM
CLEANING AND MAINTENANCE
The following points have to be considered during the inspection:
1. All screws for installing the devices or parts of the device have to be tightly connected and must not be
corroded.
2. There must not be any deformations on the housing, color lenses, fixations and installation spots (ceiling,
suspension, trussing).
3. Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances.
4. The electric power supply cables must not show any damage, material fatigue or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer
and any safety problems have to be removed.
CAUTION
Disconnect from mains before starting maintenance operation.
In order to make the lights in good condition and extend the life time, we suggest a regular cleaning to the
lights.
1. Clean the inside and outside lens each week to avoid the weakneness of the lights due to accumulation
of dust.
2. Clean the fan each week.
3. A detailed electric check by approved electrical engineer each three month, make sure that the circuit
contacts are in good condition, prevent the poor contact of circuit from overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use alcohol or
solvents.
There are no serviceable parts inside the device except for the lamp. Please refer to the instructions under
“Installation instructions”.
Should you need any spare parts, please order genuine parts from your local dealer.
TECHNICAL SPECIFICATIONS
Power supply:
100V~240V,50Hz/60Hz
Power consumption:
max. 230W
Packing dimensions:
35x29.5x43cm
Net weight:
7.6KGS
Gross weight:
10KGS
Remark: errors and omissions for every information given in this manual excepted. All information is
subject to change without prior notice.
Idea Moving Led 100
18
XM335-V1.1-A
Vi ringraziamo per aver acquistato un prodotto SGM.
Per ottenere i migliori risultati dal suo utilizzo, vi preghiamo di leggere attentamente questo manuale di istruzioni.
Al suo interno troverete le informazioni tecniche e le specifiche d’uso del prodotto. Nelle pagine in appendice troverete inoltre schemi e diagrammi destinati all’assistenza tecnica.
Nell’ottica di qualità SGM, è possibile che l’Azienda apporti migliorie ai suoi prodotti, per cui consigliamo di allegare il manuale al prodotto stesso e di trascrivere il numero di serie nell’ultima pagina della copertina: utilizzando
il presente manuale con un apparecchio fabbricato prima o dopo la sua stampa, potrebbero esserci discrepanze
fra l’apparecchio e quanto riportato nel manuale stesso.
Thank you for buying an SGM product.
To obtain the best results, please carefully read this instruction manual in which you will find technical information
and specifications for use of the product, as well as diagrams for technical service in the appendix.
In light of SGM quality, the company may make improvements to its products. Therefore, we recommend that the
manual be attached to the product and the serial number copied onto the back cover: using this manual with
equipment manufactured before or after its printing, might show discrepancies between the equipment and the
information listed in the manual.
Wir danken Ihnen für den Kauf eines Produkts von SGM.
Zur Erzielung der besten Resultate bei der Benutzung bitten wir Sie, die vorliegende Bedienungsanleitung aufmerksam zu lesen. Darin finden Sie die technischen Informationen sowie die Anweisungen für die Benutzung des
Produkts. Im Anhang befinden sich auBerdem die Schaltpläne undv Diagramme für den Kundendienst.
SGM behält sich das Recht vor, Verbesserungen an den Produkten vorzunehmen und deshalb empfehlen wir, die
Bedienungsanleitung dem Produkt stets beizulegen und die Seriennummer auf der letzten Seite des Umschlags
einzutragen. Bei der Verwendung dieses Handbuches mit einem Gerät, das vor oder nach der Drucklegung produziert wurde, können sich Abweichungen zwischen Gerät und dem Inhalt des Handbuches ergeben.
Nous vous remercions d’avoir acheté un produit SGM.
Pour optimiser son utilisation, nous vous prions de bien vouloir lire attentivement cette notice où vous trouverez
les informations techniques et les caractéristiques d’utilisation du produit. En outre, vous trouverez également,
dans les pages en appendice, les schémas et les diagrammes concernant l’assistance technique.
Le concept de qualité SGM, lui permet d’améliorer continuellement ses produits et c’est pourquoi nous vous conseillons de joindre la notice au produit et d’inscrire le numéro de sèrie sur la page de couverture. En effet, si on
l’utilise avec un appareil fabriqué avant ou après son impression, il peut y avoir des différences entre l’appareil et
ce qui figure dans la notice.
Les estamos sumamente agradecidos por haber elegido un producto SGM.
Para obtener los mejores resultados, les rogamos leer detenidamente el presente manual de instrucciones. El
mismo contiene las informaciones técnicas y las indicaciones de uso del producto. Las páginas anexas contienen
además los esquemas y diagramas necesarios para la asistencia técnica.
Para mantener la calidad SGM, es posible que la Empresa aporte mejoras sus productos, por ello les aconsejamos
conservar el manual junto con el aparato correspondiente y escribir su número de serie en la última página del
manual; si en cambio se utiliza el presente manual con un aparato frabicado antes o después de su impresión, es
probable que existan discrepancias entre el aparato y las indicaciones del mismo.
U S E R ’ S
M
A N U A L
R E L .
1 . 0 1
MADE IN PRC - XM335
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising