Classic Model Manual

Classic Model Manual
Adjustable Base - Classic Model
OWNER’S MANUAL
The Sealy Posturematic® Adjustable base is designed to be used
in conjunction withthe Sealy Optimum® mattress.
The Sealy Posturematic® Adjustable Base -Classic
Model Number:
SEALY-AU-SPEC-7937
Reference Codes:
Queen: SA-ABF-A18-N6S220-W-SRB-9V2-110-(20301525M)
Single XL: SA-ABF-A18-N6S220-W-SRB-9V2-110-(2030915M)
1
Safety Precautions
ATTENTION!
IMPORTANT SAFETY INSTRUCTIONS.
PLEASE READ THESE INSTRUCTIONS
NOTE:
Unauthorised modifications to this product could
void the electrical portion of your warranty.
THOROUGHLY BEFORE USING
H O S P I TA L D I S C L A I M E R :
THIS PRODUCT.
NOTE :
ELECTRICAL SAFETY
For optimal safety, it is recommended that your
Adjustable Base is plugged into a surge protector (not
supplied with this Adjustable Base).
Always unplug this Adjustable Base from
the electrical outlet before any cleaning or
maintenance of the bed frame. To safely
position, then remove the plug from the outlet.
Keep cord away from heated surfaces. Keep air
openings free of lint, hair and the like — never
operate when air openings are blocked. Never
drop or insert any object into any opening.
Use only indoors.
Cease use of this bed frame and contact
a qualified service centre for repair if:
• It has a damaged cord or plug
• It is not working properly
• It has been dropped or damaged
This Adjustable Base is designed exclusively for
in-home use.
WARR A N T Y WAR NING!
This Adjustable Base is specifically designed to
require no maintenance by you, the user. Any
opening or tampering with the control box,
motors or hand controls (with the exception of
the battery compartment, if equipped) will
result in a void of the warranty. Only those
authorised may conduct repairs or part
replacement on your Adjustable Base.
It is NOT designed for hospital use and is NOT
designed to meet hospital standards. Do not use this
bed with TENT TYPE oxygen therapy equipment or
use near explosive gases.
I M P O R TA N T S A F E T Y F E AT U R E S
Weight Fail Safe Feature — In the case that an
overload of weight is placed on the head or foot
mechanism, the control unit will automatically
stop all functions. The control unit will
automatically resume all functions 30 seconds
after excess weight is removed.
NOTE:
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
• It has been dropped into water
NOTE:
Children should be supervised to ensure that they
do not play with the appliance.
2
CONSUME R S W I T H PACE M AK E R S
P R O D U C T R AT I N G S
It is possible that the (optional) vibrating feature
of this bed may be interpreted falsely by some
pacemakers as movement and/or exercise. This
is common with any product that produces a
Lift Motor Restrictions — The lift motors in this
bed are NOT designed to operate continuously
for more than 3 minutes over a 30 minute time
period, or approximately 10% duty cycle. To
ensure reliable functionality and full life of this
product, do not attempt to exceed these limits.
pacemaker. Please consult your physician with
any concerns.
SMALL CHILDREN AND PETS
WAR NING
Immediately dispose of all packing materials
as it can pose a smother risk to small children
and pets. Injury could occur also if children or
pets are permitted to play on or under the bed.
Do not allow children to operate this bed without
adult supervision.
NOTE:
Attempting to circumvent or exceed this rating will
shorten the life expectancy of the product and may
void the warranty.
Weight Restrictions — The recommended weight
limits on our Adjustable Bases are:
S AV E T H E SE I NS T RUC T IONS!
Proper operation of your Adjustable Base is
necessary to ensure the long life and durability
you expect from a high-quality product. The
manufacturer has tested and inspected this
product prior to shipment.
• Single Extra long:261kg
• Queen: 295kg
The structure of the bed will support the
recommended weight when distributed
evenly across the bed. Maximum weight the
bed can support per person is 113kg.
The head and foot sections are not designed
to individually support or lift this amount
of weight. For optimal performance, entering
and exiting the Adjustable Base with the bed in
the flat or level position is recommended.
NOTE:
Exceeding the recommended weight restrictions
could damage your Adjustable Base and void
your warranty.
3
Parts List
Before discarding any packing materials,
check the Adjustable Base carton
and verify all items in the parts list
are included.
( B ) MATTRESS RETAINER BRACKET (1)*
( A ) REMOTE CONTROL (1)
( C ) BED LEG (4)
( D) 2 x AA BATTERIES, 2 x 9V BATTERIES
* Indicates part is attached to base for shipping purposes.
4
Optional.
Head Bracket
Headboard
Kit (soldBracket
separately)
Kit
( D ) INNER HEADBOARD BRACKET (2)
(G) 8mm WASHER (12)
( I ) ALLEN KEY WRENCH (1)
( E ) OUTER HEADBOARD BRACKET (2)
(H) 8mm NUT (6)
(J) WRENCH (1)
( F ) HEADBOARD BRACKET BOLT (6)
** To
order thepart
Head
Kitto
please
Sealy Customer
Indicates
is Bracket
attached
basecontact
for shipping
purposes.Support, 1300 130 221.
5
Installation Guide
STEP 1
For safety reasons, the following should be
performed by 2 people. Carefully lift the bed
frame unit out of the shipping carton with the
top side facing downward.
STEP 2: ASSEMBLE THE BED LEGS
For this step, you will need 4 bed legs (C), which
can be found in the accessories box. Turn each
bed leg (C) in a clockwise direction into the
threaded holes on the frame as shown. Repeat
the bed leg assembly for all 4 legs (C) provided.
STEP 4
STEP 8
Return bed to flat or level position.
STEP 5
S T E P 9 : ATTACHING THE ‘QUICK-SET’
Carefully rotate the base frame over so the top side
is facing upward.
MATTRESS RETAINER BRACKET
NOTE:
Be careful not to rest the frame on its side. The weight
may damage the legs.
Fasten the ‘Quick-Set’ mattress retainer bracket
(B) to the foot of the bed base using the
‘Quick-Set’ slide method illustrated below.
Simply position the open ends of the Retainer
Bracket directly aligned with the ‘Loop’ Retainer
Anchors already installed to the foot of the base
surface. Slide the Retainer Bracket forward
allowing the open ends to glide into the loop.
STEP 6
Plug the power cord into a grounded
electrical outlet.
NOTE:
For optimal safety, it is recommended that your
Adjustable Base is plugged into a surge protector (not
supplied with this Adjustable Base).
DO NOT OVERTIGHTEN THE BED LEGS
STEP 7
STEP 3
Install batteries in remote control.
Remove and extend the power cord from
the frame.
Test all functions on the remote control to
ensure all features are operational.
IMPORTANT!
If the bed does not work, refer to
Troubleshooting on page 12.
MAKE SURE POWER CORDS DO NOT OBSTRUCT
ANY ADJUSTABLE BASE MECHANISMS.
6
NOTE:
If a headboard is to be installed, owners who have
purchased the optional Headboard Bracket Kit
continue on to step 10. If the Adjustable Base is to
be set up without a headboard, proceed to step 11.
IMPORTANT!
FAILURE TO FOLLOW THE INSTALLATION STEPS
AS THEY APPEAR IN THIS GUIDE COULD RESULT IN
DAMAGE TO YOUR ADJUSTABLE BASE.
MAKE SURE TO POSITION THE BOTTOM OF THE
HEADBOARD CROSS MEMBER NO MORE THAN
AND THE TOP OF THE MATTRESS.
STEP 10: ASSEMBLE THE HEADBOARD
B
E
Place the open side of the outer headboard
bracket (E) onto the exposed square tube of the
inner headboard bracket (D) to create a tight fit
between (D) and (E). Insert a retainer bolt (G)
fitted with a 8mm washer (I) into the outer
headboard bracket (E) and through the inner
headboard bracket (D). Hand tighten using a
8mm washer (I) and a 8mm nut (J).
(Leave loose enough for adjusting.) Repeat on
the other side.
Measure the distance from the centre of one
mounting hole in the headboard to the centre of
the other.
Measure the distance from the center of one
mounting hole in the headboard bracket
assembly to the centre of the other.
G
If you need to adjust the headboard brackets,
unscrew the bolts holding the outer headboard
brackets and move them the necessary distance.
Reinstall the bolts and securely tighten.
Use the hand control to elevate the head of the
bed so the bed base frame is reachable.
A
Slide the inner headboard bracket (D) horizontally
with the “C” opening facing down under the
crossbar. Position the bracket (D) in the guide peg
on the bottom of the crossbar. Insert a headboard
bolt (G) fitted with a 8mm washer (I) through
the pre-drilled hole in the crossbar and into the
pre-drilled slotted hole in the “C” channel inner
headboard bracket. Tighten in place with a
8mm washer (I) and 8mm nut (J). Repeat
on the other side.
F
STEP 11
Place your mattress on the Adjustable Base
surface. Installation is now complete.
C
If the bed comes with a programming option,
turn to Programming the Remote Control on
page 10 to proceed.
When headboard brackets are assembled, make
sure there is a space of 38.1 to 50.8 mm
between the edge of the bed base and
the headboard brackets.
D
Securely fasten the headboard bolts (not included
with your Adjustable Base) to the end of the
headboard bracket assembly.
7
Using the Remote Control
LED Signature Light
A: Raises the Head
of the Bed
C: Raises the Foot
of the Bed
ADJUSTMENTS (A ,B ,C ,D)
B: Lowers the Head
of the Bed
D: Lowers the Foot
of the Bed
F: Pre-Programmed
Memory Positions
E: Returns Head and
Foot to Flat Position
(hold 3 seconds)
HEAD
AND
FOOT
POSITION
Use to raise or lower the head and foot sections of
your Adjustable Base. The premium “Wall-Glide”
feature will automatically synchronize with all head
and foot adjustments.
BED 'FLAT' BUTTON (E)
Press down and hold for 3 seconds to return bed to
the flat position.
PRE-PROGRAMMED MEMORY
POSITION (F)
These 3 program function keys allow you to select the
most popular positions with 1 touch.
IMPORTANT!
FOR YOUR SAFETY, READ THE OWNER’S MANUAL CAREFULLY AND COMPLETELY BEFORE OPERATING THIS
PRODUCT. ELECTRIC SHOCK MAY OCCUR IF ELECTRICAL COMPONENTS ARE NOT INSTALLED OR OPERATED
ACCORDING TO THESE GUIDELINES.
8
R E M O T E F E AT U R E S
NOTE :
This bed may show minor intermittent performance
because of typical RF interference. This is normal in
the operation of the bed, not a defect.
• The buttons are backlit, when a button is
pressed, to aid in the visibility of the remote
in low light environments.
• It is not necessary to face the receiver to
operate the remote control. Remote signal is
best transmitted within 3 metres of
the receiver.
SAFETY
• In the case that an overload of weight is placed
on the head or foot mechanism, the control
unit will automatically stop all functions.
The control unit will automatically resume
all functions 30 seconds after excess weight
is removed.
• The input transformer voltage is AC240V 50HZ,
the output voltage is DC24V 3A. In the case
of a short-circuit, a fuse on the transformer will
blow to protect the electrical equipment
(Fuse: 1A~1.5A). Should this occur, you MUST
seek professional assistance to replace the fuse.
Call Customer Care at: 1300 130 221
NOTE :
The changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate
the equipment.
9
Programming the Remote Control
NOTE:
Programming by the user is only needed on
replacement remotes, or when controlling two bases
from one remote control.
STEP 1
Insert batteries into the remote control
(2 x AA batteries).
Follow steps 1 through 6 below to use the remote control with 1 power base.
To use the remote control with 2 power bases, repeat the steps for the second power
base using the same remote.
STEP 4
STEP 6
The LED signature light will flash.
This means the RF frequency code setting
function has been activated.
When the receiver light flashes and then
remains illuminated, the RF frequency code
learning process is complete.
STEP 2
Make sure your Adjustable Base is plugged into
a working grounded outlet or surge protector.
STEP 3
STEP 5
Illuminated. Hold down the “Learn” button for
3 seconds to initiate the RF learning mode.
Press any button on the remote control.
10
Lowering the Bed in a Power Outage
Your Adjustable Base is equipped with an emergency lowering feature.
Follow the steps below in the event that your base is in the raised position during
a power outage.
STEP 1
STEP 3
Locate and remove the 9 volt battery cover.
Replace the battery cover.
STEP 2
STEP 4
Install 2 alkaline 9 volt batteries
Press either the “Flat” button (F) or the
individual lowering buttons (C, E) to lower
your bed to the level position.
NOTE:
The 2 alkaline 9 volt batteries are only rated for
single use. Replace every 12 months and after
emergency lowering.
11
Troubleshooting
In the event the Adjustable Base fails to operate, investigate the problems and possible solutions provided below.
REMOTE CONTROL LED
I L L U M I N AT E S A N D A P P E A R S
NORMAL, BUT WILL NOT
O P E R AT E B E D
1 Is the power cord plugged into a working and
grounded electrical outlet?
REMOTE CONTROL FUNCTION
K E Y S W I L L N O T I L L U M I N AT E
1 Replace batteries in the remote control.
2 Check that batteries are installed properly.
NOTE:
HEAD OR FOOT SECTION
F U N C T I O N K E Y W I L L E L E VAT E
BED, BUT WILL NOT RETURN
A grounded, electrical surge protection device is
recommended (not supplied).
POSITION
2 Test outlet by plugging in an appliance you
know works properly.
1 Your bed may be obstructed preventing
smooth operation. Remove obstructions from
around and under the bed.
3 Check low amp fuse on the control box under
bed. Replace fuse if blown.
2 Check that head section has clearance from
headboard or wall.
NONE OF THE FUNCTIONS ON THE
A D J U S TA B L E B A S E W I L L O P E R AT E
3 Headboard may be too close the edge
of the mattresses. Verify a 38 to 50 mm
distance between headboard brackets
and mattress. Adjust if required.
1 Re-program the remote control (as indicated
in the Manual provided with this product, for
programming procedures).
2 Unplug the power cord. After 45 seconds, plug
in to electrical outlet. This should reset the
electronic components.
3 The home electrical circuit breaker may have
been tripped. Reset circuit breaker if needed.
4 Check surge protection device or electrical
outlet to insure working order. Test outlet by
plugging in a known working appliance.
5 Check low amp fuse on control box under bed.
Replace fuse if blown.
12
A C T I VAT I N G H E A D O R F O O T L I F T
FUNCTION CAUSES “PULSING”
OR “STUTTERING” WHEN
O P E R AT I N G F E AT U R E
1 Check batteries and installation in remote.
2 Assure that the function key is pressed directly
and firmly.
3 Radio frequency interference from other
normal operation.
Tie Strap Installation for Split Adjustable Base Systems
While using a split system, it is important to
adhere to the following installation instructions.
Proper use of the included tie straps will securely
hold split King adjustable bases together.
STEP 1
STEP 4
Complete the installation of two bases
side-by-side according to the Complete
Reference Guide provided with your foundation.
It is recommended that the gap between bases
be no more than 25mm.
While one installer carefully lifts the left side of
the base, the other installer slips the other side of
the elastic and strap around the suspended left
leg of the base. Carefully lower the base.
STEP 2
Locate the two (2) looped straps (one (1) included
with each split King base).
STEP 3
INSTALLATION INSTRUCTIONS
FOR ADJUSTABLE BASE TIE STRAPS
WARNING: For safety reasons, it is recommended
that two people perform installation.
NOTE:
One (1) looped strap is included with each split
King adjustable base .
Start with one (1) strap at either the head or foot
of the bed. While one installer carefully lifts the
right side of the base, the other installer slips both
the elastic and strap loops around the suspended
right leg of the base. Carefully lower the base.
NOTE:
The elastic loop must be at top of strap
when fitted around leg.
STEP 5
With the elastic loop above the strap, slide both
as high as they will go to the top of each leg.
Place the elastic loop up and over the notch at
the top of the leg.
NOTE:
STEP 4
While one installer carefully lifts the left side of
the base, the other installer slips the other side of
the elastic and strap around the suspended left
leg of the base. Carefully lower the base.
Elastic loop should be touching leg of base
N (not
OTE
:
wrapped
on top of strap).
STEP 6
Repeat steps 3-5 to install second strap at the
other end of the bed.
13
IF YOU EXPERIENCE ANY TROUBLE
WITH YOUR ADJUSTABLE BASE WITHIN
THE WARRANTY PERIOD, PLEASE
CONSULT THE TROUBLESHOOTING
GUIDE PROVIDED WITH YOUR
FRAME AND ONLINE (IF APPLICABLE).
IF PROBLEMS PERSIST, PLEASE CALL.
CUSTOMER SERVICE
TOLL FREE NUMBER:
1300 130 221
Please have your receipt ready
and available.
THANK YOU AND ENJOY YOUR
ADJUSTABLE BASE!
14
13
Warranty
ADJUSTABLE BASE:
10 YEAR LIMITED WARRANTY
SEALY GUARANTEES THAT WE WILL, AT
SEALY’S OPTION, REPLACE OR REPAIR
PURCHASER’S SEALY® SYSTEM IF IT IS
DEFECTIVE DUE TO FAULTY
WORKMANSHIP OR MATERIALS,
SUBJECT TO THE LIMITATIONS
DESCRIBED IN THIS WARRANTY.
Notwithstanding anything else contained in this
warranty, our goods come with guarantees that cannot
be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major
failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not
amount to a major failure.
YEAR 1: FULL COVERAGE OF PARTS
AND LABOR
Your Sealy adjustable base system is warranted against
defects in the workmanship or materials for a period of
one (1) year from the warranty commencement date.
Electronics, electrical components, drive motors and
massage motors are included. Upon notice during the
first year from the warranty commencement date,
Sealy will send replacement parts (at no cost to the
purchaser) for any defective part to the purchaser, and
Sealy will pay all authorized labour and transportation
costs associated with the repair or replacement of any
parts Sealy determines to be defective. This one (1) year
warranty shall not apply if purchaser does not return
any and all defective parts to Sealy within 15 days of
purchaser’s receipt of replacement part.
YEARS 2 AND 3: FULL COVERAGE OF
PARTS ONLY
Upon notice during the years two and three (2–3) from
the warranty commencement date, Sealy will offer
replacement parts for any defective part to the
purchaser. Electronics, electrical components, drive
motors and massage motors are included. This two (2)
year warranty shall not apply if purchaser does not
return any and all defective parts to Sealy within 15
14
days of purchaser’s receipt of replacement part.
Purchaser shall bear all service, transportation, labour,
and shipping costs related to the delivery and/or
replacement of the defective part.
YEARS 4 THROUGH 10: PRORATED
COVERAGE OF PARTS ONLY
Upon notice during the fourth through the tenth (4–10)
years from the warranty commencement date, Sealy
will offer replacement parts (upon terms and
conditions set forth in this paragraph) for any
mechanical bed part found to be defective. Electronics,
electrical components, drive motors and massage
motors are excluded. Purchaser shall pay 1/7th of the
then current replacement cost of the defective part
multiplied by the number of years after three (3) years
from the warranty commencement date, and Sealy
shall bear the remainder of the cost of the replacement
part. This seven (7) year warranty shall not apply if
purchaser does not return any and all defective parts to
Sealy within 15 days of purchaser’s receipt of
replacement part. Purchaser shall bear all service,
transportation, labour, and shipping costs related to the
delivery and/ or replacement of the defective part. After
the 10th year, purchaser shall bear the entire cost of
repair and replacement of all parts and materials,
including labour and transportation.
ADDITIONAL TERMS AND CONDITIONS
This warranty does not apply;
a) to any damage caused by the purchaser;
b) if there has been any unauthorized repair or
replacement of the unit’s parts;
c) if the unit has been mishandled (whether in transit or
by other means), subjected to physical or electrical
abuse or misuse, or otherwise operated in any way
inconsistent with the operation and maintenance
procedures outlined in the Complete Reference Guide,
this warranty, and any other applicable document
published or approved by Sealy;
d) to damage to mattresses, fabric, cables, electrical
cords or items supplied by Resellers;
e) if there has been any unnecessary service calls,
including costs for in home service calls solely for the
purpose of educating the consumer about the unit for
finding an unsatisfactory power connection; and
f) if the recommended weight restrictions are not
followed (Twin Long, Split/Dual CA King:260kg;
Queen: 295kg), the warranty will be void.
Repairs to or replacement of the Sealy® system or its
components under the terms of this limited warranty
will apply to the original warranty period and will not
serve to extend such period. The decision to repair or
to replace defective parts under this warranty shall be
made, or case to be made, by Sealy at its option and in
its sole discretion.
SUBJECT TO THE AUSTRALIAN CONSUMER LAW,
REPAIR OR REPLACEMENT SHALL BE THE SOLE
REMEDY OF THE PURCHASER. THERE SHALL BE NO
LIABILITY ON THE PART OF SEALY FOR ANY SPECIAL,
INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES OR FOR ANY OTHER DAMAGE, CLAIM, OR
LOSS NOT EXPRESSLY COVERED BY THE TERMS OF
THIS WARRANTY. THIS LIMITED WARRANTY DOES
NOT INCLUDE REIMBURSEMENT FOR
INCONVENIENCE, REMOVAL, INSTALLATION,
SETUP TIME, LOSS OF USE, SHIPPING, OR ANY OTHER
COSTS OR EXPENSES. SEALY MAKES NO OTHER
WARRANTY WHATSOEVER, EXPRESS OR IMPLIED, AND
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED
BY SEALY AND EXCLUDED FROM THIS AGREEMENT.
This warranty gives the purchaser specific legal rights.
This warranty is valid only for the original purchaser of
the product. An original purchaser is one who
purchases the product directly from Sealy Australia or
an authorized Reseller of Sealy. If you are not the
original purchaser of this Product, you take it “as is” and
“with all faults“If you did not purchase this Sealy
system directly from Sealy, we will require proof of
purchase from you demonstrating that you are the
original purchaser and eligible to make a valid claim
under this warranty. This warranty begins on the
“warranty commencement date” which is the date of
purchase for new unused units, and the date of
manufacture for units that have been used as floor or
display models. Thus, on a floor model unit, the
warranty is a portion of the limited 10 year warranty. If
original proof of purchase is not provided by purchaser,
Sealy reserves the right to determine if the unit is not
covered by this warranty or to use the manufacturing
date as the warranty commencement date. This limited
warranty gives you specific legal rights.
If you experience any trouble with your Sealy® system
during the warranty period, please consult the
troubleshooting section of your Reference Guide. If
problems persist after following these instructions,
please call: 1300 130 221.
15
16
IF YOU EXPERIENCE ANY TROUBLE WITH YOUR ADJUSTABLE BASE
WITHIN THE WARRANTY PERIOD, PLEASE CONSULT THE TROUBLESHOOTING
GUIDE PROVIDED WITH YOUR FRAME AND ONLINE (IF APPLICABLE).
IF PROBLEMS PERSIST, PLEASE CALL.
CUSTOMER SERVICE TOLL FREE NUMBER:
1300 130 221
Please have your receipt ready and available.
THANK YOU AND ENJOY YOUR ADJUSTABLE BASE!
Model Number:
SEALY-AU-SPEC-7937
Reference Codes:
Queen: SA-ABF-A18-N6S220-W-SRB-9V2-110-(20301525M)
Single XL: SA-ABF-A18-N6S220-W-SRB-9V2-110-(2030915M)
Serial Number
©2016 Sealy of Australia
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising