www.collegehillshonda.com
Accessory Application Publications No.
VERSION 1
INSTALLATION
INSTRUCTIONS
WING SPOILER
P/N 08F13-TBA-100
2016 CIVIC
4-DOOR
Issue Date
OCT 2015
Spoiler harness
PARTS LIST
Wing spoiler
10 Wire ties
(Some may not be used)
Left trunk spring (marked yellow)
2 Aluminum tapes
Right trunk spring (marked red)
2 Alcohol swabs
Template
4 Flange nuts
4 Seals
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
AII02278-02 (1510)
08F13-TBA-1000-90
1 of 11
www.collegehillshonda.com
INSTALLATION TOOLS AND SUPPLIES REQUIRED
Eye protection (face shield, safety goggles, etc.)
Center punch
Drill
File
Touch-up paint
Felt-tip pen
Isopropyl alcohol
Shop towel
Tape
Masking tape
Heavy gloves
Diagonal cutters
Ratchet
10 mm Socket
Torque wrench
10 mm Open end wrench
High-quality paste wax
The following tools are available through the Honda Tool and Equipment Program. On the iN, click on: Service >
Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857.
• Trunk Spring Tool (T/N 07AAF-T2AA200)
• Rotabroach Hole Cutting Kit (T/N BLR11201SO)
• Trim Tool Set (T/N SOJATP2014)
Illustration of the Wing Spoiler on the Vehicle
Customer Information: The information in this
installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
NOTE:
• Be careful not to damage the paint finish.
• This wing spoiler kit should be installed only if the ambient air temperature is 15° C (60° F) or above.
• Clean and wax the areas to be covered with a highquality paste wax.
• To allow the adhesive to cure, do not wash the vehicle for 24 hours. Please advise the customer.
1.
Disconnect the negative cable from the battery.
2.
Open the trunk lid. Remove the trunk lid trim panel.
TRUNK LID
9 CLIPS
SPOILER
HARNESS
WING SPOILER
TRUNK LID
TRIM PANEL
2 of 11
AII02278-02 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
Installing the Wing Spoiler
3.
Close the trunk lid. To prevent metal shavings from falling into the trunk, apply masking tape to the trunk lid and the inner taillight as shown.
5.
Using a felt-tip pen, mark the trunk lid through the template at the locations shown.
FELT-TIP PEN
TRUNK LID
TRUNK LID
TAPE
INNER
TAILLIGHT
TEMPLATE
INNER
TAILLIGHT
TAPE
4.
Place the template on the left side of the trunk lid, and align the template with the trunk lid as shown.
Tape the template to the trunk lid with masking tape.
TEMPLATE
SECTION VIEW
Align.
Align the edge of the template with the edge of the trunk lid.
TRUNK LID
MASKING
TAPE
3 MARKS
6.
Remove the template.
7.
Turn the template over. Place the template on the right side of the trunk lid, and align the template with the trunk lid as shown. Tape the template to the trunk lid with masking tape.
TRUNK LID
MASKING
TAPE
Align the edge of the template with the edge of the trunk lid.
TEMPLATE
SECTION VIEW
Align.
TRUNK LID
TRUNK LID
TEMPLATE
INNER
TAILLIGHT
Align the edge of the template with the edge of the inner taillight.
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
AII02278-02 (1510)
Align the edge of the template with the edge of the inner taillight.
INNER
TAILLIGHT
TEMPLATE
3 of 11
www.collegehillshonda.com
8.
Using a felt-tip pen, mark the trunk lid through two outboard holes in the template.
NOTE: Do not mark the inboard hole.
11. While wearing eye protection, use an 8 mm
Rotabroach to drill the four outboard center-punched marks. Drill perpendicular to the trunk lid.
TRUNK LID
SECTION VIEW
FELT-TIP PEN
Drill perpendicular.
DRILL
(8 mm ROTABROACH)
TEMPLATE
TRUNK
LID
DRILL
(8 mm
ROTABROACH)
Do not mark.
2 MARKS
9.
Remove the template.
10. Using a center punch, punch the center of all five marks.
NOTE: If using an automatic center punch, set it to the minimum setting.
TRUNK LID
CENTER PUNCH
2 MARKS
4 MARKS
TRUNK LID
4 of 11
3 MARKS
AII02278-02 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
12. While wearing eye protection, use a 10 mm
Rotabroach to drill the remaining center-punched mark. Drill perpendicular to the trunk lid.
15. Remove the adhesive backings from the four seals, and attach the seals to the holes in the trunk lid.
TRUNK LID
Drill perpendicular.
SECTION
VIEW
DRILL
(10 mm ROTABROACH)
MARK
(Drill only the left driver’s side.)
4 SEALS
4 ADHESIVE
BACKINGS
(Remove.)
TRUNK LID
TRUNK LID
13. Remove the tape installed in step 3. Remove all
burrs and metal shavings with a file, and apply touch-up paint to the edges of the holes.
14. Using an alcohol swab, thoroughly clean the trunk lid where the wing spoiler will attach.
TRUNK LID
Clean with an alcohol swab.
2 HOLES,
8 mm
2 HOLES, 8 mm
16. Remove the adhesive backings from the other side of the four seals, and route the wing spoiler harness down through the 10 mm hole you just drilled. Seat the grommet in the 10 mm hole.
NOTE: Make sure to the grommet is secured properly.
WING SPOILER
TRUNK LID
WING
SPOILER
HARNESS
Clean with an alcohol swab.
2 ALCOHOL SWABS
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
AII02278-02 (1510)
4 ADHESIVE
BACKINGS
(Remove.)
GROMMET
10 mm HOLE
5 of 11
www.collegehillshonda.com
17. Remove the two adhesive backings from the wing spoiler.
20. Open the trunk lid. Install the four flange nuts on the wing spoiler studs, two on each side.
WING SPOILER
2 ADHESIVE
BACKINGS
(Remove.)
4 STUD
BOLTS
4 STUDS
TRUNK LID
4 FLANGE NUTS
Torque: 8.8 N·m
(6.5 lbf·ft)
4 HOLES,
8 mm
TRUNK LID
18. Position the wing spoiler on the trunk lid by inserting the four stud bolts into the 8 mm holes in the trunk lid.
19. Hold the wing spoiler firmly against the trunk lid over the adhesive tapes with the palm of your hand for
30 seconds.
6 of 11
AII02278-02 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
Installing the Trunk Springs
21. Push the tabs, and pull down the left and right seatback release levers to release the hooks. Move the left and right seat-back release levers out of your way.
22. Remove the center clip from the left and right trunk springs.
CENTER
CLIP
LEFT
TRUNK SPRING
SEAT-BACK
RELEASE LEVER
HOLE
RIGHT
TRUNK SPRING
Push.
TAB
HOOK
VEHICLE
PANEL
LEFT SEAT-BACK
RELEASE LEVER
RIGHT SEAT-BACK
RELEASE LEVER
(if equipped)
23. With an assistant holding the trunk lid open, remove the right trunk spring from the slider using the trunk spring tool. Wear gloves to protect your hands, and push down on the trunk spring tool slowly and carefully.
RIGHT
TRUNK SPRING
SLIDER
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
AII02278-02 (1510)
TRUNK
SPRING
TOOL
7 of 11
www.collegehillshonda.com
• Remove the right trunk spring from the right hinge bracket.
RIGHT
HINGE
BRACKET
25. Install the new trunk springs in the reverse order of removal:
• Install the yellow marked trunk spring in the slot on the right (passenger’s side) hinge bracket and to the left (driver’s side) hinge arm.
• Install the red marked trunk spring in the slot on the left (driver’s side) hinge bracket and to the right (passenger’s side) hinge arm.
• Wearing gloves rotate the trunk spring tool as you pull it towards you.
CAUTION: Be careful when installing the trunk spring
as they could repel with strong force and cause injury.
NEW TRUNK
SPRING
HINGE
BRACKET
RIGHT
TRUNK SPRING
(Discard.)
TRUNK SPRING TOOL
24. Repeat step 23 on the left side of the vehicle.
RIGHT
HINGE
BRACKET
LEFT
HINGE
BRACKET
NEW RIGHT
TRUNK
SPRING
Marked red
NEW LEFT
TRUNK
SPRING
Marked yellow
8 of 11
AII02278-02 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
26. Install the center clip to the trunk springs.
CENTER
CLIP
NEW LEFT
TRUNK SPRING
28. Unplug the vehicle 2-pin connector from the high-mount brake light connector, and plug the vehicle 2-pin connector into the spoiler harness 2-pin connector.
NEW RIGHT
TRUNK SPRING
HIGH-MOUNT
BRAKE LIGHT
CONNECTOR
SPOILER HARNESS
2-PIN CONNECTOR
VEHICLE
2-PIN CONNECTOR
VEHICLE
2-PIN
CONNECTOR
Clean with isopropyl alcohol.
VEHICLE
PANEL
Routing the Spoiler Harness
27. Route the spoiler harness through the holes in the vehicle panel as shown.
HOLE
SPOILER
HARNESS
HOLE
SPOILER
HARNESS
2 ALUMINUM
TAPES
29. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle panel where the aluminum tapes will attach.
30. Secure the 2-pin connectors and spoiler harness to the vehicle panel with two aluminum tapes.
VEHICLE
PANEL
SPOILER HARNESS
2-PIN CONNECTOR (SMALL)
SPOILER HARNESS
2-PIN CONNECTOR
(LARGE)
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
AII02278-02 (1510)
9 of 11
www.collegehillshonda.com
31. Secure the spoiler harness to the vehicle harness with two wire ties.
NOTE: Do not secure the wire tie to the trunk opener cable.
32. Plug the spoiler harness 2-pin connector into the wing spoiler harness 2-pin connector.
WIRE TIE
(with tweeter)
VEHICLE HARNESS
(with tweeter)
WING
SPOILER
HARNESS
SPOILER
HARNESS
TRUNK
OPENER CABLE
(Do not secure.)
VEHICLE
HARNESS
WING SPOILER
HARNESS
2-PIN CONNECTOR
3 WIRE
TIES
VEHICLE
HARNESS
WIRE TIE
SPOILER HARNESS
TRUNK
OPENER CABLE
(Do not secure.)
SPOILER HARNESS
2-PIN CONNECTOR
33. Secure the 2-pin connectors, wing spoiler harness, and spoiler harness to the vehicle harness with three wire ties.
NOTE: Do not secure the wire ties to the trunk opener cable.
10 of 11
AII02278-02 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
34. Secure the spoiler harness to the vehicle harness with five wire ties.
NOTE: Do not secure the wire ties to the trunk opener cable.
SPOILER
HARNESS
TRUNK
OPENER
CABLE
SECTION
VIEW
LEFT
HINGE
ARM
VEHICLE
HARNESS
LEFT HINGE
ARM
WIRE
TIE
VEHICLE
HARNESS
5 WIRE
TIES
SPOILER
HARNESS
TRUNK
OPENER CABLE
(Do not secure.)
35. Check that all wire harnesses are routed properly and all connectors are plugged in.
36. Install all removed parts.
37. Connect the negative cable to the battery.
38. Press and hold the audio unit power button for 2 seconds to restore the audio and navi (if equipped) system functions.
39. Reset the clock (on vehicles without navigation).
Check the Operation of the Wing Spoiler
40. Press the brake pedal, and check that the spoiler brake light comes on.
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
AII02278-02 (1510)
11 of 11
