toshiba - Sears Parts Direct

toshiba - Sears Parts Direct
TOSHIBA
IMPORTANT
NOTE
Before
connecting,
operating,
oradjusting
thisproduct,
carefully
readtheImportant
Safety,
Installation,
Care,
andService
information
intheInstallation
Guide,
Foranoverview
ofsteps
forsetting
upyournewTV,seepage
4.
Note:To displaya HighDefinitionpicture,theTVmust bereceivinga
HighDefinitionsignal(suchasan over:the-airHighDefinitionTV
broadcast,
a HighDefinitiondigital cableprogram,or a HighDefinition
digital satelliteprogram).FOrdetails,pleasegontadyourTVanteana
instaiier,cabieprovider,or sateiiiteprovider.
Note:!f the rV is poweredoti and_henquicklyon againwhenthe
]ampunii is hot,it may_akeseveralminutesfor the pictureto appear
on:screen.This is a propertyof DLP_TV [amptechnologyand is NOT
a sign of malfunction.Fordetaib, see'IMPORTANT
NOTICEABOUT
HOTLAMPRESTART"
on page2.
HM66
ENbook
Page 2 Tlmrsdav
Februa W 23 2006
CAUTION:
the Toshiba
2:49 PM
This television is for use only with
stand indicated below. Use with other
carts or stands is capable of resulting
instability, causing possible injury.
Television
Stand Model
50HM66
ST5066
56HM66
ST5666
in
Welcometo Toshiba
Thank you for purchasing this Toshiba TV, one of the most
innovative DLP "lxfprojection TVs on the market. We have
provided two separate guides to facilitate the installation and
operation of your TV.
Please use the Guides in the order shown below to get the most
enjoyment
from your new TV.
• The "h*smllation GuMe" explains tmw to connect your TV to
your antenna and equipment.
• The "Operating GuMe" (this Guide) provides step-by-step
instructions for using your TV's many features.
importantnotesabeut your
B£PrMprejectien Tg
1) The light source for this TV is a projection lamp unit with a
limited service life. When the lamp wears out, the picture
may become dark or black or the lamp may fail, at which time
you must replace the lamp unit. See "Lamp unit replacement
and care" (re pages 47-49).
2) When the lamp mode is set to Low Power, every time the
TV is powered on, the lamp will initially be in High Bright
mode but will switch to Low Power mode after a short
period of time. You may notice a change in screen brightness
when this happens. This is normal and is not a sign of
malfunction.
(r_ page 42 for details.)
3) Every time the TV is powered on, it may take several minutes
for the picture to obtain full brightness (t_¢"IMPORTANT
NOTICE ABOUT "HOT LAMP RESTART," at right).
4) The TV's display is manufactured using an extremely high
level of precision technology; however, an occasional pixel
(dot of light) may show constantly on the screen. This is a
structural property of DLP "lxf(Digital Light i%'ocessing "lxf)
technology and is not a sign of malfunction. Such pixels are
not visible when the picture is viewed from a normal viewing
distance.
5) Always sit approximately
10-25 feet away from the TV and
as directly in front of it as possible. The picture quality may
be affected by your viewing position and length of viewing
time. If you sit too closely to the TV for too long, you may
suffer from eye fatigue. See item 29 of the "care" information
in the separate Installation Guide.
6) Depending on the media you are viewing, it is possible,
although unlikely, that a limited number of viewers may see
a "rainbow effect" on the screen, w,hich can, in rare instances,
result in eye fatigue. This is a rare occurrence related to DLP
technology and is not a sign of TV malfunction.
7) This TV contains several cooling fans to moderate the
internal temperature. You may be able to hear the
fans for several minutes after the TV is turned off.
This is a function of the Quick RestarO x_feature
and is not a sign of TV malfunction. You can set
the Quick RestarO xffeature to stop the fans as soon as the TV
is powered off. See "Setting the Quick RestarO xf feature"
(r_ page 20).
8) The yellow and blue LED lights at the bottom center of the
TV front indicate your TV's current status. If either light
flashes, see "LED indications" (re page 46).
9) Every time the TV power cord is plugged in, the yellow LED
will blink until the TV enters standby mode (plugged in but
not powered on). This is normal and is not a sign of
malfunction.
"Voice announce" feature
When certain non-standard conditions occur, the LEDs on
the TV will blink and the TV will play a recorded
"voice announcement" describing the condition (see the
LED indication table on page 46 for the specific conditions
that include a voice announcement).
To repeat the voice announcement and hear additional
information, press the MENU button on the TV while the
LEDs are blinking.
IMPORTANTNOTICEABOUT"NOT LAMP RESTART"
When the TV has been powered on long enough for the lamp
unit to get hot, it may take several minutes for the picture to
appear on-screen in the following situations:
• When the Quick Restart TM feature is set to OFF and
you turn the TV off and then on again within a few
minutes; or
• If the TV is on when a short-term power failure, power
surge, or other similar power failure occurs, such that
the TV loses and regains power within a few minutes,
This is a property of DLP TV lamp technology and is
NOT a sign of malfunction.
If this occurs, the yellow LED on the TV front panel will blink
(and the blue LED will be lit solid) until the TV is finished
restarting the lamp and the normal picture appears. If both
LEDs are blinking, you will need to turn the TV off and then
on again to restart the lamp.
#ademm'k infermatien
• This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights. Use
of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
• WOW, SRS and (e) symbol are trademarks of SRS Labs, Inc.
WOW technology is incorporated under license from SRS Labs, Inc.
• *Manufactured under license from Dolby Laboratories. Dolby and
the double-D symbol are registered trademarks of Dolby
Laboratories.
• CableCARD
TM
is a trademark
of Cable Television Laboratories,
Inc.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
• Digital Light Processing TM, DLP TM and the DLP TM medallion
trademarks of Texas Instruments.
are
HM66 (E/F) Web 213:276
HM66
ENbook
Page 3 Thursday, Febnta W 23, 2006
2:49 PM
Chapter 1: Introduction ............................
Features of'tour new TV ............................
Overview of steps for installing, setting up, and using
your new TV ..................................
TV l?'ont and side panel controls and connections .........
TV back panel conuectious ...........................
Chapter2: Usingthe
remote control...................
Prepm'iug the remote control for use ....................
Installing the remote control batteries ..................
Remote control efl_:ctive rauge ........................
Learning about the remote control .....................
Usiug the remote control to control your other devices .....
Remote Control functional key chart ..................
Programming
tile remote control to control your other
devices ......................................
Remote control codes ..............................
Chapter3:
4
4
4
5
6
7
7
7
7
8
9
10
I1
12
IVlenu layoutandnavigation.................
Main menu la2rout .................................
Setup/Installation
menu layout .......................
Navigating the menu system .........................
14
14
15
15
Chapter 4: Setting up your IV ........................
Selecting the menu lmlguage ........................
Configuring the autenna input sources for the ANT 1
and ANT 2 terminals ...........................
16
16
Programming channels into the TV's channel memory ....
Programmiug
channels automatically
..............
Manually adding and deleting channels in the chanuel
memory ..................................
Programmiug your lavorite channels ..................
Setting the ColorStream HD audio mode ...............
Setting the HDMP x_audio mode .....................
Viewiug the CableCARD I_1menu ....................
Settiug the Quick Restart Ix1feature ...................
Viewiug the digital signal meter ......................
Viewiug the system status ...........................
Chapter 5: Using the TV's basic features ................
Selecting the video input source to view ...............
Labeling the video input sources .....................
Tuning chamlels ..................................
Using the Cha*mel Browser jx_ ....................
Tuuing your favorite cha*mels ....................
Tuning to the next programmed cham_el ............
Tuning to a specific cha*mel (programmed
or
unprogrammed)
............................
Switching between two chanuels using Channel
Return ...................................
Adjusting the audio quality ......................
Using the StableSound ® feature ...................
17
17
17
18
211
20
20
20
21
22
23
23
23
24
24
26
26
Turning off the built-in speakers ..................
Selecting the optical audio output format ...........
Using the Locks menu .............................
Entering the PIN code ..........................
If you canuot remember your PIN code .............
(banging your PIN code ........................
Blocking TV programs and movies
by rating (V-Chip) ..........................
Blocking channels .............................
Unlocking programs temporarily ..................
Using the iuput lock feature ......................
Using the control panel lock feature ...............
Setting the sleep timer ..............................
Displaying TV setting information on-screeu using
RECALL ....................................
34
34
35
35
35
35
Understanding
Understanding
40
40
the auto power off li:attlre ..............
the last mode memory feature ...........
Chapter6: Usingthe lV's advancedfeatures.............
16
Chapter
33
34
36
37
38
38
39
39
40
41
Using the adv:mced picture settings li:atures ............
Using dyuamic contrast .........................
Using CableClear®/DNR
(digital noise reduction) ....
Using MPEG noise reduction .....................
Selecting the color temperature ...................
Selecting the lamp mode ........................
Using the Game Mode feature ....................
Using the advauced audio settings features .............
Using the SRS WOW I_1surround sound feature ......
41
41
41
41
42
42
43
43
43
7: Troubleshooting
.........................
General troubleshooting
............................
LED iudicatious ..................................
44
44
46
Chapter 8: Appendix..............................
47
Lamp unit replacement and care ......................
Replacing the lamp unit
(User-replaceable
component) .................
47
When to replace the lamp uuit ....................
How to replace the lamp unit .....................
Disposing of the used lamp unit ...................
Specifications
....................................
Lfinited United States Warranty
li_)r[)LP _x_Television Models ....................
47
48
49
50
Limited Canada Warranty
for DLP Ix( Televisiou
Models
....................
47
51
52
26
Index........................................
54
26
Switching between two channels using SurfLock jxl ...
Selecting the picture size ...........................
Scrolling the TheaterWide ® picture (TheaterWide 2
26
27
and 3 only) ...................................
Using the auto aspect ratio li:ature ....................
Selecting the ciuema mode
(480i signals only) .............................
Adjusting the picture ...............................
Selecting the picture mode .......................
Adjusting the picture quality .....................
Using the closed caption mode .......................
Closed Captiou Advanced .......................
Digital closed captions ..........................
28
29
Adjusting the audio ................................
Muting the sound ..............................
Usiug the digital audio selector ...................
Selecting stereo/SAP broadcasts ..................
32
32
32
33
29
30
30
30
31
31
32
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 4 Tlmrsdav
Februa W 23 2006
2:49 PM
Carefully read the important safety, installation,
service information in the separate Installation
Keep this manual tor future reference.
NOTICE OF POSSIBLE TV STAND INSTABILITY
DANGER: RISK OF SERIOUS PERSONAL
INJURY OR DEATH!
Use this TV only with
the TOSHIBA TV stand listed in the
"Specifications"
section of this manual. Use with other
stands may result in instability, causing possible injury or
death.
2
Observe
TV:
the following
when choosing
• Read the separate Installation
• Two HI)MI TM digital, high-definition multimedia
interfaces (ir__ Installation Guide).
• Two sets of ColorStream® HD high-resolution component
video inputs (Ir_r"Installation GuMe).
• SRS WOW TM (Ir_> page 43), audio technologies.
• Digital Audio Out optical audio connection with Dolby _
Digital optical output format (ir_> page 34; also see
Installation Guide).
• CableClear ® DNR digital picture noise reduction
(tr_> page 41 ).
Overviewof stepsfor installing,
settingup, andusingyournew TV
Follow these steps to set up your TV and begin using its many
exciting features.
TM
projection
where light does not reflect
3
Do not plug in any power cords until AFTER you have
connected all cables and devices to your TV.
4
BEFORE connecting cables or devices to the TV, learn
the functions of the TV's connections and controls
(Ir_ pages 5-6).
5
Connect your other electronic device(s) to the TV
(1>;€hlstallation Guide).
6
7
Install the batteries in the remote control (Irgvpage 7).
8
Program the remote control to operate your other
device(s) (Irgv pages 9-13).
9
AFTER connecting all cables and devices, plug in the
power cords for your TV and other devices.
10
After you plug in the TV power cord, the yellow LED
ion the TV front ) will blink 3 times. Wait several
seconds until the yellow LED stops blinking and then
press _E, on the TV or remote control.
See "LED indications" (ir_ page 46).
11
See "Menu layout and navigation" for a quick overview of
navigating the TV's menu system (r:_ page 14).
12
Program channels into the TV's channel memory
(__ page 17).
13
For details on using the TV's features, see Chapters 5
and 6.
14
For help, refer to the Troubleshooting Guide
(Irw Chapter 7).
15
16
For lamp unit replacement instructions, see Chapter 8.
17
Enjoy your new TV!
"Voice announce" feature
When certain non-standard conditions occur, the LEDs on
the TV will blink and the TV will play a recorded
"voice announcement" describing the condition (see the
LED indication table on page 46 for the specific conditions
that include a voice announcement).
To repeat the voice announcement and hear additional
information, press the MENU button on the TV while the
LEDs are blinking.
Guide.
• Place the TV far enough from walls and other objects to
allow proper ventilation. Inadequate ventilation may
cause overheating,
which will damage the TV. THIS
TYPE OF DAMAGE IS NOT COVERED
UNDER
THE TOSHIBA WARRANTY.
Featuresof yournewTV
• Integrated digital tuning (8VSB ATSC and QAM)
eliminates the need for a separate digital converter set-top
box (in most cases).
• Digital CableCARD TM slot for viewing encrypted digital
Cable TV programs (ir_ hlstallation Guide).
for the
• Place the TV on the applicable optional TV stand listed
in the "Specifications"
section (if available for this TV
model) or on a sturdy, level, stable surface that can
safely support the size and weight of the unit.
• Place the TV in a location
on the screen.
The following are just a few of the many exciting features of
your new Toshiba widescreen, integrated HD, DLP TM
projection TV:
a location
• Read "Important notes about your DLP
TV" (ir_ page 2).
CAUTION:This
television is for use only with the Toshiba
stand indicated below. Use with other carts or stands is
capable of resulting in instability, causing possible injury.
Television
Stand Model
50HM66
ST5066
56HM66
ST5666
care, and
Guide.
See "Learning about the remote control" (rW page 8) for
an overview of the buttons on the remote control.
For technical specifications and warranty information, see
Chapter 8.
HM66 (E/F) Web 213:276
HM66
ENbook
Page 5 Tlmrsdav
Februa W 23 2006
2:49 PM
TVfront andside panelcontrolsandconnections
Frontof TV
Rightsideof TV
LE_
[LAMP POWER
]
2
9
Controlpanel
1
Remote sensor (behind the screen) -- Point the remote
control toward this area of the TV screen. See "Remote
control effective range" (ire'vpage 7).
2
Blue, Yellow and Green/Red LEDs
*MENU (ENTER) -- Press to access the menu system
(Ir_>"pages 14-15). When a menu is on-screen, the MENU
button on the TV's side control panel functions as the
Enter button.
ARROWS AV'4 • -- When a menu is on-screen, these
buttons function as up/down/left/right menu navigation
buttons.
See "LED indications" (ir_ page 46) for additional
information.
3
POWER -- Press to turn tile TV on and oft:
If the TV stops responding to the controls on the remote
control or TV control panel and you cannot turn offthe
TV, press and hold the POWER button on the TV control
panel for 5 or more seconds to reset the TV.
Sidepanel
9
EXIT -- Press to instantly close an on-screen menu.
10
VIDEO-2 IN -- The side panel A/V connections are
referred to as "VIDEO 2" and include standard A/V
connections plus optional S-video.
CHANNEL ^ v -- When no menu is on-screen, these
buttons change the channel (programmed channels only;
_r_'_page 17). When a menu is on-screen, these buttons
function as up/down menu navigation buttons.
VOLUME + - -- When no menu is on-screen, these
buttons adjust the volume level. When a menu is onscreen, these buttons function as left/right menu
navigation buttons.
INPUT -- Repeatedly press to change the source
you are viewing (ANT 1, VIDEO 1, VIDEO 2,
ColorStream HD-1, ColorStream HD-2, HDMI 1,
HDMI 2, ANT 2).
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 6 Thursday
Februal T 23 2006
2:49 PM
t
TVbackpanel connections
For an explanation
of cable types and connections,
see the Installation
Guide.
8
2
VIDEO 1 IN -- Standard (composite) video and standard
audio inputs plus optional S-video inputs for connecting
devices with composite video or S-video output.
ANT 1 and ANT 2 -- Two inputs that support analog
(NTSC) and digital (ATSC) off-air antenna signals and
analog and digital (QAM) Cable TV signals.
Note: Standard (composite) video and S-video cables
carry only video information; separate audio cables are
required for a complete connection.
Note: If you have an antenna only, connect it to ANT I. tf
you have both cable TV and an antenna, connect the
cable TV to ANT 1 and the antenna to ANT2
ColorStream ® HD-1 and ColorStream ® HD-2Two sets of ColorStream ® high-defnition component
video inputs (with standard stereo audio inputs) for
connecting devices with component video output, such as
a Toshiba DVD player with ColorStream ®.
HDMI TM 1 and 2 IN -- Two High-Definition
Multimedia
Interface inputs receive digital audio and uncompressed
digital video from an HDMI device or uncompressed
digital video from a DVI device. Also see item 2.
Note: Component video cables carry only video
information; separate audio cables are required for a
complete connection.
ColorStream ® HD-1 and ColorStream ® HD-2
Audio IN -- ColorStream
HD-I/2
are shared with HDMI 1/2 analog
and their use can be configured in
(ir_v "Setting the ColorStream
HD
3
9
audio input terminals
audio input terminals,
the Setup menu
audio mode" page 20).
Variable Audio OUT-- Standard analog audio outputs
for connecting an analog amplifier with external speakers.
4
A/V OUTStandard
outputs for connecting
5
IR OUT -- For controlling infiared remote-controlled
devices through the TV. You can connect up to two
devices with an IR blaster cable, and then control the
devices using the TV's IR pass-through features.
composite video and analog audio
a VCR for editing and dubbing.
Digital Audio OUT -- Optical audio output in Dolby
Digital or PCM (pulse-code modulation)
format for
connecting an external Dolby Digital decoder, amplifier,
A/V receiver, or home theater system with optical audio
input.
CableCARD
TM
slot -- For use with a digital security
card and digital cable TV selwice (provided by your local
cable operator) to view encrypted digital programming
(try> page 20).
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
CableCARD is a trademark of Cable Television Laboratories, Inc.
HM66 (E/F) Web 213:276
HM66
ENbook
Page 7 Thursday
Februal T 23 2006
2:49 PM
t
Preparingthe remotecontrol
for use
° Always remove batteries from remote control if they are
dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid from
leaking into the battery compartment.
Your TV remote control can operate your TV and many other
devices such as cable converter boxes, satellite receivers,
VCRs, DVD players, and HTIBs (home theater in a box), even
if they are different brands.
Remotecontroleffective range
If you have a Toshiba device:
Your TV remote control is preprogrammed to operate most
Toshiba devices (ir_vpage 11).
If you have a non-Toshiba
device or a Toshiba device
that the remote control is not preprogrammed
to
operate:
You can program tile TV remote control so it will operate tile
other device (Ire'r"pages 9-13).
Installingthe remotecontrol
batteries
1
For optimum performance,
aim the remote control directly
the TV and make sure there is no obstruction between the
remote control and the TV.
at
Point remote control
toward remote sensor
on front of TV.
16.4 ft (5m)
Remove the battery cover flom the back of the remote
control.
Squeeze
)lift
cover. tab and l|_]l
_
2
Install two "AAA" size batteries, making sure to match
the + and- signs on the batteries to the signs on the battery
compartment.
3
Reinsell the battery
tab snaps.
Caution:
cover in the remote control
until the
Never throw batteries into a fire.
Notes:
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
° Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in
accordance with applicable laws and regulations.
° tf the remote control does not operate correctly, or if the
operating range becomes reduced, replace batteries with
new ones.
° When necessary to replace batteries in the remote control,
always replace both batteries with new ones. Never mix
battery types or use new and used batteries in combination.
t
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 8 Tlmrsdav
Februa W 23 2006
2:49 PM
t
Learningaboutthe remotecontrol
1
Tile buttons used for operating tile TV only are described here.
For a complete list of the remote control's functions, see the
remote control functional key chart (_'_ page 10).
]l|
7
10
11
-
POWER
2
FREEZE fieezes the picture. Press again to restore the
moving picture.
3
SLEEP accesses the sleep timer (_'r page 39).
4
PIC SIZE cycles through the five pictures sizes: Natural,
TheaterWide
1/2/3, and Full (t_> page 27).
5
Channel
channels.
(tr_'rpage
(Ir,'r"page
6
INPUT selects the video input source (_'r page 23).
7
CH AV cycles through programmed channels when no
menu is on-screen (r,'r"page 17) and functions as page up/
down when a menu is on-screen.
8
VOL + - adjusts the volume level.
9
HOME (lql')accesses the home function of the Channel
Browser TM feature (ir_> page 26).
+10
6
-
Note: TheQuick RestartTM setting will affect the amount of
time it takes for thepicture to appear when you turn on the
TV(ri_ page 20).
5
III
POWER turns tile TV on and off. Press O to turn on tile
TV. The blue LED indicator on the TV front will be
illuminated. Press P_ERagain to turn off the TV.
Numbers (0-9, -/100) directly tune
The "-" button is used to tune digital channels
26) or to display the favorite channel list
19).
10 RECALL displays TV setting intk)rmation on-screen
(ir_ypage 40).
14
-15
17
-18
11 CH RTN returns to the last viewed channel (Ir_>"page 26).
12 MUTE reduces or turns off the sound (ir_ page 32).
1,7
• / a;i• While watching TV, these buttons open the
Channel Browser TM banner and tune to the pmvious/next
channel in the channel history (ir_
> page 24). (Also see
"Arrow buttons".)
14 Arrow buttons (AV• •) When a menu is on-screen,
these buttons select or adjust programming menus. (Also
see '_ • / _4 •.)
15 FAV AV tunes to the next higher/lower favorite channel
(Ire'r"page 19).
16 ENTER activates highlighted items in the main menu
system.
17 MENU accesses the main TV menu system (tr_'rpages 14
and 15).
18 EXIT closes on-screen menus.
19 MODE SELECT Switch switches between TV,
CABLE/SAT, DVD, and VCR modes (_'r page 9). Set to
"TV" to control the TV.
Note: The error message "NO T A VAILABLE" may appear if
you press a key for a function that is not available.
HM66 (E/F) Web 213:276
HM66
ENbook
Page 9 Tlmrsdav
Februa W 23 2006
2:49 PM
t
Usingthe remotecontrolto control
yourother devices
If you have a non-Toshiba device or a Toshiba device that the
remote control is not preprogrammed to operate, you must first
program the remote control to recognize the device (if you
have not aheady done so) (Ire'r"pages 11-13).
To use your TV remote
control
to operate
a:
1
POWER Turns the selected device on and off
2
Channel Numbers (0-9) Press to directly access
channels (as opposed to _ _,").
3
+10 Press to directly access DVD chapters higher than 10.
4
CH ,&•
• selects the next higher channel;
• selects the next lower channel (for channels
programmed into memo U only).
8
GUIDE Displays channel guide.
• Cable converter box or satellite receiver, set the MODE
SELECT Switch to CABLE/SAT.
6
INFO Displays TV status information on-screen.
• VCR, set the MODE SELECT Switch to VCR
7
• DVD player or HTIB, set the MODE SELECT Switch to
DVD.
••'_ • Press to navigate DVD menus (may not work on
some DVD players).
8
ENTER Required by some satellite receivers and DVD
players.
9
DVD CLEAR Press to reset the title and chapter number.
Note: Even after the TV remote control is programmed, it may
not operate certain features on your other device, tf this
happens and you wish to use those features, you will need to
use the device's original remote control.
10 PLAY Begins playback of a tape or DVD.
11 PAUSE Press during play or record mode to pause the
picture; press again to restart.
Point the remote control
directly at the device.
12 STOP Stops the tape or DVD.
13 SKIP _
CD : Q
Skips forward to locate later DVD chapters.
14 FF Fast-forwards the tape or DVD. (Press during play
mode to view the picture moving rapidly forward.)
2 QQCD
Q CD(:i:)
a--
15 SKIP _ Skips back to beginning of current DVD chapter
or locates previous chapters.
16 REW Rewinds/reverses the tape or DVD. (Press during
play mode to view the picture moving rapidly backward.)
17 TV/VCR To view one program while recording another,
press to select TV mode.
18 REC Starts tape recording.
19 TOP MENU Accesses a DVD's top menu.
20
4 4
lit _AUS_STEp
>---.-.._
stop
I1|
4 _'J
13
1"'7 /c 111
...................
c-<o _11|""19
SET UP Accesses a DVD's setup menu.
21 MODE SELECT Switch Set to "TV" to control the TV;
"CABLE/SAT" to control a cable converter box or
satellite receiver; "DVD" to control a DVD player or
HTIB; "VCR" to control a VCR.
181___1 -- 11" J!i20
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 10 Thursday
February 23. 2006 2:49 PM
t
Remote Control functional key chart
Notes:
• "---" = key does not send a signal in that remote control mode.
° _TV
= key will affect the TV, even when the remote control is not in the "TV" device mode.
Power
Power
Power
Power
Power
TV
TV
TV
TV
TV
TV
TV
TV
Digit 1-9
Digit 1-9
Digit 1-9
Digit 1-9
Digit 1-9
Digit 0
Digit 0
Digit 0
Digit 0
100
Digit 0
+10
Display
TV
Sleep timer
TV/Video select
- (sub channel)
RECALL
TV
- (sub CH)
TV
Previous channel
lnfo
Menu/DVD Menu
Menu
DVD Menu
Menu select/
FAV up/down
Menu select/
Channel Browser
Menu
up/down
Menu up/down
TM
Menu left
Menu left
Menu select/
Channel Browser
TM
Menu right
Menu right
Select Enter
Enter
Enter
Exit
Exit
TV
Volume up/down
Channel
up/down
Picture size
Channel
up/down
TV
Sound mute
TV
TV
Channel
up/down
TV
TV
DVD Clear
TV
Channel
upAtown
TV
TV
TV
TV
TV
Fast FWD
Fast FWD
Pause
Pause
Play
Rewind
Play
Rewind
Stop
TV
Stop
TV
SAT Guide
Channel Browser
Home
Freeze picture
TM
TV
TV
Skip REV
Skip FWD
TV/VCR
Record (2 click)
DVD Setup
Top Menu
10
HM66 (E/F) Web 213:276
HM66
ENbook
Page 11 Thursday
February 23. 2006 2:49 PM
t
Programmingthe remote control to
control your other devices
Your Toshiba TV remote control is preprogrammed to operate
most Toshiba devices. To program your TV remote control to
operate a non-Toshiba device (or a Toshiba device that it is not
preprogrammed to operate), follow the steps below. For details
on using the remote control to operate the device, see page 9.
In tile remote control code table (ir_ page 12), find tile
code for your device. If more than one code is listed, try
each one separately until you find one that works.
2
Set the MODE SELECT Switch to the type of device you
are programming the remote control to operate -CABLE/SAT (for a cable converter box or satellite
receiver), DVD (for a DVD player or HTIB [home theater
in a boxl), or VCR (for a VCR or TV/VCR combo).
3
While holding down ,E_LL,press the Channel Number
buttons to enter the 3-digit code for your device.
4
To test the code, turn on the device, point the remote
control at it, and press ,_E, See notes below,
• If the correct code was entered,
the device will turn off,
• If the device does not respond,
another code,
repeat steps 1-4 using
• If the device does not respond to another code, you will
need to use the remote control that came with the
device,
5
Remember to set the MODE
to control the TV,
6
For future reference,
SELECT
Switch back to TV
write down the code(s)
you used:
Notes:
• tn addition to POWER, confirm thatallnecessarykeys
on the
TVremote control operate your device, tf some keys are not
operational, repeat the device code setup using another
code (if other codes are listed for your device). If, after trying
all listed codes, the necessary keys do not operate your
device, use the device's original remote control.
• Every time you change the batteries, you will need to
reprogram the remote control.
• Some newer VCRs respond to either of two codes. These
VCRs have a switch labeled "VCR1/VCR2." tf your VCR has
this kind of switch and does not respond to the codes for
your VCR brand, set the switch to the other position ("VCR1"
or "VCR2") and reprogram the remote control.
11
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 12 Thursday
Februarv 23. 2006 2:49 PM
t
Remotecontrolcodes
In some cases you may not be able to
operate your device with the TV
remote control. Your other device may
use a code that is not recognized by the
TV remote control. If this happens, use
the device's remote control.
Archer
Cableview
Century
Citizen
Contec
Diamond
Eagle
GE
Gemini
General Instruments
Hamlin
Hitachi
Jasco
Jerrold
Magnavox
Memorex
Multi Canal
Novavision
P:m:tsonic
Philco
Philips
Pioneer
Proscau
Radio Shack
RCA
Realistic
Recoton
Samsung
Scientific Atlanta
Sears
Signature
Signature 2000
Sprucer
Starcom
Stargate
Sylvania
TeleView
Texscan
Tocom
13.S. Electronics
1Jnited Cable
13niversal
Wards
096
071. 082.
091. 096
Uniden
061. 062.
084. 087.
I)96. 098
I)65. 092.
064. 094
092
090. 092.
083. 085.
093. 098
093
1)91
061,062
069,070,
062. 089.
093
062.095.
097
062.069.
086. 089.
{)72. 096
{)91. 092.
090
101
081. 083.
087
063. 082.
091. 092.
{)66. 067.
072. 073.
091. 092
076.077
061. 062
I)92.097.
I)64. 081
065
11)2
077.090
063. 078.
088. 098.
095
062
096
081. 085
069. 082.
103. 104
068. 070.
074.075.
Alphast:u"
Chaparral
DISH Network
097.099
097
086.088.
094
096
104
Zenith
085
099
079.080.
101. 105
038.059
034
057
020. 040. I)44. 046.
050. 1)53
018.04 I. 051
057
027
008. 009. 013
010. 011.012. 022.
023.03 I. 1}49
033
033
Classic
Daewoo
Denon
Emerson
Fisher
Funai
GE
Go Video
G PX
Hitachi
019
048
027
017.1)57
029
060
058
036. 052
015.1)42
008. 009. 013
022. 023. 030
{}{)8.01)9.013. 016
030
1)59
014. 055
057
025. 026. 037. 054
024
1}{)0.001. (}{)2.003.
I}{)4,005, {}{}6,007,
020, 031,056
021. 028, 030. 032.
035. {)39. {M3. 045.
047,058
027
JVC
Action
GE
Goldstar
Panasonic
Precision
Quasar
Realistic
Sony
Toshiba
Totevision
Zenith
Go Video
087.096.
Kenwood
Konka
Magnavox
Memorex
Mintek
NAD
Nakamichi
Norcent
Onkyo
Oritron
Pauasonic
Philips
Pioneer
Proscan
Qwestar
RCA
Sampo
Samsung
Sausui
Sauyo
Shm'p
Sherwood
Sony
TV/VCR Combo
078
059, 062
065
065
078
065
079
074
057
009. 010. 065
065
DVD/VCRCombo
069.090
095. 100
090
100
{)71. 084. 085
087.096. 098
082
065. 092. 097.099.
102. 103
1)96
Satellite receiver
Echostar
Express Vu
Fujitsu
GE
General Instruments
Hitachi
Hughes
Hughes Network
Systems
lntersat
Janeil
JVC
Kenwood
Magnavox
Optimus
Pansat
Primestar
Proscan
Radio Shack
RCA
Realistic
Samsung
Sony
Star Choice
Star Trak
STS
Toshiba
Cable converter box
ABC
[)rake
JVC
RCA
Samsung
Sanyo
Zenith
DVD={}87
VCR=081
DVD=088
VCR=082
DVD=089
VCR=083
DVD=090
VCR=084
DVD=091
VCR=085
DVD=092
VCR=086
DVDplayer
Aiwa
Apex
BOSE
Broksonic
Clarion
{}{t6,{}15
016, 017
097
0l 8
019
Sslvania
Teac
Technics
Techwood
Toshiba
Yamaha
Zenith
020
021
022.
026.
028
027
001.
087
031
005.
035
003.
088
037
008.
004.
039
040
026
041
043
044
058
010.
048.
004.
052.
001.
057.
001.
060
061.
073
063,
064,
074
01 l,
068,
023. 024. 025
027
029. 030
032. 033. {)34.
007. 036. 042.
{)09
038
045.
049,
051
053.
056
058
002.
046. 047.
050
054. 055
059. 089
062. 086. 090
091
067
012, 065,066,
069, 070
027
071
072
075
000. 013. 076. 077.
078
079. 080. 081
014. 082. 092
Portable DVDplayer
Aiwa
Audiox ox
Pauasonic
RCA
093
1}94,{)95
024. 096. 099
098
VCR
Admiral
Aiko
Aiwa
Akai
Audiovox
Bell & Howell
Broksonic
Calix
Carver
CCE
Citizen
Colortyme
Craig
049
019
018
003. 004.
039. 058.
010
007.068
008, 017
o I0
026
019
1}{}9,010,
013. 014.
057. 073
005
009. 010.
065. 079
037. 038.
069
011, 012,
015. 019.
016. 061.
12
HM66 (E/F) Web 213:276
HM66
ENbook
Page 13 Thursday
February 23. 2006 2:49 PM
t
Curtis Mathes
Daewuo
Daytron
Denun
Dimensia
Electrohome
Emerson
Fisher
Fuji
Funai
Garrard
GE
Go Vide()
Guldstar
Gradiente
Harman Kardun
Hitachi
JBL
JC Penuey
Jensen
J VC
Kenwood
Kodak
LG
Lloyds
Logik
LXI
Magnasonic
Magnavox
Marantz
Memorex
MGA
MGN
Minolta
Mitsubishi
Montgomery Ward
Motorola
MTC
Multitech
NEC
Nikko
Noblex
Optimus
Optonica
Orion
001, I}{)5, 009, 012,
014, 040, 048,053,
056, 057
0l 1,013, 015, 017,
018, 019, 057,078
{)78
063
001,048
010, 020, (165
003, (108, 010, 011,
017, 018, 020, 028,
039, (154, 057,062,
065,068, 072
007, 016, 021, (122,
023, 057, 064, 068,
070, 071,079
004, 041
018,073
018
001,002, 009,040,
042,048, 056
056, 059, (161,081
005, 010, 014, (154,
056,065,067
018, 065
0(./5
(124, 025, 035,037,
042, (163, I)71),080
076
0{)5, {}{)6,007, (108,
0(.19,010, 023,024,
025, 026, 035, (156,
061,063, {165
024,025, 037
{){)5,006, {)t.17,014,
037, 043,062, (163,
068, 082
0(.15,(106, (I{)7,012,
014, (137, 043,053,
068, 07 I
010
010
Panasonic
{)53,073,079
{)61
01(.1
061, (165, {)78
{)26,027, 034, 044,
057,061,072
0(.15,(106, 0{)7, 012,
014, (126, {)53,067
007,009, 01{1,016,
018, 034, 049,063,
065, 066, 068,075,
079
020, 028, 039
056
024, (125, 035,063
(120, 024, 025,028,
039,043,065
Sharp
049
049
009, (146, 06 I
{)09, 012, 018
{)05,006, 0(.17,012,
014, 037, 043, (153,
054, 067, 070
010
009
(I] 0, 049, 065
031
054,057, 062, (165,
068, 072
Pentax
Pentex Research
Philco
Philips
Pioneer
Porthmd
Proscan
Proton
Quasar
Radiu Shack
Radiu Shack/Realistic
Radix
RCA
Realistic
Ricuh
RUUCO
Samsung
Sansui
Sanyo
Scott
Sears
Shiutom
Signature
Signature 2{}{)0
Singer
Suny
STS
Sylvania
Symphonic
Taudy
Tashiko
Tatung
Teac
Technics
Teknika
Toshiba
Totevisiuu
Unitec
Unitech
Vectur Research
Vide(( Concepts
036, 045,046, 057,
061,072, 079
012, 024, 025, (135,
{,'42, 053,063
014
026, 027, 063
026, 031,044, 057
{}{}6,024, {}43,055
012, 013,015
{}{}
1, 002, {_8
061
045
010, 031,065
007,009, 01(.1,016,
018, 020, 021,022,
031,049
010
{}{)1,002, {}{}3,009,
024, 025,029, 035,
{}40,042, 045, 048,
055, 056, 063, 07 I,
083
007,009, 010, 011,
016, 018, 020, 021,
022, 031, {}49,051,
056, 060, 065, 075,
079
O47
034
{}{}9,011, 038, 056,
{}73,084
{}{}6,037, 043, 061
{}{t7,009, 016, 054,
064, {t68, 071,075,
079, 085
008, 011,017, 028,
030, 057, 065, 072
{}{}7,010, 016, 021,
022, 023, {)24, 025,
035, {)53, {)57, 063,
064, 065,068, 071,
{}75,079
013, 020, 031,049,
051,060, 066
{}{}4,025,032, {161
{)49
075
{_7, 06 l
I}{}4,032, 033, 041,
052, 058, 070, 074,
076, 077, 080
O35
018, 026, 027, 028,
044, 072
018, 051,053, (173,
079
{}{}7
o 1o
037
018, 029, 037
036
010, 018, 065
{}{10,011, 021, 023,
024, 028, 030, 039,
057, 074, 078, 079
009, 010, 065
073
009
005,006, 011,012,
053
005, 006, 011, 012,
039, 053
Wards
White Westinghouse
XR- 101}{)
Yamaha
Zenith
009, 010,
Ol 8, 020,
031,035,
056, 057,
066, 079
073
018
005, 006,
037, 053
004, 032,
(147, 069,
Ol 1,016,
024, {t25,
049, 051,
060, 065,
(I(17,014,
(134, 041,
086
HTIB
Lasunic
Panasunic
Venturer
083
084
085
13
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 14 Thursday
February 23. 2006 2:49 PM
t
Main menulayout
Tile illustrations below and on tile next page provide a quick overview of your TV's menu system.
To open the main menus (illustrated below), pie..
" ss MENU
O on the remote control or TV control panel.
Applications
Channel
Browser
---* [Launches
Digital CC/Audio
CabIeCARD
Video
Picture
Theater
Audio
Audio
Preferences
Locks
Settings
Audio
Settings
Setup
---* [Advanced
_
[Theater Settings
_
[Audio Settings
---* [Advanced
_
Channels
Settings
edit window]
edit windowl
window]
Audio
Settings
window]
[Audio Setup window]
---* [Favorite
Channels
edit window]
Mode
---* Off/CCI/CC2/CC3/CC4/TI/T2/T3/T4
Closed Caption
Advanced
---* [Closed
Caption
Input Labeling
_
[Input Labeling
Menu Language
_
English
Channel
_
[Channel
_
Off/On
Browser Setup
Enable Rating
Channels
(This option is not awfilable,
edit window]
Picture
Closed Caption
Edit Rating
Setup
---* [Picture Settings
Settings
Settings
Favorite
BrowsegrMl
Dynamic list of items provided by Cable company.
(This option is not available ifa CableCARD
TM is not inserted.)
TM
Picture
Advanced
Audio
Selector
Settings
Advanced
the Channel
[Launches the ATSC Digital CC Selectorl
if you are not on a digital channel).
Blocking
Limits
Block
Advanced
window]
edit window]
/ Franqais
Browser
/ EspalSol
Setup window]
---* [Edit Rating Limits edit window]
_
[Channels
Input Lock
Front Panel Lock
_
_
Off/Video/Video+
Off/On
New PIN Code
_
[New PIN Code entry windowl
Installation
Sleep Timer
_
_
[Opens the Installation
menu (ir_ page 15)1
[Sleep Timer edit windowl
ColorStream
HDMI
1 Audio
ColorStream
HDM[
HDI Audio
HD2 Audio
2 Audio
Quick Restart
Block edit window]
---* No/Yes
---* Auto / Digital / Analog
_
No/Yes
_
Auto / Digital / Analog
---* Off/On
14
HM66 (E/F) Web 213:276
HM66
ENbook
Page 15 Thursday
February 23. 2006 2:49 PM
t
Setup/Installationmenulayout
•
S
SS MENU
To open the Installation menu (illustrated
below), press
o on the remote control or TV control panel, open tile Setup menu,
select Installation, and press @.
SS MENU
Pre,_'s©.
Terrestrial
Setup menu,
Open tile
and then open
tile
Installation
sub-menu.
Input Configuration
_
Channel Program
[Input Configuration window[
ANTI _ [Scans for new channels on desired
Antenna]
ANT2 _
Antenna]
[Scans for new channels on desired
Channel Add/Delete
_
[Channel Add / Delete Window[
Signal Meter
_
[Signal Meter Window[
System Information
_
[Opens tile System Information windowl
System Status
Navigatingthe menusystem
Note: The menu background may sometimes appear black,
depending on the signal the TV is receiving.
This is not a sign of malfunction.
You can use tile buttons on tile remote control or TV control
panel to access and navigate your TV's on-screen menu
system.
• Press M_Uto open the menu system.
• When a menu is open, use tile up/down/left/right arrow
buttons (AV._I_) on tile remote control or TV control panel
to move in the corresponding direction in the menu.
• Press @ to save your menu settings or select a highlighted
item. (A highlighted menu item appears in a different color
in the menu.)
• All menus close automatically if you do not make a selection
within 60 seconds, except the signal meter menu, which
closes automatically after about 5 minutes.
• To close a menu instantly, press EX,¢_.
15
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 16 Thursday
February 23. 2006 2:49 PM
Selectingthe menulanguage
You can choose flom three different languages (English,
French and Spanish) for the on-screen display of menus and
messages.
To select the menu language:
Configuringthe antennainput
sourcesfor the ANT1 andANT2
terminals
To configure
1
Press M_uand open the Preferences
2
Highlight Menu Language
3
Press • or • to select your preferred menu language and
press @.
menu.
and press •.
the ANT 1 and ANT 2 input sources:
1
Press M_uand open tile Setup menu.
2
Highlight Installation and press @. (A new set of
Installation
menu icons will appear on-screen, as shown
in step 3 below.)
Sleep Timer
HDMI
•
....
4
ENTER• •
CH_r_:
1 Audio
• _ • Etl_R
••
CH_T_:•
EXIT
EXIT
Press EXIT
co to close tile Preferences menu.
3
Open tile Terrestrial menu, highlight Input
Configuration,
and press @.
_•
•
!!!ChannelProgram
i!il
iiigi;,_;i M;i;;
iiiii
EN_R •
_H_rN:•
Exrr
4
Press • or • to highlight ANT 1, and press • or • to
select the input source (Cable or Antenna) for the
ANT 1 input on the TV.
5
Press • to highlight Antenna 2 in and then • or • to select
the input source (Cable or Antenna) tor the ANT 2
input on the TV, if applicable. It"you have not connected
anything to the ANT 2 input, skip this step.
Antenna
6
2 In
Antenna
To save your new settings, highlight Done and press @.
To revert to your original settings, highlight Cancel and
press @.
16
HM66 (E/F) Web 213:276
HM66
ENbook
Page 17 Thursday
February 23. 2006 2:49 PM
t
Programmingchannelsintothe
TV'schannelmemory
3
Highlight Installation and press @. (A new set of
Installation menu icons will appear on-screen, as shown
in step 4.)
When you press _ or _," on the remote control or TV control
panel, your TV will stop only on the channels you program into
the TV's channel memory.
Follow the steps below to program channels into the TV's
channel memory.
Programmingchannels automatically
Your TV can automatically detect all active channels in your
area and store them in its memory. Alter the channels are
programmed automatically, you can manually add or erase
individual channels.
.
4
• ENTER • •
CH_I =•
EXIT
Open the Terrestrial menu, MgMight
Program, and press ,_.
Channel
Notes:
• You must configure the antenna input sources before
programming channels (_. page 16).
° If the input signal type is set to Cable for an antenna input,
the automatic channel programming process erases
channels that were previously programmed into the TV's
memory.
° tf the input signal type is set to Antenna, the automatic
channel programming process does NOT erase channels
that were previously programmed into the TV's memory, but
adds newly found channels to the existing set of
programmed channels. To remove a channel from the
memory, you must manually delete it.
5
° To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the
remote control.
° Programming channels for an antenna input configured for
Cable will take substantially longer than for an antenna input
configured for Antenna. This is normal; however, once
channel programming is completed, you should not ha ve to
repeat the programming process again unless your Cable
TV service lineup changes significantly.
° If you have a CableCARD TM inserted, channelprogramming
for ANT I is disabled because the CableCARD TM
automatically loads the Cable channel list into the TV's
channel memory. See Installation Guide for details on
CableCARD TM.
To program
channels
automatically:
1
Make sure you have configured the antenna input sources
(_'r page 16).
2
Press Mff_u
and open tile Setup
menu.
6
Highlight ANT 1 or ANT 2, depending on which antenna
input you want to program channels for, and then press @
to start automatic channel programming.
The TV will automatically cycle through all the channels
for the antenna input you selected, and store all active
channels in the channel memory. While the TV is cycling
through the channels, the message "Scanning channels,
please wait" appears (as shown above).
To cancel channel programming,
.
"
either
press EXIT
O or
highlight Abort in the on-screen display and press @.
When channel programming is done, press _ or _," to
view the programmed channels.
Manually adding and deleting channels in
the channel memory
After automatically
programming
channels into the channel
memory, you can manually add or delete individual channels.
To add or delete channels
in the channel
memory:
1
Press Mff_u
and open the Setup menu.
2
Highlight Installation and press @. (A new set of
Installation
menu icons will appear on-screen, as shown
in step 3.)
(con tin ued)
17
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 18 Thursday
Februar,¢ 23. 2006 2:49 PM
t
Open tile Terrestrial menu, highlight Channel Add/
Delete, and then press@.
To remove all channels from the channel memory:
Highlight Reset and press @, and then highlight Done and
press @.
Notes:
• This action applies to the current antenna input only. To
delete/add channels on the other input, highlight the input
you want (ANTI, or ANT 2) and press @.
° ThisactioncannotbecancelledunlessyouhighlightCanee!
and press @ before saving your changes.
•
4
.
•
_N_R • •
CH_rtl=•
Exrr
The illustration below left shows channels programmed
for the ANT 1 antenna input. To view the list of channels
programmed
for the ANT 2 antenna input, press AV to
highlight ANT 2 and press ,@.
To add a channel to the channel memory:
Highlight tile unchecked box next to tile channel number you
want to add, and then press @ to check the box.
To manually
channel:
add digital
subchannels
on a physical
Use the Channel Numbers and the Dash ((_)) on the remote
control to enter the channel number (tbr example, 56-1 ).
If the channel is found, the number will be added to the list and
the box will be checked.
If the channel is not found, a message will appear.
To remove a channel from the channel memory:
Highlight the checked box next to the channel number you
want to remove, and then press @ to uncheck tile box.
Programming
yourfavorite
channels
You can program up
two Favorite Channel
input, and nine from
through your fiworite
you do not normally
to 18 channels as fiwofite channels into
lists (nine channels from the ANT 1
the ANT 2 input). You can then scan
channels only, skipping other channels
watch.
To add and delete channels
lists:
in the Favorite
Channels
1
Press Mff_uand open tile Preferences
2
Highlight
3
Use AV to select either ANT 1, or ANT 2, and press ,@.
4
Highlight
Favorite
Channels
menu.
and press,@.
Edit and press,@.
To save your new settings:
Highlight Done and press @.
To revert to your original settings:
Highlight Cancel and press @ before saving.
ii_input Labeling
,
_N
NBIN
To add a channel
list:
•
EXff
to the selected
Favorite
Channel
Use _' to highlight an unchecked box next to a channel you
want to set as a fiworite, and then press @ to check the box.
Note: You must first use Channel Program or Channel Add/
Delete to add channels to the channel memory before setting
up favorite channels.
18
HM66 (E/F) Web 213:276
HM66
ENbook
Page 19 Thursday
February 23. 2006 2:49 PM
t
To delete the channel from the selected
Channel list:
Favorite
To tune your favorite
channel list:
Highlight a checked box and press @ to uncheck it.
2
iiiiiiB
Note: tf you try to add more than nine favorite channels per
input, an error message will appear. You will need to delete
(uncheck) a channel before you can add another.
Done and press @.
When done, highlight
To program
favorite
channels
for another
channels
using the favorite
1
Press (SD to display tile fitvorite channel list.
2
Press the corresponding number button (1-9) to select
your desired channel.
Note: To tune your favorite channels for another input,
press @ to select the other input.
input:
• Either... Highlight ANT 1, or ANT 2, which will change the
favorite channel settings in the selected input. (This will not
change the TV's current input.)
• Or... Press @ to select ANT 1, or ANT 2 and then repeat
steps 1-4, on page 18.
To clear your
favorite
channel
lists:
1
Press Mff_uand open tile Preferences
2
Highlight
Favorite
3
Highlight
Edit and press,_.
4
Highlight
Reset
and press @.
5
Highlight
Done
and press @.
Channels
iiiiiiilD2._
To tune your favorite
input:
Press FAVI / FAVV.
menu.
and press,_.
--
channels
for the current
ANT
lg
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 20 Thursday
February 23. 2006 2:49 PM
t
Settingthe ColorStreamHDaudio
mode
To set tile ColorStream
HD audio mode:
1
Press M_uand open tile Setup menu.
2
Highlight ColorStream
3
Press • or• to select Yes or No and press @ to display
the information.
,
• ,
• _N_R • •
HDl(or 2) Audio and press I_'.
CHURN
=
Viewing the CableCARDTM menu
A CableCARD r_'_enables you to view encrypted digital
channels. See "Connecting a digital CableCARD r_'_''
(Ir__"Installation Guide) for connection and subscription
information.
Note: Connecting your TVdirectly to the Audio/Video output of
your Set- Top-Box will assure a more vivid picture and enhance
your viewing enjoyment.
After the CabIeCARD r_'_is inserted, a CabIeCARD r_'_option
appears in the Applications
menu, with informational
screens provided by your digital CableCARD r_'_service (see
illustrations below).
Exrr
Note: The analog audio terminals for the ColorStream HD and
HDMt inputs are used in common. When the ColorStream HD
1 (or 2) audio mode is set to Yes, the HDMt 1(or 2) audio mode
is set to Digital and will be greyed out. When the ColorStream
HD 1 (or 2) audio mode is set to No, the HDMt 1 (or 2) Audio
changes to Auto.
To view the CabIeCARD
TM
menu:
1
Press M_uand open the Applications menu.
2
Highlight CableCARD
3
Press • or • to select one of the side menu items and
press @ to display the information.
TM
and pressl_'.
Settingthe HDMITM audiomode
To set the HDMI audio mode:
CaNeOARD(tm) Pairing
1
2
3
Press Mff_u
and open tile Setup menu.
Highlight HDMI 1 (or 2) Audio and press I_'.
Press • or • to select the HDMI audio mode (Auto,
Digital, or Analog) and press @. (Auto is the
recommended mode.) See "Connecting an HDMI or DVI
device to the HDMI input" (ir_r hlstallation Guide).
Note: The CableCARD TM menu is for informational
purposes only and has no user-adjustable options.
Settingthe QuickRestartTM feature
With the Quick Restart TM feature set to On, the TV will stay in
Standby mode for several minutes after the TV is turned off
(see Note on page 21 ).
If the TV is turned on flom Standby
appears immediately.
mode, the full picture
Note: The ColorStream HD 1/HD2 Audio settings influence the
HDMt Audio settings, tf ColorStream HD 1(or 2) Audio is set to
No, the HDMt 1 (or2) Audio setting changes to Auto. tf either
ColorStream HD 1 (or 2) Audio is set to Yes, the HDMt 1 (or 2)
Audio setting is set to Digital and will be greyed out.
2O
HM66 (E/F) Web 213:276
HM66
ENbook
Page 21 Thursday
Februar,¢ 23. 2006 2:49 PM
t
To set the Quick Restart
TM
feature:
1
Press MyNU
and open tile Setup menu.
2
HigMight Quick Restart and press •.
3
Press • or • to select either On or Off and Press @.
Viewingthe digital signalmeter
You can view tile digital signal meter in tile ANT 1 and ANT
2 digital TV input sources only.
To view the digital signal meter:
1
2
3
Note: tf Quick Restart is set to Off and you turn off the TV, it
can take several seconds for the picture to appear when you
turn on the TVagain. See "important notice about hot lamp
restart," below.
tf Quick Restart is set to On and you turn off the TV, the
following will occur for a few minutes.
• Thescreen (lamp) lights dimly, and
• Thefans continue to run.
This is a function of the Quick Restart Shutdown mode and is
not a TVmalfunction, tf you do not prefer this, set the Quick
Restart feature to Off
When the Quick Restart feature is set to Off, if you repeatedly
turn the TVon and off in a short period of time, the useful
service life of the lamp may be shorter than the average useful
service life (_. page 47).
IMPORTANT NOTICE ABOUT "HOT LAMP RESTART"
When the TV has been powered on long enough for
the lamp unit to get hot, it may take severn minutes for
the picture to appear on-screen in the following
situations:
° When the Quick Restart TM feature is set to Off and
you turn the TV off and then on again within a few
minutes; or
• If the TV is on when a short-term power failure,
power surge, or other similar power failure occurs,
such that the TV loses and regains power within a
few minutes.
This is a property of DLP TM TV lamp technology
and is NOT a sign of malfunction.
If this occurs, the yellow LED on the TV front panel will
blink (and the blue LED will be lit solid) until the TV is
finished restarting the lamp and the normal picture
appears. If both LEDs are blinking, you will need to
turn the TV off and then on again to restart the lamp.
Press MffNU
and open tile Setup menu.
Highlight Installation and press ,_.
A new set of Installation menu icons will appear onscreen, as shown below.
Open the Terrestrial menu, highlight Signal Meter,
and press @.
Channel
4
Program
Press ••'_
• to select the antenna input and digital
channel whose signal you want to check.
Note: The physical digital channel number listed in the
Signal Meter screen may not correspond to a virtual TV
channel number. Contact your local broadcasters to
obtain the RF channel numbers for your local digital
stations.
iiiiiAnt
....
1
Physical Digital Channel
Virtual
To close the screen
menu:
Digital
Cha,meJ
ii;i;i;
4
4/1
and return to the Terrestrial
Highlight Done and press @.
To return to normal
Press EXiT(._),
viewing:
21
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 22 Thursday
February 23. 2006 2:49 PM
To cancel
Viewing the system status
To view the system
Highlight
the reset:
No and press @.
Note: If you have previously set the TV to High Bright mode,
and have restored Factory Defaults, the TV wi// default to Low
Power mede. To set the TV back to High Bright mede, see
page 42.
status:
1
Press My_u
and open the Setup
2
Highlight Installation
and press @. A new set of
Installation menu icons will appear on-screen, as shown
below right.
menu.
;_
ii_¸
{i
iiiii Sleep Timer
• .•
E_
•
CHRTN
-
EXIT
3
Open the System Status menu, highlight System
Information, find press(/_.
4
Press • • to scroll through the menu bar to check the
Product Information and Software Version.
iiiiiiiiii ........
Jan 24 2006
!!!!!!!i;!
To close the screen and return
menu:
Highlight Done find press @.
To return
Press
to normal
11:04:47
Fw:17
to the Installation
viewing:
EXIT(_,
Restore Factory Defaults
To restore all settings
default values:
1
and channels
to their factory
Follow steps 1-3 above.
Press • • to scroll through the menu bar to select
Factory Defaults.
3
4
Enter your PIN code (or 0000 if no PIN code has been set).
Highlight Yes and press @. The TV will turn off
automatically after a few seconds. After the TV turns off.
unplug the TV power cord and then plug it in again to
complete the restore process.
22
HM66 (E/F) Web 213:276
HM66
ENbook
Page 23 Thursday
February 23. 2006 2:49 PM
t
Selectingthe videoinputsource
to view
To select the video input source
Labelingthe videoinputsources
You can label each video input source according to the type of
device you connected to each source, l¥om the following preset
list of labels:
to view:
1
Press @ on tile remote control or INPUT on tile TV
control panel.
2
Press 0-7 to select the input source you want to view,
which will depend on the input terminals you used to
connect your devices (ir_vInstallation Guide).
The current signal source displays in the top right corner
of the Input Selection
screen.
"- -"(default
Cable
DTV
Satellite/DSS
VCR
Laser Disk
DVD
Audio
|0 _rr 1
Video
1
Video
2
Receiver
Compact Disc
Video Recorder
R
O
label)
Game Console
ColorStream HD1
ColorStmam
Hide (to hide an unused
screen)
HD2
HDMI1
HDMI
@
ANT
Selection
2
Note: tf you soIoot ANT 2 in the Input selection screen, you can
select either "- -" or "Hide".
2
- @
/ _
to Select
Notes:
° When the Input Selection screen is open, you a/so can use
AV on the remote control (or the CHANNEL A V buttons on
the control panel) to change the input,
•
input in the Input
You can repeatedly press _ on the remote control or the
INPUT button on the TV control panel to change the input.
° You can label the video input sources according
specific devices you have connected to the TV
(F_y "Labeling the video input sources" at right),
° The source can be "hidden" (_
sources" at right).
To label the video input
sources:
1
Press MENU©
and open the Preferences
2
HigMight
3
to the
Press •
label.
menu.
Input Labeling and press @.
or •
to highlight
the video source you want to
"Labeling the video input
Favorite Channels
4
Press < or • to select the desired label for that input
source. Ifa particular input is not used, you can select
Hide as the label, which will cause that input to be
"grayed out" in the input list and skipped over when you
press @ on the remote control.
5
To save the new input labels, lfiglflight Done and press
,@. To revert to the factory default labels, lfigMight
Reset and press ,@.
(con tin ued)
23
HM66 (E/F) Web 213:27(
_4_J
HM66
ENbook
Page 24 Thursday
February 23. 2006 2:49 PM
t
Input labeling
example:
The screen below left shows the delimit Input Selection
screen (with none of the inputs labeled). The screen below
right is an example of how you could label the inputs if you had
connected a DVD player to VIDEO 1, Cable TV to VIDEO 2,
a video recorder to ColorStream
HDI, a DTV set-top box to
HDMI 1, and a satellite/DSS
set-top box to HDMI 2. Also note
that the ColorStream HD2 input is labeled "Hidden," which
means that the input will be skipped over when @ is pressed.
CaNe
ColorStream HD1
I_ Video Recorder
ColorStream HD2
I_
HDMI 1
@
ANT
CoEorStelam
The Channel Browser TM stores the most recently viewed
channels or inputs in a history list. In addition, it provides a list
of all the available channels on the ANTI input (up to 2000),
the ANT2 input (up to 2000) and a list of all the inputs on the
TV. This feature allows you to:
(Hidderl)
or inputs viewed.
• Quickly surf and tune your recently viewed channels/inputs
from the Channel Browser TM banner (illustrated on the next
page).
Satellite/DSS
2
ANT
-@
ND2
DTV
O HDM_
2
Usingthe Channel BrowserTM
• Keep a history of the last 32 channels
O DVD
VJrfeo 1
@ Video 2
Tuningchannels
] _to
Select
Input Selectionscreen
with no inputs labeled
2
- _
/
_to
Select
Input Selectionscreen with
all inputs labeledexcept input 4,
which has beenhidden.
• Suffvia Browse mode (to immediately
tune channels as you
highlight them in the Channel Browser TM banner) or Select
mode (to surf over channels in the browser banner before
you select one to tune).
• Quickly change inputs from the Inputs List.
• Set a "HOME" source foran ANT1 grANT2
channel
orTV
input.
To clear the input labels:
1
Press M_uand open tile Preferences menu.
To set the Channel
2
Highlight Input Labeling and press @.
1
Press M_uand open the Preferences menu.
3
Highlight Reset and press,@.
2
Highlight Channel
3
Press • to highlight Navigation,
and then press • or •
to select either Browse Mode or Select Mode.
History List
Inputs
4
List
BrowserTM:
Browser
Setup
and press @.
Power Off Clear(On)
On
Press • to highlight History List field, then press • or•
to select the setting you prefer either Power Off Clear
(On), On or Off.
Note: When History List is set to On, the channels and
inputs stored in the list will be saved through power on
and off. When History List is set to Power Off Clear (On),
the channels and inputs stored in the list will be cleared
with every power on/off cycle of the TV.
5
Press • to highlight ANT1 List field, then press • or •
to select On or Off.
6
Press • to highlight ANT2 List field, then press • or •
to select On or Off.
7
Press • to highlight Inputs List field, then press • or •
to select On or Off.
8
To save your entries, highlight Done and press @.
To return to factory detimlts, highlight Reset and press
24
HM66 (E/F) Web 213:276
HM66
ENbook
Page 25 Thursday
February 23. 2006 2:49 PM
t
To open the Channel
Browser
TM
Note: The Channel Browser TM banner will close
automatically if you do not make a selection within 30
seconds.
banner:
• Press _ •. ml•, or H_IEon the remote control.
• Press i_ •to surf back from the most recently viewed
channel through the last 32 channels or inputs in the History
list, ANT I channels list, ANT 2 channels list or the inputs
list.
To tune to a channel
1
• Press _i • to surf forward from the previous item in the
channel history, ANT 1, ANT 2, or inputs up to the most
recently viewed item or end of list.
or input in Select mode:
While watching TV, press _ • or m' • to open the
Channel Browser TM banner and surf back to a previous
item or surf forward to the next item in the list.
In Select mode, when you stop on an item in the browser
banner, it will be highlighted but the TV will not
automatically
tune to the channel or input.
Elements of the Channel BrowserTM banner
Press ,@ to tune the TV to the highlighted
1 2
3
Press E_
S to close the Channel
Browser
TM
item.
banner.
Adding and clearing channels and inputs in the
channel history
Adding
5
6
1
Input type
2
Highlighted
3
Channels
7
item (channel
8
9
10
11
or input)
stored in the channel
The Channel
history
4
Home instructions (this will be replaced once there are at
least 6 items in the History, ANT 1 or Inputs lists)
5
Cunent
list (History,
6
Current
input
7
Current antenna
8
Active channel
9
Channel
10
Resolution
11
Home source
ANT 1, ANT 2 or Inputs)
number
call letters (if available)
to the channel
History,
history:
Browser
TM
will store the following
channels:
• All channels that are tuned using the numeric buttons
remote control.
on the
• All channels that are tuned to using (_ or _, FAVII, or FAVT
on the remote control and inputs that are tuned to for at least
5 seconds.
Clearing
channels
from
• Reconfiguring the ANT
channel history.
ANT 1, ANT 2 and
to
Note: The Channel Browser TM banner opens in History List by
defaulL Once another list has been selected, the
Channel Browser TM will open in the last selected lisL
the channel
or input in Browse
1 or ANT
history:
history only if
Setup is set to
2 input will clear the
Note: See page16 for details on configuring
inpuL
• Removing
the CableCARD
TM
the antenna
will clear the channel
history.
• Once 32 channels or inputs are stored in the history list, the
oldest item will be removed from the list when a new
channel
1
inputs
• Turning offthe TV will clear the channel
History List in the Channel
Browser
"Power
Off Clear (On)."
After opening the Channel Browse/r_'_ banner, press • err
toggle between History, ANT 1, ANT 2 and Inputs.
To tune to a channel
and
Note: The TV will automatically tune to the previously viewed
channel or input whenever an item is selected that cannot be
tuned for various reasons.
type (cable or TV)
To toggle between
Inputs:
channels
The Channel Browsei r_'_automatically
creates a history of the
last 32 channels or inputs that were tuned by adding that
channel or input to the right of the list (revisited items are
moved to the end of the list).
or input is tuned.
mode:
While watching TV, press '_ • or _i • to open the
Channel Browse/r_'x banner and surf back to a previous
item or surf forward to the next item in the list.
In Browse
mode, when you stop on an item in the
browser banner, it will be highlighted and the TV will
automatically
tune to the channel or input.
2
Press
EXIT
O to close the Channel
Browser
TM
banner.
25
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 26 Thursday
February 23. 2006 2:49 PM
t
Usingthe Homefeature
To set a channel or input
as Home:
1
Tune the TV to the channel or input you would like to set
as the Home source.
2
Press and hold ._IE on the remote control for 3 seconds.
When HOME is saved, the Channel Browser TM banner
will appear at the bottom of the screen and the HOME
icon will flash green.
To tune to HOME:
Switching between two channels using
Channel Return
The Channel Return feature allows you to switch between two
channels without entering an actual channel number each time.
1
Select the first channel you want to view.
2
Select a second channel using the Channel Number
buttons (and the dash ((_)) button if selecting a digital
channel).
3
Press CH@TN
on the remote control. The previous channel
will display. Each rune you pre,i',i' o , the TV will switch
back and forth between the last two channels that were
tuned.
•
Press the ._IEbutton on the remote to tune to your HOME
channel or input. The Channel Browser TM banner will display
when HOME is tuned unless all lists have been turned to "Off"
in the Channel Browser Setup.
Note: trail lists are turned to off, Home may not be set at this
time, however, if it is already set, pressing the"_E button on the
remote will tune to the Home source, but will not display the
Channel Browser TM .
Tuning your favorite channels
To tune to the channels you programmed as Favorite Channels,
see page 18.
SS
CHRTN
Note:If you press C._T,from a non-antenna input, the TV
will return to the last-viewed ANT input and channel.
Switching between two channels using
SurfLockTM
The SurlLock TM leature temporarily "memorizes" one channel
in the C,(_TN
button, so you can return to that channel quickly
SS •
CHrRTN
flom any other channel by pressing
o • To memorize a
channel in the C,(_TN
button:
1
Tuning to the next programmed channel
Tune the TV to the channel you want to program into the
0 button.
CH
RTN
2
Press and hold C,ORTN
for"about 9_ssecond,i'suntil the message
"Channel Memorized" appears on the screen. The channel
lms been programmed into the C,4TNbutton.
Note:Thisfeature will not work unless you program channels
into the TV's channel memory (c;>page 17).
3
You can then change channels repeatedly, and when you
press C,4TN,the memorized channel will be selected.
Tuning to a specific channel (programmed
or unprogrammed)
The TV will return to the memorized channel one time only.
Once you press o and then change channels again, the CH
RTN memory will be cleared and the button will function as
Channel Return, by switching back and forth between the last
two channels that were tuned.
To tune to the next programmed
channel:
Press _'l or _# on the remote control or TV control panel.
Tuning analog channels:
Press the Channel Nul]nber buttons (0-9) on the remote
control. For example, to select channel 125, press 1, 2, 5.
Tuning
digital
SS
CHRTN
channels:
Press the Channel Number buttons (0-9) on the remote
control, followed by the dash ((_)) button and then the subchannel number. For example, to select digital channel 125-1,
press 1,2, 5,-, 1.
Note: If a digital channel is not programmed-either
through
the automatic channel scan (_ page 17) or the channel add/
delete function Or_' page 17)-you will have to tune the RF
channel using the Channel Number and the dash ((_)) buttons
on the remote control.
26
HM66 (E/F) Web 213:276
HM66
ENbook
Page 27 Thursday
February 23. 2006 2:49 PM
t
Selectingthe picturesize
You can view many program formats in a variety of picture
sizes--Natural, TheaterWide 1, TheaterWide 2,
TheaterWide 3, and Full.
The way the image displays in any of the picture sizes will w_ry
depending on the format of the program you are viewing.
Select the picture size that displays the cunent program the
way that looks best to you.
Natural picture size
• The image is displayed close to its originally formatted
proportion. Some program formats will display with
sidebars and/or bars at the top and bottom.
Natural picture size example: The way the image displays
will vary depending on the format of the program you are
currently watching.
Your picture size preferences can be saved for each input on
your TV.
To select the picture size:
1
Press p_cs_zE©
on tile remote control.
2
While the Picture Size screen is on-screen, press the
conesponding number button (0-4) to select the desired
picture size.
Conventional picture on a
conventional TV screen
Conventionalpicture in Natural sizeon
your wide-screen TV
TheaterWide I picture size (For 4:3 format program)
• The center of the picture remains close to its original
proportion, but the left and right edges are stretched wider to
fill the screen.
Natural
O
TheaterWide
1
TheaterWide
2
TheaterWide
3
Sh
\S
|O F.,i
_)
- _
/ _
to Select
Notes:
Pie S_ZE
• You also can repeatedly press o to select the desired
picture size (or press AV on the remote control while the
Picture Size screen is open).
• Full may not be available for some program formats (it will
be "grayed out" in the Picture Size screen).
•
You also can select the picture size using the menu system.
Select Picture Size in the Theater Settings menu. Select
the input for which you want to save your picture settings. To
save your settings, highlight Done and press _@.
TheaterWide
1 picturesizeexample
fheaterWide 2 picture size (for letter box pregrams)
• The picture is stretched wider to fill the width of the screen,
but only slightly stretched taller.
• The top and bottom edges of the picture are hidden. To view
the hidden areas, see "Scrolling the TheaterWide @ picture"
(_
page 28).
TheaterWide2 picture sizeexample
Using these functions to change the picture size (i.e.,
changing the height/width ratio) for any purpose other than
your private viewing may be prohibited under the Copyright
Laws of the United States and other countries, and may
subject you to civil and criminal liability.
(con tin ued)
27
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 28 Thursday
Februar,¢ 23. 2006 2:49 PM
t
TheaterWide 3 picture size (for letter box programs
with subtitles)
• Tile picture is stretched wider to fill tile width of the screen,
but only slightly stretched taller.
• The top and bottom edges are hidden. To view the hidden
areas (such as subtitles or captions), see "Scrolling the
TheaterWide _) picture".
Scrolling the TheaterWide® picture
(TheaterWide2 and3 only)
You can set separate scroll settings for tile TheaterWide 2 and
TheaterWide 3 modes for each input.
To set the scroll settings:
C)
C)
© O O
O O O
|ABCDE_a
|
m
ABODEFG
C) C)
L-> C)
-
-
-
1
Press M_uand open the Video menu.
2
Highlight Theater Settings and press @.
I
TheaterWide
3 picturesize example
_ici,Ji;s;iii,,gs
;;;
Full picture size (for 16:9 [480i, 480P1source
programsonly)
• It" receiving a squeezed 4:3 tonnat program, tile picture is
stretched wider to fill the width of the screen, but not
stretched taller.
• None of the picture is hidden.
©0
• ,
• ENTER •
C_RTtl:•
EXIT
3
In the Picture Size field, select either TheaterWide
2
or TheaterWide
3 (you cannot scroll in any other mode).
4
Pregg •
5
Press • or l_"to scroll the picture up and down as needed,
from -10 to +20.
6
To save the new settings, highlight Done and press @.
To revert to the factory defaults, highlight Reset and
press @.
to highlight
the Picture
Scroll
field.
Fullpicturesizeexample
Notes:
• tfyou select one of the TheaterWide ® picture sizes, the top
and bottom edges of the picture (including subtitles or
captions) may be hidden. To view the hidden edges, either
scroll the picture (TheaterWide 2 and 3 only) or try viewing
the program in Full or Natural picture size.
•
When selecting the picture size, the way the image displays
will vary depending on the format of the program you are
currently watching.
28
HM66 (E/F) Web 213:276
HM66
ENbook
Page 29 Thursday
February 23. 2006 2:49 PM
t
Usingthe autoaspectratiofeature
When the auto aspect ratio feature is set to On, the picture size
is automatically selected when one of the following input
sources is received:
• A 480i signal from the VIDEO 1, VIDEO 2, ColorStream
HD-1, or ColorStream HD-2 input.
• A 1080i, 480i, 480p, or 720p signal fiom the HDMI input.
Selectingthe cinemamode
(480i signalsonly)
When you view a DVD (480i signal; 3:2 pulldown processed)
from a DVD player connected to the VIDEO 1, VIDEO 2,
ColorStream
HD-1/HD-2 (component video), or HDMI
inputs on the TV, smoother motion can be obtained by setting
the Cinema Mode to Film.
To set the Cinema
4:3 normal
Natural
4:3 letter box
TheaterWide
16:9 full
Full
Not defined
(no ID-I data
or HDMI
Selecting
aspect
(with sidebars)
2
Mode
to Film:
1
Press M_uand open the Video menu.
2
Highlight Theater Settings and press @.
3
In the Cinema Mode field, select Film.
4
To save the new settings, highlight Done and press @.
To revert to the factory defaults, highlight Reset and
press @.
the picture size (ir_, page 27)
data)
Note: Theauto aspect ratio feature is not applicable to
antenna or cable input sources.
To turn on tile auto aspect
ratio feature:
1
Press M_uand open the Video lnenu.
To set the Cinema
2
Highlight Theater Settings
Select Video in step 3 above.
3
In the Auto Aspect
and press @.
Mode
to Video:
Ratio field, select On.
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Re,e, iiiiiiiiiiiiiiiiiiii
Done
4
To save the new settings, highlight Done and press @.
To revert to the factory defaults, highlight Reset and
press @.
To turn off the auto aspect
Select Off in step 3 above.
ratio feature:
29
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 30 Thursday
February 23. 2006 2:49 PM
t
Adjusting the picture quality
Adjustingthe picture
You can adjust the picture quality (contrast, brightness,
tint, and sharpness) to your personal preferences.
color,
Selecting the picture mode
You can select your desired picture settings
modes, as described below.
from t_)ur different
contrast
lower
higher
brightness
darker
lighter
color
paler
deeper
Sports
Bright and dynamic picture (factory setting)
tint
reddish
greenish
Standard
Standard picture settings (factory setting)
sharpness
softer
sharper
Movie
Lower contrast for darkened room dactory
setting)
Preference
Your personal preferences
To select the picture
mode using the menu system:
To adjust the picture quality:
1
2
3
1
Press My_u
and open tile Video menu.
2
Highlight Picture Settings and press @.
3
In the Mode field, select the picture mode you prefer.
Press M_uand open the Video menu.
Highlight Picture Settings
and press @.
Press • or • to select the picture quality you want to
adjust (Contrast,
Brightness,
Color, Tint, or
Sharpness),
and then press • and • to adjust the setting,
as described in the table above.
Sharpness
4
To save the new settings, highlight Done and press @.
To revert to the factory defaults, highlight Reset and
press @.
Notes:
•
The picture mode you select affects the current input
only (ANT 1 in the example above). You can select a
different picture mode for each input.
•
tfyou select one of the factory-set picture modes
(Sports, Standard, or Movie) and then change a
picture quality setting (for example, increase the
contrast or change the color temperature), the picture
mode automatically changes to Preference in the
Picture Settings menu.
•
if you have previously set the TV to High Bright mode,
and have chosen Reset in item 4 above, the TV will
default to Low Power mode. To set the TV back to High
Bright mode, see page 42.
4
To save the new settings, highlight Done and press @.
To revert to the factory defaults, highlight Reset and
press @.
The picture qualities you adjusted are automatically
saved in
the Preference
mode (_ "Selecting the picture mode,"
above left).
3O
HM66 (E/F) Web 213:276
HM66
ENbook
Page 31 Thursday
February 23. 2006 2:49 PM
t
Usingthe closedcaptionmode
Note: A closed caption signal may not display in the following
situations:
• When a videotape has been dubbed
The closed caption
• When the signal reception is weak
mode has two options:
• Captions--An
on-screen display of the dialogue, narration,
and sound effects of TV programs and videos that are closed
captioned (usually marked "C(7' in proglam guides).
• Text--An
on-screen display of information
not related to
the current program, such as weather or stock data (when
provided by individual stations).
To view captions
or text:
1
Press M_u and open the Preferences
2
Highlight
3
Press • or • to select the desired closed caption mode and
press @.
Closed
Caption
menu.
Mode and press •.
• When the signal reception is non-standard
Closed Caption Advanced
You can customize the closed caption display characteristics
by changing the text size, type, edge, color, and the
background color. You cannot set the Caption Text and
Background as the same color.
Notes:
• This feature is available for digital channels only.
•
You cannot set the Caption Text and Background
same color.
To customize
1
2
3
the closed
as the
captions:
Press Mff_u
and open the Preferences menu.
Highlight Closed
Caption Advanced
and press @.
Press • or • to highlight the characteristic
you want to
change, and then press • or • to select the format for that
characteristic.
To view captions:
Highlight CC1, CC2, CC3, or CC4. (CC1 displays
translation of tile primary language in your area.)
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
.....................
................................................................................
Reset
Done
4
Note: tf the program or video you selected is not closed
captioned, no captions will display on-screen.
To view text:
Highlight
T1, T2, T3, or T4.
To save the new settings, highlight Done and press @.
To revert to the factory defaults, highlight Reset and
press @.
Caption
Size
Caption
Text
Type
Auto,
Small, Standard,
Large
Auto, Del:ault, Mono w. Serif. Prof. w. Serif'.
Mono w/o SeriL Prop w/o SeriL Casual,
Cursive, Small Capitals
Caption
Edge
Text
Auto, None, Raised, Depressed, Uniform,
Left Drop Shadow, Right Drop shadow
Caption
Color
Text
Auto, Black, White, Red, Green,
Yellow, Magenta, Cyan
Blue,
Auto, Black, White, Red, Green,
Yellow, Magenta, Cyan
Blue,
Background
Color
Note: If text is not aw_ilable in your area, a black rectangle
may appear on your screen. If this happens, tum the
Closed Caption Mode Off.
To turn off the Closed Caption
Select Off in step 3 above.
mode:
31
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 32 Thursday
February 23. 2006 2:49 PM
t
Digital closed captions
You can use the Digital CC/Audio Selector to select digital
closed caption services (if available), which will temporarily
ovenide closed captions for digital channels only.
When such services are not available, the Digital CC/Audio
Selector presents a default list of services. If the selected
service is not available, the next best service will be used
instead.
To select
digital
closed
2
Highlight
CC/Audio
Selector
menu.
and press @.
•
EN_R •
CHRrN=
Exrr
Press • or • to select Closed
Caption,
• or • to select the desired service.
!!!!!!!!!!!!!!!!!!_!_ii
¸¸2222222222:
4
Press=c/.
Mute ------*Mute ------*Volume --*-'7
If the closed caption mode is set to Off when you select
"MUTE" mode, the closed caption feature is automatically
activated. To mute the audio without automatically
actiwtting
the closed caption feature, use _ to set the volume to 0. See
"Using the closed caption mode" (ir_ page 31 )
for more information on closed caption modes.
Using the digital audio selector
CableCARD
3
Press M_Eto partially reduce (1/2 MUTE) or turn off (MUTE)
the sound. Each time you pressS S MUTE
©, the mute mode wdl change
in the following order:
[---l/2
Press M_Uand open tile Applications
.
Muting the sound
captions:
1
Digital
Adjustingthe audio
None
and then press
You can use the Digital CC/Audio Selector to conveniently
switch between audio tracks on a digital channel (for those
channels that have multiple audio tracks). This temporarily
overrides the audio track chosen by the language option under
Audio
Setup (see "Selecting stereo/SAP broadcasts," on
page 33).
To use the digital
audio
selector:
1
Press M_Uand open the Applications
2
Highlight
Digital
CC/Audio
menu.
Selector
!
and press @.
x'
ii!Cham/e_Browser
iii
iiiC_b_CARE' iiii
• .• • _N_R • •
3
4
CH_l =•
Press • or • to select Audio,
select the desired service.
Exrr
and then press • or • to
PressE_'_.
32
HM66 (E/F) Web 213:276
HM66
ENbook
Page 33 Thursday
February 23. 2006 2:49 PM
t
Selecting stereo/SAP broadcasts
The multi-channel TV sound (MTS) feature allows you to
output high-fidelity stereo sound. MTS also can transmit a
second audio program (SAP) containing a second language,
music, or other audio information (when provided by
individual stations).
The MTS feature is not available when the TV is in VIDEO
mode. When the TV receives a stereo or SAP broadcast, the
word "STEREO" or "SAP" appears on-screen when RE_LLis
pressed.
• tfyou have SAP on and the station you are watching is not
broadcasting a second audio program, the station's normal
audio will be outpuL However, occasionally there is no
sound at all in SAP mode. tf this happens, set the MTS
feature to Stereo mode.
Adjusting the audio quality
You can adjust the audio quality by adjusting
and balance.
the bass, treble,
To adjust the audio quality:
To listen to stereo sound:
1
Press M_uand open the Audio menu.
1
Press u_u and open tile Audio menu.
2
Highlight Audio Settings and press @.
2
Highlight Audio Setup and press @.
3
Press • or • to highlight the item you want to adjust
(Bass, Treble, or Balance).
3
In the MTS field, select Stereo.
4
Press • or • to adjust the level.
• _ makes the bass or treble weaker or increases the
balance in the left channel (depending on the item
selected).
Language
Speakers
4
To save the new settings, highlight Done and press @.
To reset the settings to the factory defaults, highlight
Reset and press @.
Notes:
•
tfyou leave the TV in Stereo mode because it will
automatically output the type of sound being broadcast
(stereo or monaural).
•
If the stereo sound is noisy, select Mono to reduce the
noise.
° • makes the bass or treble stronger or increases the
balance in the right channel (depending on the item
selected).
5
To save the new settings, highlight Done and press @.
To reset the settings to the factory defaults, highlight
Reset and press @.
To listen to an alternate
language on an ATSC digital
station (if available):
Highlight the Language field in step 3 above, and then press
• or • to select the language you prefer.
To listen to a second
station
(if available):
Select
audio
program
on an analog
SAP in step 3 above.
Notes:
° A second audio program (SAP) can be heard only on those
TV stations that offer it. For example, a station might
broadcast another language as a second audio program. If
you have SAP on, you will see the current program on the
screen but hear the other language instead of the program's
normal audio.
33
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 34 Thursday
February 23. 2006 2:49 PM
t
Usingthe StableSound® feature
Selecting the optical audio output format
Tile StableSound _ feature limits tile highest volume level to
prevent extreme changes in volume when the signal source
changes (for example, to prevent the sudden increase in
volume that often happens when a TV program switches to a
commercial).
You can use this feature to select the optical audio output
format when you connect a Dolby Digital decoder or other
digital audio system to the Optical Audio Out terminal on
the TV
(Ir__ "Connecting
a digital audio system" in the Installation
Guide).
To turn on the StableSound
_ feature:
To select the optical
1
Press M_uand open the Audio menu.
2
Highlight Audio Settings
3
In the StableSound
field, select On.
To save the new settings, highlight Done and press @.
To revert to the factory defaults, highlight Reset and
press @.
Note: The RESET function returns your audio adjustments
to the following factory settings:
Bass .........
Treble ........
Balance ......
StableSound...
output
format:
I
Press Mff_u
and open the Audio menu.
2
Highlight Audio Setup and press @.
3
In the Optical Output Format field, select either
Dolby Digital or PGM, depending on your device.
4
To save the new settings, highlight Done and press @.
To revert to the factory defaults, highlight Reset and
press @.
10o
Bass
4
and press @.
audio
center (50)
center (50)
center (0)
Off
To turn off the StableSound
feature:
Select Off in step 3 above.
Turning off the built-in speakers
You can use this feature to turn off the TV speakers when you
connect an audio system to your TV (_ "Connecting
a digital
audio system" and "Connecting an analog audio system" in the
hlsmllation
Guide).
To turn off the built-in
speakers:
I
Press Mff_u
and open the Audio menu.
2
Highlight Audio Setup and press @.
3
In the Speakers field, select Off.
Opticat
4
Outpul
Format
DoJby Digital
To save the new settings, highlight Done and press @.
To revert to the ti_ctory delimits, highlight Reset and
press 0.
To turn on the built-in speakers:
Select On in step 3 above.
34
HM66 (E/F) Web 213:276
HM66
ENbook
Page 35 Thursday
February 23. 2006 2:49 PM
Usingthe Locksmenu
When tile correct PIN code is entered, tile Locks menu opens.
The Locks menu includes the Enable Rating Blocking, Edit
Rating Limits, Channels Block, Input Lock, Front (control)
Panel Lock, and New PIN Code features. You can use these
features after entering the conect PIN code.
Edit Rating Limits
Input Lock
Oif
ii New PIN Code
i
Entering the PIN code
1
Press M_uand highlight the Locks menu icon.
If you cannot remember your PIN code
Wllile tile PIN code enterin_ screen is displayed, pie..
" S_ RECALL
O
four times witllin five seconds. Tile PIN code will be cleared
and you can enter a new PIN code.
Front Pane_ Lock
Changingyour PIN code
Otf
New PIN Code
E_ER •
2
_Rm :
EXIT
Press •, which displays tile PIN code entry screen.
• The Lock System screen (below) appears if a PIN
code has not been stored. Press the Channel Number
buttons to enter a new four-digit code, enter the code a
second time to confirm, and press @.
1
Press M_uand highligllt tile Locks menu icon.
2
Press • to display the PIN code entering screen.
3
Enter your four-digit PIN code and press ,@.
4
Press • to highlight New PiN Code and press @.
_R
Tile Locks/Active
screen (below) appears if tile PIN
code is already stored. Use the Number buttons to enter
your four-digit code and press @.
• •
_E_U :
EXIT
5
Press tile Number buttons to enter a new four-digit code.
Retype the numbers to confirm the PIN code you entered.
6
Press @. The new PIN code is now active.
If the wrong PIN code is entered, tile message "Incorrect PIN
code, please try again!" appears. Highlight Retry and press
@. Enter the code again and press @.
35
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 36 Thursday
February 23. 2006 2:49 PM
t
BlockingTV programsand movies
by rating(V-Chip)
Some TV programs and movies include signals that classify
the content of the proglam (violence, sex, dialog, language).
The V-Chip feature in this TV detects the signals and blocks
the programs according to the ratings you select. (See the
tables at below right for rating descriptions.)
Note: Rating blocking is a function of the V-Chip feature in this
TV, which supports the U.S. V-Chip system only.
To block and unblock
TV programs
and movies:
1
Press Mff_u
and highlight tile Locks menu icon.
2
Press • to display the PIN code entering screen.
3
Enter your four-digit PIN code and press @.
4
Press • to highlight Enable
5
Press • and • to select On, and press @.
Rating
2
Highlight AIt RS and press ,@. The Edit Alternate
Ratings screen will appear. (This button will only be
awulable it your television has detected that the
broadcaster
is send alternate ratings with that program.)
3
Press • • • • and then press @ to select the level
blocking you prefer. A box with and "X" is a rating
will be blocked. (The information contained within
menu window will depend on what the broadcaster
providing.)
4
When done selecting the ratings you want to block,
highlight Done and press @.
5
In the Edit Rating
press @.
of
that
this
is
Limits screen, highlight Done and
Blocking.
Note: The above illustration is example data only. The
Alternate Ratings screen on your TV may not look the same.
FrontPane_ Lock
Oft
Independent rating system for broadcasters
6
R_!ifi_
Press •
The Edit
7
to highlight
Rating
Edit Rating
Limits
Limits and press ,4_.
screen (below)
appears.
Press •••
• and then press ,@ to select the level of
blocking you prefer. A box with an "X" is a rating that will
be blocked. As you highlight a rating, a definition for the
rating appears at the bottom of the screen.
When done selecting the ratings you want to block,
higMight Done and press ,@.
TV-MA
TV-14
Mature Audience Only (This program is specifically
designed to be viewed by adults and therefore may
be unsuitable for children under 17.)
L) Crude or indecent language S) Explicit sexual
activity V) Graphic violence
Parents Strongly Cautioned (This program contains
some material that many parents would find
unsuitable for children under 14 years of age.)
D) Intensely suggestive dialog L) Strong, coarse
language S) Intense sexual situations V) Intense
violence
Parental Guidance Suggested (This program
contains material parents may find unsuitable for
iiiii
¸
Blocking TV programs
and movies by alternate
ratings:
The alternate rating system is provided by some broadcasters
as a supplement the standard V-Chip ratings. This system is
dependant on the broadcaster's information.
1
Repeat steps
TV-PG
younger children.)
D) Some suggestive dialog L) Infrequent coarse
language S) Some sexual situations V) Moderate
violence
TV-G
General Audience (Most parents would find this
program suitable for all ages.)
Directedto Older Children (This program is designed
TV-Y7,
TV-Y7 FV
for children age 7 and above. Note: Programs in
which fantasy violence may be more intense or more
combative than other programs in this category are
designated Y7FV.)
All Children (This program is designed to be
appropriate for all children.)
TV-Y
1-6 above.
36
HM66 (E/F) Web 213:276
HM66
ENbook
Page 37 Thursday
February 23. 2006 2:49 PM
t
Independentrating systemlor movies
X
X-rated (For adults only)
NC-17
Not intended for anyone 17 and under
R
Restricted (Under 17 requires accompanying
or adult)
PG-13
Parents Strongly Cautioned (Some material may be
inappropriate for children under 13)
PG
Parental Guidance Suggested
not be suitable for children)
G
General Audience (Appropriate
parent
5
Using A•'4 I_ buttons, select the input for which you
want to change the rating limits (ANT1, or ANT2) and
press @.
A list of the channels available for that input will be
displayed along with the call letters for each channel, if
available.
6
Press A• to lfiglfiight the channel you want to block, and
press ,@, which puts an "X" in the box next to that
channel.
(Some material may
2
_--
for all ages)
Notes:
• tfyou place an 'X" in the box next to "'None" Rated,"
programs rated "None" will be blocked, however, programs
that do not provide any rating information will not be
blocked.
° Todisplay the rating of the program you are watching, press
o on the remote control, tf it is rated "None, the word
"NONE"appears in the RECALL screen (as shown below
right). If rating information is not provided, no rating will
appear in the RECALL screen.
RECALL
I
I
I
I
I
I
I
I
I
I
Blocking channels
4
--
[]
[]
_
--
D
;
2
;;n_;i
i
7
8
Repeat step 6 for other channels you want to block.
HigMight Done and press @.
To unblock
individual
channels:
In step 6 above, press A• to highlight the channel you want to
unblock, and then press @ to remove the "X" from the box,
and then highlight Done, and then press @.
To block all channels
at once:
Highlight Block All in step 6 above, and then highligllt Done,
and press @.
To unblock
With tile Channels Block feature, you can block specific
channels. You will not be able to tune blocked channels unless
you clear the setting first.
[]
all locked
channels
at once:
Highlight Allow All in step 6 above, and then highlight Done
and press @.
To block channels:
O ANT 2
1
Press Mff_u
and highlight tile Locks menu icon.
2
Press • to display the PIN code entering screen.
3
Enter your four-digit PIN code and press @ (ir_ page 35).
4
Press • to highlight Channels
Input Lock
Front Pane_ Lock
!!! New PIN Code
[]
Block and then press @.
O!f
Otf
iii
(con tin ued)
37
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 38 Thursday
February 23. 2006 2:49 PM
Unlocking programstemporarily
Usingthe input lock feature
If you try to tune the TV to a prograln that exceeds the rating
limits you set, the TV will enter program lock mode and the
following message will appear on-screen:
You can use the Input Lock feature to lock the video inputs
(VIDEO 1, VIDEO 2, ColorStream
HD-1, ColorStream
HD-2, HDMI 1, and HDMI 2) and channels 3 and 4. You will
not be able to view the input sources or channels until you
unlock the inputs.
You can either temporarily unlock the program or select an
unlocked program to watch.
To temporarily
1
2
Press
unlock the program:
MUTEc),
Enter your four-digit PIN code and press @. If the correct
code is entered, the program lock mode is released and the
normal picture appears. All locking is disabled until the
TV is turned off, and will be enabled when the TV is
turned on again.
To lock/unlock
1
2
3
4
5
the video inputs:
Press M_u and highlight
Press •
the Locks
menu icon.
to display the PIN code entering
screen.
Enter your four-digit
PIN code and press @.
Press •
Input Lock
to highlight
and press I_.
Press • or• to select the level of video input locking you
prefer, as described below.
Video: Locks VIDEO 1, VIDEO 2, ColorStream
HDI/
HD2, HDMI I/HDMI 2.
Video+:
Locks VIDEO 1, VIDEO 2, ColorStream
HD2, HDMI I/HDMI 2, and channels 3 and 4.
HDI/
• Select Video+ if you play video tapes via an ANT input.
• When a CableCARD TM is inserted, Video+ will not
lock channels 3 and 4.
Off: Unlocks
6
all video inputs and channels
3 and 4.
Press @.
38
HM66 (E/F) Web 213:276
HM66
ENbook
Page 39 Thursday
February 23. 2006 2:49 PM
t
Usingthe control panel lock feature
You can lock the control panel to prevent your settings flom
being changed accidentally (by children, for example). When
the control panel lock is On, none of the controls on the TV
control panel will operate except POWER.
To lock the control
You can set the sleep timer to turn offthe TV after a set length
of time (maximum of 180 minutes).
To set the sleep timer:
panel:
1
Press M_uand highlight tile Locks menu icon.
2
Press • to display the PIN code entering screen.
3
Enter your four-digit PIN code and press (/_.
4
Press • to highlight Front Panel
5
Press • and • or • to highlight On and press @. When
the control panel is locked and a button on the control
panel except POWER button is pressed, the message
"NOT AVAILABLE" appears.
Channels
Settingthe sleeptimer
Lock.
Press SLFEEP
o on the remote control to set the length of time until
ss sLFE_E
the TV turns oft\ Repeatedly pre._'s
o P to increase the time in
10-minute increments or press • or • to increase or decrease
the time in 10-minute increments, to a maximum of 180
minutes.
To cancel
Press
o
SLFEEP
the sleep timer:
until it is set to 0 minutes.
To set the sleep timer using the on-screen
1
Press M_uand open the Setup
2
Highlight Sleep
menus:
menu.
Timer and press,@.
Block
Input Lock
To unlock the control panel:
Highlight Off in step 5 above, or press and hold the
VOLUME -button on the TV control panel for about 10
seconds until the volume icon appears on-screen.
ENrE_ •
3
Press the Number buttons
10-minute increments.
C_RrN:,
EXff
to enter the length of time in
HHHHHHH
HHHHHHH
Cancel
4
Highlight
Done and press @.
Notes:
•
When a power failure occurs, the sleep timer setting
may be cleared.
•
To display the amount of time left on the sleep timer,
press _L.
To display
Press
the remaining
sleep time:
SLEEPer).
Note: A message will display on-screen when there is one
minute remaining on the sleep timer.
39
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 40 Thursday
February 23. 2006 2:49 PM
t
DisplayingTV settinginformation
on-screenusingRECALL
To display
TV setting
information
on-screen:
Press RE_L_on tile remote control.
The following
(if applicable):
int_rmation
will display on-screen
Understandingthe auto power off
feature
The TV will automatically turn itself off after approximately
15 minutes if it is tuned to a vacant channel or a station that
completes its broadcast for the day. This feature functions in
ANT 1 and ANT 2 modes only.
Understandingthe last mode
memory feature
Sample RECALL screen
Current input (ANT 1, ANT 2, VIDEO 1, etc.)
If ANT 1 or ANT 2 is the current input, whether it is Cable
TV ("CABLE") or off-air ("TV")
Channel number (if in ANT 1 or ANT 2 mode)
If the power is cut off while you are viewing the TV, the
Last Mode Memory feature automatically
turns on the TV
when the power is resupplied.
Note: You should unplug the TV's power cord if it is possible
that you will be away from the TVfor an extended period of time
after the power is restored.
Signal strength indicator (bar graph in lower right corner of
screen; for ATSC signal only)
Note: The signal strength indicator will react to fading and
increasing signals.
Remaining time on sleep timer (if set)
Stereo or SAP audio status
V-Chip rating status
Picture size
Video resolution
Lamp mode (appears only if the TV is in High Bright mode)
To close the RECALL
screen:
Press RE_L_again.
40
HM66 (E/F) Web 213:276
HM66
ENbook
Page 41 Thursday
February 23. 2006 2:49 PM
t
Notes:
Usingtheadvancedpicturesettings
features
• ffthe currentinputisANT
1, ANT2, VIDEO 1, or VIDEO
2, the menu will display the text "CableClear. " The
available selections are Off, Low, Middle, High, and
Auto.
• if the current input is ColorStream HD1, ColorStream
HD2, or HDMI, the menu wi// display the text DNR The
available selections are Off, Low, Middle, High and
Auto. Auto will react proportionally to the strength of
the noise. Low, Middle, and High will reduce the noise
in varying degrees, from lowest to highest, respectively.
Using dynamic contrast
When dynamic contrast is set to On, the TV will detect
changes in the picture quality that affect the appearance of your
contrast settings and then automatically
adjust the video.
When dynamic contrast is set to Off, the settings selected
Contrast field in Picture Settings will be used.
To select dynamic
contrast
in the
4
preferences:
1
2
Press M_uand open tile Video menu.
3
In the Dynamic Contrast
To save the new settings, highlight Done and press @.
To revert to the factory defaults, highlight Reset and
press @.
Using MPEG noise reduction
Highlight Advanced Picture Settings and press @.
field, select either On or Off.
The MPEG noise reduction feature allows you to reduce
visible interference
caused by MPEG compression.
Choices
for MPEG noise reduction are Off, Low, Middle, and Nigh. Off
is automatically
selected when this feature is disabled ("grayed
out").
To select the MPEG
NNNNNNNNNNNNNNNNNIIi!
Reset
4
iiiiiiiiiiiiiiii
Done
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
To save the new settings, highlight Done and press @. To
revert to the factory defaults, highlight Reset and press
1
2
Highlight Advanced Picture Settings and press @.
Lamp
Contrast
Low
the CableClear/DNR
4
Power
iiiiii
Off
iiiiiiiiiiiiiili
Reset
allows you to
This may be
signal
video cassette
On
Mode
Game Mode
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_
reduction)
1
2
3
Press _u and open the Video menu.
Dynamic
Using CableClear /DNR (digital noise
The CableClear _?digital noise reduction feature
reduce visible interference in your TV picture.
useful when receiving a broadcast with a weak
(especially a Cable channel) or playing a noisy
or disc.
level:
Press • or • to highlight the MPEG Noise Reduction
field, and then press • or • to select either Off, Low,
Middle or High.
Note: If you select the Movie picture mode and then set
the dynamic contrast to On, the picture mode will
automatically change to Preference in the Picture
Settings menu.
To change
noise reduction
iiiiiiiiiiii
iiili iiiii
Done
To save the new settings, higMigl-a Done and press @.
To revert to the factory defaults, highlight Reset and
press @.
settings:
Press _u and open the Video menu.
HigMight Advanced Picture Settings and press @.
In the CableClear/DNR
setting.
Dynamic Contrast
field, select your desired
Or}
iiiiii ColorTemperature
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Rese_
iiiiiiiiiiiiiiii Do_e
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_i_!i
(con tin ued)
41
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 42 Thursday
February 23. 2006 2:49 PM
t
Selecting the color temperature
Selecting the lamp mode
You can change tile quality of tile picture by selecting flom
three preset color temperatures (cool, medium, and warm), as
described below.
You can select either the High Bright
mode.
• The High
brightness
or Low Power lamp
Bright mode is useful when additional
is desired
picture
(such as in a bright room).
cool
blueish
To select the lamp mode:
medium
neutral
1
Press M_uand open the Video menu.
warm
reddish
2
Highlight Advanced Picture Settings and press @.
To select the color temperature:
1
Press M_uand open tile Video menu.
2
Highlight Advanced Picture Settings
3
In the Color Temperature
field, select the mode you
prefer (Cool, Medium, or Warm).
and press @.
• _
CableClear
Auto
MPEG Noise Reduction
Low
iiiii
iiii!i!
Lamp
Mode
LOW
Game Mode
0HFtl =•
Exrr
In the Lamp Mode field, select High Bright
Power, whichever you prefer.
or Low
Power
Off
Reset
4
3
• _N_R •
y
Done
CableClear
To save the new settings, highlight Done and press @.
To revert to the factory defaults, highlight Reset and
press @.
Auto
MPEG Noise Reduction
Color
Temperature
Low
Cool
Game Mode
Note: tf you se/ect one of the factory-set picture modes
(Sports, Standard, or Movie) and then change the co/or
temperature mode, the picture mode automatica//y
changes to Preference in the Picture Settings menu.
Off
Reset
4
Done
To save the new settings, higMight Done and press @.
To revert to the factory defaults, higMight Reset and
press @.
Note: ff you set the/amp mode to Low Power, each time
you turn on the TV, the/amp wi// start out in High Bright
mode but wi// switch to Low Power mode after a short
period of time, You may notice a change in screen
brightness when this happens. This is norma/ and is not a
sign of ma/function.
42
HM66 (E/F) Web 213:276
HM66
ENbook
Page 43 Thursday
Februar,¢ 23. 2006 2:49 PM
t
Usingthe Game Mode feature
You can use tile Game Mode feature for shorter fralne delays
when playing a video game requiring split-second
timing
between the on-screen display and input t¥om the controller
(such as music creation and high-action games).
Note: To use the Game Mode feature, the current video input
must be Video 1, Video 2, ColorStream HD1,
ColorStream HD2, HDMI 1 or HDMI 2. The Game Mode
cannot be turned on when any other video input is selected.
To turn on Game
Mode:
1
Press Mff_uand open the Video menu.
2
Highlight
3
Press • or • to highlight the Game
press • or • to select On.
picture settings and press @.
Advanced
Mode
Usingthe advancedaudiosettings
features
Usingthe SRSWOW Msurround sound
feature
WOW TM is a special combination
of SRS Labs audio
technologies
(SRS 3D, SRS FOCUS, and SRS TruBass) that
creates a thrilling surround sound experience with deep, rich
bass from stereo sound sources. Your TV's audio will sound
fuller, richer, and wider.
To adjust
To turn off Game
mode (ir_ "Selecting
Press Mff_uand open the Audio
menu.
Highlight
Settings
Advanced
Audio
stereo/SAP
and press @.
Press • or • to highlight the WOW feature you want to
adjust, and then press • or • to adjust the item.
Mode:
WOW: SRS TruBass
on the remote control (Ir_'rpage 23);
CH
• changing the channel using the Numbers or (_/_J,
"_i 4, _, I_, orFAVA/FAVV,
•
settings:
Done
Select Off in step 3 above or change the video input.
You can change the video input in any of the following ways.
• pressing _
TM
Put the TV in STEREO
broadcasts" page 33).
2
3
4
Resel
the WOW
field, and then
Turning the TVoffand
Off.
Low
• WOW: SRS 3D -- To turn the surround sound effect
On or Off.
OH RTN
o ,
Note: If the broadcast is monaural, the SRS 3D effect will
not work.
back on again will set Game Mode to
• WOW: SRS Focus -- To turn the vocal emphasis effect
On or Off.
• WOW: SRS TruBass -- To select the desired bass
expansion level (Off, Low, or High).
5
To save the new settings, highlight Done and press @.
To revert to the factory defaults, highlight Reset and
press 0.
WOW, SRS and Ce) symbol are trademarks of SRS Labs, Inc.
WOW technology is incorporated under license from SRS Labs, Inc.
43
t
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 44 Thursday
February 23. 2006 2:49 PM
t
Generaltroubleshooting
Before calling a service technician, please check this entire
chapter for a possible cause of the problem and some solutions
you can try.
Black box on screen
• The Closed Caption feature is set to one of the Text
modes (T1, T2, T3, or T4). Set the Closed
Caption
feature to Off (t_¢ page 31).
TV plays a recorded anouncement when LEDs are blinking
• When certain non-standard conditions occur, the LEDs
on the TV will blink and the TV will play a recorded
"voice announcement"
describing the condition (see
"LED indications" on page 46 for details).
TV stops responding to controls
• If the TV stops responding to the controls on the remote
control or TV control panel and you cannot turn off the
TV, press and hold the POWER button on the TV control
panel for 5 or more seconds to reset the TV.
Other problems
• If your TV's problem is not addressed in this
Troubleshooting
section or the recommended solution
has not worked, use the Restore Factory Defaults
procedure (zr_ page 22).
TV will not turn on
Make sure the power cord is plugged
in, and then press
POWER
G
-
The remote control batteries may be dead. Replace the
batteries or try the control panel buttons.
If you have recently replaced the lamp unit, make sure the
lamp unit and lamp unit door are installed properly
(re" pages 47 49).
The lamp unit may need to be replaced (re" pages 47 49).
Also see "LED indications" (t_¢ page 46).
If the TV is powered off and then quickly on again when
the lamp unit is hot, it may take several minutes for the
picture to appear on-screen. This is a property of DLP TV
lamp technology and is NOT a sign of malfunction. For
details, see IMPORTANT NOTICE ABOUT "HOT
LAMP RESTART" (r_ page 2).
Picture problems
General picture problems
• Check the antenna/cable connections (t_ "hTsmllation
GuMe).
• tS"ess _) on the remote control or INPUT on the TV
control panel and select a valid video input source
(re' page 23). If no device is connected to any of the
inputs on the TV, no picture will display when you select
that particular input source. For device connection
details, see the Installation GuMe.
• Antenna reception may be poor. Use a highly directional
outdoor antenna (if applicable).
• The station may have broadcast difficulties. Try another
channel.
• Adjust the picture qualities (re" page 30).
• If you are using a VCR, make sure T_R on the remote
control is set correctly (rg' page 9).
• If you have two VCRs connected to your TV, make sure
you have not connected the same VCR to the TV's output
and input connections at the same time (_' hTsmllation
Guide).
• Do not connect both a standard video cable and an Svideo cable to the same set of VIDEO inputs (VIDEO t,
or VIDEO 2) at the same time (r_" installation GuMe).
Noisy picture
• If you are watching a tuned analog channel (off-air
broadcast or Cable TV), set the CableClear®/DNR
feature to AUTO to reduce visible interference in the TV
picture (t_
page 41).
Video Input Selection problems
• If the Input Selection
window does not appear when
you press @ on the remote control or INPUT on the TV
control panel, press _) a second time, which will change
to the next video input source and display the Input
Selection
window.
Cannot view external signals or channel 3 or 4
• If you cannot view signals from external devices
connected to VIDEO 1, VIDEO 2, or ColorStream0fi
or from channels 3 or 4, make sure the Input Lock is set
to Off (re" page 38).
Poor color or no color
• The station may have broadcast difficulties. Try another
channel.
• Adjust the Tint and/or Color (r_> page 30).
• When the ColorStream
® signal source is active, the
VIDEO OUT terminal outputs blank video. To receive
video from the VIDEO OUT signal, a standard video or
S-video
IN terminal must be used instead of the
ColorStream 0'_connections.
Picture brightness
changes soon after turning on TV
• If you set the lamp mode to Low Power, each time you
turn on the TV, the lamp will start out in High Bright
mode but will switch to Low Power mode after a short
period of time. You may notice a change in screen
brightness when this happens. This is normal and is not a
sign of malfunction (t_¢"page 42).
Poor composite
or S-video picture
• If the TV is connected to an external A/V device (e.g.,
DVD player, video game system, set-top box, etc.) try
using a ColorStream or HDMI video connection
instead.
Picture and sound are out of sync
• As with all products that contain a digital display, in rare
instances, when viewing certain content (e.g.. television
broadcasts, video games, DVDs), you may notice that the
sound and picture are slightly out of sync. This
phenomenon can be caused by various factors including,
without limitation, video processing within the TV, video
processing in an attached gaming system, and video
processing or different compression rates used by
broadcasters in their programming. You may want to try
one or more of the following suggestions, which may
help to reduce the effect of this phenomenon:
44
HM66 (E/F) Web 213:276
HM66
ENbook
Page 45 Thursday
February 23. 2006 2:49 PM
t
i iii i
_
- If the TV is connected to an A/V receiver that has a
programmable audio delay feature, use this feature
to help synchronize the sound to the picture.
- If you notice this phenomenon only on certain TV
channels, please contact your local broadcast,
cable, or satellite provider to inform them of this
issue.
Sound problems
• Check the antenna/cable connections (_s'r Installation
GuMe).
• The station may have broadcast difficulties. Try another
channel.
• The sound may be muted. Press _.
• If you hear no sound, try setting the MT$ feature to
Stereo mode (r_ page 33).
• Make sure the Speakers function in the Audio Setup
menu is set correctly (t_ _page 34).
• If you are not receiving a second audio program from a
known SAP source, make sure the MT$ feature is set to
SAP mode (_' page 33).
• If you hear audio that seems "incorrect" for the program
you are watching (such as music or a foreign language),
the SAP mode may be on. Set the MT$ feature to Stereo
mode (r<r _page 33).
• When using an external audio amplifier, if you connect
the amplifier to the VAR. AUDIO OUT terminals, the
volume of the TV and amplifier must be set above 0 or
you will not hear any sound (re Installation GuMe).
iiii
Closed caption problems
If the program oz"video you selected is not closedcaptioned, no captions will display on-screen
(re" page 31).
If text is not available, a black rectangle may appear onscreen. If this happens, turn off the closed caption feature
(t_¢ page 31).
A closed caption signal may not display correctly in the
following situations: a) when a videotape has been
dubbed: b) when the signal reception is weak: or c) when
the signal reception is nonstandard (r_ page 31).
Rating blocking (V-Chip) problems
• If you forget your PIN code: While the PIN code entering
screen is displayed, press 0 four times within 5
seconds. The PIN code you previously stored will be
cleared (r_ page 35).
• The V-Chip feature is available for the U.S. V-Chip
system only (_" page 36).
•
•
RECALL
Remote control problems
• Make sure the remote control is set to the correct device
mode (re pages 9-10).
• Remove all obstructions between the remote control and
the TV.
• The remote control batteries may be dead. Replace the
batteries (r_ page 7).
• Your TV remote control may not operate certain features
on your external device. Refer to the owner's manual for
your other device to detennine its available features. If
your TV remote control does not operate a specific
feature on another device, use the remote control that
came with the device (r_' pages 9 13).
• If the TV still does not act as expected, use the Restore
Factory Defaults procedure (r_ page 22).
Channel tuning problems
• Make sure the remote control is set to the correct device
mode (re' page 8).
• The channel may have been erased from the channel
memory by the Channel
Add/Delete
feature. Add the
channel to the channel memory (r_ page 17).
• The channel may be blocked by the Channels
Block
feature. Unblock the channel (re" page 37).
• If you are unable to tune digital channels, check the
antenna configuration (t_¢ page 16). If you are still
unable to tune digital channels, clear all channels from
the channel list (t_¢' page 18) and reprogram channels into
the channel memory (r_ page 17). If you are still unable
to tune digital channels, use the Restore Factory Defaults
procedure (r_ page 22). Also see "TV stops responding
to controls" and "Other problems" (re" page 44).
45
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 46 Thursday
February 23. 2006 2:49 PM
t
i iii i
_
iiii
LEDindications
Tile yellow
blue and red/green
LED lights on tile TV (at tile bottom center of the TV) indicate
tile TV's status, as described
below:
Note: tf the TV loses A/C power (e.g., a power outage occurs or the power cord is unplugged), when power is restored, the yellow
LED will blink while the TV is booting until the remote control is usable. This is normal and is not a sign of malfunction.
TV front
"Voice announce" feature
Iiiil'LAMP
OWER
HI L?__??
B_
YelbwLED BlueLED Red/Green
LED
When certain non-standard conditions occur, the LEDs on
the TV will blink and the TV will play a recorded
"voice announcement" describing the condition (see the
table below for the specific conditions that include a voice
announcement).
To repeat the voice announcement and hear additional
information, press the MENU button on the TV while the
LEDs are blinking.
_i_
The TV is operating
properly.
In LPS mode (standby
with Quick Restart ON).
See "Setting the Quick Restart
The TV will automatically
(see item #4).
The lamp is not working
properly.
TM
feature" (_
page 20).
-
try to restart itself eight times
Note: If the TV is powered off and then quickly on again
when the lamp unit is hot, it may take several minutes
for the picture to appear on-screen. This is a property of
DLP TV lamp technology and is NOT a sign of
malfunction. For details, see "Setting the Quick
Restart TM feature" and "IMPORTANT NOTICE ABOUT
HOT LAMP RESTART" (_. page 21).
4) Yellow is ON
(solid). Red blinks,
The lamp is not working
properly after the eighth
automatic restart (see
item #3).
Turn the TV OFF and then ON again. If the problem
5) Yellow is ON
(solid).
The lamp unit door is not
seated properly.
Turn OFF the TV and unplug the power cord. Review
"Lamp
in Chapter
ensure unit
that replacement
the lamp doorand
is care"
installed
securely,8 to
6) Red blinks.
Fan stopped
(light engine).
"Fan
stopped."
7) Blue is ON (solid).
Green blinks.
Fan stopped (POD).
"Fan
stopped."
8) Blue blinks
Abnormal operation of
BUS line.
slowly.
9) Blue blinks quickly.
Power Protect
Detection.
10)Blue blinks quickly.
Red blinks.
The color wheel has
stopped.
11)Blue blinks quickly.
Yellow blinks.
Red blinks.
An abnormal
temperature increase
has occurred.
"Lamp not
working"
persists,
contact Consume Solutions at
1-800-631-3811.
"Lamp door is
open."
Turn OFF the TV and unplug the power cord. Plug the
power cord in again and turn ON the TV.
"Color wheel
stopped."
Turn OFF the TV. Check to make sure all slots and
openings in the TV cabinet are not covered, blocked, or
dusty. Turn ON the TV again.
"Temperature
warning."
If! after trying solutions, the problem still exists:
• In the U.S., call TACP Consumer Solutions at 1-800-631-3811.
• In Canada, locate the nearest Toshiba authorized service depot by directing your web browser to www.toshiba.ca;
"Home Entertainment," and then click "Support."
click
46
HM66 (E/F) Web 213:276
HM66
ENbook
Page 47 Thursday
February 23. 2006 2:49 PM
t
Lampunit replacementandcare
When to replace the lamp unit
You
the lamp
unit:
and/or colors fade;
• if the screen (lamp) does not light (LED indication
_r_r page 46); or
WARNING:RISK OF ELECTRIC
SHOCK!
TO REDUCE THE RISK OF ELECTRIC
SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS
SPECIFIED HEREIN. REFER ALL SERVICING NOT
SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE
PERSONNEL. Failure to follow this WARNING may result in
death or serious injury.
The light source for this TV is a mercury lamp with internal
atmospheric pressure that increases during use. The lamp has a
limited service life that varies depending on product use and
user settings.
As is generally the case with all projection TVs that use
projection lamps as a light source, the brightness of the lamp
in this TV may vary somewhat over the expected service life
and will generally decrease over time. Because of the many
variables that can affect the useful selwice life of the lamp, your
experience may vary fiom other users.
Note : The lamp is warranted only for the periods and to the
extent set forth in the Limited Warranty applicable to this set.
See "Limited United Sta tes Warranty" (_ page 51) or "Limited
Canada Warranty" (_ page 52), as applicable.
its service
replace
• if the picture darkens
Replacing the lamp unit
(User-replaceable component)
If you use the lamp beyond
should
life:
• you may notice a reduction in the colors and/or brightness of
the picture; and
• the strength of the quartz glass in the lamp will be reduced
and the lamp may rupture (often making a loud noise when
this happens), ffthe lamp ruptures, the TV will not operate
until the lamp unit is replaced.
#4,
• if you hear a loud noise and the picture goes black, which
may indicate a lamp rupture (LED indication
#4,
_ page 46).
To obtain
a replacement
In warranOv
lamp
unit:
Visit www.tacp.toshiba.com/service
call toll-free 1-800-631-3811.
or
Visit www.ceaccessories.toshiba.com
consult your consumer electronics dealer.
or
Locate a Toshiba parts distributor by visiting
www.toshiba.ca. Click "Home Entertainment" and then
click "Support."
Always replace the lamp unit with the model
currently recommended by Toshiba.
For more information, please contact us at the
telephone numbers listed above, or visit the
websites listed above, as applicable.
Using any lamp other than those recommended by
Toshiba may cause damage to the TV and/or lamp.
SUCH DAMAGE IS NOT COVERED UNDER YOUR
TOSHIBA WARRANTY.
CAUTION:Always handle the lamp unit
with care.
The lamp unit in this TV was designed for safe
replacement by consumers; however, if the lamp unit is
subjected to intentional abuse (such as excessive
mechanical abuse or handling by children or pets), the unit
may break, exposing sharp edges or pinch points.
47
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 48 Thursday
Februar,t23.
2006 2:49 PM
t
4
How to replace the lamp unit
Using a manual Phillips screwdriver, loosen tile two
screws on tile lamp unit.
WARNING:RISK OF ELECTRIC
SHOCK!
TO REDUCE THE RISK OF ELECTRIC
SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS
SPECIFIED HEREIN. REFER ALL SERVICING NOT
SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE
PERSONNEL. Failure to fellow this WARNING may result in
death or serious injury.
/
Required
tools:
Lamp unit screws
• Manual screwdrivers (Phillips and slotted)
• Soft, lint-free gloves
1
WARNING:RISK OF ELECTRIC
SHOCK!
Turn off tile TV and unplug tile power cord.
WARNING:Eye damage may result from
directly viewing the light produced by
this lamp.
Always turn off the TV and unplug the power cord before
opening the lamp unit door.
The lamp unit door is provided with an
interlock to reduce the risk of electric shock and excessive
ultraviolet radiation. Never defeat its purpose or attempt
to service without removing the lamp unit door
completely. Failure to follow this WARNING may result in
death or serious injury.
5
2
STOP! Allow the lamp to cool for at least one (1) hour
before replacing
it.
Grasp tile lamp unit handle and gently pull tile lamp unit
straight out of the TV. Set the old lamp unit aside
(_ "Disposing of the used lamp unit" on page 49).
CAUTION:
HOT
SURFACE!
Touching the lamp before it has cooled will result in
severe burns. ALLOW THE LAMP TO COOL FOR AT
LEAST ONE (1) HOUR BEFORE REPLACING IT.
On tile lamp unit door on tile back of the TV, loosen tile
screw by using manual screwdriver, and then remove the
lamp unit door.
TV back
NOTE:
Wear soft, lint-free
replacing the lamp unit.
Lamp unit door detail
6
screw
using manual
screwdriver
gloves when
Carefully insert the new lamp unit straight into the TV
until it is fully seated.
....
j
48
HM66 (E/F) Web 213:276
HM66
ENbook
Page 49 Thursday
February 23. 2006 2:49 PM
t
9
Notes:
• Never subject the lamp unit to excessive shock.
Replace tile screw and tighten using a manual
screwdriver.
° Never touch the lamp unit glass or otherwise get it dirty.
Doing so may affect the image quality and reduce the
service life of the lamp. See "Cleaning the lamp unit glass"
below.
CLEANINGTHE LAMP UNIT GLASS
If you accidentally touch the lamp unit glass or otherwise get
it dirty, wipe it with a lin>free lens cleaning cloth (such as a
cloth for cleaning camera lenses or eyeglasses).
Hand tighten using
manual screwdriver
CAUTION:NEVER clean a hot lamp with any
Lamp unit door
type of flammable liquid or aerosol cleaning
agent. Manyordinary cleaningagents (suchas
glasscleaners) containchemicalsthat may be flammableat
certaintemperatures.If the lamp unit is not allowedto coolfor at
least one (1) hour,such chemicalsmay ignite.
NOTE:
Make sure the lamp unit door is installed
securely; otherwise, the TV may not turn on.
10
7
Using a manual phillips screwdriver, tighten tile two lamp
unit screws.
Note: Hand-tighten
screwdriver.
only. Do not use an electric
Plug in the power cord and turn on the TV. After the initial
warmup period (which may take several seconds for full
picture brightness), the TV should operate normally. If
any of the following conditions exist, turn offthe TV,
unplug the power cord, and repeat steps 1-9 to ensure that
the lamp unit and lamp unit door are installed correctly:
• No pictum
• Dark picture
• TV will not turn on
IL after repeating steps 1-9, the problem still exists:
• In the U.S., call TACP consumer solutions at 1-800631-3811.
S
/
• In Canada, locate the nearest Toshiba authorized
smwice depot by directing your web browser to
www.toshiba.ca;
click "Home Entertainment,"
and
then click "Support."
/
/,
XI:2;"
Lamp unit screws
(use manual Phillips screwdriver only)
Disposingof the used lamp unit
NOTE
: Make sure the lamp unit and screws are
installed securely; otherwise, the TV may not turn
on and the lamp life may be shortened.
8
Reattach the lamp unit door, making sure to insert the
hooks on the left side of the lamp unit door inside the
opening in the TV cabinet.
.......
• Place the used lamp unit in the empty box from the new unit.
• Keep the lamp unit out of reach of children
and pets.
CAUTION:Always handle the lamp unit
with care.
The lamp unit in this TV was designed for safe
replacement by consumers; however, if the lamp unit is
subjected to intentional or accidental abuse (such as
excessive mechanical abuse or handling by children or
pets), the unit may break, exposing sharp edges or pinch
points.
• Dispose of the used lamp unit by the approved method for
your area.
'_STcrt2heeht°°;k2n
innSg
! e the _i
__/.
NOTE : The lamp unit contains mercury.
Lamp unit door
Disposal of mercury may be regulated due to
environmental considerations. For disposal or
recycling information, contact your local
authorities or the Electronic Industries Alliance
(www.eiae.org).
49
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 50 Thursday
February 23. 2006 2:49 PM
t
HDMI TM INPUT:
HDMI compliant (type A connector)
HDCP compliant
E-EDID** compliant
Suggested formats: 1080i, 48%, 480i, 720p
HDMI Audio: 2-channel PCM: 32144.1148 kHz
sampling frequency; 16120124 bits per sample
Specifications
Notes:
• This model complies with the specifications
below.
listed
•
Designs and specifications
without notice.
•
This model may not be compatible with features and/or
specifications that may be added in the future.
Television
are subject to change
System
NTSC standard
ATSC standard (8VSB)
Digital Cable (64 QAM, 256 QAM: in-the-clear,
unencrypted*)
Channel
DIGITAL AUDIO
Optical type
Coverage
50HM66:
56HM66:
50HM66:64
56HM66:72
Operating
Consumption
Speaker
10W
Type
Main:
Tweeter:
Video/Audio
Two 2-318 x 4-314 inches (6x12 cm) round
Two 1-5116 inches (33 ram) round
S-VIDEO INPUT:
Y: 1 V(p-p), 75 ohm, negative sync.
C: 0.286 V(p-p) (burst signal), 75 ohm
VIDEO/AUDIO
INPUT:
1 V(p-p), 75 ohm, negative sync.
150 mV(rms) (30% modulation equivalent,
ohm or greater)
conditions
Optional Stands
50HM66:ST 5066
56HM66:ST 5666
Terminals
VIDEO:
AUDIO:
lbs (29.0 kg)
lbs (32.7 kg)
Supplied Accessories
• Remote control with two size "AAA" batteries
• Dual-wand IR blaster cable
• Installation Guide
• Operating Guide (this book)
Power
10W+
47-3116 inches ( 1,199 ram)
30-11/16 inches (780 ram)
16-5/8 inches (422 ram)
52-3/8 inches (1,330 ram)
33-3/4 inches (857 ram)
18-3/8 inches (467 ram)
Temperature: 41°F 95°F (5°C 35°C)
Humidity: 2080% (no moisture condition)
215 W (average)
28 W ill standby mode (using a CableCARD TM)
24 W ill standby mode (without a CableCARD TM)
Audio
Width:
Height:
Depth:
Width:
Height:
Depth:
Weight
Source
120 V AC, 60 Hz
Power
OUTPUT:
Dimensions
VHF: 2 through 13
UHF: 14 through 69
Cable TV: Mid band (A-8 through A-l, A through I)
Super band (J through W)
Hyper band (AA through ZZ, AAA, BBB)
Ultra band (65 through 94, 100 through 135)
Power
VIDEO/AUDIO
OUTPUT (also for recording):
VIDEO: 1 V(p-p), 75 ohm, negative sync.
AUDIO: 150 mV(rms) (30% modulation equivalent,
2.2 k ohm or less)
VARIABLE AUDIO OUTPUT:
0-300 mV(rms) (30% modulation equivalent, 2.2 k
ohm or less)
Encrypted channels can be viewed on this TV using a
CableCARD. TM (_ Installation Guide).
**
E-EDID = Enhanced-Extended
Display Identification
22 k
ColorStream
® (component video) HD INPUT:
VIDEO:Y: iV(p-p), 75 ohm
PR: 0.7 V(p-p), 75 ohm
PB: 0.7 V(p-p), 75 ohm
Suggested formats: 1080i, 480p, 480i, 720p
AUDIO: 150 mV(rms), 22 k ohm or greater
50
HM66 (E/F) Web 213:276
HM66
ENbook
Page 51 Thursday
February 23. 2006 2:49 PM
t
LimitedUnitedStatesWarranty
for DLPTM Television Models
ToshibaAmerica Consumer Products,L.L.C. ("TACP")makes the
following limited warrantiesto original consumers in the United States.
THESE LIMITEDWARRANTIESEXTENDTO THE ORIGINAL
CONSUMERPURCHASEROR ANY PERSONRECEIVINGTHISDLPTM
TELEVISIONAS A GIFT FROMTHE ORIGINALCONSUMER
PURCHASERAND TO NO OTHER PURCHASEROR TRANSFEREE.
DLPTM TELEVISIONSPURCHASEDIN THE U.S.A.AND USED
ANYWHEREOUTSIDEOF THE U.S.A.,INCLUDING,WITHOUT
LIMITATION,CANADAAND MEXICO,ARE NOT COVEREDBY THESE
WARRANTIES.
DLPTM TELEVISIONSPURCHASEDANYWHEREOUTSIDEOF THE
U.S.A.,INCLUDING,WITHOUTLIMITATION,CANADAAND MEXICO,
AND USEDIN THE U.S.A.,ARE NOT COVERED BYTHESE
WARRANTIES.
Limited One (1) Year Warranty on Parts and Labor
TACP warrants this DLP TM Television and its parts against defects in
materials or workmanship for a period of one (1) year after the date of
original retail purchase. DURING THIS PERIOD, TACP WILL, AT TACP'S
OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR
REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS OR
(1) You must retain your original bill of sale or provide other proof of
purchase.
(2) All warranty servicing of this DLP TM Television must be performed by
an Authorized TACP Service Station.
(3) The warranties from TACP are effective only if this DLPTMTelevision is
purchased and operated in the Continental U.S.A. or Puerto Rico.
(4) Labor service charges for set installation, setup, adjustment of
customer controls, and installation or repair of antenna systems are
not covered by this warranty. Reception problems caused by
inadequate antenna systems, misaligned satellite dishes, cable
television distribution, VCRs, DVD players/recorders, personal
computer level IEEE1394 devices, and any other connected signal
source device are your responsibility.
(5) Warranties extend only to defects in materials or workmanship as
limited above, and do not extend to any DLP TM Television or parts that
have been lost or discarded by you or to damage to the DLP TM
Television or parts caused by fires, misuse, accident, Acts of God
(such as lightning or fluctuations in electric power), improper
installation, improper maintenance, or use in violation of instructions
furnished by TACP; use or malfunction through simultaneous use of
this DLP TM Television and connected equipment; or to units that have
been modified or had the serial number removed, altered, defaced,
or rendered illegible.
How to Obtain Warranty Service
If, after following all of the operating instructions in this manual and
reviewing the section titled "Troubleshooting," you find that service is
needed:
LABOR. During this period, TACP Authorized Service Station personnel
will come to your home when warranty service is required. Depending on
the type of repair required, the service will either be performed in your
home or the DLP TM Television will be taken to a TACP Authorized Service
(1) To find the nearest TACP Authorized Service Station, visit TACP's
website at www.tacp.toshiba.com/service
or contact TACP's
Consumer Solution Center toll free at 1-800-631-3811.
Station for repair and returned to your home at no cost to you.
(2) You must present your original bill of sale or other proof of purchase
to the TACP Authorized Service Station.
Limited One (1) Year Warranty on Lamp Unit
TACP warrants the original lamp unit contained in this DLP TM Television
against defects in materials or workmanship for a period of one (1) year
after the date of original retail purchase. DURING THIS PERIOD, TACP
WILL, AT TACP'S OPTION, EXCHANGE A DEFECTIVE LAMP UNIT
WITH A NEW OR REFURBISHED LAMP UNIT WITHOUT CHARGE TO
YOU. LABOR CHARGES FOR LAMP UNIT REPLACEMENTARE YOUR
RESPONSIBILITY AND ARE NOT COVERED UNDER THIS
WARRANTY. The lamp unit is a user-replaceable
component.
Rental Units
The warranty for DLP TM Television rental units begins on the date of the
first rental or thirty (30) days after the date of shipment to the rental firm,
whichever comes first.
Limited Warranty for Commercial Units
TACP warrants DLP TM Televisions, including the lamp units contained
therein, that are sold and used for commercial purposes as follows: all
parts are warranted against defects in materials or workmanship for a
period of ninety (90) days after the date of original retail purchase.
DURING THIS PERIOD, TACP WILL, AT TACP'S OPTION, REPAIR OR
REPLACE A DEFECTIVE PART WITH A NEW OR REFURBISHED PART
WITHOUT CHARGE TO YOU.
Owner's Manual and Product Registration
Read this owner's manual thoroughly before operating this DLP TM
television.
Complete and mail the enclosed product registration card or register your
DLP TM Television online at www.tacp.toshiba.com/service
as soon
as possible. By registering your DLP TM Television you will enable TACP to
bring you new products specifically designed to meet your needs and
help us to contact you in the unlikely event a safety notification is required
under the Consumer Product Safety Act. Failure to register your product
does not diminish your warranty rights.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING
CONDITIONS:
For additional information, visit TACP's web site:
www.tacp.toshiba.com.
ALL WARRANTIESIMPLIED BY THE LAW OF ANY STATEOF THE
U.S.A.,INCLUDINGTHE IMPLIED WARRANTIESOF
MERCHANTABILITYAND FITNESSFOR A PARTICULARPURPOSE,
ARE EXPRESSLYLIMITEDTO THE DURATIONOF THE LIMITED
WARRANTIESSET FORTHABOVE. WITH THE EXCEPTIONOF ANY
WARRANTIESIMPLIEDBY THE LAWOF ANY STATEOF THE U.S.A.
AS HEREBYLIMITED,THE FOREGOINGWARRANTY IS EXCLUSIVE
AND IN LIEU OF ALL OTHERWARRANTIES,GUARANTEES,
AGREEMENTS,AND SIMILAR OBLIGATIONSOF TACP WITH
RESPECTTO THE REPAIROR REPLACEMENTOF ANY PARTS.IN NO
EVENTSHALLTACP BE LIABLE FOR CONSEQUENTIALOR
INCIDENTALDAMAGES (INCLUDING,BUT NOT LIMITEDTO, LOST
PROFITS,BUSINESSINTERRUPTION,OR MODIFICATIONOR
ERASUREOF RECORDEDDATACAUSEDBY USE, MISUSEOR
INABILITYTO USE THIS DLPTM TELEVISION).
No person,agent,distributor,dealer,or company is authorizedto change,
modify, or extend the terms ofthese warrantiesin anymanner whatsoever.
The time withinwhich an action must be commencedto enforce any
obligation of TACParising underthe warrantyor under any statute or law
of the United Statesor any statethereof is hereby limited to ninety(90)
days from the date you discover, or should have discovered, the defect.
This limitationdoes not apply to impliedwarrantiesarising underthe law
of any state of the U.S.A.
THIS WARRANTYGIVES YOU SPECIFICLEGAL RIGHTSAND YOU
MAYALSO HAVEOTHER RIGHTSWHICH MAY VARY FROMSTATE
TO STATE IN THE U.S.A. SOME STATESOF THE U.S.A. DO NOT
ALLOW LIMITATIONSON THE DURATIONOF AN IMPLIED
WARRANTY,WHENAN ACTION MAYBE BROUGHT,OR THE
EXCLUSIONOR LIMITATIONOF INCIDENTALOR CONSEQUENTIAL
DAMAGES.THEREFORE,THEABOVE PROVISIONSMAYNOTAPPLY
TOYOU UNDERSUCH CIRCUMSTANCES.
05
51
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 52 Thursday
February 23. 2006 2:49 PM
t
Your Responsibility
THE ABOVE WARRANTIESARE SUBJECTTO THE FOLLOWING
CONDITIONS:
Limited Canada Warranty
for DLPTM Television Models
Toshibaof Canada Limited ("TCL") makesthe followinglimited warranties
to original consumers in Canada.
THESE LIMITEDWARRANTIESEXTENDTO THE ORIGINAL
CONSUMERPURCHASEROR ANY PERSONRECEIVINGTHISDLPTM
TELEVISIONAS A GIFT FROMTHE ORIGINALCONSUMER
PURCHASERAND TO NO OTHER PURCHASEROR TRANSFEREE.
PRODUCTSPURCHASEDIN THE U.S.A. AND USED IN CANADAARE
NOT COVEREDBY THESEWARRANTIES.
PRODUCTSPURCHASEDIN CANADAAND USEDIN THE U.S.A.ARE
NOT COVEREDBY THESEWARRANTIES.
Limited One (1) Year Warranty on Parts and Labor*
TCL warrants this DLP TM television television and its parts against defects
in materials or workmanship for a period of one (1) year after the date of
original retail purchase. DURING THIS PERIOD, TCL WILL, AT TCL'S
OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR
REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS OR
LABOR. TCL Authorized Service Depot personnel will come to your home
when warranty service is required. Depending on the type of repair
required, either the service will be performed in your home or the set will
be taken to the TCL Authorized Service Depot for repair and returned to
your home at no cost to you. IN-HOME SERVICE ONLY APPLIES WITHIN
100 KILOMETERS OF AN AUTHORIZED TCL SERVICE DEPOT.
Limited One (1) Year Warranty on Lamp Unit*
TCL warrants the lamp unit in this DLP TM television against defects in
materials or workmanship for a period of one (1) year after the date of
original retail purchase. DURING THIS PERIOD, TCL WILL, AT TCL'S
OPTION, EXCHANGE A DEFECTIVE LAMP UNIT WITH A NEW OR
REFURBISHED LAMP UNIT WITHOUT CHARGE TO YOU. LABOR
CHARGES FOR LAMP UNIT REPLACEMENT ARE NOT COVERED
UNDER WARRANTY. The lamp unit is a user-replaceable
component.
Rental Units
The warranty for rental units, including the lamp units contained therein,
begins with the date of first rental or thirty (30) days from the date of
shipment to the rental firm, whichever comes first.
*Limited Warranty for Commercial Units
TCL warrants DLP TM televisions, including the lamp units contained
therein, sold and used for commercial purposes as follows: all parts are
warranted against defects in materials or workmanship for a period of
ninety (90) days after the date of original purchase. DURING THIS
PERIOD, TCL WILL, AT TCL'S OPTION, REPAIR OR REPLACE A
DEFECTIVE PART WITH A NEW OR REFURBISHED PART WITHOUT
CHARGE TO YOU. ON-SITE SERVICE ONLY APPLIES WITHIN 100
KILOMETERS OF AN AUTHORIZED TCL SERVICE DEPOT.
Owner's Manual and Product Registration
Read this owner's manual thoroughly before operating this DLP TM
television.
Register your product online at www.toshiba.ca
as soon as possible.
By registering your product you will enable TCL bring you new products
specifically designed to meet your needs and help us to contact you in the
unlikely event a safety notification is required under the Consumer
Product Safety Act. Failure to register your product does not diminish your
warranty rights.
(1) You must provide your bill of sale or other proof of purchase.
(2) All warranty servicing of this DLP TM television must be performed by
an Authorized TCL Service Depot.
(3) These warranties from TCL are effective only if the DLpTMtelevision is
purchased in Canada from an authorized TCL dealer and operated in
Canada.
(4) Labor charges for installation, setup, adjustment of customer
controls, and installation or repair of antenna systems are not covered
by these warranties. Reception problems caused by inadequate
antenna systems are your responsibility.
(5) Warranties extend only to defects in materials or workmanship as
limited above, and do not extend to any DLP TM television or parts that
have been lost or discarded by you or to damage to the television or
parts caused by fires, misuse, accident, Acts of God (such as
lightning or fluctuations in electric power), improper installation,
improper maintenance, or use in violation of instructions furnished by
TCL; use or malfunction through simultaneous use of this product and
connected equipment; or to units that have been modified or had the
serial number removed, altered, defaced, or rendered illegible.
How to Obtain Warranty Services
If, after following all of the operating instructions in this manual and
checking the "Troubleshooting" section, you find that service is needed:
(1) To find the nearest TCL Authorized Service Depot, visit TCL's web site
at www.tos h i ba. ca.
(2) Present your bill of sale or other proof of purchase to the Authorized
Service Depot.
For additional information, visit TCL's web site:
www.toshiba.ca
ALL WARRANTIESIMPLIED BY THE LAW OF ANY PROVINCEOF
CANADA, INCLUDINGTHE IMPLIEDWARRANTIESOF
MERCHANTABILITYAND FITNESSFOR A PARTICULARPURPOSE,
ARE EXPRESSLYLIMITEDTO THE DURATIONOF THE LIMITED
WARRANTIESSET FORTHABOVE. WITH THE EXCEPTIONOF ANY
WARRANTIESIMPLIEDBY THE LAWOF ANY PROVINCEOF CANADA
AS HEREBYLIMITED,THE FOREGOINGWARRANTY IS EXCLUSIVE
AND IN LIEU OF ALL OTHERWARRANTIES,GUARANTEES,
AGREEMENTS,AND SIMILAROBLIGATIONSOF TCL WITH RESPECT
TO THE REPAIROR REPLACEMENTOF ANY PARTS. IN NO EVENT
SHALLTCL BE LIABLE FOR CONSEQUENTIALOR INCIDENTAL
DAMAGES(INCLUDING,BUT NOT LIMITEDTO, LOST PROFITS,
BUSINESSINTERRUPTION,OR MODIFICATIONOR ERASUREOF
RECORDEDDATACAUSEDBY USE, MISUSE,OR INABILITYTO USE
THIS PRODUCT).
No person,agent,distributor,dealer,or company is authorizedto change,
modify, or extend the terms ofthese warrantiesin anymanner whatsoever.
The time withinwhich action must be commenced to enforce any
obligation of TCL arising under this warrantyor under any law of Canada
or of any province thereof is hereby limited to 90 days from the date you
discover, or should havediscovered, the defect. This limitationdoes not
apply to impliedwarranties arising underthe law of any provinceof
Canada.
THIS WARRANTYGIVES YOU SPECIFICLEGAL RIGHTS,AND YOU
MAYALSO HAVEOTHER RIGHTS,WHICH MAY VARY FROM
PROVINCETO PROVINCEIN CANADA.SOME PROVINCESOF
CANADADO NOT ALLOW LIMITATIONSON THE DURATIONOF AN
IMPLIEDWARRANTY,LIMITATIONSON THE TIME WITHINWHICH AN
ACTIONMAYBE BROUGHT,OR THE EXCLUSIONOR LIMITATIONOF
INCIDENTALOR CONSEQUENTIALDAMAGES;THEREFORE,THE
ABOVE LIMITATIONSOR EXCLUSIONSMAY NOTAPPLY TO YOU
UNDERSUCHCIRCUMSTANCES.
52
HM66 (E/F) Web 213:276
HM66
ENbook
Page 53 Thursday
Februar,,'23.
2006 2:49 PM
t
A copy of the GPL source code in this product may be obtained by
contacting Toshiba Consumer Solutions at (800)631-3811. There will be
a charge to cover the costs of providing the source code.
A copy of the LGPL source code in this product may be obtained by
contacting Toshiba Consumer Solutions at (800)631-3811. There will be
a charge to cover the costs of providing the source code.
USB Protocol Copyright © 2005 The NetBSD Foundation, Inc. All rights
reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
(1) Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
(2) Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
(3) Neither the name of The NetBSD Foundation nor the names of its
contributors may be used to endorse or promote products derived
from this software without specified prior written permission.
THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC.
AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
This product includes software developed by the OpenSSL Project for use
in the OpenSSL Toolkit (http://www.openssl.org).
This product includes cryptographic
(eay@cryptsoft.com).
software written by Eric Young
OpenSSL 0.9.7d Copyright © 1998-2000 the OpenSSL Project. All Rights
reserved. Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the following conditions
are met:
(1) Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
(2) Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
(3) All advertising materials mentioning features or use of this software
must display the following acknowledgement: This product includes
software developed by the OpenSSL Project for use in the OpenSSL
Toolkit (http://openssl.org).
(4) The names "OpenSSL Toolkit" and "Open SSL Project" must not be
used to endorse or promote products derived from this software
without prior written permission. For written permission, please
contact openssl-core@openssl.org.
(5) Products derived from this software may not be called "OpenSSL" nor
may "Open SSL" appear in their names without prior written
permission of the OpenSSL Project.
(6) Redistributions of any form whatsoever must retain the following
acknowledgement: "This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit (http://
www.openssl.org)."
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS"
AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product
includes cryptographic software written by Eric Young
(eay@cryptsoft.com). This product includes software written by Tim
Hudson (tjh @cryptsoft.com).
Copyright © 1995-1998 Eric Young (eay@cryptsoft.com). All Rights
reserved. This package is an SSL implementation written by Eric Young
(eay@cryptsoft.com). The implementation was written so as to conform
with Netscapes SSL. This library is free for commercial and noncommercial use so long as the following conditions are adhered to. The
following conditions apply to all code found in this distribution, be it the
RC4, RSA, Ihash, DES, etc., code; not just the SSL code. The SSL
documentation included with this distribution is covered by the same
copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com).
Copyright remains Eric Young's, and as such any Copyright notices in
the code are not to be removed. If this package is used in a product, Eric
Young should be given attribution as the author of the parts of the library
used. This can be in the form of a textual message at program startup
or in documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
(1) Redistributions of source code must retain the copyright notice, this
list of conditions and the following disclaimer.
(2) Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
(3) All advertising materials mentioning features or use of this software
must display the following acknowledgement: "This product includes
cryptographic software written by Eric Young (eay@cryptsoft.com)."
The word 'cryptographic' can be left out if the routines from the library
being used are not cryptographic related.
(4) If you include any Windows specific code (or derivative thereof) from
the apps directory (application code) you must include an
acknowledgement: "This product includes software written by Tim
Hudson (tjh@cryptosoft.com)."
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE. The license and distribution terms for any publicly available
version or derivative of this code cannot be changed, i.e. this code cannot
simply be copied and put under another distribution license (including the
GNU Public License).
53
HM66 (E/F) Web 213:27(
HM66
ENbook
Page 54 Thursday
Februar,,'23.
2006 2:49 PM
t
A
S
L
Labeling video input ........................
23
SAP sound .....................................
33
Audio quality adjustments ............... 33
Lamp mode ....................................
42
Scroll settings .................................
28
Auto aspect ....................................
29
Lamp unit replacement ....................
47
Selecting Menu Language ............... 16
Auto power off ................................
40
Language selection .........................
16
Side panel control .............................
Antenna input configuration
............ 16
B
Back of the TV ..................................
6
Blocking channels ..........................
37
C
CableClear DNR ............................
41
CH RTN button ...............................
26
CH A v buttons ..............................
26
Channel Browser Setup ..................
Channel Browser TM ........................
24
24
Channel Browser
TM
banner ............. 25
Channel Number buttons ................
26
Channel programming
Automatic programming ........... 17
Manually adding and deleting... 17
Sleep timer .....................................
39
Speaker On/Off ...............................
34
LOCKS menu
Channels, blocking ...................
Enable rating blocking ..............
New PIN code ..........................
Panel lock ................................
Unlocking programs
temporarily .................
Video inputs, locking ................
Specifications .................................
StableSound ® .................................
50
34
Stereo sound ..................................
33
Surf Lock TM ......................................
26
System status .................................
22
Locks menu ....................................
37
36
35
39
38
38
35
41
MTS feature ...................................
33
MUTE button ..................................
32
O
Closed captions ..............................
31
Optical audio output format ............. 34
Color temperature ..........................
ColorStream HD audio ....................
42
P
Digital audio selector ......................
32
Picture quality .................................
Picture scroll ...................................
Digital signal meter .........................
30
30
30
28
21
Picture size selection ......................
27
DNR (Digital Noise Reduction) ........ 41
POWER button .................................
5
Dynamic contrast ............................
Q
41
F
Quick Restart
Favorite channels ...........................
18
Features, TV ....................................
Front of the TV .................................
4
5
H
HDMI audio mode ..........................
20
I
INPUT button .................................
23
Installation, setup .............................
4
Integrated digital tuning ....................
4
..............................
44
V-Chip blocking (Locks menu) ......... 35
Video input label .............................
23
Video input lock ..............................
38
W
Picture adjustment ..........................
Picture mode ..................................
Defaults, restore TV factory ............ 22
TheaterWide ® picture size ............... 27
V
MPEG noise reduction ....................
29
B
T
Troubleshooting
M
Cinema mode .................................
20
5
Last mode memory feature ............. 40
LED indications ...............................
46
..............................
20
RECALL button ..............................
40
TM
Warranty
Canada ....................................
U.S ..........................................
52
51
WOW:SRS 3D ................................
43
WOW:SRS Focus ...........................
43
WOW:SRS TruBass ........................
43
R
Remote control
Battery installation ...................... 7
Device code table .................... 12
Effective range ........................... 7
Functional key chart ................. 10
Learning about the buttons ......... 8
Programming ........................... 11
54
HM66 (E/F) Web 213:276
HM66
ENbook
Page 56 Thursday
February 23. 2006 2:49 PM
t
TOSHIBA
AMERICA
CONSUMER
PROOUCTS,
L.L.C.
CorporateHeadquarters:82 TOTOWAROAD,WAYNE,NJ 07470,U.S.A.
NATIONAL
SERVICE
DIVISION:1420-BTOSHIBADRIVE,LEBANON,TN37087,U.S.A.
TOSHIBA
OF
CANAOA
LTO.
HEAD OFFICE: 191 McNABB STREET,MARKHAM, ONTARIO, L3R 8H2, CANADA - TEL: (905) 470-5400
SERVICECENTERS:
TORONTO: 191 McNABB STREET,MARKHAM, ONTARIO L3R 8H2, CANADA - TEL: (905) 470- 5400
MONTREAL: 18050 TRANS CANADA, KIRKLAND, QUEBEC, H9J 4A1, CANADA - TEL: (514) 390-7766
VANCOUVER:22171 FRASERWOODWAY,RICHMOND, B.C., V6W 1J5, CANADA TEL: (604) 303-2500
MANUFACTUREDBY
TOSHIBA
AMERICA
CONSUMER
PROOUCTS,
L,L,C,
CableClear, ColorStream, StableSound, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.LC.
Channel Browser, SurfLock, and Quick Restart are trademarks of Toshiba America Consumer Products, LL.C.
Digital Light Processing TM , DLPTM and the DLPTM medallion are trademarks of Texas Instruments.
PRINTED
(06-03)
IN USA
rOSHIBA
HM66 (E/F) Web 213:276
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising