zx30 user instructions - Sanji Security Systems

zx30 user instructions - Sanji Security Systems
ZX30 USER INSTRUCTIONS
REV5
Briefed with the idea of “The Super intelligent Design
Concept” Sanji engineers developed the ZX30 alarm
system. The ZX30 represents the 'state of the art' in
vehicle security. Read these instructions for correct
system operation. All points marked
are optional
features.
To enable the Press the lock button
1) SETTING THE
ALARM
on the vehicles remote,
full alarm
the unit will sound 2
features.
soft chirps. The alarm
will be set.
7) VIOLATION
CHIRPS
To indicate to
the user that
the alarm has
triggered in
his/her
absence.
When the alarm is
reset, the unit will
sound 4 loud chirps
if the alarm had
triggered during the
alarm set mode.
8) DOOR LOCK
ON START
Automatic
locking of all
doors when
ignition is
turned on.
When the ignition is
turned on, if all the
doors, boot and
bonnet are closed,
the doors will lock.
9) ONE EVENT
OVERRIDE
To override
the alarm, in
the event of
a flat remote
battery.
Open the door, the
alarm will start to
sound the siren.
Turn the Ignition on
unit chirps once, the
system will be reset.
This is a once off
override.
10) PERMANENT
SERVICE
MODE
To disable
the alarm
permanently.
In drive, (ignition on),
press the hidden
override button for
+- 5sec, the siren
will chirp 4 times.
Permanent override
has been activated.
The dash led will be
on and all alarm,
*
sensor on
2) DOOR / BOOT / To warn the
BONNET OPEN driver that a
WARNING
door or boot
is open when
setting the
alarm.
The unit will sound 2
additional loud chirps
and flash the
indicators twice when
setting the alarm. If a
door is still open when
the unit fully arms, the
doors will be
bypassed. The system
will assume a faulty
door switch.
The dash led will flash
3) ALARM DELAY 15 second
PERIOD
arming delay. rapidly during the
15 sec delay period.
dash led
flashing
After the delay, the
rapidly
dash led dash led will start to
fully
flashing
armed
slowly
flash slowly. The
alarm is now fully
armed.
4) SENSOR SHUT To disable
DOWN
the interior
sensor so
that a pet
or person
can remain
inside the
vehicle when
the alarm
is set.
5) RESETTING
THE ALARM
6) AUTO ZONE
BYPASS
To reset the
alarm.
Automatically
bypass a
defective
zone.
*
service mode ON
5sec
Set the alarm and
wave your hand in
front of the sensor.
The siren will sound
4 chirps. The sensor
has now been
disabled. When the
alarm is set the
sensor will be
disabled. When you
set the alarm again
the sensor will be
armed.
Press the unlock
button on the
vehicles remote.
The unit will
sound 1 soft chirp
and the doors will
unlock. The alarm
has now been reset.
If the unit detects a
permanently faulty
zone, e.g. door or
sensor during alarm
set, the system will
sound 3 times then
isolate the faulty
zone.
service mode
warning
service mode OFF
5sec
11) FORCED
HI-JACK
MODE
*
Forced
hi-jack
option.
immobilizer and
hi-jack features will
be DISABLED. When
the ignition is turned
on the unit will flash
the indicators rapidly
for 4 sec to warn the
user that the unit is
in service mode.
To exit service mode,
turn the ignition on
and press the hidden
override button for
+- 5sec, the siren
will chirp twice.
Permanent override
will be deactivated.
The dash led will turn
off. The system will be
fully functional again.
When you start the
vehicle, the unit will
enter hi-jack, the dash
led will give a 1 second
pulse. Refer to point
16 to reset hi-jack. If
you start the vehicle
with the hidden button
pressed, the unit will
not enter forced
hi-jack.
PG 1
12) DRIVER’S
DOOR
HI-JACK
To activate
hi-jack.
*
13) HI-JACK
OPERATION
*
14) HI-JACK
WARNING
PERIOD
In drive open then
close driver’s door. If
all doors, bonnet and
boot are closed the
dash led will give a
1 second pulse. The
unit has entered
hi-jack delay.
Hi-jack mode. Countdown period is
90 sec. If ignition is
turned off during this
time, the timer will
stop. When the
ignition is turned on
again the timer will
continue. If you try to
set or reset the alarm
during the countdown
period, the unit will
sound 4 loud chirps
to warn you that you
are in hi-jack mode.
Hi-jack
warning
mode.
*
After the countdown
period the unit will
enter the 20 second
warning period. The
unit will chirp and
flash the indicators.
After this period the
unit will enter the 8
second slow down
period. At any point
in time you can reset
hi-jack by pressing
the hidden button.
15) FINAL
HI-JACK
*
16) RESETTING
HI-JACK
*
To confirm
what phase
the unit is in.
In final hi-jack the
siren will sound on
and off at 5 second
intervals and the
indicators will flash.
The immobilizer will
be armed. The unit
can be reset by
pushing the hidden
button for 3 seconds.
To reset the
unit back to
normal drive
mode.
Press the hidden
push button at any
time for 2 seconds,
the unit will chirp
once to confirm that
hi-jack has been
reset.
PG 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising