EZ-One Woodworking Center

EZ-One Woodworking Center
EZ-One Woodworking Center
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Phone (352) 620-2262 Fax (352) 620-2576
techsupport@eurekazone.com www.eurekazone.com
v14-01
EZ-ONE WOODWORKING CENTER
When using the EZ-One Woodworking Center [EZ-One] with any power tool, be sure you
have read and understand the operating manual for the tool before operation. Be sure
to use the tool safely. Do not disable any built-in safety features. Be sure to follow safe
practices when using the EZ-One with your power tools. If a task seems like it might be
potentially unsafe, do not attempt. Do not operate any tool on the EZ-One if you are
tired or distracted in any way.
Step 1
Assemble the Frame Kit
Parts
50” Side Rails (2)
24” End Rails (2)
Frame Corner Set (2)
●
Assemble as shown. Lightly tighten all nuts.
Note: The end of the End Rails should not block the
outer slot of the Side Rails.
Step 2
Square the Frame
Parts
Squaring Rod w/ Hardware
●
●
Step 3
Install Squaring Rod in bottom T-slot of Rails,
across one corner.
Adjust frame as needed until it is square.
Note: The End Rails can be adjusted in the overlapping
of the Side Rails to assist in squaring the frame. The
frame need not be perfectly square so long as the
Sliding Fences are parallel to the front End Rail and the
Bridge is perpendicular the Fences and End Rail
Attach the Legs
Parts
34” Legs (4)
●
●
Install Legs into Framer Corners with wide face of
Legs facing outward.
Tighten nuts on the connectors.
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Page 1
Phone (352) 620-2262 Fax (352) 620-2576
techsupport@eurekazone.com www.eurekazone.com
v14-01
Step 4
Attach Shoes and Braces
Parts
24” Brace (2) w/ T-slot hardware
Shoes (4)
●
●
Insert Shoes into inner slot of the Legs
Install Brace using the outer T-slots of the Legs
Note: Shoes are adjustable to accommodate for
floor irregularities.
Step 5
Install the Sliding Fences
Parts
Sliding Brackets (3 pair)
48” Squaring Fence
42” Sliding Fence (2)
●
●
●
●
Step 6
Install Sliding Brackets for the Squaring Fence
with the top knob facing away from the front end
of the Frame. The other sets have the knob
facing toward the front end.
Install the Fences so that the pre-cut kerfs line up
with each other.
Ensure the Squaring Fence is parallel to the front
End Rail and square to the Side Rails.
Adjust as needed for squareness and ease of
sliding the fences.
Install the Bridge
Parts
B-300 Bridge (Front and Rear Units)
●
●
●
●
Place the Bridge Units at desired location
corresponding to pre-cut kerf in Sliding Fences.
Slide Rail into Rail Supports of both Bridge Units.
Raise the Bridge as shown. Rail Support should
be 12” from the front of the Rail. Tighten the
connectors.
Lower the Bridge and square the Rail to the
Squaring Fence. Make adjustments to Bridge and
Rail as needed.
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Page 2
Phone (352) 620-2262 Fax (352) 620-2576
techsupport@eurekazone.com www.eurekazone.com
v14-01
Step 7
Install the Blade Depth Guide
Parts
Blade Depth Guide w/ Knob and Connector
●
Install the Blade Depth Guide adjacent to the
front unit of the Bridge.
Note: When making a cut, position the material
under the Rail and lower the blade of the saw until it
just touches the top of the Depth Guide.
Step 8
Fine Tuning
Once the assembly of the EZ-One is complete, be sure to do some test cuts and make adjustments as
necessary.
The Sliding Fences should not bind as they move along the Side Rails. If binding occurs, adjustments may
need to be made at the Frame Corners. Verify that the Frame remains square after each adjustment.
If the EZ-One is moved from one location to another, it is best to check for squareness prior to use.
Extras
Sliding Modules: The built-in lip on the Squaring and Sliding Fences allows for a piece of 3/4” plywood to
be placed between two fences to serve as a work top or as additional material support. These modules can
be made to your desired dimensions. Additionally, custom modules can be made for various woodworking
jigs such as for mortise & tenons, dovetails, or for cutting reproducible parts. The open top nature of the
EZ-1 allows for maximum versatility to best suit the woodworking task at hand.
Using the Stops:
1. Six-Way Stops: These stops can be used to hold a workpiece in
place at its four corners for cutting or routing and can also be used
as stops for ripping or cross-cutting.
2. Sliding Cross-Stop: These two 18” stops can be used on the
Squaring fence to provide a square edge for the workpiece and can
also be used on the Sliding Fences as cross-cut stops. The end with
the set screws allows positioning under the Bridge.
3. Limit Stop: Can be used in conjunction with the Sliding CrossStop as a stop block for cross-cutting or ripping.
The next page shows some of the many uses for the various stops.
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Page 3
Phone (352) 620-2262 Fax (352) 620-2576
techsupport@eurekazone.com www.eurekazone.com
v14-01
USE OF STOPS
Trapping workpiece using the Six-Way Stops
Cross-cutting using the Six-Way Stops
Ripping using the Six-Way Stops
Limit Stop used for cross-cutting or ripping
Using Sliding Stops as fence for ripping
Extending the range using the Limit Stop
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Page 4
Phone (352) 620-2262 Fax (352) 620-2576
techsupport@eurekazone.com www.eurekazone.com
v14-01
OTHER USES
As a versatile workstation, the EZ-One has many uses beyond cutting with a circular saw on the EZ SMART
Guide Rail. It can be combined with other EUREKAZONE products (sold separately) to increase its utility.
Below are some of the examples that unlock the potential for the EZ-One.
Assist with clamping and assembly
Routing using the EZ SMART Super Router Kit
Breaking down panels with the EZ-One Raised Top
Kit* and the EZ SMART Universal Edge Guide*
* Sold separately
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470
Page 5
Phone (352) 620-2262 Fax (352) 620-2576
techsupport@eurekazone.com www.eurekazone.com
v14-01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising