Avaya C360 Quick Start Guide

Avaya C360 Quick Start Guide

Quick Start for Hardware

Installation

Avaya C360 Converged Stackable

Switches

10-300616

Issue 2

September 2005

DO0827 Rev. A

Copyright 2005, Avaya Inc.

All Rights Reserved

Notice

Every effort was made to ensure that the information in this document was complete and accurate at the time of printing. However, information is subject to change.

Warranty

Avaya Inc. provides a limited warranty on this product. Refer to your sales agreement to establish the terms of the limited warranty. In addition, Avaya’s standard warranty language as well as information regarding support for this product, while under warranty, is available through the following Web site: http://support.avaya.com

.

Disclaimer

Avaya is not responsible for any modifications, additions or deletions to the original published version of this documentation unless such modifications, additions or deletions were performed by Avaya. Customer and/or End User agree to indemnify and hold harmless Avaya, Avaya's agents, servants and employees against all claims, lawsuits, demands and judgments arising out of, or in connection with, subsequent modifications, additions or deletions to this documentation to the extent made by the Customer or End User.

How to Get Help

For additional support telephone numbers, go to the Avaya support Web site: http://support.avaya.com

. If you are:

Within the United States, click the Escalation Management link. Then click the appropriate link for the type of support you need.

Outside the United States, click the Escalation Management link. Then click the International Services link that includes telephone numbers for the international Centers of

Excellence.

Standards Compliance

Avaya Inc. is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Avaya Inc. The correction of interference caused by such unauthorized modifications, substitution or attachment will be the responsibility of the user. Pursuant to Part 15 of the Federal

Communications Commission (FCC) Rules, the user is cautioned that changes or modifications not expressly approved by Avaya Inc. could void the user’s authority to operate this equipment.

Product Safety Standards

This product complies with and conforms to the following international

Product Safety standards as applicable:

Safety of Information Technology Equipment, IEC 60950, 3rd Edition, or

IEC 60950-1, 1st Edition, including all relevant national deviations as listed in Compliance with IEC for Electrical Equipment (IECEE) CB-96A.

Safety of Information Technology Equipment, CAN/CSA-C22.2

No. 60950-00 / UL 60950, 3rd Edition, or CAN/CSA-C22.2 No.

60950-1-03 / UL 60950-1.

One or more of the following Mexican national standards, as applicable:

NOM 001 SCFI 1993, NOM SCFI 016 1993, NOM 019 SCFI 1998.

The equipment described in this document may contain Class 1 LASER

Device(s). These devices comply with the following standards:

EN 60825-1, Edition 1.1, 1998-01

21 CFR 1040.10 and CFR 1040.11.

The LASER devices used in Avaya equipment typically operate within the following parameters:

Typical Center Wavelength Maximum Output Power

830 nm - 860 nm -1.5 dBm

1270 nm - 1360 nm

1540 nm - 1570 nm

-3.0 dBm

5.0 dBm

Luokan 1 Laserlaite

Klass 1 Laser Apparat

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposures.

Contact your Avaya representative for more laser product information.

Electromagnetic Compatibility (EMC) Standards

This product complies with and conforms to the following international

EMC standards and all relevant national deviations:

Limits and Methods of Measurement of Radio Interference of Information

Technology Equipment, CISPR 22:1997 and EN55022:1998.

Information Technology Equipment – Immunity Characteristics – Limits and Methods of Measurement, CISPR 24:1997 and EN55024:1998, including:

Electrostatic Discharge (ESD) IEC 61000-4-2

Radiated Immunity IEC 61000-4-3

Electrical Fast Transient IEC 61000-4-4

Lightning Effects IEC 61000-4-5

Conducted Immunity IEC 61000-4-6

Mains Frequency Magnetic Field IEC 61000-4-8

Voltage Dips and Variations IEC 61000-4-11

Power Line Emissions, IEC 61000-3-2: Electromagnetic compatibility

(EMC) – Part 3-2: Limits – Limits for harmonic current emissions.

Power Line Emissions, IEC 61000-3-3: Electromagnetic compatibility

(EMC) – Part 3-3: Limits – Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems.

Federal Communications Commission Statement

Part 15:

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Canadian Department of Communications (DOC) Interference

Information

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme

NMB-003 du Canada.

European Union Declarations of Conformity

Avaya Inc. declares that the equipment specified in this document bearing the “CE” (Conformité Europeénne) mark conforms to the

European Union Electromagnetic Compatibility Directive (89/336/EEC) and Low Voltage Directive (73/23/EEC).

Copies of these Declarations of Conformity (DoCs) can be obtained by contacting your local sales representative and are available on the following Web site: http://support.avaya.com

.

Japan

This is a Class A product based on the standard of the Voluntary Control

Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may occur, in which case, the user may be required to take corrective actions.

To order copies of this and other documents:

Call: Avaya Publications Center

Voice 1.800.457.1235 or 1.207.866.6701

FAX 1.800.457.1764 or 1.207.626.7269

Write: Globalware Solutions

200 Ward Hill Avenue

Haverhill, MA 01835 USA

Attention: Avaya Account Management

E-mail: [email protected]

For the most current versions of documentation, go to the Avaya support

Web site: http://support.avaya.com

.

Contents

Chapter 1: Before you Start . . . . . . . . . . . . . . . . . . . . . . . . . 5

Gathering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Defining the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preparing Contacts you might need . . . . . . . . . . . . . . . . . . . . . . .

Preparing Installation Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preparing Needed Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Choosing the Installation Site . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Building a stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Stack Master election rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6

6

5

5

5

6

Chapter 2: Unpack the Device . . . . . . . . . . . . . . . . . . . . . . . 13

Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Chapter 3: Mount the Device . . . . . . . . . . . . . . . . . . . . . . . . 17

Rack Mounting (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Before you Install the C360 in a Rack . . . . . . . . . . . . . . . . . . . . 18

Wall Mounting (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Chapter 4: Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Connecting to an AC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . 22

AC Power Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Connecting a BUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Supplemental Earthing of the C360 (Optional) . . . . . . . . . . . . . . . . . 24

Post-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Chapter 5: Prepare for Configuration . . . . . . . . . . . . . . . . . . . 25

Establishing a Console Connection . . . . . . . . . . . . . . . . . . . . . . . . . 25

Assigning a C360 IP Stack Address . . . . . . . . . . . . . . . . . . . . . . . . . 26

Establishing a Telnet Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Configuring the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Avaya C360 Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Chapter 6: Device Manager . . . . . . . . . . . . . . . . . . . . . . . . . 31

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Configuring the Device Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Device Manager Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Issue 2 September 2005 3

Contents

Running the Device Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Installing the Java Plug-in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Installing from the C360 Documentation and Utilities CD . . . . . . . . . . . 34

Install from the Avaya Web Site . . . . . . . . . . . . . . . . . . . . . . . . . 35

Install from your Local Web Site . . . . . . . . . . . . . . . . . . . . . . . . . 35

Installing the On-Line Help and Java Plug-In on your Web Site . . . . . . . . . . 35

Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

4 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Chapter 1: Before you Start

Before you install your Avaya C360 Converged Stackable Switch, prepare all the information, resources, and tools that you need during the installation process. Good preparation ensures a smooth installation with the least amount of interruption.

WARNING:

!

!

WARNING:

ONLY TRAINED AND QUALIFIED PERSONNEL SHOULD BE ALLOWED TO

INSTALL OR REPLACE THIS EQUIPMENT.

ADVERTENCIA:

WARNING:

!

!

ADVERTENCIA:

SOLAMENTE PERSONAL CALIFICADO Y ENTRENADO DEBE INSTALAR O

REEMPLAZAR ESTE EQUIPO.

!

!

WARNING:

EQUIPMENT MUST BE CONNECTED TO AN EARTHED MAINS

SOCKET-OUTLET.

!

!

ADVERTENCIA:

EL EQUIPO SE DEBE CONECTAR A UNA TOMA DE TIERRA PRINCIPAL.

ADVERTENCIA:

Gathering Information

Defining the Installation

The C360 can be installed in several different configurations. Before you start the installation, find out what configuration is needed for your site.

Preparing Contacts you might need

Ensure that you have the names and phone numbers of any people you might need to contact at the installation site. This list might include the people responsible for:

Network architecture

Issue 2 September 2005 5

Before you Start

System administration

Site security

Site deliveries

Preparing Installation Files

Ensure that you load the latest versions of the firmware file for the C360. You can download the firmware file needed for your installation from the Avaya Support Web site, at http:// support.avaya.com

.

Preparing Needed Tools

Prepare the tools you need to mount the C360, according to the

Table 1 :

Table 1: Mounting Tools

If you need to mount on...

Prepare these tools

Rack or wall

Flat wall

Uneven wall

Phillips head screwdriver screws to fasten C360 to the wall

16.3" x 18.3" (415 x 465 mm) plywood board

0.8" (20 mm) thick wood screws screws to fasten the C360 to the wall

Choosing the Installation Site

Ensure that the location where you install your C360 fulfills the following requirements:

Cables are away from sources of electrical noise such as:

● radio transmitters

● broadcast amplifiers

6 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Choosing the Installation Site

● power lines

● fluorescent light fixtures

Water or moisture cannot enter the chassis.

Air can flow freely around all sides of the chassis.

The vents on the sides of the chassis are not blocked.

The environmental conditions match the requirements listed in Table 2

.

Table 2: Environmental Requirements

Condition

Ambient temperature

Relative humidity

Weight support

Acceptable values

32 o

to 104 o

F (0 o

to 40 o

C)

5-95% non-condensing

10.8-15 lbs (4.9-6.8 kg)

The power source matches the specifications shown in

Table 3 :

Table 3: Power Requirements

AC Input voltage

Power consumption

C363T

C363T-PWR

C364T

C364T-PWR

AC Input current

C363T

C363T-PWR

C364T

C364T-PWR

100 to 240 VAC, 50 to 60 Hz

60 W

420 W

90 W

760 W

1.3 A

4.2 A

1.3 A

7.6 A

See the Installation and Configuration for the Avaya C360 Converged Stackable Switches,

03-300148, for additional information on environmental requirements.

Issue 2 September 2005 7

Before you Start

Building a stack

Follow the guidelines in this section in order to build a working stack using any combination of the following devices:

P330 series

P330-ML series

G700

C360 series

1. Add only a single box at a time to an existing stack.

Important:

!

Important:

The stack master (also called "stack IP Agent") may fail to preserve existing

"stack configuration" if you will add more than a single device to an existing stack at a time.

- After adding the first box, wait until the stack is functioning fully before adding the next device.

2. Refer to

Table 4

to see which firmware versions can be used in mixed stacks.

For example, if you wish to add a P332G-ML to a stack with C360 4.5 switches, the

P332G-ML switch must have firmware version 4.5.8.

- Upgrade/downgrade the firmware of switches that do not match version in the table.

Tip:

Tip:

It is highly recommended to upgrade/downgrade before connecting the added box to an existing stack.

- Ensure switches of the same type have the same firmware version

8 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Building a stack

Table 4: Firmware Versions Matrix

Required version

Stack without C360

Switch 3.11

3.12

4.0

4.1

P333T

P334T

P333R

3.11.0 3.12.1

4.0.17

4.1.6

3.11.0 3.12.1

4.0.17

4.1.6

3.11.0

3.12.0

4.0.9

4.1.5

P333R-LB

P332MF

3.11.0

3.12.3

4.0.6

4.1.5

3.11.0

3.12.1

4.0.17

4.1.6

P333T-PWR 3.11.0

3.12.1

4.0.17

4.1.6

G700 3.11.0

3.12.1

4.0.17

4.1.6

P334T-ML

P332G-ML

P332GT-ML

C363T

3.11.16

3.11.16

4.0.15

4.1.3

3.11.15

3.11.15

4.0.15

4.1.3

3.11.15

3.11.15

4.0.15

4.1.3

N/A N/A N/A N/A

C364T N/A

C363T-PWR N/A

C364T-PWR N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

4.5

4.5.8

4.5.8

4.5.8

N/A

N/A

N/A

N/A

4.1.6

4.1.6

4.1.5

4.1.5

4.1.6

4.1.6

4.1.6

Stack with C360

4.3

4.5

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

4.5.8

N/A 4.5.8

4.3.12

4.5.14

4.3.12

4.5.14

4.3.12

4.5.14

4.3.12

4.5.14

N/A

N/A

N/A

N/A

N/A

4.1.6

4.1.6

Note:

Note:

Position the C360 switches either at the top or bottom of the stack to ensure mechanical stability.

Issue 2 September 2005 9

Before you Start

Stack Master election rules

Table 5

lists the switches in order of election priority from highest to lowest.

Note:

Note:

If there are two switches with the same firmware version and the same election priority, the switch positioned lower in the stack becomes Stack Master.

Table 5: Stack Master election priority

Switch type Switch mode

C363T, C363T-PWR

C364T, C364T-PWR

C363T, C363T-PWR

C364T, C364T-PWR

P332GT-ML

P332G-ML

P334T-ML

P332GT-ML

Layer 2

Layer 2

Layer 3

Layer 3

Layer 2

Layer 2

Layer 2

Layer 3

P332G-ML

P334T-ML

G700

P333R, P333R-LB

Layer 3

Layer 3

N/A

Layer 2

P333T, P334T, P332MF N/A

P333T-PWR N/A

P333R, P333R-LB Layer 3

P333R-LB Webswitch

Stack Master election priority

12

13

14

15

9

10

11

12

7

8

5

6

3

4

1

2

10 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Stack Master election rules

Figure 1: Example stack elections

C364T-PWR

Layer 3

C363T-PWR

Layer 2

P334T-ML

Layer 3

P333T

G700

1

Figure notes:

1. Stack Master

1

P363T-PWR

Layer 2

P333T

G700

P334T-ML

Layer 3

C363T-PWR

Layer 2

Issue 2 September 2005 11

Before you Start

12 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Chapter 2: Unpack the Device

ELECTROSTATIC ALERT:

!

ELECTROSTATIC ALERT:

Wear an anti-static wrist ground strap whenever you handle components of a

C360. Connect the strap to an approved ground, such as an unpainted metal surface.

Equipment

Open the box that contains the C360, and ensure that it contains the following components and accessories:

One Avaya C360 Switch.

One Accessory Kit that contains:

One 115V 3 Wire

Power Cable

One RJ45 to RJ45

Flat Cable

Issue 2 September 2005 13

Unpack the Device

One RJ45 to DB9F

Adapter

One DB25M Adapter

Two (2) 19"

Rackmount Brackets

Nine (9) M4 Flat

Head Screws

Four (4) 5/16" Round

Head Screws

14 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Documentation

Four (4) Washers

Four (4) stand-off feet

Documentation

Avaya C360 Documentation and Utilities CD

Release Notes

Quick Start for Hardware Installation Avaya C360 Converged Stackable Switches (this document), 10-300616

Issue 2 September 2005 15

Unpack the Device

16 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Chapter 3: Mount the Device

You can mount the C360 in a rack or on the wall.

Rack Mounting (Optional)

The C360 chassis fits in most standard 19-inch racks. It is 1U (44.45 mm, 1.75”) high.

You can mount the Avaya C360 in a standard 19" rack either in “front-mount” or “mid-mount” positions using the brackets supplied with the chassis.

The brackets are symmetric: you can fix either bracket on either side.

Figure 2

shows the two available rack mounting positions:

Figure 2: Front and Mid-Mount Positions

7.9"

(200 mm)

1

2

3

Front

Figure notes:

1. Equipment rack 2. Mid-mount position 3. Front mount position

Issue 2 September 2005 17

Mount the Device

Before you Install the C360 in a Rack

When installing C360 in a rack, ensure that the equipment is positioned such that it will not cause the rack to become unstable or tip over.

Ensure that the combination of equipment in the rack will not cause an overload or overcurrent condition on the power strip being used and/or the customer's branch circuit.

The C360 units weigh a maximum of 15 pounds (6.8 kg). Be careful when installing or removing the C360 product from the rack.

If a power strip is being used in the rack, ensure that it has a reliable earth connection. If the C360 equipment will be plugged directly into a wall outlet, ensure that there is a reliable ground connection at the outlet.

Ensure that the internal rack ambient temperature is within the operating specification limits of the C360.

Ventilation for the C360 is from side to side. Ensure that there is adequate space on each side of the C360 equipment when installed in the rack to allow sufficient airflow.

Place the C360 in the rack as follows:

1. Position the brackets on the C360 as shown in Figure 3 .

Figure 3: C360 Rack Mounting

Figure notes:

1. Front mount position 2. Mid-mount position

1

2

18 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Wall Mounting (Optional)

2. Firmly attach the brackets to the chassis with the screws provided. Use four screws to attach each bracket to the switch.

3. Position the switch in the rack.

4. Fasten the switch in the rack with the screws provided.

Wall Mounting (Optional)

You can fix the C360 to the wall as follows:

CAUTION:

!

CAUTION:

Ensure that the wall and screws can support the weight of the C360 and any installed modules. The maximum weight of a C360 switch is 15 lb. (6.8 kg)

CAUTION:

!

CAUTION:

You must mount the C360 with the ventilation holes facing left and right.

1. Attach the brackets to the C360 as shown in Figure 4 .You can attach the brackets to face

either the top or the bottom of the unit, depending whether you want the top panel or bottom panel of the unit to face the wall.

Issue 2 September 2005 19

Mount the Device

Figure 4: C360 Wall Mounting

Figure notes:

1. Place the unit on the wall.

2. Secure the unit to the wall using two screws on each side. Do not overtighten the screws.

CAUTION:

!

CAUTION:

Ensure that ventilation holes are not obstructed.

20 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Chapter 4: Power Up

Connecting the C360 to the main electrical supply provides power to the switch and for Power over Ethernet (PoE).

WARNING:

!

!

WARNING:

To isolate the switch completely, you must disconnect all power connections (AC plug and DC BUPS power).

ADVERTENCIA:

Note:

!

!

WARNING:

Para aislar el equipo totalmente desconecte todas las conexiones de energía

(Enchufe de CA y fuente de CC del BUPS)

Note:

The C/S: and SW versions on your C360 switches may differ from those shown in

Figure 5

.

Figure 5: Avaya C360 Back Panel

1

2

Figure notes:

1. AC Input 2. DC Input

Issue 2 September 2005 21

Power Up

Connecting to an AC Power Supply

AC Power Cable

The C360 switch is supplied with a North American power cordset. Below are guidelines that should be used when obtaining and/or defining a different cordset to be used with the C360.

The cordsets should be further verified for safety requirements of the particular application by a safety and regulatory professional:

For 200 to 240V applications, the cord must be VDE Certified or Harmonized (HAR), rated

250V, 3-conductor (3rd wire ground), 1.0 mm

2

minimum conductor size. The cord is to be terminated at one end to a VDE Certified/CE Marked IEC 60320, sheet C13 type connector rated 10A, 250V and the other end to a 3-conductor grounding type attachment plug rated at a minimum of 10A, 250V and a configuration specific for the region/country in which it will be used. The attachment plug must bear the safety agency certifications mark(s) for the region/ country of installation.

For North American installations, a UL Listed and CSA Certified 15A branch circuit protective device must be provided in the building AC mains wiring installation for branch circuit protection.

For other installations, a suitable and certified 10A branch protective device must be provided in the building AC mains wiring installation.

Tip:

Tip:

You may order certain cordsets from Avaya.

The C360 is rated 100-240 V~, 50-60 Hz. The maximum input current depends on the specific

C360 model

1. Insert the AC power cord into the power inlet in the back of the unit.

2. Insert the AC plug into the AC power supply.

The unit powers up.

The Avaya C360 performs a self test procedure.

3. Connect the external DC power supply (if available).

22 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Connecting a BUPS

Connecting a BUPS

If you deploy a BUPS with the C360, the APC (Advanced Power Conversion PLC) Front End

AC-DC Power Shelf (model APC-R2400A111) with APC 800W PSUs (models

APC-A0800-085-545-CA1) are to be used.The applied voltage at the C360 BUPS DC terminal block should be from 52 to 55 VDC.

The Isolation must be 1500V RMS with respect to protective ground

Figure 6: Avaya C360 BUPS DC Input Terminal Block

1

2

3

Figure notes:

1. Protective plastic cover 2. BUPS DC input terminals 3. Earthing post

WARNING:

The terminals are marked “+” and “-“.

The size of the two screws in the terminal block is M4.

The pitch between each screw is 9.5mm.

1. Remove the protective plastic cover over the DC inputs by unscrewing the two Phillips screws.

!

!

WARNING:

The conductors to be used for connecting the BUPS to the C360 must be UL

Recognized and CSA Certified and be a minimum of 16 AWG or have a cross-sectional area of 1.0mm

2

.

ADVERTENCIA:

!

!

WARNING:

Los conductores que se utilizarán para conectar la BUPS con el C360 deben ser

Reconocidos por UL, Certificados por CSA y ser como mínimo de 16 AWG o tener un área de sección transversal de 1.0 mm

2

.

2. Connect the power cable to the terminals on the C360 and to the external DC power supply.

Issue 2 September 2005 23

Power Up

WARNING:

!

!

WARNING:

Make sure that you connect the cables between the C360 and the external power supply correctly:

Positive (“+”) to positive (“+”)

Negative (“-“) to negative (“-“)

ADVERTENCIA:

!

!

WARNING:

Asegúrese que las polaridades de los cables entre el C360 y la fuente de alimentación externa estén conectados correctamente:

Positivo ("+") a Positivo ("+")

Negativo ("-") a Negativo ("-")

3. Replace the plastic cover by aligning the holes with the screw receptacles and replacing the two Phillips screws.

Supplemental Earthing of the C360 (Optional)

When connecting a BUPS to the C360, you must also connect a ground wire to the ground stud provided on the rear of the unit. This ground conductor must be green/yellow, a minimum of 16

AWG and be terminated with a lug that is suitable for the M4 stud provided. The other end of the ground conductor is to be terminated to a suitable building ground point such as a cold water pipe.

Post-Installation

The following indicate that you have performed the installation procedure correctly:

Table 6: Post-Installation Indications

Procedure

Powering the C360

Indication

All front panel function LEDs illuminate briefly.

- If the PWR LED blinks once every 1 second, then the BUPS is active and the main PSU is down.

The LINK, SYS and PWR LEDs light

The port LEDs flash

24 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Chapter 5: Prepare for Configuration

This chapter provides information on preparing the C360 for configuration, and discusses the following topics:

Establishing a Console Connection

Assigning a C360 IP Stack Address

Establishing a Telnet Connection

Configuring the Switch

Establishing a Console Connection

This section describes the procedure for establishing switch access between a terminal and the

Avaya C360 switch over the serial port provided on the front panel of the C360 (RJ-45 connector labeled “Console”). For information on the console port pin assignments, refer to the

Avaya C360 Installation and Maintenance User Guide.

Figure 7: Avaya C360 Console Port

1

Figure notes:

1. Console port

Issue 2 September 2005 25

Prepare for Configuration

1. Use the serial cable supplied to attach the RJ-45 console connector to the Console port of the active C360 switch. Connect the DB-9 connector to the serial (COM) port on your PC/ terminal.

- The master C360 is indicated by the SYS LED being ON.

2. Ensure that the serial port settings on the terminal are:

9600 baud

8 bits

1 stop bit no parity.

- If you reset or powered up the switch after connecting and configuring the terminal,

Welcome to C360

appears followed by the Login Name prompt.

- If the login prompt does not appear, press a key on the terminal.

3. Enter the default login: root.

- The Password prompt appears

4. Enter the user level password: root.

- You can now establish a connection to the Router or the Master switch (indicated when the SYS front panel LED is ON) using the Session commands and begin the configuration of module, stack, or router parameters.

Assigning a C360 IP Stack Address

Note:

Note:

All C360 switches are shipped with the same default IP address. You must change the IP address of the master C360 switch in a stack in order to guarantee that the stack has its own unique IP address in the network.

The network management station or a workstation running a Telnet client can establish communications with the stack once this address had been assigned and the stack has been inserted into the network. Use the CLI to assign the C360 stack an IP address and net mask.

To assign a C360 IP stack address:

1. Establish a serial connection by connecting a terminal to the master C360 switch of the stack.

2. When prompted for a Login Name, enter the default name root

3. When you are prompted for a password, enter the password root. You are now in

Supervisor Level.

26 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Establishing a Telnet Connection

4. At the prompt, type:

set interface inband

<vlan> <ip_address> <netmask>

Replace <vlan>, <ip_address> and <netmask> with the VLAN,

IP address, and net mask of the stack.

5. Press Enter to save the IP address and net mask.

6. At the prompt, type reset. Type y and press Enter to reset the stack. After the Reset, log in again as described above.

- At the prompt, type set ip route <dest> <gateway> and replace <dest> and

<gateway>

with the destination and gateway IP addresses.

Establishing a Telnet Connection

Perform the following steps to establish a Telnet connection to the C360 for configuration of

Stack or Router parameters. You can Telnet the Stack Master IP address:

1. Connect your station to the network.

2. Verify that you can communicate with the Avaya C360 by pinging the IP of the Avaya

C360. If there is no response using ping, check the IP address and default gateway of both the Avaya C360 and the station.

Tip:

Tip:

The Avaya C360 default IP address is 149.49.32.134 and the default subnet mask is 255.255.255.0.

3. From the Microsoft Windows taskbar of your PC click Start and then Run (or from the

DOS prompt of your PC), then start the Telnet session by typing: telnet

<C360_IP_address>

For example: telnet 149.49.32.134

4. If the IP Address in the Telnet command is the IP address of the stack, then connection is established with the Switch CLI entity of the Master module.

The “Welcome to C360” screen appears

5. Enter the default name root at the Login name prompt.

6. Enter the User Level password root in lower case letters (do not use uppercase letters) at the Password prompt.

The User level prompt will appear when you have established communications with the Avaya C360.

You can now configure the Avaya C360 stack and change its IP address.

Issue 2 September 2005 27

Prepare for Configuration

Configuring the Switch

This section describes the procedures for the first-time configuration of the Avaya C360. The factory defaults are set out in detail in the tables included in this chapter.

You may configure the Avaya C360 using the text-based Command Line Interface (CLI), the built-in Avaya C360 Device Manager or Avaya Integrated Management.

For instructions on the CLI, see the Avaya C360 Reference Guide.

For instructions on the use of the graphical user interfaces, refer to the C360 Device Manager

User Guide on the Avaya C360 Documentation and Utilities CD.

Avaya C360 Default Settings

The default settings for the Avaya C360 switch and its ports are determined by the Avaya C360 firmware. These default settings are subject to change in newer versions of the Avaya C360 firmware. See the C360 Release Notes for the most up-to-date settings.

Table 7: Default Switch Settings 1 of 2

Function Default Setting

IP address

Subnet Mask

Default gateway

Management VLAN ID

149.49.32.134

255.255.255.0

0.0.0.0

1

Spanning tree Enabled

Bridge priority for Spanning Tree 32768

Spanning tree version

MAC aging

Common spanning tree

Enabled

MAC aging time

Keep alive frame transmission

Network time acquisition

IP multicast filtering

802.1X system-auth-control

5 minutes

Enabled

Enabled, Time protocol

Disabled

Disabled

1 of 2

28 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Tip:

Configuring the Switch

Table 7: Default Switch Settings 2 of 2

Function

802.1X port-control

RADIUS server

Time server IP address

Timezone offset

SNMPv1 communities:

Read-only

Read-write

Trap SNMP

SNMP authentication trap

CLI timeout

System logging

Allowed protocols:

SNMP

Telnet

HTTP

Telnet

ICMP redirect

SSH

Telnet client

Recovery password

User Name/Password

Default Setting

Auto

Disabled

0.0.0.0

0 hours

Public

Public

Public

Disabled

15 Minutes

Disabled

Enabled

Enabled

Enabled

Enabled

Enabled

Disabled

Disabled

Enabled root/root

2 of 2

Tip:

Functions operate in their default settings unless configured otherwise.

Issue 2 September 2005 29

Prepare for Configuration

30 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Chapter 6: Device Manager

This chapter describes the installation procedures for the Device Manager of the Avaya C360.

Overview

The Device Manager provides the following:

Managing and monitoring Power over Ethernet.

Device Configuration - Viewing and modifying the different device configurations.

Virtual LANs - Viewing and editing Virtual LAN information.

Link Aggregation Groups (LAGs) - Viewing and editing LAG information.

Port Redundancy - Setting port redundancy for ports in a C360 Switch.

Port Mirroring - Setting up port mirroring for ports in a C360 Switch.

Trap Managers Configuration - Viewing and modifying the Trap Managers Table.

Switch Connected Addresses - View devices connected to selected ports. Port Security.

Intermodule Redundancy

One pair per stack.

Also operates as a result of a module fault, for example, power failure.

System Requirements

Minimum hardware and operating system requirements are:

Pentium II 400 Mhz-based computer with 128 Mb of RAM.

Screen resolution of 1024 x 768 pixels.

Microsoft Internet Explorer 5 or higher.

Microsoft Windows 2000 Workstation or Windows XP.

Sun Microsystems Java plug-in (supplied on the “Documentation and Utilities” CD). Refer to the Release Notes for the exact version of the Java plug-in.

Issue 2 September 2005 31

Device Manager

Configuring the Device Manager

You can configure several Device Manager parameters using the CLI. These parameters include the time-out and retries parameters, the location of the Web server that provides the help files for the Device Manager, and the Java plug-in required for running the Device

Manager.

Device Manager Commands

The following Device Manager commands are available.

In order to...

Use the following command...

Set the SNMP retries parameter

Set the SNMP time-out parameter set snmp retries set snmp time-out

Set the location of the Web server with the help files and the Java plug-in set web aux-files-url

Display the SNMP retries parameter show snmp retries show snmp time-out Display the SNMP time-out parameter

Display the URL of the Web server with the help files and the Java plug-in show web aux-files-url

Running the Device Manager

Note:

Note:

You should assign an inband or out-of-band interface IP address to the switch before beginning this procedure.

To run the Device Manager:

1. Open your browser.

2. Enter the URL of the switch in the format http://aaa.bbb.ccc.ddd where

aaa.bbb.ccc.ddd

is the inband or outband interface IP address of the switch.

32 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Running the Device Manager

Note:

- The user name is “root”.

- The default password for read-only access is “root”.

- The default passwords for read-write access is “root”.

Note:

The C360 Device Manager passwords are the same as those of the CLI. If you change the passwords of the CLI then those passwords become active for the

Device Manager as well. For further information on the passwords, refer to the

Avaya C360 Installation and Configuration User Guide.

The welcome page is displayed.

Figure 8: The Welcome Page

If you have the Java plug-in installed, the Device Manager automatically opens in a new window, shown in

Figure 9

.

Issue 2 September 2005 33

Device Manager

Figure 9: Device Manager

3. If you do not have the Java plug-in installed, follow the instructions on the Welcome page

for a variety of options to install the plug-in (see Installing the Java Plug-in

).

Installing the Java Plug-in

If the network manager has configured the system, the plug-in should be installed automatically.

Note:

Note:

Ensure that Java or JavaScript is enabled on your Web browser. Please refer to your browser on-line help or documentation for further information.

If the plug-in is not installed automatically, then you have three options for installing it manually:

Installing from the C360 Documentation and Utilities CD

Install from the Avaya Web Site

Install from your Local Web Site

Installing from the C360 Documentation and Utilities CD

To install from the C360 Documentation and Utilities CD:

1. Close all unnecessary applications on your PC.

34 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Installing the On-Line Help and Java Plug-In on your Web Site

2. Insert the Avaya C360 Documentation and Utilities CD in the CD drive.

3. Open Windows Explorer.

4. Browse to the embweb-aux-files\ folder on the CD.

5. Double-click plugin_a_b_c.exe (a, b and c are the version numbers of the plug-in).

6. Follow the on-screen instructions.

Install from the Avaya Web Site

Click the link in the Welcome page labelled “Retrieve it from here ”.

Install from your Local Web Site

Click the appropriate link in the Welcome page.

Note:

Note:

This option is only available if the network manager has placed the files on the local Web server.

Installing the On-Line Help and Java Plug-In on your Web

Site

Tip:

Tip:

This procedure is optional.

Copying the help files and Java plug-in to a local Web server allows users to access the on-line help for the Device Manager and enables automatic installation and maintenance of the Java plug-in the first time the user tries to manage the device.

1. Copy the emweb-aux-files directory from the “Avaya C360 Documentation and

Utilities” CD to your local Web server. Refer to your Web server documentation for full instructions.

2. Define the URL in the C360 using the following CLI command:

set web aux-files-url

//IP address/directory name where //IP address/directory name is the location of the directory from the previous step.

Issue 2 September 2005 35

Device Manager

Documentation

The Device Manager comes with a detailed User’s Guide including a Glossary of Terms and an overview of Data Communications concepts.

36 Quick Start for Hardware Installation: The Avaya C360 Converged Stackable Switch

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project