low gear corded drill

low gear corded drill
INSTRUCTION MANUAL
LOW GEAR
CORDED DRILL
054-1343-0
TECHNICAL SPECIFICATIONS
4
SAFETY GUIDELINES
5–12
KEY PARTS DIAGRAM
13
OPERATING INSTRUCTIONS
14–20
MAINTENANCE
21–22
EXPLODED VIEW
23
PARTS LIST
24
WARRANTY
25–26
Read and understand this instruction manual thoroughly
before using the product. It contains important information for your safety as well as operating and maintenance
advice.
Keep this instruction manual for future use. Should this
product be passed on to a third party, then this instruction
manual must be included.
This symbol indicates that this tool is
listed by Underwriters Laboratories
as meeting both Canadian and U.S.
requirements.
LOW GEAR CORDED DRILL 054-1343-0
61TN
E213739
JD2155U
LOW GEAR CORDED DRILL 054-1343-0
TABLE OF CONTENTS
If any parts are missing or
damaged, or if you have
any questions, please call
our toll-free helpline at
1-800-689-9928.
3
5
Rating
120 V, 60 Hz, AC
Amperes
7A
Chuck speed
0–650 (no load)
Chuck
5/8" Keyed
Maximum drilling capacity in wood
1½" (38 mm)
Maximum drilling capacity in metal
5/8" (16 mm)
Weight
7 lb 1 oz (3.19 kg)
General safety warnings
! WARNING:
Before using this tool or any of its accessories, read this manual and
follow all Safety Rules and Operating Instructions. The important precautions, safeguards and
instructions appearing in this manual are not meant to cover all possible situations. It must be
understood that common sense and caution are factors which cannot be built into the product.
This instruction manual includes the following:
•
•
•
•
General Safety Rules
Specific Safety Rules and Symbols
Functional Description
Assembly
•
•
•
Operation
Maintenance
Accessories
EYE, EAR & LUNG PROTECTION
ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH CSA REQUIREMENTS or
ANSI SAFETY STANDARD Z87.1
FLYING DEBRIS can cause permanent eye damage. Prescription eyeglasses ARE
NOT a replacement for proper eye protection.
! WARNING:
Non-compliant eyewear can cause serious injury if broken during
the operation of a power tool.
! WARNING:
Use hearing protection, particularly during extended periods of
operation of the tool, or if the operation is noisy.
WEAR A DUST MASK THAT IS DESIGNED TO BE USED
WHEN OPERATING A POWER TOOL IN A DUSTY
ENVIRONMENT.
SAVE THESE INSTRUCTIONS FOR REFERENCE
LOW GEAR CORDED DRILL 054-1343-0
LOW GEAR CORDED DRILL 054-1343-0
SAFETY GUIDELINES
TECHNICAL SPECIFICATIONS
4
7
! WARNING: Dust that is created by power sanding, sawing, grinding, drilling, and
other construction activities may contain chemicals that are known to cause cancer, birth defects, or
other genetic abnormalities. These chemicals include:
• Lead from lead-based paints
• Crystalline silica from bricks, cement, and other masonry products
• Arsenic and chromium from chemically treated lumber
The level of risk from exposure to these chemicals varies, according to how often this type of work is
performed. In order to reduce exposure to these chemicals, work in a well-ventilated area, and use
approved safety equipment, such as a dust mask that is specifically designed to filter out microscopic
particles.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
Electrical safety
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
Electrical safety
WARNING: To avoid electrical hazards, fire hazards or damage to the tool, use
proper circuit protection.
This tool is wired at the factory for 120 V AC operation. It must be connected to a 120 V AC, 15 A circuit
that is protected by a time-delayed fuse or circuit breaker. To avoid shock or fire, replace power cord
immediately if it is worn, cut or damaged in any way.
Power tool safety
! WARNING: Read all safety warnings and all instructions. Failure to follow the
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the
risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a ground fault circuit interrupter (GFCI) reduces the risk of electric
shock.
Personal safety
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Work area safety
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
SAVE THESE INSTRUCTIONS FOR REFERENCE
LOW GEAR CORDED DRILL 054-1343-0
Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on
the switch or energizing power tools that have the switch on invites accidents.
SAVE THESE INSTRUCTIONS FOR REFERENCE
LOW GEAR CORDED DRILL 054-1343-0
SAFETY GUIDELINES
SAFETY GUIDELINES
6
8
SAFETY GUIDELINES
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
Hold power tools by insulated gripping surfaces when performing an operation where cutting tool
may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts
of the tool “live” and shock the operator.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
Service
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of dust collection can reduce dust-related hazards.
Specific safety rules
Power tool use and care
Know your drill. Do not plug the drill into the power source until you
have read and understand this Instruction Manual. Learn the tool’s applications and limitations,
as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
SAVE THESE INSTRUCTIONS FOR REFERENCE
LOW GEAR CORDED DRILL 054-1343-0
! WARNING:
Always wear eye protection. Any power tool can throw foreign objects into your eyes and cause
permanent eye damage. ALWAYS wear safety goggles (not glasses) that comply with ANSI safety standard
Z87.1. Everyday glasses have only impact resistant lenses. They ARE NOT safety glasses.
! WARNING:
Glasses or goggles not in compliance with ANSI Z87.1 could cause
serious injury when they break.
! WARNING: Always use a safety shield, hearing protection and dust mask when
drilling concrete.
Do not drill material too small to be securely held.
Always keep your hands out of the path of the drill bit. Avoid awkward hand positions where a sudden
slip could cause your hand to move into the path of the drill bit.
Secure the workpiece. Use clamps or a vice to hold the workpiece. It is safer than using your hand and it
frees both hands to operate the tool.
Make sure there are no nails or foreign objects in the part of the workpiece to be drilled.
SAVE THESE INSTRUCTIONS FOR REFERENCE
LOW GEAR CORDED DRILL 054-1343-0
SAFETY GUIDELINES
9
11
Always remove the plug from the power source before installing or removing a bit or accessory from the
chuck.
Extension cord safety
Do not install or use any drill bit that exceeds 7" (17.5 cm) in length or extends more than 6" (15 cm)
beyond the chuck jaws. They can bend or break suddenly.
Keep the extension cord clear of the working area. Position the cord
so it will not get caught on the workpiece, tools or any other obstructions while you are working with the
power tool.
Before starting the operation, jog the drill switch to make sure the drill bit does not wobble or vibrate.
! WARNING:
Do not use fly cutters or multiple-part hole cutters, because they can come apart or become unbalanced
during use.
Make sure any extension cord used with this tool is in good condition. When using an extension cord, be
sure to use one of heavy enough gauge to carry the current the tool will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating.
Make sure the spindle has come to a complete stop before touching the chuck or attempting to change
the drill bit.
The table below shows the correct size to use according to cord length and nameplate ampere rating. If
in doubt, use the next heavier gauge. The smaller the gauge number the heavier the cord.
Always make sure the chuck is tight and the drill bit firmly tightened in the chuck before starting drill.
Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. Protect your extension cord from
sharp objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your power tools. This circuit must not be less than 14 gauge wire
and should be protected with either a 15 A time delayed fuse or circuit breaker. Before connecting the
power tool to the power source, make sure the switch is in the OFF position and the power source is the
same as indicated on the nameplate. Running at lower voltage will damage the motor.
MINIMUM GAUGE (AWG) EXTENSION CORDS (120 V use only)
Amperage rating
Total length
More
Not more
25'
50'
100'
150'
than
than
(7.5 m)
(15 m)
(30 m)
(45 m)
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not Applicable
LOW GEAR CORDED DRILL 054-1343-0
LOW GEAR CORDED DRILL 054-1343-0
SAFETY GUIDELINES
SAFETY GUIDELINES
10
12
13
KEY PARTS DIAGRAM
SAFETY GUIDELINES
Symbols
! WARNING:
Some of the following symbols may appear on the drill. Study these
symbols and learn their meaning. Proper interpretation of these symbols will allow for more
efficient and safer operation of this tool.
V …............
A ………...
Hz ………
W ……….
kW ...........
Volts
Amperes
Hertz
Watts
Kilowatts
...
……….. No load speed
……….
........
L ………...
Kg ………
H ………...
N/cm2 .......
Microfarads
Litres
Kilograms
Hours
Newtons per square
centimetre
Pa ……… Pascals
OPM …..
Oscillations per minute
Min …….
Minutes
S ………... Seconds
or AC …...
Three-phase alternating
current
..
Three-phase alternating
current with neutral
…..
Read all safety warnings
and instructions
Alternating or direct current
………. Class II construction
….......... Splash-proof construction
…….. Watertight construction
………. Protective grounding at
grounding terminal, Class I
tools
… Revolutions or reciprocations
per minute
Alternating current
..
Direct current
0
…........... Diameter
………….. Off position
……. Arrow
……...
……….
Warning symbol
Wear your safety glasses
……... Wear hearing protection
LOW GEAR CORDED DRILL 054-1343-0
No.
Description
No.
Description
1
Side assist handle
5
Lock-on switch
2
Air vent
6
Variable speed trigger switch
3
Swivelling “D” handle
7
Forward/reverse switch
4
Chuck key
8
Chuck
LOW GEAR CORDED DRILL 054-1343-0
14
OPERATING INSTRUCTIONS
Install side assist handle
! WARNING:
2.
fig.11
fig
The side assist
handle must be installed as it will provide
additional control over the drill during heavy
drilling operations.
Lock-on switch
To install the side assist handle (1), simply thread
it CLOCKWISE into the threaded hole (2) in the top
of the drill (fig. 1).
NOTE: Never use a wrench or pliers to tighten
the assist handle into the drill. Hand tighten the
handle.
The lock-on switch is available to hold the ON/
OFF switch in the ON position during prolonged
operation of the drill. To lock the ON/OFF switch in
the ON position:
Forward/reverse switch
The forward/reverse switch (1) is conveniently
mounted immediately above the trigger switch on
the drill handle (2) (fig. 2). To make the drill rotate
clockwise for drilling, push the forward/ reverse
switch to the left. To make the drill rotate counterclockwise, push the forward/reverse switch to
the right.
Squeeze the switch trigger (3) (fig. 4).
2.
While squeezing the switch trigger, press
the lock-on button (4) into the drill handle
(2).
3.
While holding the lock-on button into the
drill handle, release the switch trigger. The
drill will continue to run.
4.
To turn the drill OFF while the lock-on button
is holding the trigger switch ON, squeeze
and then release the trigger.
fig.
fig 44
Installing drill bits
! WARNING:
Variable speed trigger switch
1.
1.
fig.22
fig
NOTES:
a) Never change the position of the forward/
reverse switch while the chuck is turning.
b) The trigger switch will NOT function with the
forward/reverse switch in the middle position.
This drill is equipped with a variable-speed ON/
OFF trigger switch.
To stop the drill, release the trigger switch.
NOTE: Drilling at a slow speed for an
extended period of time may cause the drill
motor to overheat. If the drill gets hot, stop
drilling and allow it to cool for at least 15
minutes.
fig.33
fig
To start the drill, gently squeeze the trigger
switch (3) (fig. 3).
NOTE: The drill will turn at its slowest
speed when the trigger switch is depressed
slightly. The drill will turn at its fastest speed
when the trigger switch is fully depressed.
LOW GEAR CORDED DRILL 054-1343-0
Never hold the
chuck body with one hand and use the drill
power to rotate the drill body to loosen or
tighten bits. Serious injury may result.
1.
Remove the drill plug from the power
source.
LOW GEAR CORDED DRILL 054-1343-0
OPERATING INSTRUCTIONS
15
16
17
Rotate the chuck collar (1) to open or close
the jaws (2) to a point where the opening is
slightly larger than the bit size you intend to
use (fig. 5).
3.
Insert the bit into the chuck the full length of
the jaws. Raise the front of your drill slightly
to prevent the bit from falling out of the
chuck jaws.
4.
Insert the chuck key (3) into one of the three
holes in the chuck body. Rotate the chuck
key clockwise until the drill bit is held firmly
in place by the chuck jaws.
NOTE: Do not use a wrench on the chuck
key. You may damage the key or the chuck.
! WARNING: Do not insert
the drill bit into the chuck and tighten as
shown in fig. 6. The drill bit MUST be properly
inserted with all three chuck jaws holding the
bit centered in the chuck. Failure to properly
insert the drill bit could cause the drill bit to
be thrown from the chuck resulting in possible
serious injury or damage to the chuck.
fig.
fig 55
Removing bits
1.
Remove the drill plug from the power
source.
2.
Insert the chuck key into one of three
holes in the chuck body. Rotate chuck key
counter- clockwise until the chuck jaws
release the drill bit.
NOTE: Do not use a wrench on the chuck
key or you may damage the key or chuck.
3.
Remove the drill bit.
! WARNING
fig.
fig 6
Have you read "GENERAL SAFETY WARNINGS",
"POWER TOOL SAFETY", "SPECIFIC SAFETY
RULES", "EXTENSION CORD SAFETY" and
"SYMBOLS" on pages 5 through 12 of this
Instruction Manual? If not, please do it now
before you operate this drill. Your safety
depends on it!
Every time you use the drill you should
verify the following:
1. Chuck is tight.
2. Workpiece is properly secured.
3. Safety glasses are being worn.
Failure to adhere to these safety rules can
greatly increase the chances of injury.
LOW GEAR CORDED DRILL 054-1343-0
LOW GEAR CORDED DRILL 054-1343-0
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
2.
18
OPERATING INSTRUCTIONS
Drilling
fig.
fig 7
When drilling in smooth hard surfaces such as
metal, use a centre punch to mark the desired
hole location. This will prevent the drill bit from
slipping off centre as the hole is started.
The workpiece to be drilled should be secured in a
vise or with clamps to keep it from turning as the
drill bit rotates (fig. 7).
1.
Check the drill bit to make sure it is firmly
locked into the drill chuck and the forward/
reverse switch is in the forward position.
2.
Hold the drill firmly with both hands. Use
your left hand to grasp the main handle
and switch and your right hand to grasp the
side assist handle (fig. 7). If the side assist
handle cannot be used due to inadequate
space, use your right hand to grasp the
swivelling “D” handle (fig. 8).
3.
While holding the drill firmly, place the point
of the drill bit at the point to be drilled.
Squeeze the switch trigger to start the drill.
NOTE: Always use a higher drill speed when
drilling small holes. Use a slower drill speed
when drilling large holes.
4.
Move the drill bit into the workpiece applying only enough pressure to keep the bit
cutting. Do not force the drill bit or apply
sideways pressure to elongate the hole.
When drilling metals, use a light oil on the drill bit
to keep it from overheating. The oil will prolong
the life of the drill bit and improve the drill cutting
action. If the bit jams in the workpiece or if the
drill stalls, release the switch trigger immediately.
Remove the bit from the workpiece and determine
the reason for jamming.
Driving screws
When driving screws, care must be taken to use
the bit that correctly fits the screw being driven.
Make sure you use the largest bit size that will
properly fit into the head of the screw.
1.
Select the correct screwdriver bit for the
screw being driven.
2.
Fasten the screwdriver bit into the chuck,
making sure the flats of the bit are gripped
by the chuck jaws.
fig.
fig 8
! WARNING: Be prepared for
binding and bit breakthrough. When these
situations occur, the drill bit has a tendency to
grab the workpiece. This action will kick the
drill opposite to the direction of the drill bit
rotation and could cause loss of control when
breaking through material as you complete
drilling the hole. If you are not prepared, this
loss of control can result in possible serious
injury.
LOW GEAR CORDED DRILL 054-1343-0
NOTES:
a) If the material is particularly soft or porous, run
the drill at slower speeds to avoid over-driving
the screw.
b) Hold the drill firmly with both hands while
driving screws to avoid loss of control.
Chuck removal
The drill chuck must be removed in order to use
some accessories. To remove the chuck:
1.
Remove the drill plug from the power
source.
2.
Insert a 5/16" or larger hex key (1) into
the chuck (2) and tighten the chuck jaws
securely. Make sure each of the three chuck
jaws (3) is seated on the flat surfaces of the
hex key (fig. 9).
fig.
fig 9
LOW GEAR CORDED DRILL 054-1343-0
OPERATING INSTRUCTIONS
19
20
21
Tap the hex key sharply with a mallet (4)
in a CLOCKWISE direction. This action will
loosen the screw in the chuck for easy
removal.
4.
Open the chuck jaws and remove the hex
key.
5.
Open the chuck jaws as far as possible.
6.
Remove the chuck screw using a
#2
screwdriver (fig. 10).
NOTE: Turn screw CLOCKWISE to remove it.
This screw has a left hand thread.
7.
Insert the hex key into the chuck and tighten
the jaws of the chuck securely (fig. 11).
Tap the hex key sharply with a mallet in a
COUNTER-CLOCKWISE direction. This will
loosen the chuck on the spindle. The chuck
can now be unscrewed and removed from
the spindle by hand.
4.
Tighten the chuck screw using a
#2
screwdriver.
NOTE: Turn the screw COUNTERCLOCKWISE to tighten it. This screw has a
left hand thread.
MAINTENANCE
OPERATING INSTRUCTIONS
3.
Replacing carbon motor
brushes
fig.
fig 10
fig.
fig 11
The carbon motor brushes will wear down and
require replacing. The time intervals between
replacements will vary depending upon the
working environment and the hours of use. It
is recommended that the brushes be checked
after each 10 hours of use. When the length of
the carbon brush reaches 1/4" (6.35 mm), the
brushes should be replaced.
! WARNING: Unplug the tool
from the power source.
Retightening a loose chuck
After installing the chuck once it has been
removed, the chuck may become loose on the
spindle and develop a wobble. Also, the chuck
screw may become loose, causing the chuck jaws
to bind and prevent them from closing. To tighten
the chuck, follow these steps:
1.
Insert the hex key into the chuck and tighten
the chuck securely.
2.
Tap the hex key sharply with a mallet in
a CLOCKWISE direction (fig. 9). This will
tighten the chuck on the spindle.
3.
Open the chuck jaws and remove the hex
key.
LOW GEAR CORDED DRILL 054-1343-0
1.
Use a 3/16" (5 mm) slot screwdriver and
remove one brush cap (1) (fig. 12). Turn the
brush cap counter-clockwise to remove it
from the motor housing.
2.
Pull the spring & brush assembly (2) from
the brush holder (3) in the motor housing
(4).
3.
Insert the new spring & brush assembly into
the motor housing.
4.
Compress the spring into the brush holder
and thread the brush cap back into the
motor housing.
NOTE: Make sure the brush cap threads are
not cross-threaded. Do NOT over tighten.
5.
Repeat steps 1 to 4 to replace the second
carbon brush located on the opposite side of
the motor housing.
fig.
fig 12
LOW GEAR CORDED DRILL 054-1343-0
22
23
! WARNING:
EXPLODED VIEW
MAINTENANCE
General
When servicing,
use only identical replacement parts. The use
of any other part may create a hazard or cause
product damage.
DO NOT use solvents when cleaning plastic
parts. Plastics are susceptible to damage from
various types of commercial solvents and may be
damaged by their use. Use a clean cloth to remove
dirt, dust, oil, grease etc.
! WARNING:
Do not allow
brake fluids, gasoline, petroleum-based
products, penetrating oils, etc. to come into
contact with plastic parts. They contain
chemicals that can damage, weaken or
destroy plastic.
DO NOT abuse power tools. Abusive practices can
damage the tool and the workpiece.
! WARNING:
DO NOT attempt
to modify tools or create accessories. Any
such alteration or modification is misuse and
could result in a hazardous condition leading
to possible serious injury. It will also void the
warranty.
Lubrication
All of the bearings in this tool are lubricated with
a sufficient amount of high-grade lubricant for the
life of the unit under normal conditions. Therefore,
no further lubrication is required.
LOW GEAR CORDED DRILL 054-1343-0
LOW GEAR CORDED DRILL 054-1343-0
25
! WARNING:
3
When servicing, use only Mastercraft® replacement parts. The use of any
other parts may create a safety hazard or cause damage to the drill.
LIMITED WARRANTY†
DE GARANTIE LIMITÉE†
Any attempt to repair or replace electrical parts on this drill may create a safety hazard unless repairs are
performed by a qualified technician. For more information, call the Toll-free Helpline, at
1-800-689-9928.
Always order by PART NUMBER, not by key number.
Key #
Part #
Part Name
Qty
Key #
Part #
Part Name
Qty
1
4.02E+09
Screw M6x25 (Left)
2
24
1.01E+09
Rotor
1
2
1.14E+09
Chuck
1
25
3.15E+09
Shaft clamp ring
1
3
2.04E+09
Shaft
1
26
3.14E+09
Rubber column
1
4
4.12E+09
Flat key
1
27
4.01E+09
Bearing 608-2Z
1
5
2.02E+09
Bearing retaining ring
1
28
4.03E+09
Screw ST4.9x55
2
6
4.01E+09
Bearing 6202-2Z
1
29
3.15E+09
Air baffle
1
7
2.02E+09
Gearbox
1
30
1.02E+09
Stator
1
8
3.14E+09
Rubber column
1
31
3.15E+09
Stator clamp
2
9
4.01E+09
Bearing 626-2Z
1
32
3.12E+09
FWD/REV level
1
10
2.01E+09
Duplex gear shaft
1
33
1.062E+09
Switch
1
11
2.04E+09
Duplex gear
1
34
3.12E+09
Handle
1
12
3.15E+09
Bakelite washer
1
35
4.03E+09
Screw ST3.9x19
2
13
4.01E+09
Needle bearing BK0609
1
36
4.03E+09
Screw ST4.9x25
4
14
2.02E+09
Gearbox cover
1
37
3.14E+09
Cord guard
1
15
4.05E+09
Screw M12x50
1
38
1.19E+09
Plug
1
16
4.03E+09
Screw ST4.9x35
4
39
1.14E+09
Chuck key
1
17
2.01E+09
Shaft sleeve
1
40
3.12E+09
Back handle
1
18
2.04E+09
Big gear
1
41
4.03E+09
Screw ST3.9x19
4
19
4.1E+09
Snap ring 14x1
1
42
3.011E+09
Housing
1
20
4.01E+09
Needle bearing BK0810
1
43
1.23E+09
Brush holder assembly
2
21
3.14E+09
Rubber column
1
44
1.23E+09
Brush
2
22
4.01E+09
Bearing 608 2RS
1
45
3.15E+09
Brush holder cap
2
23
3.14E+09
Sealing ring
1
46
3.12E+09
Auxiliary handle
1
LOW GEAR CORDED DRILL 054-1343-0
YEAR
ANS
This Mastercraft® product is guaranteed for a period of three years from the date of original retail
purchase against defects in workmanship and materials, except for the following components:
a.
b.
Component A: Batteries, chargers and carrying case, which are guaranteed for a period of two
years from the date of original retail purchase against defects in workmanship and materials;
Component B: Accessories, which are guaranteed for a period of one year from the date of original
retail purchase against defects in workmanship and materials.
Subject to the conditions and limitations described below, this product, if returned to us with proof
of purchase within the stated warranty period and if covered under this warranty, will be repaired or
replaced (with the same model, or one of equal value or specification), at our option. We will bear the cost
of any repair or replacement and any costs of labour relating thereto.
These warranties are subject to the following conditions and
limitations:
a.
b.
c.
d.
e.
f.
A bill of sale verifying the purchase and the purchase date must be provided;
This warranty will not apply to any product or part thereof that is worn, broken or that has become
inoperative due to abuse, misuse, accidental damage, neglect or lack of proper installation,
operation or maintenance (as outlined in the applicable owner’s manual or operating instructions)
or that is being used for industrial, professional, commercial or rental purposes;
This warranty will not apply to normal wear and tear or to expendable parts or accessories that
may be supplied with the product and that are expected to become inoperative or unusable after a
reasonable period of use;
This warranty will not apply to routine maintenance and consumable items, including, but not
limited to, fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids, tune-ups or adjustments;
This warranty will not apply where damage is caused by repairs made or attempted by others (i.e.:
persons not authorized by the manufacturer);
This warranty will not apply to any product that was sold to the original purchaser as a reconditioned or refurbished product (unless specified otherwise in writing);
LOW GEAR CORDED DRILL 054-1343-0
WARRANTY
PARTS LIST
24
26
WARRANTY
g.
h.
i.
This warranty will not apply to any product or part thereof if any part from another manufacturer
is installed therein or any repairs or alterations have been made or attempted by unauthorized
persons;
This warranty will not apply to normal deterioration of the exterior finish, including, but
not limited to, scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive
and chemical cleaners; and
This warranty will not apply to component parts sold by and identified as the product of another
company, which shall be covered under that product manufacturer’s warranty, if any.
Additional Limitations
This warranty applies only to the original purchaser, and cannot be transferred. Neither the retailer nor
the manufacturer shall be liable for any other expense, loss or damage, including, without limitation, but
not limited to any indirect, incidental, consequential or exemplary damages arising in connection with the
sale, use or inability to use this product.
Notice to Consumer
This warranty gives you specific legal rights, and you may have other rights, which may vary from
province to province. The provisions contained in this warranty are not intended to limit, modify, take
away from, disclaim or exclude any statutory warranties set forth in any applicable provincial or federal
legislation.
Mastercraft is a superior line of products selected for their workmanship and materials. These products
are designed to meet rigorous quality and performance standards, and are approved by our Quality
Assurance laboratory.
TOLL-FREE HELPLINE: 1-800-689-9928
LOW GEAR CORDED DRILL 054-1343-0
Rev 1.10 24/06/2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising