Nokia X1-00 RM-732
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
SERVICE MANUAL
Level 1&2
Nokia X1-00
Nokia X1-01
RM-732 / RM-733
RM-713
Transceiver characteristics
Band
RM-732:
EGSM 900/1800
RM-733:
EGSM 850/1900
RM-713:
EGSM 900/1800
Display
128x160 TFT display
Operating System
S30 system Base 9
Connections:
3.5 mm AV connector, Stereo FM radio, MicroSD card
support up to 16GB
Transceiver with BL-5J battery pack
Talk time (GSM-A)
BL-5J 1320 mAh:
7 h (RM-732/RM-733)
7 h (RM-713)
BL-5J 1430 mAh:
7.5 h (RM-732/RM-733)
7.5 h (RM-713)
Standby (GSM-A)
BL-5J 1320 mAh:
1170 h (RM-732/RM-733)
785 h (RM-713)
BL-5J 1430 mAh:
1267 h (RM-732/RM-733)
850 h (RM-713)
Note:
Talk times are dependent on network parameters
and phone settings
1
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
Table of contents
1.
COPYRIGHT.......................................................................................................................................................................... 4
2.
WARNINGS AND CAUTIONS ............................................................................................................................................. 5
A. WARNINGS .......................................................................................................................................................................... 5
B. CAUTIONS ............................................................................................................................................................................ 5
3.
ESD PROTECTION ............................................................................................................................................................... 6
4.
CARE AND MAINTENANCE ................................................................................................................................................ 7
5.
BATTERY INFORMATION................................................................................................................................................... 8
6.
SINGLE SIM X1-00 VS DUAL SIM X1-01......................................................................................................................... 9
7.
EXPLODED VIEW ................................................................................................................................................................. 10
8.
SERVICE DEVICES ................................................................................................................................................................ 11
9.
SOFTWARE UPDATE........................................................................................................................................................... 12
10. DISASSEMBLY INSTRUCTIONS ......................................................................................................................................... 13
11. ASSEMBLY HINTS................................................................................................................................................................ 19
12. SOLDER COMPONENTS ...................................................................................................................................................... 20
2
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
CHANGE HISTORY
Status
Approved
Version No.
1.0
2.0
Date
08.03.2011
13.05.2011
Comments
First approved version
Exploded view and picture
story updated
Added RM-713
information in the first
page
Added disclaimer about
the differences between
Nokia X1-00 and Nokia X101
The purpose of this document is to help NOKIA service levels 1 and 2 workshop technicians to
carry out service to NOKIA products. This Service Manual is to be used only by authorized NOKIA
service suppliers, and the content of it is confidential. Please note that NOKIA provides also other
guidance documents (e.g. Service Bulletins) for service suppliers, follow these regularly and
comply with the given instructions.
While every endeavor has been made to ensure the accuracy of this document, some errors may
exist. If you find any errors or if you have further suggestions, please notify NOKIA using the
address below:
Nokia Care Academy
service.manuals@nokia.com
Please keep in mind also that this documentation is continuously being updated and modified,
so watch always out for the newest version.
3
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
1. COPYRIGHT
Copyright © 2011 Nokia. All rights reserved.
Reproduction, transfer, distribution or storage of part or all of the contents in this document in
any form without the prior written permission of Nokia is prohibited.
Nokia, Nokia Connecting People, and Nokia X and Y are trademarks or registered trademarks of
Nokia Corporation. Other product and company names mentioned herein may be trademarks or
tradenames of their respective owners.
Nokia operates a policy of continuous development. Nokia reserves the right to make changes
and improvements to any of the products described in this document without prior notice.
Under no circumstances shall Nokia be responsible for any loss of data or income or any special,
incidental, consequential or indirect damages howsoever caused.
The contents of this document are provided “as is”. Except as required by applicable law, no
warranties of any kind, either express or implied, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose, are made in relation to the
accuracy, reliability or contents of this document. Nokia reserves the right to revise this
document or withdraw it at any time without prior notice.
The availability of particular products may vary by region.
IMPORTANT
This document is intended for use by qualified service personnel only.
4
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
2. WARNINGS AND CAUTIONS
Please refer to the phone’s user guide for instructions relating to operation, care and
maintenance including important safety information. Note also the following:
a. Warnings
1. CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES FITTED WITH ELECTRONIC ENGINE
MANAGEMENT SYSTEMS AND ANTI–SKID BRAKING SYSTEMS. UNDER CERTAIN FAULT CONDITIONS,
EMITTED RF ENERGY CAN AFFECT THEIR OPERATION. IF NECESSARY, CONSULT THE VEHICLE
DEALER/MANUFACTURER TO DETERMINE THE IMMUNITY OF VEHICLE ELECTRONIC SYSTEMS TO RF
ENERGY.
2. THE HANDPORTABLE TELEPHONE MUST NOT BE OPERATED IN AREAS LIKELY TO CONTAIN
POTENTIALLY EXPLOSIVE ATMOSPHERES, EG PETROL STATIONS (SERVICE STATIONS), BLASTING
AREAS ETC.
3. OPERATION OF ANY RADIO TRANSMITTING EQUIPMENT, INCLUDING CELLULAR TELEPHONES, MAY
INTERFERE WITH THE FUNCTIONALITY OF INADEQUATELY PROTECTED MEDICAL DEVICES. CONSULT
A PHYSICIAN OR THE MANUFACTURER OF THE MEDICAL DEVICE IF YOU HAVE ANY QUESTIONS.
OTHER ELECTRONIC EQUIPMENT MAY ALSO BE SUBJECT TO INTERFERENCE.
b. Cautions
1. Servicing and alignment must be undertaken by qualified personnel only.
2. Ensure all work is carried out at an anti–static workstation and that an anti–static wrist
strap is worn.
3. Use only approved components as specified in the parts list.
4. Ensure all components, modules screws and insulators are correctly re–fitted after servicing
and alignment.
5. Ensure all cables and wires are repositioned correctly
5
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
3. ESD PROTECTION
Nokia requires that service points have sufficient ESD protection (against static
electricity) when servicing the phone.
Any product of which the covers are removed must be handled with ESD
protection. The SIM card can be replaced without ESD protection if the product
is otherwise ready for use.
To replace the covers ESD protection must be applied.
All electronic parts of the product are susceptible to ESD. Resistors, too, can be
damaged by static electricity discharge.
All ESD sensitive parts must be packed in metallized protective bags during
shipping and handling outside any ESD Protected Area (EPA).
Every repair action involving opening the product or handling the product
components must be done under ESD protection.
ESD protected spare part packages MUST NOT be opened/closed out of an ESD
Protected Area.
For more information and local requirements about ESD protection and ESD
Protected Area, contact your local Nokia After Market Services representative.
6
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
4. CARE AND MAINTENANCE
This product is of superior design and craftsmanship and should be treated with care. The
suggestions below will help you to fulfil any warranty obligations and to enjoy this product for
many years.
•
Keep the phone and all its parts and accessories out of the reach of small
children.
•
Keep the phone dry. Precipitation, humidity and all types of liquids or
moisture can contain minerals that will corrode electronic circuits.
•
Do not use or store the phone in dusty, dirty areas. Its moving parts can be
damaged.
•
Do not store the phone in hot areas. High temperatures can shorten the life
of electronic devices, damage batteries, and warp or melt certain plastics.
•
Do not store the phone in cold areas. When it warms up (to its normal
temperature), moisture can form inside, which may damage electronic circuit
boards.
•
Do not drop, knock or shake the phone. Rough handling can break internal
circuit boards.
•
Do not use harsh chemicals, cleaning solvents, or strong detergents to clean
the phone.
•
Do not paint the phone. Paint can clog the moving parts and prevent proper
operation.
•
Use only the supplied or an approved replacement antenna. Unauthorised
antennas, modifications or attachments could damage the phone and may
violate regulations governing radio devices.
All of the above suggestions apply equally to the product, battery, charger or any accessory.
7
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
5. BATTERY INFORMATION
Note: A new battery’s full performance is achieved only after two or three complete charge and
discharge cycles! The battery can be charged and discharged hundreds of times but it will
eventually wear out.
When the operating time (talk-time and standby time) is noticeably shorter than normal, it is
time to buy a new battery. Use only batteries approved by the phone manufacturer and
recharge the battery only with the chargers approved by the manufacturer.
Unplug the charger when not in use. Do not leave the battery connected to a charger for longer
than a week, since overcharging may shorten its lifetime.
If left unused a fully charged battery will discharge itself over time Temperature extremes can
affect the ability of your battery to charge.
For good operation times with Ni-Cd/NiMh batteries, discharge the battery from time to time by
leaving the product switched on until it turns itself off (or by using the battery discharge facility
of any approved accessory available for the product).
Do not attempt to discharge the battery by any other means Use the battery only for its
intended purpose.
Never use any charger or battery which is damaged.
Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object
(coin, clip or pen) causes direct connection of the + and - terminals of the battery (metal strips
on the battery) for example when you carry a spare battery in your pocket or purse.
Shortcircuiting the terminals may damage the battery or the connecting object.
Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions,
will reduce the capacity and lifetime of the battery. Always try to keep the battery between 15°C
and 25°C (59°F and 77°F).
A phone with a hot or cold battery may temporarily not work, even when the battery is fully
charged. Batteries’ performance is particularly limited in temperatures well below freezing.
Do not dispose batteries in a fire! Dispose of batteries according to local regulations (e.g.
recycling).
Do not dispose as household waste.
8
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
6. SINGLE SIM X1-00 VS DUAL SIM X1-01
Main difference between Nokia X1-00 and Nokia X1-01 is the number of SIM card holders under
the battery. Please see picture above.
The device used for the exploded view, disassembly picture story and the assembly hints in this
document is the single SIM version Nokia X1-00. The part names and item numbers in the
exploded view are identical in both devices. Also the procedures and the part names in the
disassembly picture story and the assembly hints are exactly the same.
9
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
7. EXPLODED VIEW
KEYMAT
I0002
A-COVER
I0001
A1
ATO SWAP PACKAGE
(I0003 - I0007) A2, A3
SCREW TORX+
SIZE 4 M1.4x4.5
I0003
UI SHIELDING
I0005
LIGHT GUIDE
I0004
EARPIECE
I0006
EARPIECE ADHESIVE
I0007
A2
LIGHT SWAP PACKAGE
(I0008 - I0011)
DOME SHEET
I0009
DISPLAY
I0008
A3
LIGHT SWAP PWB
I0010
D-COVER ASSEMBLY
(I0012 - I0016)
IHF SPEAKER
I0014
AV JACK
I0013
SPEAKER GASKET
I0015
DC JACK
I0012
D-COVER
I0016
TYPE LABEL
L3
I0011
SCREW TORX+
SIZE 4 M1.4x5
I0017
BATTERY COVER
I0018
Ver. 1.0
10
Only available
as assembly
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Not reuseable
after removal
L3 Repair/swap
only in level 3
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
8. SERVICE DEVICES
BL-5J Battery
CA-101 Service Cable
AC-3 Travel Charger
Nokia Standard Toolkit (v2)
For more information, refer to the
Service Bulletin (SB-011) on Nokia
Online. Supplier or manufacturer
contacts for tool re-order can be
found in “Recommended service
equipment” document on Nokia
Online.
11
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
9. SOFTWARE UPDATE
Flash concept (Point of Sale)
Please check always for the latest version of flash software, which is available on Nokia Online.
12
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
10. DISASSEMBLY INSTRUCTIONS
1) Nokia X1-00 disassembly.
2) You must use the Nokia Standard Toolkit version
2. You will also need the DC plug and the AV plug.
3) Protect the A-COVER with the protective film.
4) Open the BATTERY COVER by using the release
notch.
5) Remove the BATTERY COVER.
6) Unscrew the two Torx+ size 4 screws. Do not use
them again. Discard them.
13
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
7) Open the MICROSD slot. If there is a card inserted
remove it.
8) Release the A-COVER from the D-COVER by sliding
the SRT-6 to direction shown.
9) Release the sides of the A-COVER by sliding the
SRT-6 to direction shown.
10) Remove the A-COVER.
11) Protect the other side of the A-COVER with the
protective film.
12) Release the shown clips with the SS-93.
14
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
13) Remove the KEYMAT.
14) Protect the DISPLAY with a protective film.
15) Unscrew the four Torx+ size 4 screws.
16) Use the SRT-6 to release the ENGINE BOARD.
17) Remove the ENGINE BOARD.
18) Release the two clips holding the UI SHIELDING
with the SS-93.
15
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
19) Remove the UI SHIELDING.
20) Use the SS-93 to release the EARPIECE from the UI
SHIELDING.
21) Remove the EARPIECE with the tweezers.
22) Release the two guiding pins holding the LIGHT
GUIDE with the SS-93.
23) Remove the LIGHT GUIDE.
24) Use the dental tool release the DOMESHEET. Be
careful not to injure yourself with the sharp end of
the dental tool!
16
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
25) Peel of the DOMESHEET.
26) Remove the DOMESHEET. Do not use it again.
Discard it.
27) Use the AV plug to lift the AV JACK from its socket. 28) Remove it with the tweezers.
29) Use the DC plug to lift the DC JACK from its socket.
17
30) Remove it with the tweezers.
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
31) Use the SS-93 to release the IHF SPEAKER.
32) Remove it with the tweezers.
33) The Nokia X1-00 disassembly is now complete.
-END OF DISASSEMBLY-
18
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
11. ASSEMBLY HINTS
1) Insert the IHF SPEAKER with the tweezers. Make
sure that the pins are correctly aligned.
2) Push the IHF SPEAKER down from the shown place
to activate the adhesive.
3) Place the EARPIECE to its place with the tweezers.
4) Push the EARPIECE down with the SS-93 to activate
the adhesive.
5) Tighten the TORX + size 4 screws to the torque of
17 Ncm.
6) Tighten the TORX + size 4 screws to the torque of
15 Ncm.
19
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Nokia X1-00 (RM-732 / RM-733)
Nokia X1-01 (RM-713)
Service Manual Level 1&2
12. SOLDER COMPONENTS
Not included
20
Conf idential | Copyright © 2011 Nokia | A ll rights reserved
Version 2.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising