Wharfedale Titan 15 User guide

Titan ™

OPERATING MANUAL AND USER GUIDE

Titan™ 8 Passive Titan™ 12 Passive Titan™ 15 Passive

Titan™ 8 Active MKII Titan™ 12D Titan™ 15D

Titan™ Sub A12 Titan™ Sub A15 www.wharfedalepro.com


IMPORTANT WARNINGS & SAFETY INSTRUCTIONS

1. Read these instructions

2. Follow all instructions

3. Keep these instructions

4. Heed all warnings

5. Do not use this apparatus near water

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarised or grounding plug. A polarised plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart and apparatus combination to avoid injury from tip-over.

13. Unplug the apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way including but not limited to power supply cord or plug damage, liquid ingress, foreign objects in the chassis, exposure to rain/moisture or impact damage. In addition the unit must be serviced when you experience any abnormal operation.

15. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not attempt to perform any servicing other than that contained in the operating instructions unless you are qualified to do so. In addition opening the casing will result in your warranty becoming null and void.

16. Do not install this apparatus in a confined space such as a book case or similar unit. Good ventilation should be maintained around the apparatus and any vents, air-inlets or fans should not be obstructed by objects such as paper, table-cloths, curtains etc.

17. WARNING: To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture. The apparatus should not be exposed to dripping or splashing and objects filled with liquids, such as vases, should not be placed on the apparatus.

18. WARNING: The mains plug/appliance coupler is used as a disconnect device, the disconnect device shall remain readily operable.

1

Titan ™ Series

ATTENTION: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

19. - This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

- Warning: To reduce the risk of electric shock, do not remove the cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.

- The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.

20. (Protective earthing terminal) The apparatus should be connected to a mains socket outlet with a protective earthing connection.

21. Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use local return and collection systems or contact the retailer where the product was purchased.

They can take this product for safe environmentally friendly recycling.

2


TABLE OF CONTENTS

1..........................................Important Warnings & Safety Instructions

2..........................................Important Safety Information Powered Products

4..........................................Introduction / About the Titan™ Series

4..........................................Titan series overview

5..........................................Features

6..........................................Qubit

7..........................................Setting up / Speaker Placement

7..........................................Connections / Wiring - Passive

8..........................................Rear Panel Layout - Passive

8..........................................Connection Diagram - Passive

11 ..........................................Rear Panel Layout - Active

14..........................................Connection Diagram - Active

15..........................................Rear Panel Layout - Sub A12

16..........................................Connection Diagram - Sub A12

18..........................................Rear Panel Layout - Sub A15

19..........................................Connection Diagram - Sub A15

21..........................................Specifications - Titan™ Passive

22..........................................Specifications - Titan™ Active

24..........................................Specifications - Titan™ Subwoofers

25..........................................Dimensional Drawings - Titan™ 8 / 12

26..........................................Dimensional Drawings - Titan™ 15 / 8A MKII

27..........................................Dimensional Drawings - Titan™ 12D / 15D

28..........................................Dimensional Drawings - Titan™ Sub A12 / A15

29…………………………..…Warranty

3


INTRODUCTION

Wharfedale Pro Titan™ Series is the result of many years of experience in the use, design and manufacturing of professional loudspeaker products. We take great pride in engineering and building every Wharfedale Pro loudspeaker and wish to thank you for entrusting us with your sound.

From the time Gilbert Briggs built his first loudspeaker in 1932, to the present, Wharfedale

Loudspeakers have maintained the same standard of quality in components, workmanship and performance. Wharfedale are one of the few present day manufacturers that design, engineer and build all of our own transducers.

Please take a few minutes to read this manual completely in order to ensure that you get the most out of your Titan™ Series Loudspeaker system.

TITAN™ SERIES OVERVIEW

The Titan Series are powerful, accurate, high quality loudspeaker systems with low distortion that are designed to deliver oustanding performance at a cost effective price point. An Elliptical

Wave Guide (EWG) is perfectly matched to the custom designed HF drivers and provides smooth dispersion in both the horizontal and vertical planes.

The road tough, gas-assist injection moulded polypropylene enclosures are ultra lightweight and include rubberised handles and cable management to make Titan the most user-friendly portable speaker on the market. Threaded rigging points mean that Titan is equally suited to flown applications; a comprehensive range of Wharfedale Pro wall mounting options are also available as optional extras.

Active models feature rear panel power LED’s and a throat mounted LED to make you aware of AC power supply from both the front and rear of the unit. Active models also feature a horn LED defeat switch for less obtrusive aesthetics in applications such as conferencing and A/V presentations.

The BRO™ (Bass Response Optimizer) circuit on the 12D and 15D models helps counteract loss of bass at low levels, similar to a loudness switch on home HiFi amplifiers. In addition our "D" models feature Qubit™ 24-bit 192kHz DSP Processing.

4


FEATURES

Titan Passive

♦ 2-way full range loudspeakers

♦ Low distortion, high power moisture proof woofers

♦ HF compression drivers

♦ 90° x 60° Elliptical Wave Guide (EWG)

♦ DTF™ Dynamic Thermal Filament HF protection

♦ Lightweight, high strength gas-assist injection moulded polypropylene enclosures

♦ Ergonomic rubberised handles

♦ Integral lockable 35mm (1⅜”) pole mount socket

♦ M6 / M8 rigging points

♦ Speakon™ and ¼” jack inputs

Titan Active

♦ Bi-amplified full range loudspeakers

♦ Low distortion, high power moisture proof woofers

♦ HF compression drivers

♦ Qubit™ 24-bit 192kHz DSP processing

♦ Independent LF & HF adaptive dynamics and signal limiting

♦ Per channel volume controls (Master only on 8A MKII)

♦ 2 Band EQ

♦ 90° x 60° elliptical Wave Guide (EWG)

♦ BRO™ Bass Response Optimizer (12D & 15D only)

♦ Horn LED defeat switch

♦ Balanced XLR output for parallel wiring

♦ XLR / ¼” jack combo inputs

♦ Mic / line level input selector

♦ 2 mixable inputs (12D & 15D only)

♦ Stereo RCA inputs (12D & 15D only)

♦ Lightweight, high strength gas-assist injection moulded polypropylene enclosures

♦ Ergonomic rubberized handles

♦ Integral lockable 35mm (1⅜”) pole mount socket

♦ M6 / M8 rigging points

♦ IEC AC receptacle

5


Subwoofer

♦ Low distortion, high power woofers

♦ 2x balanced XLR HPF outputs

♦ 2x summed XLR / ¼” jack combo inputs

♦ Built in signal limiting

♦ Adjustable crossover frequency (SUB 12A only)

♦ -∞to +6dB trim control

♦ 0° / 180° switch

♦ Ergonomic handles

♦ Pole mount socket

♦ IEC AC receptacle

QUBIT™

Qubit brings the power and precision of 24-bit 192kHz DSP processing to the next generation of

Wharfedale Pro Products.

With advanced multi-band dynamic processing and filtering Qubit helps fine tune your system to sound natural and open. Qubit processing optimises the loudspeaker to provide smooth digital crossover points that are perfectly aligned. Protection is offered in the form of true independent adaptive LF and HF signal limiting that helps protect against thermal damage and driver over excursion.

Qubit has an extended frequency response that goes way beyond the capabilities of our hearing, providing an extended phase response that remains linear throughout our natural hearing range.

A Qubit equipped system can reproduce exceptionally natural and accurate transients due to its phase characteristics and perfect time alignment.

6


SETTING UP

1. Ensure the speakers power switch is in the off position (Active models only)

2. Set the level controls to minimum (Fully anticlockwise) (Active models only)

3. Set the EQ controls to 0dB (Active models only)

4. Select mic/line input (Active models only)

5. Connect all signal cables

6. Connect the power cable (Active models only)

7. Switch on source equipment, ensuring that the master level is at minimum

8. Switch on the Titan Loudspeaker (Active models only)

9. Raise the level control on the Titan (Active models only) or external amplifier

10. If the limit LED illuminates lower the level control, if more level is required you will need more speakers. Occasional flashes are acceptable. (Active models only)

11. When powering down your system ensure that the level control (Active models only) has been lowered to minimum before switching off the power

SPEAKER PLACEMENT

The well behaved dispersion characteristics of the Titan series make speaker placement quick and simple.

As with all full range loudspeakers it is recommended to place a Titan above the head level of the audience, as the human body can absorb a huge amount of high frequency energy. Placing the loudspeaker enclosure higher up also helps improve coverage for more even levels over a greater audience area.

Tripod speaker stands, pole mounts, Wall brackets and rigging hardware can be used to elevate the

Titan loudspeaker. Always ensure that any accessories that are used are capable of safely elevating the loudspeaker as incorrect rigging can be dangerous and even fatal. Please refer to the important safety warnings section for more guidelines on rigging and suspending.

Always place your microphones outside the coverage of your front of house speakers to reduce the risk of feedback.

7

Titan™ REAR PANEL LAYOUT

CONNECTION DIAGRAM #1

Titan two channel setup


8


CONNECTION DIAGRAM # 2

Titan mono front of house+stage monitor setup

9

NOTE: This configuration represents a 4 ohm load to each output channel of the amplifier


USING THE Titan WITH A PASSIVE

SUBWOOFER


USING THE Titan™ 8/12/15 IN A

BI-AMP SYSTEM


10


Titan™ 8A MKII / Titan™ 12D / Titan™ 15D

The Loop / Mix Switch

The LOOP/MIX switch allows you to control the signal content going to the XLR OUTPUT jack. In the “LOOP” mode, this switch routes the signal of INPUT B to the line level XLR OUTPUT jack, bypassing the EQ section and volume control. When in the MIX mode, this switch routes the combined (or “mixed”) signals of both INPUT

A and INPUT B to the line level XLR OUTPUT jack. This signal can then be sent to additional powered speakers or powered subwoofers.

8A MKII - REAR PANEL FEATURES

11


Titan™ 12D/15D REAR PANEL LAYOUT

2

7

8

12

1

3

4

5

6

9

10

11

13

14

12


TITAN™ 8A MKII/12D/15D REAR PANEL FEATURES

1.

Heat Sink: The heat sink allows for dissipation of heat built up from the amplifier via air cooling at the rear of the enclosure. (Titan 8A MKII and 15D only)

2. VOLUME for INPUT A and INPUT B: These knobs control the level of each input channel (Controls the master volume on the Titan 8A MKII)

3. HI and LOW EQ (equalization) controls: These knobs control the equalization of the overall output signal providing +/- 10dB of gain for each band.

4. Remote Control: This Pheonix connector can be used to control the volume with an applied voltage.

5. 90Hz Monitor Filter switch: Used to reduce bass buildup due to half space loading.

6. Horn LED defeat switch: Switches off the horn power LED for discrete applications.

7. RCA L / R (Left and Right) input jacks: These jacks allow input of a stereo signal (left and right). The signal is actively combined or “summed” providing a mono signal to the amplifier.

8. GAIN selection switch: This switch selects the proper gain structure for INPUT A. If a microphone is connected to INPUT A, use mic mode (up). If the signal source is anything other than a microphone (playback device, keyboard or mixer output, for instance) use the line mode (down) .

9 & 10. POWER ON / OFF switch, POWER ÓN´ indicator LED and LIMIT indicator LED: The switch: turns the power on and off. The bracketed LED to the left of the POWER switch illuminates when the power switch is in theÓN´ position. The LIMIT LED illuminates when the signal limiter is limiting the level of the signal to prevent distortion and overload.

11. Output source “LOOP / MIX” switch: In the “LOOP” mode, this switch routes the signal of INPUT B to the line level XLR OUTPUT jack, bypassing the EQ section and volume control. When in the MIX mode, this switch routes the combined (or “mixed”) signals of both INPUT A and INPUT B to the line level XLR OUTPUT jack.

12. XLR / ¼” COMBO input jacks for INPUT A and INPUT B: These convenient jacks allow XLR or ¼” balanced input connections to INPUT A and INPUT B

13. POWER cord receptacle: This is a receptacle for a standard IEC, three prong, grounded AC electrical connection cord. Be sure that you are plugging into the correct source voltage that matches what is indicated just below the power cord jack.

14.

XLR line level OUTPUT jack: This jack provides a balanced line level output for connection to additional

Titan™ ACTIVES, powered subwoofers or amplifiers.

13

Titan™12D / 15D CONNECTION DIAGRAM # 1

Basic microphone / playback hookup


Titan™12D / 15D CONNECTION DIAGRAM # 2

Connecting two Titan™ ACTIVE speakers together

14


TITAN™ SUB A12 REAR PANEL FEATURES

1. HEAT SINK

2. VOLUME CONTROL

Cooling fins for amplifier. Do not obstruct.

Adjusts the volume.

3. INPUT L

4. INPUT R

5. OUTPUT R

6. OUTPUT L

Balanced line level input via a XLR/ ¼” combo connector.

Balanced line level input via a XLR/ ¼” combo connector.

Balanced male XLR connector provides output HIGHPASS signal.

Balanced male XLR connector provides output HIGHPASS signal.

7. POWER SOCKET

8. LIMIT LED

POWER LED

9. POWER SWITCH

10. PHASE SWITCH

This is the connection for the IEC AC power connector.

LED indicator illuminates when the signal limiting function is activated.

LED indicator illuminates when the unit is powered up.

Turns the power on and off to the subwoofer amplifier module.

Selects the polarity of the signal being sent to the subwoofer.

0° selects the signal polarity as it appears at the input.

The 180° selection inverts the polarity of the signal.

Adjustable 80Hz/100Hz/120Hz/150Hz/180Hz/200Hz.

11. CROSSOVER

FREQUENCY

CONTROL

15

Titan™ Sub-A12 CONNECTION DIAGRAM # 1

TWO CHANNEL SYSTEM WITH HIGHPASS OUTPUT


16



USING TWO Titan™ Sub-A12 WITH

TWO POWER SPEAKERS

17


Titan™ Sub-A15 - REAR PANEL FEATURES

1. INPUT A - Balanced line level input via a XLR / ¼” combo connection.

2. OUTPUT A - Balanced male XLR connection provides “THRU” or HIGHPASS signal (depending on switch setting).

3. SPEAKER LEVEL INPUT - Allows for connection of an external amplifier to use the Titan™ Sub-A15 as a passive subwoofer.

NOTE: Disconnect the power cord when using the Titan™ Sub-A15 in this mode.

4. INPUT B - Balanced line level input via a XLR / ¼” combo connection.

5. OUTPUT B - Balanced male XLR connection provides output “THRU” or HIGHPASS signal (depending on switch setting).

6. HEATSINK - Cooling fins for amplifier. Do not obstruct.

7. VOLUME CONTROL - Adjusts volume level of the subwoofer.

8. THRU / HIGHPASS SWITCH - Selects the signal type that is routed to the OUTPUT jacks, “THRU” sends the unprocessed signal to the outputs. “HIGHPASS” filters the signal at 100Hz to the outputs.

9. PHASE SWITCH - Selects the polarity of the signal being sent to the subwoofer. 0° selects the signal polarity as it appears at the input. The “180°” selection inverts the phase of the signal.

10. LIMIT LED - LED indicator illuminates when the singal limiting function is activated.

11. POWER LED - LED indicator illuminates when the unit is powered up.

12. POWER SOCKET - This is the connection for the IEC AC power connector.

13. POWER SWITCH - Turns the power on and off to the subwoofer amplifier module.

1

2

3

4

5

INPUT A

OUTPUT A

SPEAKER

LEVEL INPUT

INPUT B

OUTPUT B

A

INPUT

(B A L A N C E D )

OUTPUT

(B A L A N C E D )

SPEAKER

LEVEL IN

THRU

(100Hz)

HIGHPASS

B

(B A L A N C ED )

INPUT

(B A L A N C ED )

OUTPUT

I

0

I

_

I I

MAX

VOLUME

0°

PHASE

180°

WWW.WHARFEDALEPRO.COM

D O N O T O PE N

!

WARNING: SHOCK HAZARD DO NOT OPEN

AVIS: RISQUE DE CHOC ELECTRIQUE

-NE PAS OUVRIR

LIMIT N 2082

ON

OFF

POWER AC 220-240V~50Hz 400W

FUSE T4AL250V

SERIALNUMBER

HEATSINK

VOLUME

CONTROL

THRU/HIGHPASS

SWITCH

PHASE SWITCH

LIMIT LED

POWER LED

POWER SOCKET

POWER SWITCH

8

9

10

11

12

13

6

7

18



TWO CHANNEL SYSTEM WITH

HIGHPASS OUTPUT

19

NOTE: This same connection configuration can be used with OUTPUT A and B used in a fullrange mode when the THRU/HIGHPASS switch is in the "THRU" (up) position.

CONNECTION DIAGRAM # 2

USING TWO Titan™ Sub-A15's WITH

TWO POWERED SPEAKERS


20


SPECIFICATIONS - Titan™ PASSIVE SERIES

Loudspeaker Type:

Frequency Response (+/–3dB):

Sensitivity (1W@1M):

Peak SPL:

HF Coverage (H x V):

System Impedance:

POWER (WATTS)

Continuous:

Music:

Peak:

LF DRIVER

Size:

Coil Size:

HF DRIVER/ HORN

Coil Size:

Exit Size:

Diaphragm Material:

HF Driver Protection:

Long-Throw EQ Compensation:

Horn Type:

Throat Size:

CROSSOVER

Type/Frequency/Filter:

ENCLOSURE

Shape/ Material:

Rigging:

COLOURS

OUTPUT CONNECTORS

DIMENSIONS/WEIGHTS

Weight:

Dimensions (H x W x D):

Titan™ 8

8" 2-way

70 - 20kHz

96dB

124dB

90˚ x 60˚

8 ohm

150W

300W

600W

203mm/ 8"

38.86mm / 1.53"

Compression Driver

25mm/1"

30mm/1.2"

Cloth

Bulb

N/A

EWG™ - Elliptical Waveguide

25mm/1"

2-way 2.4KHz / Linkwitz-Riley

Trapezoidal/ Polypropylene

(8) M6 threaded rigging points

+ (4) M6 threaded rigging points on bottom in Omnimount®

30.0-type footprint + Speaker polemount receptacle with lock screw

+ 1 built-in carry handle + Optional wall-mount bracket + (Optional dual-unit array speaker stand hardware)

Grey or Black or White

2 x 1/4" jacks + 2 x NL4

5.5kg / 12.1lbs

396 x 266 x 221mm/

15.59" x 10.47" x 8.7"

Titan™ 12

12" 2-way

55 - 20kHz

98dB

128dB

90˚ x 60˚

8 ohm

250W

500

1000

305mm/ 12"

64.26mm / 2.5"

Compression Driver

44mm/1.75"

25mm/1"

Titanium

DTF™ Dynamic Thermal Filament

3dB boost (long-throw) / Flat

(near-field)


25mm/1"





60.0-type footprint + Speaker pole-mount receptacle with lock screw + Optional wall-mount bracket + (Optional dual-unit array speaker stand hardware)


2 x 1/4" jacks + 2 x NL4

12kg / 26.4lbs

556 x 384 x 312mm/

21.88" x 15.1" x 12.3"

Titan™ 15

15" 2-way

50 - 20kHz

97dB

129dB

90˚ x 60˚

8 ohm

400W

800W

1600W

381mm/ 15"

75mm / 3.0"

Compression Driver

51mm/ 2.0"

25mm/1"

Titanium

DTF™ Dynamic Thermal Filament

N/A


25mm/1"





60.0-type footprint + Speaker pole-mount receptacle with lock screw + Optional wall-mount bracket + (Optional dual unit array speaker stand hardware)


2 x 1/4" jacks + 2 x NL4

22kg / 48.4lbs

708.3 x 477.8 x 401.77mm/

27.9" x 18.8" x 15.8

21


SPECIFICATIONS - Titan™ ACTIVE SERIES

System Type

Frequency Response (+/-3dB)

Low Frequency Driver (mm/in.)

High Frequency Driver

Exit Size (mm / inches)

Dispersion (H x V)

Amplifiers

Low Frequency (Class D)

High Frequency (Class D)

Electronic Crossover:

Crossover Frequency

Equalization:

Subsonic Filter

Amplifier Protection

Power On

Thermal

Low Line Voltage Shut Down

Driver Protection

DC Protection

Short Protection

Clip Limiter:

Limiter Indicator

Power Indicator

Titan™ 8 ACTIVE MK II

Active 8” 2-way Bi-Amplified

70-20kHz

205mm / 8”

Compression Driver

30mm / 1.2”

90° x 60°

Rated 150W continuous, 300W Peak

Rated 30W continuous, 60W Peak

24dB per octave Linkwitz-Riley

2.4kHz

High (±10dB) 10kHz Shelving

Low (±10dB) 100Hz Shelving

30Hz, Second -order filter

Power switch on / off mute

Amplifier shutdown, auto reset

< 80VAC

Independent LF and HF limiters

Yes

Yes

Turns on approx 150W output

Red LED

Green LED

Titan™ 12 D


55-20kHz

305mm / 12”

Titanium Compression Driver

25mm / 1"

90° x 60°

Titan™ 15 D


50-20kHz

381mm / 15”

Titanium Compression Driver

25mm / 1"

90° x 60°

Rated 250W continuous, 500W Peak Rated 350W continuous, 700W Peak

Rated 50W continuous, 100W Peak Rated 70W continuous, 140W Peak

24dB/octave Linkwitz-Riley 24dB/octave Linkwitz-Riley

2.3kHz




1.8kHz






60% Nominal line voltage


Yes

Yes


Red LED

Green LED





Yes

Yes


Red LED

Green LED

22


SPECIFICATIONS - Titan™ ACTIVE (Con't)

Inputs

Input A – type

Input Sensitivity

Maximum Input Level

Input Connector

Input Impedance

Maximum Input Level

Input B – type

Input Sensitivity

Maximum Input Level

Input Connectors

Line Output

Impedance:

Sensitivity

AC Power details

Power Supply

AC Power Options

Power On Indicator

Rigging / Bracket / Mounting

Options

Enclosure Material

Colours

Dimensions H x W x D (mm)

Dimensions H x W x D (in)

Net Weight (kg / lbs)

Gross Weight (kg / lbs)

Titan™ 8 ACTIVE MKII

Switchable balanced mic or line level input

Mic: -47dBu (-49.2dBv or

3.4mVrms)

Line: 0dBu (-2.2dBv or 0.775Vrms)

+22dBu

XLR - 1/4” Combo jack

Balanced: 20kΩ -

Unbalanced: 10kΩ

+22dBu

N/A

N/A

+22dBu

Combo jack: 1/4" - XLR

Switchable LOOP / MIX

Balanced Male XLR Connector

Balanced: 1k ohm Unbalanced:

500 ohm

0dBu (-2.2dBv or 0.775Vrms)

High Efficiency Switching Mode

Power Supply

AC100~240V, 50 / 60Hz

Green LED

8 M6 threaded inserts including 4

M6 threaded inserts on bottom in OmniMount

30.0-type footprint

Pole-mount receptacle with lock screw

1 carry handles

Optional wall-mount bracket

Injection Moulded Polypropylene

Grey or white or black

396 x 266 x 221

15.6 x 10.5 x 8.7

6.25kg / 13.75lbs

8.15kg/ 17.93lbs

Titan™ 12 D Titan™ 15 D



7.75mVrms)



7.75mVrms)

Line: 0dBu (-2.2dBv or 0.775Vrms) Line: 0dBu (-2.2dBv or 0.775Vrms)

+22dBu +22dBu


Balanced: 10kΩ -


Balanced: 10kΩ -

Unbalanced: 5kΩ

+22dBu

Line level input

XLR - 1/4” Combo jack: 0dBu (-2.2

dBv or 0.775Vrms)

RCA: 0dBu (-2.2dBv or

0.775Vrms)

Unbalanced: 5kΩ

+22dBu

Line level input

XLR - 1/4” Combo jack: 0dBu (-2.2

dBv or 0.775Vrms)

RCA: 0dBu (-2.2dBv or

0.775Vrms)

+22dBu

Combo ja ck: 1 / 4" - XLR / Summe d dual RCA jacks

Switchable LOOP / MIX Balanced

Male XLR

Balanced: 200 ohm Unbalanced:

100 ohm


+22dBu

Combo jack: 1/4" - XLR /

Summed dual RCA jacks

Switchable LOOP / MIX Balanced

Male XLR

Balanced: 200 ohm Unbalanced:

100 ohm



Power Supply

AC100~120V / 220~240 V, 50 /

60Hz

Green LED

10 M8 threaded inserts including

4 M8 threaded inserts on bottom in OmniMount

60.0-type footprint


2 carry handles (one on each side)



Black

556 x 384 x 312

21.9 x 15.1 x 12.3

12.4kg / 27.28lbs

15.5kg / 34.lbs


Power Supply

AC100~120V / 220~240 V, 50 /

60Hz

Green LED

10 M8 threaded inserts including

4 M8 threaded inserts on bottom in OmniMount

60.0-type footprint


2 carry handles (one on each side)



Black

708.3 x 477.8 x 401.8

27.9" x 18.8" x 15.8

22.9kg / 50.38lbs

27.7kg / 60.94lbs

23


SPECIFICATIONS - Titan™ SUB SERIES

System Type

Frequency Response (+/-3dB)

Enclosure Material

Enclosure Colour

Frame material

Size (mm / inches)

Coil Size (mm / inches)

Impedance

Speaker Pole Adapter

Inputs A & B - Type / Connection

Output A & B Type / Connection

Input Sensitivity

High Pass Frequency Selection

Phase Switch Selection

Crossover Frequency (HZ)

Speaker Level Input Impedance

Speaker Level Input Connection

Amplifier Power: Continuous

Amplifier Power: Peak

Power On Indicator

Power On Protection

Thermal Protection

Low Line Voltage Shut Down

Driver Protection

DC Protection

Short Protection

Clip Limiter:

Limiter Indicator

Power Indicator

Dimensions H x W x D: (mm)

Dimensions H x W x D (in)

Weight (Net) kg / lbs

TITAN™ Sub-A15

Band-pass subwoofer

45-150Hz

18mm Plywood

Grey or Black

Die-cast aluminium frame

404mm / 15”

75 / 3”

4 ohm

Yes

Balanced Line Level inputs via two combo connectors


0.56V

100Hz

0° / 180°

150

1/4” TS Phone input

4Ω

400W

600W

LED




Independent LF limiters

Yes

Yes


Red LED

Blue LED

630.0 x 478.0 x 640.0

24.8 x 18.8 x 25.2

45.48kg / 100.0lbs

Titan™ Sub-A12

Reflex subwoofer

55-200Hz

15mm MDF

Grey or Black steel frame

305mm / 12”

64.26mm / 2.5”

4 ohm

Yes



0.37V

150Hz

0° / 180°

80/ 100/ 120/ 150/ 180/ 200

(adjustable)

250W

500W

LED




Independent LF limiters

Yes

Yes


Red LED

Blue LED

360.0 x 493 x 431.0

14.2 x 19.4 x 16.9

22.31kg /49.0lbs

24


DIMENSIONS

25

DIMENSIONS


26


DIMENSIONS

12.28"

312mm

21.88"

556mm

15.11"

384mm

12.28"

312mm

7.1"

180mm

15.83”

402mm

27.87”

708mm

15.83”

402mm

18.81”

478mm

27

DIMENSIONS


28


29

WHARFEDALE PRO LIMITED WARRANTY

Wharfedale Pro products are warranted of manufacturing or material defects for a period of one year from the original date of purchase. In the event of malfunction, contact your authorized Wharfedale Pro dealer or distributor for information.

*Be aware that warranty details may differ from country to country. Contact your dealers or distributor for information. These terms do not infringe your statutory rights.

Wharfedale Professional

IAG HOUSE, Sovereign Court, Ermine Business Park Huntingdon, Cambs, PE29 6XU, England www.wharfedalepro.com

Wharfedale Professional reserves the right to alter or improve specifications without notice.

All rights reserved © 2010 Wharfedale Pro. Wharfedale Pro is a member of the International Audio Group (IAG).

Wharfedale Titan 15 User guide

Titan ™

OPERATING MANUAL AND USER GUIDE

Titan™ 8 Passive Titan™ 12 Passive Titan™ 15 Passive

Titan™ 8 Active MKII Titan™ 12D Titan™ 15D

Titan™ Sub A12 Titan™ Sub A15 www.wharfedalepro.com

IMPORTANT WARNINGS & SAFETY INSTRUCTIONS

TABLE OF CONTENTS

INTRODUCTION

TITAN™ SERIES OVERVIEW

FEATURES

Titan Passive

Titan Active

Subwoofer

QUBIT™

SETTING UP

SPEAKER PLACEMENT

TITAN™ 8A MKII/12D/15D REAR PANEL FEATURES

Titan™12D / 15D CONNECTION DIAGRAM # 1

TITAN™ SUB A12 REAR PANEL FEATURES

1. HEAT SINK

2. VOLUME CONTROL

3. INPUT L

4. INPUT R

5. OUTPUT R

6. OUTPUT L

7. POWER SOCKET

8. LIMIT LED

POWER LED

9. POWER SWITCH

10. PHASE SWITCH

11. CROSSOVER

FREQUENCY

CONTROL

Titan™ Sub-A12 CONNECTION DIAGRAM # 1

USING TWO Titan™ Sub-A12 WITH

TWO POWER SPEAKERS

TWO CHANNEL SYSTEM WITH

HIGHPASS OUTPUT

SPECIFICATIONS - Titan™ PASSIVE SERIES

SPECIFICATIONS - Titan™ ACTIVE SERIES

SPECIFICATIONS - Titan™ ACTIVE (Con't)

SPECIFICATIONS - Titan™ SUB SERIES

DIMENSIONS

DIMENSIONS

DIMENSIONS

DIMENSIONS

WHARFEDALE PRO LIMITED WARRANTY

Related manuals

Wharfedale Pro

Titan 15D

Wharfedale Pro

Titan Sub A15 MKII

Wharfedale

Wharfedale Pro

Titan 15D

Wharfedale Pro

Titan 12 ACTIVE

Wharfedale Pro

Titan 8

Wharfedale Pro

Titan 8 Passive

Wharfedale

Titan 8 Active MKII

Wharfedale Pro

8 Passive

Wharfedale

Titan 15

Wharfedale Pro

Titan 12D

Wharfedale

Link-800