Drive 3G-FLEX - Wilson Amplifiers
Note:
How It Works
The Drive 3G-FLEX cellular signal booster is a effective solution to
all those times you have lost a call while driving your vehicle due to
a weak cell signal. Installation is simple and can be completed with
minimal tools.
IT IS VERY IMPORTANT TO POWER YOUR SIGNAL BOOSTER USING A SURGE PROTECTED AC
POWER STRIP WITH AT LEAST A 1000 JOULE RATING. FAILURE TO DO THIS WILL VOID YOUR
WARRANTY IN THE EVENT OF A POWER SURGE OR LIGHTNING STRIKE.
ENGLISH
Your cell phone is an essential part of your life. weBoost is here to
ensure you have seamless connections on all your cellular devices.
THE SIGNAL BOOSTER UNIT IS DESIGNED FOR USE IN AN INDOOR, TEMPERATURE-CONTROLLED
ENVIRONMENT (LESS THAN 150 DEGREES FAHRENHEIT). IT IS NOT INTENDED FOR USE IN ATTICS
OR SIMILAR LOCATIONS SUBJECT TO TEMPERATURES IN EXCESS OF 150°F.
®
FRANÇAIS
Outside Antenna
Signal Received and
Transmitted
Drive 3G-FLEX
Power Supply
Drive 3G-FLEX
Quick Install Guide
For more information refer to full Install Guide at:
www.weboost.com/us/installguide/drive3G-FLEX
Package Contents
Product Registration
Thank you for purchasing this weBoost product. Please take time to
register your new product at our website:
NEED ASSISTANCE? WE CAN HELP!
Drive 3G-FLEX
Mini-Magnet Antenna
AC/DC Power Supply
USB Cable w/Power Adapter
Antenna Window Mount
Dash Mounting Kit
TM
Contact our U.S.-BASED CUSTOMER SUPPORT:
www.weboost.com/us/productregistration
Registering is quick and easy, it only takes 2-3 minutes to complete.
Your information is secure, we don’t share or sell your information
to other third parties.
n C
ontact our U.S.- based customer support team at
1-866-294-1660 o
r email at support@weboost.com
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
n Go online for how to resolve the most common issues at
www.weboost.com/us/support
Cellular Signal Booster
Quick Install
Diagram
460101
Outside Antenna Installation
Running Antenna Cable
RF Safety: Any antenna used with this device must be located at least 8 inches from all persons.
FCC ID: PWO460013
IC: 4726A-460013
n Find a weBoost Installer on our web site at
www.weboost.installernet.com
Connect Cable to Drive 3G-FLEX / Power Supply Cord
Need help?
www.WilsonElectronics.com
Tech Support 866-294-1660
Mon.- Fri. Hours: 7 am to 6 pm MST
Connect Power Supply
111568_Rev02_01.30.15
ENGLISH
3301 East Deseret Drive, St. George, UT 84790
email: support@weboost.com
web: www.weboost.com
local: 435-673-5021
fax: 435-656-2432
phone: 866-294-1660
Installation is simple, but we’re here to make it even easier.
Mount Dash Bracket
FRAN
1
2
Outside Antenna Installation
Select a location on top of the vehicle to mount the Mini-Mag
Mount Antenna that is:
n
n
Near the center of the vehicle’s
roof.
At least 12 inches from any
other antennas.
n
n
Free of obstructions.
At least 6 inches from any
windows (including sunroofs).
3
Running Antenna Cable
un the Outside Antenna cable into the car. The cable is strong
R
enough that it may be shut in most vehicle doors without damaging
the cable. For a cleaner look, carefully pull down the door seal, run
the cable under the seal, and push the seal back into place. This
method reduces wear on the cable as the door opens and closes.
Connect Coax Cables to Drive 3G-FLEX
Connect the cable from the Mini-Mag Mount Antenna to the port
labeled “Antenna” on the Drive 3G-FLEX.
Drive 3G-FLEX
Mini-Mag Mount Antenna
4
Connect Power Supply to Drive 3G-FLEX
Connect the power cable to the mini-USB port on the bottom of the
Drive 3G-FLEX.
5
6
Connect to Power Supply
Plug the power adapter into vehicle’s 12V DC power supply. If your
Drive 3G-FLEX is working correctly, the lights will be green.
NOTE: If lights are not green, please refer to the full install guide
online or contact customer support at 1-866-294-1660 or email at
support@weboost.com.
Mount Dash Bracket (optional).
Clean the area where the bracket is to be mounted with the alcohol
wipe included. Allow the area to dry. Peel the backing to expose
the adhesive and press the bracket onto the desired location on
the dashboard.
Drive 3G-FLEX
DC Power Adapter
Vehicle’s Power Supply
Dash Mount Bracket
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising