electric fireplace mantel - Electric Fireplaces Direct

electric fireplace mantel - Electric Fireplaces Direct
PDFMAILER.COM
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
ELECTRIC FIREPLACE MANTEL
26MM9404
INSTRUCTION MANUAL
Español p. 9
Français p. 17
FIT UP TO 62”PLASMA/LCD TELEVISIONS
MAXIMUM LOAD 135 lb. (61.22 kg)
MAXIMUM LOAD 30 lb. (13.6kg)
CAUTION: This unit is intended for use only with the products and maximum weights
indicated. Use with other products or products heavier than the maximum weights
indicated may result in instability causing possible injury.
Note: Flat Panel TVs with base support should be placed squarely in the center of the
stand with no overhang on any side.
For Customer Service:
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in China
Printed in China
E-mail: parts@twinstarhome.com
In English call: 866-661-1218
In French call: 866-374-9203
In Spanish call: 866-661-1218
1
AT T E N T I O N
Requires-Electric Fireplace
Insert with Heater
PDFMAILER.COM
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
PACKAGE CONTENTS
G
N
F
O
M
H
K
L
C
O
B
D
P
H
L
E
H
H
J
I
A
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Description
Hearth/Base
Center Left Side Panel
Center Right Side Panel
Center Front Panel
Left Side Panel
Right Side Panel
Glass Top
Glass Shelf
Left Front Panel
Right Front Panel
Center Shelf
Glass Door
Left Top Panel
Right Top Panel
Side Back Panel
Insert Support Bar
2
Quantity
1
1
1
1
1
1
1
4
1
1
1
2
1
1
2
1
PDFMAILER.COM
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
HARDWARE CONTENTS
Part
Description
Picture
(Shown to size)
Quantity
AA
Bolt
29+1 extra
BB
Washer
29+1 extra
CC
Wood Dowel
24+1 extra
DD
Door Touch Clip
2
EE
Suction Cup
8
FF
Pivot Hinge
4
GG
Magnetic Spring Catch
2
HH
Shelf Pin
II
Metal Support Post
16
8
JJ
Screw
34
KK
Screw
8
LL
Tipping Restraint
Hardware
2
ZZ
Touch-up Pen
1
3
PDFMAILER.COM
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
SAFETY INFORMATION
WARNING
•Before assembly, carefully use scissors or utility knife to cut and unwrap all parts.
Make sure you do not discard the hardware.
CAUTION
•Use care in assembling your new replace. Take your time and use the hardware
provided and a quality Phillips head screwdriver. Never overtighten bolts.
•Do not sit on any part of the mantel.
•All panels are labeled left and right as viewed from the front of unit.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.
Estimated Assembly Time: 60 Minutes
Tools Required for Assembly (not included): Phillips head screwdriver, scissors and utility knife
ASSEMBLY INSTRUCTIONS
1. Locate the Center Shelf (K) and Center Front Panel
(D) on a scratchproof surface. Attach the Center
Shelf (K) and Center Front Panel (D) using Bolts
(AA) and Washers (BB) through the pri-drilled holes
and tighten .
Fig. 1
D
K
Hardware Used
AA
Bolt
x3
BB
Washer
x3
BB
AA
4
PDFMAILER.COM
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
2. Locate the Left Front Panel (I), Right Front Panel
(J), the completed assembly from step 1. Insert one
Wood Dowel (CC) into each of the pre-drilled holes.
Push the Left Front Panel (I) and Right Front Panel
(J) snug to the completed assembly from step 1.
Make sure the Wood Dowels (CC) are seated in the
pre-drilled holes. Connect the Left Front Panel (I),
Right Front Panel (J) and completed assembly with
Connection Plate, tighten Screws through the
pre-drilled holes.
Fig. 2
CC
JJ
Hardware Used
I
J
CC
Wood Dowel
x4
JJ
Screw
x2
3. Insert one Wood Dowel (CC) into each of the
pre-drilled holes in the completed assembly form
step 2 .Attach the Completed assembly to the
Center Left Side Panel (B) and Center Right Side
Panel (C). Make sure that dowels are seated into the
pre-drilled holes. Using Bolts (AA) and Washers
(BB) attach panels through pre-drilled holes in the
mounting blocks.
HAND TIGHTEN ONLY.
Hardware Used
Fig. 3
CC
CC
B
C
AA
Bolt
x8
BB
Washer
x8
CC
Wood Dowel
x4
BB
AA
4. Locate Hearth/Base (A) and set out nished side up
on the oor.
Insert one Wood Dowel (CC) into each of the
pre-drilled holes.
Attach the Completed assembly from step 3 to the
Hearth/Base (A). Make sure that dowels are seated
into the pre-drilled holes in the Hearth/Base. Using
Bolts (AA) and Washers (BB) attach panels through
pre-drilled holes in the mounting blocks.
HAND TIGHTEN ONLY.
Insert one Wood Dowel (CC) into each of pre-drilled
holes. Push the Right Side Panel (F) and Left Side
Panel (E) snug to completed assembly. Using Bolts
(AA) and Washers (BB) through the pre-drilled holes
in the mounting blocks.
HAND TIGHTEN ONLY.
Hardware Used
AA
Bolt
x8
BB
Washer
x8
CC
Wood Dowel
x8
5
Fig. 4
E
AA
AA
F
BB
BB
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
PDFMAILER.COM
www.pdfmailer.com
5. Insert Left Top Panel (M) and Right Top Panel (N),
from the inside, attach the Top panel using Bolts
(AA) and Washers (BB) through the pre-drilled
holes in the mounting blocks.
HAND TIGHTEN ONLY.
Fig. 5
M
N
Hardware Used
AA
Bolt
DD
x8
BB
CC
BB
Washer
x8
BB
CC
Wood Dowel
x8
AA
6. Attach Side Back Panels (O) to the back of the
completed assembly from step 5. Use a Phillips
Head Screw Driver, tighten Wood Screws (JJ)
through the pre-drilled holes in the Side Back Panels
(O).
AA
Fig. 6
JJ
Hardware Used
JJ
Screw
x 32
O
7. Attach the Magnetic Spring Catch (GG) on the
bottom of Top Panel, tighten screws (KK) through
holes to the block as shown in diagram.
Place the Door Touch Clip (DD) to the glass door.
Insert the Pivot Hinge (FF) into the plastic mat as
shown in diagram. Then push the Glass Doors (L)
snug to the Pivot Hinges (FF), use a Phillips Head
Screwdriver to tighten the pivot hinge against the
glass.
O
Fig. 7
DD
GG
WARNING
Do not over tighten catch screws.
Damage to the Glass could occur!
KK
Hardware Used
L
DD
Door Touch Clip
x2
FF
Pivot Hinge
x4
GG
Magnetic Spring
Catch
x2
KK
screw
x8
L
FF
6
PDFMAILER.COM
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
8. Choose desired height of Glass Shelf (H) and place
the four Shelf Pin (HH) into same height shelf holes
inside side panels. Insert Glass Shelf (H), allow
Glass Shelf (H) to rest on the Shelf Pin (HH).
Fig. 8
Hardware Used
HH
Shelf Pin
x 16
H
HH
9. Attach the Metal Support Post (II) and screw
clockwise into inset threads on the top of the mantel.
Insert the Suction Cups (EE) into the Support Posts,
with the help of another adult carefully lower the
Glass Top (G) onto the Support Posts.
Fig. 9
EE
II
G
Hardware Used
EE
II
Suction Cup
x8
M e ta l S u p p o r t
Post
x8
10. PLEASE READ ALL “ELECTRIC FIREPLACE
INSERT”INSTRUCTIONS PRIOR TO
INSTALLING ELECTRIC INSERT IN YOUR
COMPLETED FIREPLACE MANTEL. INSTALL
THE INSERT IN YOUR FIREPLACE CLOSE TO
ITS FINAL POSITION.
Lift insert carefully into the back of the unit and
center in the insert opening. Do not drag insert
across hearth/base as it may scratch the unit.
Connect the Insert Support Bar (P) to the inside left
and right panels, using the bolt (AA) and washer
(BB) through pre-drilled holes.
MOVE YOUR COMPLETED UNIT ONLY SHORT
DISTANCES. MOVE COMPLETED UNIT WITH
GREAT CARE. IT TAKES TWO PEOPLE TO
MOVE COMPLETED UNIT INTO ITS FINAL
POSITION.
Fig. 10
Install
Insert
From
Back
Electric
Fireplace Insert
Completed
Unit
Hardware Used
P
AA
Bolt
x2
BB
Washer
x2
AA BB
7
PDFMAILER.COM
www.pdfmailer.com
Print and send PDF files as Emails with any application, ad-sponsored and
free of charge www.pdfmailer.com
11. We have included two Tipping Restraints for this
unit. You must install this hardware to prevent
accidents or injuries. When properly installed, this
restraint can provide protection against unexpected
tipping of the Unit due to small tremors, bumps or
climbing. We strongly recommend mounting this
hardware to a wall stud and your Unit.
Fig. 11
Wall Stud
Cabinet
Wall
LL
Warning: You must install the Tipping Restraint
Hardware to help prevent accidents or damage to
the unit.
Hardware Used
LL
Tipping Restraint
Hardware
x2
8
03/08/11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising