PLDT HOMEREPEATER
Package Contents:
● 1 x WiFi Repeater
● 1 x Quick Installation Guide
1. Overview
FrontView
LeftView
RightView
Back View
4
Reset
3
WPS
1
2
2
1 WPS : Press 1 second to trigger WPS function
PLDT HOMEREPEATER
3
Reset : Press 1 - 5 seconds to rebootRepeater.
Press > 5 seconds to reset to factory default and reboot.
4
AC Power Input
2 LED Indicators:
Power : On - Power On
Off - Power Off
WLAN : On - Wireless turn On
Off - Wireless turn Off
WPS : On - WPS feature turn On
Off - WPS feature turn Off
Blinking - WPStriggering
Signal Strength :1 LED On : Low Signal
2 LEDs On : Medium Signal
3 LEDs On : Good Signal
4 LEDs On : Excellent Signal
Wireless-N Repeater
Quick Installation Guide Revision 1.0
Note:
The illustration in this document may appear different from your model.
www.prolink2u.com
© Copyright 2014. PROLiNK® All rights reserved.
2. Hardware Installation
www.prolink2u.com
3. Connecting to the Root AP
Method 1 : With WPS button
Step 1. Plug the Wifi Repeater into the electrical socket and power on the electrical socket. The Power
LED
on Wifi Repeater will illuminate. Wait until the WLAN
and WPS
LEDs light
up.
Step 2. Press the Wi-Fi Protected Setup (WPS) button on your wireless router or root AP.
Smartphone
Tablet
Step 3. Press the WPS button of Wifi Repeater for 1 second until the WPS
LED starts to blink.
Note 1. The Signal Strength LEDs will illuminate to show the link quality once connected to
the root AP.
Note 2. Both buttons must be pressed within 2 minutes.
Wifi Repeater
LOCATION 1
Laptop
WPS
2 seconds
Wireless Router
2
Minutes
Cable/ DSL ModemRouter
LOCATION 2
1 second
Router WiFi Range
WiFi Repeater Range
WPS
WPS
Wifi Repeater
www.prolink2u.com
www.prolink2u.com
Within 2 Minutes
3. Connecting to the Root AP
3. Connecting to the Root AP
Method 2 : With Web Configuration
Step 1. Connect your computer to Wifi Repeater via wireless.
The wireless network (SSID) shall appear as “PLDTHOMEREPEATER”.
Note: The Wi-Fi Key or password can be found on the label pasted on Wifi Repeater.
Step 2. Open web browser and type http://192.168.1.253 in the browser’s address box. This
is the default IP address for Wifi Repeater.
The default user name is “admin” and password is “1234”.
Select the wireless network or root AP that you want to connect to, and click on <Next>.
Step 3. Click on Quick Setup Wizard -> Start
Key in the wireless password of the wireless router or root AP, and click on <Next> to
proceed.
Click <Next>, the repeater will scan and find the available wireless network.
www.prolink2u.com
www.prolink2u.com
3. Connecting to the Root AP
Wireless Password History
1.
Important:
Please obtain the wireless password
from the owner of the wireless router
or root AP.
The repeater will not able to connect
to the wireless router or root AP if the
password is incorrect.
2.
3.
4.
5.
Check and confirm if the information are correct.
Click <Finish> and the Wifi Repeater will attempt to connect to the root AP.
Note: The Signal Strength LEDs will illuminate to show the link quality once
connected to the root AP.
www.prolink2u.com
www.prolink2u.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising