60V Cordless String Trimmer 2103102CT

60V Cordless String Trimmer 2103102CT
60V Cordless String Trimmer
2103102CT
Owner’s Manual
TOLL-FREE HELPLINE: 1-855-345-3934
www.GreenWorksTools.com
Read all safety rules and instructions carefully before operating this tool.
CONTENTS
Contents............................................................................................................................... 2
Product Specifications ......................................................................................................... 2
Important Safety Instructions................................................................................................ 3
Symbols................................................................................................................................ 5
Know Your String Trimmer.................................................................................................... 7
Assembly.............................................................................................................................. 9
Operation............................................................................................................................ 1 5
Battery & Charger Maintenance........................................................................................... 2 3
Maintenance........................................................................................................................... 25
Environmentally Safe Battery Disposal .................................................................................26
Troubleshooting..................................................................................................................27
Limited Warranty................................................................................................................29
Exploded View and Part List................................... ..............................................................30
PRODUCT SPECIFICATIONS
60V CORDLESS STRING TRIMMER
Type.............................................................................................. Cordless, battery powered
Motor................................................................................................................................6 0V
Cutting Width ......................................................................................................14 in (35.6 cm)
Line Diameter ..................................................................................Nylon / 0.080" (2 mm)
Speed .................................................................................................6000 / 7000 (±10%) RPM
Feed Type ...............................................................................................................Bump Feed
Weight (without battery) ...............................................................................7.1 lbs (3.2 kg)
Charge time..............................................................................................................60 minutes
2
IMPORTANT SAFETY INSTRUCTIONS
WA R N I N G
Read and understand all instructions before using this product. Failure to follow all
instructions listed below may result in electric shock, fire, and/or serious personal injury.
•Use only identical manufacturer’s replacement parts and accessories. Use of any other parts
may create a hazard or cause product damage.
•Always wear safety glasses with side shields marked to comply with ANSI Z87.1. Everyday
glasses have only impact resistant lenses. They are NOT safety glasses. Following this rule
will reduce the risk of eye injury. Use a face mask if operating in dusty work spaces.
•Avoid Dangerous Environment — Don’t expose power tools to damp or wet conditions. Water
entering a power tool will increase the risk of electric shock.
•Do not use in rain.
•Keep all bystanders, children, and pets at least 50 ft. away.
•Do not use the power tools for any job except that for which it is intended.
•Avoid Unintentional Starting – Do not carry the string trimmer with fingers on the switch. Be
sure the battery is removed while transporting.
•Do not operate the equipment while barefoot or when wearing sandals or similar lightweight
footwear. Wear protective footwear that will protect your feet and improve your footing on
slippery surfaces.
•Don’t overreach - Keep proper footing and balance at all times.
•Stay alert - Watch what you are doing. Use common sense. Do not operate this unit when you
are tired, ill or under the influence of alcohol, drugs or medication.
•Always store idle power tools indoors - When not in use, power tools should be stored indoors
in a dry place, out of reach of children.
•Power tool maintenance – Replace string head if cracked, chipped, or damaged in any
way. Be sure the string head is properly installed and securely fastened. Keep cutting edge
sharp and clean for best performance and to reduce the risk of injury. Follow instructions for
lubricating and changing accessories. Inspect appliance cord periodically, and if damaged,
have it repaired by an authorized service facility. Inspect extension cords periodically and
replace if damaged. Keep handles dry, clean, and free from oil and grease. Failure to do so
can cause serious injury.
•Check Damaged Parts – Before further use of the appliance, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment of moving parts, binding of moving parts, breakage of
parts, damaged mountings, and any other condition that may affect its operation. A guard or
other part that is damaged should be properly repaired or replaced by an authorized service
center unless indicated elsewhere in this manual.
•Do not charge or operate cordless tools in damp or wet locations or in the rain. Following this
rule will reduce the risk of electric shock.
•Remove or disconnect battery before servicing, cleaning or removing material from the
gardening appliance.
3
IMPORTANT SAFETY INSTRUCTIONS
•Do not dispose of the batteries in a fire. The cells may explode. Check with local codes for
possible special disposal instructions.
•Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if swallowed.
•Exercise care in handling batteries in order not to short the battery with conducting materials
such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.
•Dress Properly – Do not wear loose clothing or jewelry. They can be caught in moving parts.
Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear
protective hair covering to contain long hair.
•Do not add unnecessary force to your power tool – It will do the job better and with less
likelihood of a risk of injury at the rate for which it was designed.
•Recharge only with the charger specified by the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire when used with another battery pack.
•For use only with 2906402CT battery. For use only with 2910402CT charger.
•When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal
to another. Shorting the battery terminals together may cause a fire.
•Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
•Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries
may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
•Do not expose a battery pack or power tools to fire or excessive temperature. Exposure to fire
or temperature above 265°F (130°C) may cause explosion.
W A R N I N G (PROPOSITION 65)
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
•Lead from lead-based paints
•Crystalline silica from bricks and cement and other masonry products, and
•Arsenic and chromium from chemically treated lumber.
Your risk of exposure to these chemicals varies depending on how often you do this type of
work. To reduce your exposure to these chemicals, work in a well-ventilated area, and work with
approved safety equipment, such as dust masks that are specially designed to filter out microscopic
particles.
SAVE THESE INSTRUCTIONS
4
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
W
Watts
Power
Minutes
Time
min
/min
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
No Blade
Do not install or use any type of blade on a
product displaying this symbol.
Per Minute
Revolutions, strokes, surface speed, orbits
etc., per minute.
Wet Conditions Alert
Do not expose to rain or use in damp locations.
Read The Operator’s Manual
To reduce the risk of injury user must read and
understand operator’s manual before using
this product.
Eye Protection
Always wear eye protection with side shields
marked to comply with ANSI Z87.1 when
operating this equipment.
Safety Alert
Precautions that involve your safety.
Ricochet
Thrown objects can ricochet and result in
personal injury or property damage.
Keep Bystanders Away
Keep all bystanders at least 50 ft. away.
5
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated
with this product.
SYMBOL
SIGNAL
MEANING
DANGER
Indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided,
may result in minor or moderate injury.
CAUTION
(Without Safety Alert Symbol) Indicates a situation that may
result in property damage.
SERVICE
Servicing requires extreme care and knowledge and should be performed only by a qualified
service technician. For service we suggest you return the product to your nearest AUTHORIZED
SERVICE CENTER for repair. Use only identical manufacturer’s replacement parts and
accessories.
WA R N I N G
To avoid serious personal injury, do not attempt to use this product until you have read this Owner's
Manual thoroughly and understand it completely. If you do not understand the warnings and
instructions in this Owner's Manual, do not use this product. Call the Toll-free Helpline (1-855-3453934) for assistance. The operation of any power tool can result in foreign objects being thrown
into your eyes, which can result in severe eye damage. Before operating a power tool, always wear
safety goggles, safety glasses with side shields, or a full face shield when needed. We recommend
a Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
Always use eye protection that is marked to comply with ANSI Z87.1.
WA R N I N G
The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always
wear safety goggles or safety glasses with side shields and, when needed, a full face
shield. We recommend Wide Vision Safety Mask for use over eyeglasses or standard
safety glasses with side shields. Always use eye protection which is marked to comply
with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
6
KNOW YOUR STRING TRIMMER
1
2
9
8
7
3
4
6
11
5
10
Fig. 1
7
KNOW YOUR STRING TRIMMER
KNOW YOUR STRING TRIMMER (See Figure 1.)
The safe use of this product requires an understanding of the information on the product and in
this operator’s manual as well as a knowledge of the project you are attempting. Before use of this
product, familiarize yourself with all operating features and safety rules.
1. BATTERY PACK LATCH
Press to release the battery pack from the tool.
2. REAR HANDLE
Ergonomic handle with overmold improves comfort and grip.
3. AUXILIARY HANDLE
The string trimmer is equipped with an auxiliary handle for ease of operation and to prevent loss
of control.
4. COUPLER
The coupler connects and locks the two shafts.
5. GUARD
The trimmer includes a guard that helps protect from flying debris.
6. TRIMMER SHAFT
The trimmer shaft encloses and protects the cables between the motor and rear handle.
7. HIGH/LOW SPEED BUTTON
The high/low speed button adjusts the speed.
8. VARIABLE SPEED TRIGGER
Provides added control and precision.
9. SAFETY LOCK BUTTON
The safety lock button prevents accidental starting.
10. CUT-OFF BLADE
Adjustable steel blade on the guard keeps the cutting line at the proper cutting length.
11. REMOVEABLE EDGE GUIDE
Prevents string trimmer from damaging property while in use.
8
ASSEMBLY
UNPACKING
This product requires assembly.
•Carefully remove the product and any accessories from the box. Make sure that all items
listed in the packing list are included.
•Inspect the tool carefully to make sure no breakage or damage occurred during shipping.
•Do not discard the packing material until you have carefully inspected and satisfactorily
operated the tool.
•If any parts are damaged or missing, please call 1-855-345-3934.
WA R N I N G
Do not use this product if any parts on the packing list are already assembled to your product when
you unpack it. Parts on this list are not assembled to the product by the manufacturer and require
customer installation. Use of a product that may have been improperly assembled could result in
serious personal injury.
PACKING LIST
Part Name
Figure
Qty
String trimmer
1
Auxiliary handle
1
Guard
1
Edge guide
1
V
60
m
Tri
g
in
Str 00
ss L
le 60
rd ST
Co
er
m
Operator's manual
ty
fe
l sa
al
s
le
ru
to
34
is
39
th
g
5l
in
at
ua 5-34 m
er
op
an 85 co
re
M 1- s.
fo
s E: ol
be
er’ LIN ksTo
lly
fu
or
wn
re
O HELP W
ca
en
ns
io
E re
ct
ru
RE .G
st
-F ww
in
w
d
ad
Re
LL
TO
an
.
ol
9
1
ASSEMBLY
WA R N I N G
If any parts are damaged or missing, do not operate this product until the parts are replaced. Use
of this product with damaged or missing parts could result in serious personal injury.
WA R N I N G
Do not attempt to modify this product or create accessories not recommended for use with this
string trimmer. Any such alteration or modification is misuse and could result in a hazardous
condition leading to possible serious personal injury.
WA R N I N G
Do not connect to power supply until assembly is complete. Failure to comply could result in
accidental starting and possible serious personal injury.
ATTACHING THE EDGE GUIDE
The edge guide can limit the cutting range of the trimmer and reduce the risk of the rotating
cutting line causing damage.
To use the edge guide, press the edge guide onto the trimmer head.
Fig. 2.1
Fig. 2.2
10
ASSEMBLY
ATTACHING THE GUARD (See Figure 3.)
NOTE: Install the guard before the attachment is connected to the lower shaft.
1.
2.
Invert the string trimmer to access the trimmer head.
Remove supplied screws (1) from the trimmer head (4) with a philips head screwdriver (not
included).
1
Fig. 3.1
4
3.
4.
Place the guard (2) on to the trimmer head.
Align the screw holes on the guard (3) with the screw holes on the trimmer head (4)
2
3
4
Fig. 3.2
5.
Insert the screws into the trimmer head, fastening the guard in place using a philips head
screwdriver (not included).
Fig. 3.3
ASSEMBLY
INSTALLING THE UPPER SHAFT TO THE LOWER SHAFT (See Figure 4.)
WA R N I N G
Never install, remove, or adjust any attachment while the string trimmer is running. Failure to stop
the motor can cause serious personal injury.
The attachment connects to the power head by means of a coupler device.
1.
Set the unit on a flat, level surface.
2.
Loosen the knob (1) on the coupler (5).
3.
Push in the release button (2) located on the lower shaft (3). Align the release button with
the positioning hole (4) and slide the two shafts together. Rotate the lower shaft until the
button locks into the positioning hole.
4
3
2
2
5
Fig. 4.1
1
NOTE: If the button does not release completely in the positioning hole, the shafts are not locked
into place. Slightly rotate from side to side until the button is locked into place.
4.
Tighten the knob securely.
5
LOOSE
TIGHTEN
1
12
Fig. 4.2
ASSEMBLY
ATTACHING THE AUXILIARY HANDLE (See Figure 5.)
1.
Loosen the two screws (1) in the handle with a philips screwdriver (not included) and
remove the screws from the handle.
1
Fig. 5.1
2.
3.
Attach the auxiliary handle (2) and lower clamp (3) on the shaft.
Adjust handle up or down, if necessary, to desired operating position.
2
3
4.
Fig. 5.2
Insert and tighten the two screws so that the handle cannot be rotated on the shaft.
13
ASSEMBLY
ADJUSTING THE CUTTING SWATH (See Figure 6.)
This trimmer is equipped with a line cut-off blade on the guard. The line cut off blade
continuously trims the line to ensure a consistent and efficient cut diameter. Advance line
whenever you hear the engine running faster than normal, or when trimming efficiency
diminishes. This will maintain best performance and keep line long enough to advance properly.
Screw
Cut-off blade
Fig. 6
14
OPERATION
WA R N I N G
Do not allow familiarity with this product to make you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WA R N I N G
Do not use any attachments or accessories not recommended by the manufacturer of this product.
The use of attachments or accessories not recommended can result in serious personal injury.
WA R N I N G
This string trimmer is not meant to be used with a brush cutter attachments. Use of a brush cutter
attachment could cause serious personal injuries or property damage.
15
OPERATION
INSTALLING THE BATTERY PACK (See Figure 7.)
•Align the battery with the battery opening.
•Insert battery pack into tool until an audible "click" is heard.
REMOVING THE BATTERY PACK (See Figure 7.)
•Press the battery release button (1) in the back of the trimmer and pull battery pack out of tool.
1
Fig. 7
STARTING AND STOPPING THE TRIMMER (See Figure 8.)
•Slide the speed switch (1) to the desired operating speed. Slide the speed switch to position 1
for low speed or position 2 for high speed.
•Press the lock-off lever (2). Squeeze the switch trigger (3) to start.
•Release the switch trigger to stop.
2
1
3
Fig. 8
16
OPERATION
OPERATING THE TRIMMER (See Figure 9.)
WA R N I N G
Always hold the string trimmer away from the body keeping clearance between the body and the
string trimmer. Any contact with the string trimmer cutting head while operating can result in serious
personal injury.
Follow these tips when using the string trimmer:
•Hold the trimmer with your right hand on the rear handle and your left hand on the auxiliary
handle.
•Keep a firm grip with both hands while in operation.
•Trimmer should be held at a comfortable position with the rear handle about hip height.
•Cut tall grass from the top down. This will prevent grass from wrapping around the shaft
housing and string head which may cause damage from overhearing.
If grass becomes wrapped around the string head:
• Remove the battery pack.
• Remove the grass.
Fig. 9
17
OPERATION
ADVANCING LINE (See Figure 10.)
While the string trimmer is operating, the cutting line gets worn down and becomes shorter.
This trimmer is equipped with bump feed line advancement, which advances additional line
once the head is bumped on the ground while rotating. The cutting blade will cut the line to
keep an accurate cutting swath.
Bump knob
Fig. 10
REPLACING THE LINE (See Figure 11.)
1.
Press the tabs simultaneously on the side of the trimmer head and remove cover and spool.
Cover
Spool
Tab
Fig. 11.1
2.
3.
4.
Remove any remaining line.
Clean dirt and debris from all parts. Replace spool if it is worn or damaged.
Replace with a pre-wound spool, or replace line using 10 feet (3 meters) of 0.080 inch (2.0
mm) diameter line.
WA R N I N G
Never use wire, rope, string, etc., which can break off and become a dangerous projectile.
18
OPERATION
5.
6.
When installing new line on an existing spool, hold the spool as shown.
Bend the line at the midpoint and insert the bend into the slot in the center rim of the spool.
Ensure line snaps into position in the slot.
Slot
Fig. 11.2
7.
With your finger between the lines, wrap the lines evenly and firmly around the spool in a
clockwise direction.
Fig. 11.3
8.
Position the lines in the guide slots.
Fig. 11.4
19
OPERATION
9.
Place the spool in the cover as shown below.
Fig. 11.5
10. Insert the ends of the lines through the line exit holes in the sides of the cover.
Fig. 11.6
11. Reinstall the spool and cover onto the trimmer head. Push until cover snaps into place.
Fig. 11.7
20
OPERATION
REPLACING THE BUMP KNOB (See Figure 12.)
1.
2.
Remove the battery pack.
Press the tabs simultaneously on the side of the trimmer head and remove cover and spool.
Cover
Spool
Tab
Fig. 12.1
3.
While holding the bump knob (1), firmly pull it out.
1
Fig. 12.2
4.
Replace with a new bump knob (1). Push the bump knob into the spool housing (2).
1
2
Fig. 12.3
21
OPERATION
CUTTING TIPS (See Figure 13.)
•Keep the trimmer tilted toward the area being cut; this is the best cutting area.
•The trimmer cuts when passing the unit from right to left. This will avoid throwing debris at the
operator. Avoid cutting in the dangerous area shown in figure 13.
•Use the tip of string to do the cutting; do not force string head into uncut grass.
•Wire and picket fences cause extra string wear and breakage. Stone and brick walls, curbs,
and wood may wear string rapidly.
•Avoid trees and shrubs. Tree bark, wood moldings, siding, and fence posts can easily be
damaged by the string.
DIRECTION OF ROTATION
DANGEROUS CUTTING AREA
BEST CUTTING AREA
22
Fig. 13
MAINTENANCE
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from
various types of commercial solvents and may be damaged by their use. Use clean cloths to
remove dirt, dust, lubricant, grease, etc.
Always store the machine clean and in a dry enclosure with the battery charged.
Maintenance task
Visual check of the tool's
safety systems (distancing
device, carrying eye, safety
casing)
Each time
Every two
the machine
hours
is used
X
Each week After use
Every year
or when
required
X
Check the trigger safety
system functions
X
Check the sharpness of
blades and sharpen if
necessary
X
X
X
Visual check of the tool (no
cracks or deformation)
X
X
X
Check the battery level
X
23
ENVIRONMENTALLY SAFE BATTERY DISPOSAL
The following toxic and corrosive materials are in the batteries used in this string trimmer battery
pack: Lithium-Ion, a toxic material.
WA R N I N G
All toxic materials must be disposed of in a specified manner to prevent contamination of the
environment. Before disposing of damaged or worn out Lithium-Ion battery packs, contact your
local waste disposal agency, or the local Environmental Protection Agency for information and
specific instructions. Take the batteries to a local recycling and/or disposal centre, certified for
lithium-ion disposal.
WA R N I N G
If the battery pack cracks or breaks, with or without leaks, do not recharge it and do not use.
Dispose of it and replace with a new battery pack. DO NOT ATTEMPT TO REPAIR IT!​
To avoid injury and risk of fire, explosion, or electric shock, and to avoid damage to the
environment:
•
Cover the battery's terminals with heavy-duty adhesive tape.
•
DO NOT attempt to remove or destroy any of the battery pack components.
•
DO NOT attempt to open the battery pack.
•
If a leak develops, the released electrolytes are corrosive and toxic. DO NOT get the
solution in the eyes or on skin, and do not swallow it.
•
DO NOT place these batteries in your regular household trash.
•
DO NOT incinerate.
•
DO NOT place them where they will become part of any waste landfill or municipal solid
waste stream.
•
Take them to a certified recycling or disposal centre.
24
TROUBLESHOOTING
Problem
String trimmer
fails to start
when trigger is
pressed.
Cause
Solution
1. The battery pack is not
connected to the trimmer.
1. Attach the battery pack to the trimmer.
2. No electrical contact
between the trimmer and
battery.
2. Remove battery check contact and reinstall
the battery pack.
3. The battery pack is depleted. 3. Charge the battery pack.
4. The lock-off lever and
trigger are not pressed
simultaneously.
4. Press down the lock-off lever and hold it,
then press the trigger to turn on the string
trimmer.
1. The guard is not mounted
on the trimmer, resulting in an 1. Remove the battery pack and mount the
overly long cutting and motor guard on the trimmer.
overload.
String trimmer
stops while
cutting.
2. Heavy cutting line is used.
2. Use only with nylon cutting line 0.080"
diameter or less.
3. The motor shaft or trimmer
head is bound with grass.
3. Stop the trimmer, remove the battery, and
remove the grass from the motor shaft and
trimmer head.
4. The motor is overloaded.
4. Remove the trimmer head from the grass.
The motor will recover to work as soon as
the load is removed. When cutting, move the
trimmer head in and out of the grass to be cut
and remove no more than 8 inches of length
in a single cut.
5. The battery pack or string
trimmer is too hot.
5. Allow the battery pack to cool until the
temperature drops below 158°F (70°C).
Allow the trimmer to cool until the temperature
drops below 284°F (140°C).
6. The battery pack is
disconnected from the tool.
6. Re-install the battery pack.
7. The battery pack is depleted. 7. Charge the battery pack.
25
TROUBLESHOOTING
Problem
Lines will not
advance.
Line keeps
breaking.
Cause
Solution
1. Lines are welded to
themselves.
1. Lubricate with silicone spray.
2. Not enough line on
spool.
2. Install more line. Refer to Line
Replacement earlier in this manual.
3. Lines are worn too short.
3. Pull both lines while pressing button.
4. Lines are tangled on
spool.
4. Remove lines from spool and rewind.
Refer to Line Replacement earlier in
this manual.
1. Trimmer used incorrectly.
1. Only trim with the tip of the line, avoid
stones, walls and other hard objects. Feed the
line regularly to maintain full cutting width.
Grass wraps
1. Cut tall grass from the top down, removing
around trimmer 1. Cutting tall grass at ground
no more than 8 inches in each pass to prevent
head and motor level
wrapping.
housing.
Line is not
cutting well
1. The line-cutting blade on the
1. Sharpen the line-cutting blade with a file or
edge of the guard has become
replace it with a new blade.
dull.
26
LIMITED WARRANTY
GREENWORKS™ hereby warranties this product, to the original purchaser with proof
of purchase, 4 year warranty against defects in materials, parts or workmanship.
GREENWORKS™, at its own discretion will repair or replace any and all parts found to be
defective, through normal use, free of charge to the customer. This warranty is valid only for
units which have been used for personal use that have not been hired or rented for industrial/
commercial use, and that have been maintained in accordance with the instructions in the
owners’ manual supplied with the product from new.
ITEMS NOT COVERED BY WARRANTY:
1.Any part that has become inoperative due to misuse, abuse, neglect, accident, improper
maintenance, or alteration; or
2.The unit, if it has not been operated and/or maintained in accordance with the owner's
manual; or
3.Normal wear, except as noted below;
4.Routine maintenance items such as lubricants, blade sharpening;
5.Normal deterioration of the exterior finish due to use or exposure.
GREENWORKS HELPLINE (1-855-345-3934):
Warranty service is available by calling our toll-free helpline at (1-855-345-3934).
TRANSPORTATION CHARGES:
Transportation charges for the movement of any power equipment unit or attachment are the
responsibility of the purchaser. It is the purchaser’s responsibility to pay transportation charges
for any part submitted for replacement under this warranty unless such return is requested in
writing by GREENWORKS.
27
EXPLODED VIEW
28
PARTS LIST
Item No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Part No.
310011453
32201836
341081468
34105836-4
34203836
33301836
34201877
341111437AB
333031453
332041428
341041429AB
311101429
311091429
341131453
322011429
333011429
32207319
32916131
211011382CT
211011989CT
Description
Bare tool assembly
Screw and washer assembly
Cover
Auxiliary handle
Rubber washer
Clamp
Rubber ring
Knob
Edge guide
Spring
Bump knob
Spool
Spool cover
Guard
Screw
Blade
Screw
Spring washer
Battery
Charger
29
QTY
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
2
1
1
Greenworks Tools
PO Box 1238
Mooresville, NC 28115
TOLL-FREE HELPLINE: 1-855-345-3934
Rev: 00 (08-06-16)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising