Pro-Shift Lite
INSTALLATION INSTRUCTIONS
PRO-SHIFT LITE
®
Instr. No. 2650-397F
MODEL 5340 For Standard and Electronic Racing Ignitions,
5341 For Vertex OAC Ignitions,
5342 For vertex OXC and Super Mag. Ignitions
Features
Module Kits
• High accuracy-Custom RPM Modules (Pills).
Each kit includes 5 calibrated module "pills" in 200 RPM
increments beginning with the first number listed.
• Order separately in different RPM ranges with 5
modules per pack at 200 rpm intervals.
Example:
5357
7,000
5367
6,600
5353 3,000
5354 4,000
• Special amber lens assures you won't miss the lite. 5355 5,000
5356 6,000
• Easy change wedge-base bulb (G.E. #921 Bulb).
5357 7,000
• User choice of dash or tach mounting.
5358 8,000
5359 9,000
• Easy to select 4, 6, and 8 cylinder operation.
• Self-test feature flashes lamp when power is
Cylinder Select
(7.0, 7.2, 7.4, 7.6, 7.8 x 1000) or;
(6.6, 6.8, 7.0, 7.2, 7.4 x 1000)
5360 10,000
5361 11,000
5362 12,000
5363 13,000
5364 3,600
5365 4,600
5366 5,600
5367 6,600
5368 7,600
5369 8,600
5370 9,600
5371 10,600
5372 11,600
5373 12,600
Place switch in
desired cylinder
range.
NOTE: MAGNETO MODELS,
OPERATE IN THE 8 CYLINDER
RANGE ONLY. 4 AND 6
CYLINDER MODELS ARE NOT
AVAILABLE.
turned on.
Wiring
Standard Ignition
Model 5340
Red to Switched 12 Volt +
WARNING
Warranty will be void
if connected to coil
on MSDignitions.
Black to chassis or engine ground
OR
Green
to coil
Yellow
RPM
Module
Grommet
in Firewall
On standard
ignitions GREEN
wire attaches to
coil negative (-).
GREEN
On electronic
ignitions, such as
GM, HEI, or MSD,
connect wire to
tach terminal.
COIL
Electronic
Ignition Tach
Terminal
NOTE: THE 2 PINS ON THE
MODULES ARE PLACED LOWER
THAN CENTER. THE MODULE
MUST BE INSERTED WITH THE
NUMBERS READING
UPRIGHT.THIS APPLIES TO ALL
MODELS.
Center
Lower
Than
Center
Vertex OAC
Red to Switched 12 Volt +
Model 5341
Black to chassis or engine ground
MAGNETO
Yellow RPM
Module
Yellow to Vertex Primary
or high side of kill switch
Magneto Primary
Terminal
Super Mag and Vertex OXC
Red to Switched 12 Volt +
IMPORTANT
Inductive Tr i g g e r e d
instrument must use
its own pick-up. (Part
Number 5210)
Model 5342
Tip: For Super Mag applications
it is recommended that ground
straps be connected from the
magneto clamp to both cylinder
heads.
Red
Inductive
PickUp
SUPERMAG
GND
Black
Purple
Smooth Black
splice to Black
ground wire
GND
Yellow RPM
Module
For Vertex OXC, a
.second pass through
the inductive pick-up is
..required
Ribbed Black
with white stripe
splices to purple
Mounting
On Your Auto Meter T a c h o m e t e r
It is not necessary to remove
the base from the Pro-Shift
to accomplish proper
mounting. For tach
mounting, loosen the shock
strap, slip the base under the
inner strap and re-tighten the
strap assembly.
On top of Your Dash
On Dash use
screws to
fasten base
to dash.
When dash
mounting,
screws should
be driven in at
a 45° angle.
BACK VIEW
Initial Testing
LED Conversion Kit
1. Set cylinder select switch on back of light tube to 4 cylinder for
pre-race mode.
2. Insert an RPM module (low PRM test module as described below).
3. Turn power on. Lamp should turn on briefly. This will not happen
without a module inserted in product.
4. Start engine and free rev to the module RPM. Include with the
PRO SHIFT is a low RPM pill module for testing. Insert pill
module and rev engine to appropriate RPM. This will allow you
to check the light to be certain that it works and can also be
used at any time as a "Test Pill" to check out the system. Lamp
will turn on, and stay on, at and above the set RPM. In the 4
cylinder test mode, 8 cylinder cars will light at 1⁄2 the shift RPM
and 6 cylinder cars will light at 2⁄3 the shift RPM.
Your PRO SHIFT can be converted to LED's using model 5339
Conversion Kit. This kit changes your PRO SHIFT FROM an
incandescent bulb to a fast reacting set of 4 large super bright LED's.
Troubleshooting
1.
2.
3.
4.
5.
Do you have 12 volt power?
Double check your ground.
Is the module inserted into the receptacle?
Is your inductive pickup installed correctly (5352 only).
If you have checked the above and are still having difficulty, call
Auto Meter customer service at (815) 895-8141
Note: On 4 cylinder applications light may flicker at low RPM.
SERVICE
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you
need the product back. If you need it back immediately mark the outside of the box "RUSH REPAIR," and Auto Meter will service product within two days after receiving it. ($10.00 charge will be
added to the cost of "RUSH REPAIR.") If you are sending product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
12 MONTH LIMITED WARRANTY
Auto Meter Products, Inc. warrants to the consumer that all Auto Meter High Performance products will be free from defects in material and workmanship for a period of twelve (12) months from date of the
original purchase. Products that fail within this 12 month warranty period will be repaired or replaced at Auto Meter's option to the consumer, when it is determined by Auto Meter Products, Inc. that the product
failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed the original purchase price of
the Auto Meter instruments nor shall Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred due to the failure of this product. Warranty claims to Auto Meter
must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in
duration to the said 12 month warranty period. Breaking the instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter
Products, Inc. disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by Auto Meter.
FOR SERVICE SEND TO: AUTO METER PRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 USA (815) 895-8141
Email us at autometer@autometer.com
2650-397F
8/17/99
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising