Sony-CDP-CE375-Service-Manual

Add to my manuals
40 Pages

advertisement

Sony-CDP-CE375-Service-Manual | Manualzz

CDP-CE275/CE375

SERVICE MANUAL

Ver 1.1 2001.07

US Model

Canadian Model

Australian Model

CDP-CE275/CE375

AEP Model

UK Model

E Model

CDP-CE375

Photo: CDP-CE375

Model Name Using Similar Mechanism CDP-CE345

CD Mechanism Type CDM59-5BD27

Base Unit Name

Optical Pick-up Name

BU-5BD27

PXR-104X

SPECIFICATIONS

Compact disc player

Laser

Frequency response

Dynamic range

Harmonic distortion

Outputs

ANALOG

OUT

DIGITAL

OUT

(OPTICAL)

PHONES

(CDP-CE375 only)

Semiconductor laser (

λ

= 780 nm)

Emission duration : continuous

2 Hz to 20 kHz

±

0.5 dB

More than 93 dB

Less than 0.0045%

Jack type

Phono jacks

Optical output connector

Stereo phone jack

Maximum Load output level impedance

2 V Over 10

(at 50 kilohms) kilohms

–18 dBm Wave

10 mW length:

660 nm

32 ohms

General

Power requirements

Mass (approx.)

120 V AC, 60 Hz

Power consumption 11 W

Dimensions (approx.) 430 x 110 x 400 mm

(w/h/d) (17 x 4 3/8 x 15 3/4 in.) incl. projecting parts

5 kg (11 lbs 1 oz)

Supplied accessories

Audio cord (2 phono plugs – 2 phono plugs) (1)

Remote commander (remote) (1) (CDP-CE375 only)

R6 (size AA) batteries (2) (CDP-CE375 only)

Design and specifications are subject to change without notice.

9-873-822-12

2001G0500-1

C

2001.7

Sony Corporation

Home Audio Company

Shinagawa Tec Service Manual Production Group

COMPACT DISC PLAYER

CDP-CE275/CE375

Ver 1.1 2001.07

TABLE OF CONTENTS

1.

SERVICING NOTES

...............................................

3

2.

GENERAL

...................................................................

4

3.

DISASSEMBLY

.........................................................

5

4.

TEST MODE

.............................................................. 10

5.

ELECTRICAL ADJUSTMENTS

......................... 13

6.

DIAGRAMS

6-1. Note for Printed Wiring Boards and Schematic Diagrams ................................................ 15

6-2. Printed Wiring Board – BD Board – ............................. 16

6-3. Schematic Diagram – BD Board – ................................ 17

6-4. Printed Wiring Boards – JUNCTION/SENSOR/

LOADING MOTOR Boards – ........................................ 18

6-5. Schematic Diagram – JUNCTION/SENSOR/

LOADING MOTOR Boards – ........................................ 19

6-6. Printed Wiring Board – MAIN Board – ........................ 20

6-7. Schematic Diagram – MAIN Board – ........................... 21

6-8. Printed Wiring Boards – PANEL Section – .................. 22

6-9. Schematic Diagram – PANEL Section – ....................... 23

6-10. IC Pin Function Description ........................................... 26

7.

EXPLODED VIEWS

................................................ 30

8.

ELECTRICAL PARTS LIST

............................... 35

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety check before releasing the set to the customer:

Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage.

Check leakage as described below.

LEAKAGE TEST

The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.).

Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA

WT-540A. Follow the manufacturers’ instructions to use these instruments.

2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a

VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)

To Exposed Metal

Parts on Set

0.15

µ

F 1.5 k

AC voltmeter

(0.75 V)

Earth Ground

Fig. A.

Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK

0

OR DOTTED

LINE WITH MARK

0

ON THE SCHEMATIC DIAGRAMS

AND IN THE PARTS LIST ARE CRITICAL TO SAFE

OPERATION. REPLACE THESE COMPONENTS WITH

SONY PARTS WHOSE PART NUMBERS APPEAR AS

SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-

LISHED BY SONY.

2

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE

0

SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE

DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ

DE FONCTIONNEMENT. NE REMPLACER CES COM-

POSANTS QUE PAR DES PIÈCES SONY DONT LES

NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

CDP-CE275/CE375

SECTION 1

SERVICING NOTES

NOTES ON HANDLING THE OPTICAL PICK-UP

BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body.

During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts.

The flexible board is easily damaged and should be handled with care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.

HOW TO OPEN THE DISC TABLE WHEN POWER

SWITCH TURNS OFF

Insert a tapering driver into the aperture of the unit bottom, and turn it in the direction of the arrow (to OUT direction).

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

tapering driver table

* To close the disc table, turn the tapering driver in the reverse direction (to IN direction).

This appliance is classified as a CLASS 1 LASER product.

The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.

NOTE FOR MAIN GEAR INSTALLATION

gear, swing gear (RV) gear (U/D)

LASER DIODE AND FOCUS SEARCH OPERATION

CHECK

Carry out the “S curve check” in “CD section adjustment” and check that the S curve waveforms is output three times.

Notes on chip component replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be damaged by heat.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 ˚C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

MODEL IDENTIFICATION

– BACK PANEL –

Model

CDP-CE275: US model

CDP-CE275: Canadian model

CDP-CE275: Australian model

CDP-CE375: US model

CDP-CE375: Canadian model

CDP-CE375: AEP model

CDP-CE375: UK model

CDP-CE375: Australian model

CDP-CE375: E model

CDP-CE375: Singapore model

Part No.

Part No.

4-233-719-0s

4-233-719-1s

4-233-719-2s

4-233-718-0s

4-233-718-1s

4-233-718-2s

4-233-718-3s

4-233-718-4s

4-233-718-5s

4-233-718-6s

3

CDP-CE275/CE375

• LOCATION OF CONTROLS

– Front panel –

2

1

SECTION 2

GENERAL

3

4

5

6 7

8

9 ws wa w; ql qk

1

POWER button

2 DISC1 – DISC5 button

3 Fluorescent indicator tube display

4 H button

5 X button

6 x button

7

EX-CHANGE button

8 DISC SKIP button

9 l AMS L control

0 A OPEN/CLOSE button qa PHONES jack qj qh qg qf qd qs qa

0 qs

CLEAR button qd CHECK button qf EDIT button qg M button qh m button qj Disc table qk

TIME button ql REPEAT button w; FADER button wa

PEAK SEARCH button ws PLAY MODE button

– Rear panel –

1

2

1 DIGITAL OUT OPTICAL connector

2 ANALOG OUT

4

SECTION 3

DISASSEMBLY

• The equipment can be removed using the following procedure.

Set Case Front Panel Assy CD Mechanism Block

Base Unit (BU-5BD27)

Tray, Table Assy

Optical Pick-up

Sensor Board

Jnuction Board, Loading Motor Board

Note:

Follow the disassembly procedure in the numerical order given.

3-1. CASE

CDP-CE275/CE375

2 two screws

(case 3TP2)

3 two screws

(BVTP 3x8)

4 case

7 panel, loading

1 two screws

(case 3TP2)

5

6

5

CDP-CE275/CE375

3-2. FRONT PANEL ASSY

7

claw

1

CN601

2

CN602

8

front panel assy

3-3. CD MECHANISM BLOCK (CDM59-5BD27)

4

two screws

(BVTP 3x8)

6

claw

4

CN351

3

CN301

5

three screws

(BVTP 3x8)

6

two screws

(BVTP 3x8)

7

CDM59-5BD27

3

three screws

(BVTP 3x8)

5

tray

2

CN311

1

CN302

6

CDP-CE275/CE375

3-4. BASE UNIT (BU-5BD27)

6

spring (932), compression

3

two screws

(+PTPWHM 2.6), floating

2

two screws

(+PTPWHM 2.6), floating

7

base unit (BU-5BD27)

5

spring (932), compression

4

holder (BU) assy

1

two screws

(+PTPWHM 2.6), floating

3-5. TRAY, TABLE ASSY

5

1

two screws

(M 2.6), +BTTP

8

screw

(+PTPWHM 2.6), floating

9

tray

7

table assy

2

bracket (guide)

6

CN15

3

three screws

(M 2.6), +BTTP

4

bracket (guide)

7

CDP-CE275/CE375

3-6. SENSOR BOARD

1

belt (rotary) table assy

4

SENSOR board

3

two screws

(M 2.6), +BTTP

2

two screws

(M 2.6), +BTTP

3-7. JUNCTION BOARD, LOADING MOTOR BOARD

6

two screws

(M 2.6), +BTTP

4

JUNCTION board

7

LOADING MOTOR board

5

belt (loading)

2

CN13

1

CN14

3

three screws

(M 2.6), +BTTP

8

3-8. OPTICAL PICK-UP

3

optical pick-up

4

connector

CDP-CE275/CE375

2

shaft, sled

1

9

CDP-CE275/CE375

Ver 1.1 2001.07

SECTION 4

TEST MODE

Connecting Location:

ADJ MODE

NOTE:

This mode cannot be performed without a general remote commander.

1. Chuck the CD first, and then turn OFF the power.

2. Short-circuit the test point TP1 (ADJ) of the MAIN board and ground with a lead wire.

3. Press the

[POWER]

button to turn ON the power.

The CD is playback automatically and the ADJ mode is set.

4. To exit the mode, press the

[POWER]

button to turn OFF the power.

– MAIN BOARD (Component Side) –

• Prohibits high speed search during accessing

• Ignores even if GFS becomes “L”

ADJ Mode Special Function Table

EDIT

Button

PLAY MODE

Function

Auto gain display

(Focus, Tracking and Sledding)

RFCK

GFS

Error rate display

FLUORESCENT INDICATOR TUBE ALL LIT, AND

KEY CHECK MODE

1. Short-circuit the test TP2 (AFADJ) of the MAIN board and ground with a lead wire.

2. Press the

[POWER]

button to turn ON the power.

The whole fluorescent indicator tube lights up.

3. All buttons have individual button numbers.

When a button is pressed, the button number is counted up and displayed.

JW66

TP1 (ADJ)

CN301

1 0

Count up display Displays button number

When remote controller signals are received, “RM **” will be displayed.

(

** are the numbers corresponding to the remote controller buttons.)

When using the remote controller, switch the

[CD1/2/3]

switch to CD1.

4. To exit the mode, press the

[POWER]

button to turn OFF the power.

JW68

TP2 (AFADJ)

10

CDP-CE275/CE375

Ver 1.1 2001.07

Button

DISC1

DISC2

DISC3

DISC4

DISC5

PLAY MODE

PEAK SEARCH

FADER

REPEAT

TIME

H (PLAY)

X (PAUSE) x (STOP)

EX-CHANGE

DISC SKIP m

M

EDIT

CHECK

CLEAR

AMS (push)

Buttons and Corresponding Button Numbers

AMS (turn)

Button Number or Display

8

20

19

18

12

11

10

9

17

16

Partial lighting 1

Partial lighting 2

All lit

35

26

27

28

36

24

25

37

When rotated clockwise: The music calendar numerals light up in ascending order.

When rotated counterclockwise: The music calendar numerals light up in descending order.

All lit

REPEAT 1

EDIT

TIME

FADE

A B

ALL1DISCS

PROGRAM

SHUFFLE

DISC TRACK PEAK MIN STEP SEC

1 2 3 4 5

6 7 8 9 10

11 12 13 14 15

16 17 18 19 20

Partial lighting 1

Partial lighting 2

TRACK MIN SEC

R r

Light altemately

ALL1DISCS

DISC PEAK STEP

1 2 3 4 5

6 7 8

1

11

3

7

13

18

9

5

15

20

R r

Light altemately

2

6

12

16 17

8

4

14

19

10

11

CDP-CE275/CE375

Ver 1.1 2001.07

AGING MODE

For the aging mode, three modes of all mode, disc table mode, and loading mode are available.

This set has the Aging mode for operation check of the mechanism deck.

• If a failure occurred

The aging operation stops and a faulty status is displayed on the fluorescent indicator tube.

• If no failure occurs

The aging operation continues repeatedly.

Note:

Do not use the test disc when performing aging.

Aging will not be performed properly if discs with tracks shorter than 4 seconds are used.

3

4

5

0

1

2

8

9

6

7

Procedure:

1. Press the

[POWER]

button and turn ON the power.

2. Set discs on all trays.

(More than two discs if five are not available)

3. All mode:

Press the

[CHECK]

,

[PLAY MODE]

and x buttons at the same time.

Disc table mode:

Press the

[CHECK]

,

[PLAY MODE]

and

[SKIP]

buttons at the same time.

Loading mode:

Press the

[CHECK]

,

[PLAY MODE]

and

[EX-CHANGE]

buttons at the same time.

4. Aging starts, and the fluorescent indicator tube will display the following.

5. To exit the mode, press the

[POWER]

button to turn OFF the power.

Code No.

Status All mode

Disc table mode a

Loading mode a a

A

CLOSE (Tray closed)

TOC reading

Access to last track

Play of last track (3 sec)

EX OPEN (Tray opened while chucking)

EX SKIP (Disc tray rotated)

EX CLOSE (Tray closed)

Access to first track

Play of first track (3 sec)

OPEN (tray opened)

DISC SKIP (Disc tray rotated, and next disc was selected) a a a a a a a a a a a a a a a

Display in

Normal operation

A-0

A-1

A-2

Counter display

A-4

A-5

A-6

A-7

Counter display

A-9

A-A

The discs are selectie in the order of DISC1

DISC2

DISC3

DISC4

DISC5

DISC1

.... Empty trays are skipped.

But the order is random in the disc table mode.

Display in case of failure

Err 0

Err 1

Err 2

Err 3

Err 4

Err 5

Err 6

Err 7

Err 8

Err 9

Err A

MECHANISM DECK CHECK MODE

For the mechanism deck check mode, two modes of disc table mode and loading mode are available.

In the mechanism deck check mode, the disc table turning time and the loading time in each section are measured and displayed.

Procedure:

Disc table mode:

Press the

[POWER]

switch while pressing H ,

[ OPEN/CLOSE]

and

[REPEAT]

buttons simultaneously.

Loading mode:

Press the

[POWER]

switch while pressing H ,

[ OPEN/CLOSE]

and

[TIME]

buttons simultaneously.

Display contents

Mode

Disc table mode

(

Table turning

time measurement

)

Table mode

(

Loading time

measurement

)

Check command

0: Right one turn

1: Left one Turn

2: Measurement end

3: Undefined

4: Star position

5: Open

Close

6: Close

BU up

7: BU up

EX open

8: EX open

EX close

9: EX close

BU down

A: BU down

Open

FF: Measurement end

Display r 12.5

L 10.2

r 12.5

Sta – –.–

CLo 10.2

UP 0.7

EoP 6.2

ECL 10.3

don 1.2

oPn 9.3

CLo 10.2

12

SECTION 5

ELECTRICAL ADJUSTMENTS

Note:

1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given.

2. Use PATD-012 disc (4-225-203-01) unless otherwise indicated.

3. Use an oscilloscope with more than 10M

impedance.

4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks.

S Curve Check

Connection:

oscilloscope

BD board

TP (FE1)

TP (VC)

+

CDP-CE275/CE375

Ver 1.1 2001.07

Procedure:

1.

Set the test disc (PATD-012). Disc chucking operation is complete, then press the

[POWER]

button to turn the power off.

2.

Connect an oscilloscope to test point TP (RFDC) and TP (VC) on the BD board.

3.

Connect between test point TP (ADJ) on the MAIN board and

GND by lead wire.

4.

Press the

[POWER]

button to turn the power on and enter the

ADJ mode, then playback the number two track automatically.

5.

Confirm that oscilloscope waveform is clear and check the level of between RFDC top and VC is correct or not.

Note:

A clear RFDC signal waveform means that the shape “

” can be clearly distinguished at the center of the waveform.

RFDC signal waveform

VOLT/DIV: 200 mV

TIME/DIV: 500 ns

Procedure:

1.

Set the test disc (PATD-012). Disc chucking operation is complete, then press the

[POWER]

button to turn the power off.

2.

Connect an oscilloscope to test point TP (FE1) and TP (VC) on the BD board.

3.

Connect between test point TP (ADJ) on the MAIN board and

GND by lead wire.

4.

Press the

[POWER]

button to turn the power on and enter the

ADJ mode.

Then playback the number two track automatically, press the x button to stop the playback.

5.

Press the

[CHECK]

button actuate the focus search. (actuate the focus search when disc table is moving in and out)

6.

Check the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 2 ± 1

Vp-p.

S-curve waveform symmetry

Checking Location: BD board

RFAC Level Check

Connection:

BD board

TP (RFAC)

TP (VC)

+

– level: 1.15

±

0.35 Vp-p

VC oscilloscope

A

B within 2

±

1 Vp-p

Note:

• Try to measure several times to make sure than the ratio of A : B or B : A is more than 10 : 7.

• Take sweep time as long as possible and light up the brightness to obtain best waveform.

Checking Location: BD board

RFDC Level Check

Connection:

oscilloscope

BD board

TP (RFDC)

TP (VC)

+

Procedure:

1.

Set the test disc (PATD-012). Disc chucking operation is complete, then press the

[POWER]

button to turn the power off.

2.

Connect an oscilloscope to test point TP (RFAC) and TP (VC) on the BD board.

3.

Connect between test point TP (ADJ) on the MAIN board and

GND by lead wire.

4.

Press the

[POWER]

button to turn the power on and enter the

ADJ mode, then playback the number two track automatically.

5.

Confirm that oscilloscope waveform is clear and check RFAC signal level is correct or not.

Note:

A clear RFAC signal waveform means that the shape “

” can be clearly distinguished at the center of the waveform.

RFAC signal waveform

VOLT/DIV: 200 mV

TIME/DIV: 500 ns level: 1.35

±

0.4 Vp-p

Checking Location: BD board

13

CDP-CE275/CE375

Ver 1.1 2001.07

E-F Balance Check

Connection:

oscilloscope

BD board

TP (TE1)

TP (VC)

+

Procedure:

1.

Set the test disc (PATD-012). Disc chucking operation is complete, then press the

[POWER]

button to turn the power off.

2.

Connect an oscilloscpe to test point TP (TE1) and TP (VC) on the BD board.

3.

Connect between test point TP (ADJ) on the MAIN board and

GND by lead wire.

4.

Press the

[POWER]

button to turn the power on and enter the

ADJ mode, then playback the number two track automatically.

5.

Press the

[TIME]

button. (The tracking servo and the sledding servo are turned OFF)

6.

Check the level B of the oscilliscope waveform and the A (DC voltage) of the center of the Traverse waveform.

Confirm the following :

A/B x 100 = less than ± 22%

Traverse Waveform

Center of the waveform

B

0V

A (DC voltage) level: 1.15

±

0.5 Vp-p

7.

Press the

[TIME]

button. (The tracking servo and sledding servo are turned ON)

Confirm the C (DC voltage) is almost equal to the A (DC voltage) is step 6.

Traverse Waveform

Checking Location:

– BD BOARD (Conductor Side) –

TP

(VC)

IC150

IC131

TP

(TE1)

TP

(FE1)

TP

(RFDC)

IC101

TP

(RFAC)

0V

Tracking servo

Sled servo

OFF

Checking Location: BD board

Tracking servo

Sled servo

ON

C (DC voltage)

14

SECTION 6

DIAGRAMS

6-1.

NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

Note on Printed Wiring Board:

X

: parts extracted from the component side.

Y

: parts extracted from the conductor side.

• : Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)

Caution:

Pattern face side: Parts on the pattern face side seen from

(Conductor Side) the pattern face are indicated.

Parts face side: Parts on the parts face side seen from

(Component Side) the parts face are indicated.

• Indication of transistor

Q

B C E

Q

B C E

These are omitted.

These are omitted.

Note on Schematic Diagram:

• All capacitors are in µF unless otherwise noted. pF: µµF

50 WV or less are not indicated except for electrolytics and tantalums.

• All resistors are in

and 1 /

4

W or less unless otherwise specified.

• f

: internal component.

C

: panel designation.

Note:

The components identified by mark

0

or dotted line with mark

0

are critical for safety.

Replace only with part number specified.

Note:

Les composants identifiés par une marque

0

sont critiques pour la sécurité.

Ne les remplacer que par une pièce por tant le numéro spécifié.

• Voltages and waveforms are dc with respect to ground under no-signal conditions.

no mark : CD PLAY

• Voltages are taken with a VOM (Input impedance 10 M

).

Voltage variations may be noted due to normal production tolerances.

• Waveforms are taken with a oscilloscope.

Voltage variations may be noted due to normal production tolerances.

• Circled numbers refer to waveforms .

• Signal path.

J

: CD PLAY c

: DIGITAL OUT

• A : B+ Line

B

: B– Line

CDP-CE275/CE375

• Circuit Boards Location

LOADING MOTOR board

POWER SW board

SENSOR board

BD board

JUNCTION board

KEY board

DISPLAY board

HEADPHONE board

MAIN board

15 15

CDP-CE275/CE375

Ver 1.1 2001.07

6-2.

PRINTED WIRING BOARD – BD Board – •

See page 15 for Circuit Boards Location.

• Semiconductor

Location

Ref. No.

Location

Q131

Q132

C-3

C-3

TP

(VC)

16 16

TP

(FE1)

TP

(TE1)

TP (RFDC)

TP (RFAC)

• Semiconductor

Location

Ref. No.

Location

IC101

IC131

IC150

C-2

C-1

B-1

(Page 20)

CDP-CE275/CE375

Ver 1.1 2001.07

6-3.

SCHEMATIC DIAGRAM – BD Board – •

See page 24 for Waveforms.

See page 24 for IC Block Diagrams.

TP

(RFAC)

TP

(RFDC)

TP

(VC)

TP

(TE1)

TP

(FE1)

TP

(SE1)

IC BD

IC BD

(Page 21)

17 17

The components identified by mark

0

or dotted line with mark 0 are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque

0

sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

CDP-CE275/CE375

6-4.

PRINTED WIRING BOARDS – JUNCTION/SENSOR/LOADING MOTOR Boards – •

See page 15 for Circuit Boards Location.

(Page 20)

TO MAIN

BOARD

• Semiconductor

Location

Ref. No.

Location

IC11 C-2

• Semiconductor

Location

Ref. No.

Location

D10

D11

B-4

E-3

18 18

6-5.

SCHEMATIC DIAGRAM – JUNCTION/SENSOR/LOADING MOTOR Boards – •

See page 25 for IC Block Diagram.

TO MAIN BOARD

(Page 21)

CDP-CE275/CE375

IC BD

19 19

CDP-CE275/CE375

Ver 1.1 2001.07

6-6.

PRINTED WIRING BOARD – MAIN Board – •

See page 15 for Circuit Boards Location.

(Page 22)

(Page 22)

TP1 (ADJ)

TP2 (AFDJ)

(Page 18)

(Page 18)

20 20

(Page 22)

• Semiconductor Location

Ref. No.

Location

D353

D601

D602

D603

D604

D605

D606

D607

D608

D609

D610

D-10

C-7

B-7

C-7

B-7

B-6

A-6

C-7

C-8

C-7

A-6

IC301

IC303

IC350

C-3

D-11

E-10

Ref. No.

Location

IC351

IC601

IC602

IC603

E-2

A-5

B-5

A-4

Q301

Q307

Q352

Q353

Q356

Q402

Q405

Q502

Q505

Q601

C-2

D-5

E-7

E-8

D-11

D-11

D-11

E-11

E-11

A-6

CDP-CE275/CE375

6-7.

SCHEMATIC DIAGRAM – MAIN Board – •

See page 24 for Waveform.

(Page 23)

(Page 17)

(Page 19)

21 21

(Page 23)

(Page 23)

The components identified by mark

0

or dotted line with mark

0

are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque

0

sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

CDP-CE275/CE375

6-8.

PRINTED WIRING BOARDS – PANEL Section – •

See page 15 for Circuit Boards Location.

(Page 20)

(Page 20)

22 22

• Semiconductor

Location

Ref. No.

Location

IC802 A-13

(Page 20)

6-9.

SCHEMATIC DIAGRAM – PANEL Section –

(Page 21)

(Page 21)

The components identified by mark

0

or dotted line with mark

0

are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque

0

sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

23 23

CDP-CE275/CE375

(Page 21)

CDP-CE275/CE375

• Waveforms

– BD Board –

1 IC101 yj

(XTAO)

5 IC101 el

(FE) (CD Play Mode)

– MAIN Board –

1 IC301 es

(XTAL)

3.1 Vp-p

16.9344 MHz

2 IC101 ta

(RF AC) (CD Play Mode) 6 IC101 wh

(MDP) (CD Play Mode)

1.2 Vp-p

0.5 Vp-p

2.5 Vp-p

10 MHz

3 IC101 rd

(RF DC)

1.3 Vp-p

7.8

µ

s

• IC Block Diagrams

– BD BOARD –

IC101 CXD2587Q

4.2 Vp-p

60

DIGITAL

OUT

LRCK

61

PCMD

62

BCK

63

EMPH 64

XVDD 65

XTAI

XTAO

XVSS

AVDD1

AOUT1

AIN1

66

67

68

69

70

71

D/A

INTERFACE

TIMING

LOGIC

LOUT1 72

AVSS1

AVSS2

73

74

LOUT2 75

AIN2

AOUT2

AVDD2

RMUT

LMUT

76

77

78

79

80

PWM PWM

3rd ORDER

NOISE SHAPER

OVER SAMPLING

DIGITAL FILTER

SERIAL IN

INTERFACE

59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41

ERROR

CORRECTOR

16K

RAM

DIGITAL

PLL

EFM

DEMODULATOR

ASYMMETRY

CORRECTION

OPERATIONAL

AMPLIFIER

ANALOG SWITCH

A/D

CONVERTER

SUBCODE

PROCESSOR

SERVO

INTERFACE

SERVO AUTO

SEQUENCER

SERVO DSP

FOCUS

SERVO

TRACKING

SERVO

SLED

SERVO

40

39

38

SE

FE

VC

CLOCK

GENERATOR

PWM GENERATOR

FOCUS PWM

GENERATOR

TRACKING

PWM GENERATOR

SLED PWM

GENERATOR

DIGITAL

CLV

MIRR, DFCT,

FOK

DETECTOR

37

36

35

34

XTSL

TES1

TEST

VSS

33

32

31

30

29

28

FRDR

FFDR

TRDR

TFDR

SRDR

SFDR

27

SSTP

26

25

MDP

LOCK

24

23

22

FOK

DFCT

MIRR

1

2

3 4

CPU

INTERFACE

5 6

7

8

9 10 11 12 13 14 15 16 17 18 19 20

21 COUT

4 IC101 ra

(TE) (CD Play Mode)

0.2 Vp-p

24 24

CDP-CE275/CE375

– BD Board –

IC131 CXA2581N

LD

PD

EQ IN

3

AC SUM 4

AC

SUM

GND

A

B

C

D

F

1

2

5

6

7

8

9

10

E

11

SW 12

DVCC

13 gm gm

APC

APC-OFF(Hi-Z)

RW/ROM

(H/L)

DVC

RW/ROM

VOFST

VC

RW/ROM

VOFST

A

D

B

C

VC

12 DC_OFST

RW/ROM

DVCC

11

RFDCI

11 RFDCO

VCC

DVC

VC

VC

VC

RW/ROM

EQ

EQ

ON/OFF

VCC

AC

VCA

VCC

10 VC

26 RFC

25 VFC

24 BST

23 RFG

22 VCC

21

20

CEI

CE

19 TE_BAL

DVCC RW/ROM

18 TE

RW/ROM

AVC

DVC

VC

DVC

VOFST

DVC

DVCC

17 FEI

16 FE

DVC

14

RFAC

15

– JUNCTION Board –

IC11 BA6780

VIN1

1 18

VIN2

FIN1

2

RIN1

3

IOUT 4

17

FIN2

16

RIN2

15

CT2

VREF

5

VOLTAGE OUTPUT

VREG

6

VCC 7

14 VEE

13

FBIN-

12

FBIN+

OUT1+

8

OUT1 9

11

OUT2+

10

OUT2-

25

CDP-CE275/CE375

26

27

28

23

24

25

20

21

22

16

17

18

19

33

34

35

29

30

31

32

36

13

14

15

10

11

12

5

8

9

6

7

37

Pin No.

Pin Name I/O

1

2

3

SQSO

SQCK

XRST

O

I

I

4 SYSM I

XUGF

XPCK

GFS

C2PO

SCOR

COUT

MIRR

DFCT

FOK

LOCK

MDP

SSTP

SFDR

SRDR

TFDR

TRDR

FFDR

FRDR

VSS

TEST

TES1

DATA

XLAT

CLOK

SENS

SCLK

VDD

ATSK

SPOA

SPOB

XLON

WFCK

XTSL

O

I

O

I/O

I/O

I/O

O

I/O

I/O

O

O

O

O

O

I

O

O

O

O

I

I

O

O

I/O

I

I

O

I

I

I

I

6-10.

IC PIN FUNCTION DESCRIPTION

• BD BOARD IC101 CXD2587Q

(DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, DIGITAL FILTER, D/A CONVERTER)

38

39

40

41

42

VC

FE

SE

TE

CE

I

I

I

I

I

Description

Subcode Q data output to the system controller (IC301)

Subcode Q data reading clock signal input from the system controller (IC301)

System reset signal input from the system controller (IC301) “L”: reset

Analog line muting on/off control signal input terminal “H”: line muting on

Not used (fixed at “L”)

Command serial data input from the system controller (IC301)

Command latch pulse input from the system controller (IC301)

Command serial data transfer clock signal input from the system controller (IC301)

Internal status monitor output to the system controller (IC301)

SENSE serial data reading clock input from the system controller (IC301)

Power supply terminal (+5V) (digital system)

Input pin for anti-shock Not used (fixed at “L”)

Microcomputer escape interface input A terminal Not used (fixed at “L”)

Microcomputer escape interface input B terminal Not used (fixed at “L”)

Microcomputer escape interface output to the CXA2568M (IC103)

WFCK output terminal Not used (open)

Not used (open)

Not used (open)

Not used (open)

Not used (open)

Subcode sync (S0+S1) detection signal output to the system controller (IC301)

Numbers of track counted signal input/output terminal Not used (open)

Mirror signal input/output terminal Not used (open)

Defect signal input/output terminal Not used (open)

Focus OK input/output terminal Not used (open)

GFS is sampled by 460 Hz “H” when GFS is “H” Not used (open)

Spindle motor (M101) servo drive signal output to the BA5974FP (IC102)

Limit in detect switch (S101) input terminal

Sled servo drive PWM signal (+) output to the BA5974FP (IC102)

Sled servo drive PWM signal (–) output to the BA5974FP (IC102)

Tracking servo drive PWM signal (+) output to the BA5974FP (IC102)

Tracking servo drive PWM signal (–) output to the BA5974FP (IC102)

Focus servo drive PWM signal (+) output to the BA5974FP (IC102)

Focus servo drive PWM signal (–) output to the BA5974FP (IC102)

Ground terminal (digital system)

Input terminal for the test (fixed at “L”)

Input terminal for the test (fixed at “L”)

Input terminal for the system clock frequency setting “L”: 45.1584 MHz, “H”: 22.5792 MHz

(fixed at “L” in this set)

Middle point voltage (+2.5V) input from the CXA2568M (IC103)

Focus error signal input from the CXA2568M (IC103)

Sled error signal input from the CXA2568M (IC103)

Tracking error signal input from the CXA2568M (IC103)

Command chip enable signal input from the CXA2568M (IC103)

26

CDP-CE275/CE375

76

77

78

72

73

74

75

79

80

69

70

71

66

67

68

62

63

64

65

59

60

61

55

56

57

58

52

53

54

Pin No.

Pin Name I/O

43

44

RFDC

ADIO

I

O

48

49

50

51

45

46

47

AVSS0

IGEN

AVDD0

ASYO

ASYI

BIAS

RFAC I

I

O

I

I

AVSS3

CLTV

FILO

FILI

PCO

AVDD3

VSS

VDD

DOUT

LRCK

PCMD

BCK

EMPH

XVDD

O

O

O

O

O

I

O

I

O

XTAI

XTAO

XVSS

AVDD1

AOUT1

AIN1

LOUT1

AVSS1

AVSS2

LOUT2

AIN2

AOUT2

AVDD2

RMUT

LMUT

I

O

O

O

O

O

O

I

I

O

Description

RF signal input from the CXA2568M (IC103)

Monitor output of the A/D converter input signal Not used (open)

Ground terminal (digital system)

Stabilized current input for operational amplifiers

Power supply terminal (+5V) (digital system)

Playback EFM full-swing output terminal

Playback EFM asymmetry comparator voltage input terminal

Playback EFM asymmetry circuit constant current input terminal

EFM signal input from the CXA2568M (IC103)

Ground terminal (digital system)

Internal VCO control voltage input of the playback master PLL

Filter output for master clock of the playback master PLL

Filter input for master clock of the playback master PLL

Phase comparison output for master clock of the playback EFM master PLL

Power supply terminal (+5V) (digital system)

Ground terminal (digital system)

Power supply terminal (+5V) (digital system)

Digital audio signal output to the DIGITAL OUT OPTICAL (IC303)

L/R sampling clock signal (44.1 kHz) output terminal Not used (open)

D/A interface serial data output terminal Not used (open)

Bit clock signal (2.8224 MHz) output terminal Not used (open)

De-emphasis control signal output terminal Not used (open)

Power supply terminal (+5V) (crystal oscillator system)

System clock input terminal (16.9344 MHz)

System clock output terminal (16.9344 MHz)

Ground terminal (crystal oscillator system)

Power supply terminal (+5V) (analog system)

L-ch analog audio signal output terminal

L-ch operational amplifiers input terminal

L-ch line output terminal

Ground terminal (analog system)

Ground terminal (analog system)

R-ch line output terminal

R-ch operational amplifiers input terminal

R-ch analog audio signal output terminal

Power supply terminal (+5V) (analog system)

R-ch line muting on/off control signal output terminal

L-ch line muting on/off control signal output terminal

27

CDP-CE275/CE375

• MAIN BOARD IC301 CXP82532-013Q

(SYSTEM CONTROLLER, FLUORESCENT INDICATOR TUBE DRIVER, KEY CONTROL)

21

22

23

18

19

20

15

16

17

11

12

13

14

24

25

26

27

28

29

Pin No.

Pin Name I/O

1

2

3

BUSIN

RMIN

NC

I

I

I

8

9

10

6

7

4

5

XLT

LDON

TSENS

DA CS

O

O

I/O

I/O

CLK I/O

LDON/RW I/O

DATA I/O

SQCK

SUBQ

NC

OUT SW

S1

S2

NC

TBLL

TBLR

LD IN

LD OUT

NC

NC

TEST

KEY3

KEY4

KEY5

KEY6

NC

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

I/O

O

I/O

I/O

I/O

I/O

30

31

32

33

34

35

36

37

RST

EXTAL

XTAL

VSS

NC

NC

NC

NC

I/O

I

O

O

O

O

O

Description

Sircs remote control signal input terminal Not used (pull up)

Remote control signal input from the remote control receiver (IC802)

Not used (open)

Serial data latch pulse signal output to the CXD2587Q (IC101)

Laser diode ON/OFF output

Detect signal input from the table sensor (D10)

DA CS

Serial data transfer clock signal output to the CXD2587Q (IC101)

Laser diode ON/OFF output

Serial data output to the CXD2587Q (IC101)

Sub-code Q data reading clock signal output to the CXD2587Q (IC101)

Sub-code Q data signal input from the CXD2587Q (IC101)

Not used (open)

Detect signal input from the open/close detect switch (S11)

Detect signal input from the tray address detect switch (S200)

Detect signal input from the tray address detect switch (S200)

Not used (open)

Table motor drive signal (counterclockwise) output to the BA6780 (IC11)

Table motor drive signal (clockwise) output to the BA6780 (IC11)

Loading motor (M11) drive signal output to the BA6780 (IC11) *1

Loading motor (M11) drive signal output to the BA6780 (IC11) *1

Not used (open)

Not used (open)

Key input terminal (A/D input)

Key input terminal (A/D input) (S812 to S816)

Key input terminal (A/D input) (S817 to S821)

Key input terminal (A/D input) (S806 to S810)

Key input terminal (A/D input) (S801 to S805)

Not used (open)

System reset signal input from the reset signal generator (IC601) “L” reset

For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”

Main system clock input terminal (10 MHz)

Main system clock output terminal (10 MHz)

Ground terminal

Not used (open)

Not used (open)

Not used (open)

Not used (open)

*1 Loading motor (M11) control

Operation

Terminal

LOAD IN (pin @º)

LOAD OUT (pin @¡)

OFF

“L”

“L”

OFF

“L”

“H”

IN BRAKE

“H”

“L”

“H”

“H”

28

CDP-CE275/CE375

Pin No.

Pin Name I/O

38 to 57 P1 to P20 O

58 to 62 NC

63 to 70 G1 to G8

71 VG

O

O

72

73 to 75

76

77

78

79

80

VDD

NC

AFADJ

BUSOUT

DSENS

SENS

SCOR

I

I

I

O

I

O

Description

Segment drive signal output to the fluorescent indicator tube (FL801)

Not used (open)

Grid drive signal output to the fluorescent indicator tube (FL801)

Power supply terminal (–30V) (for fluorescent indicator tube drive)

Power supply terminal (+5V)

Not used (open)

Setting terminal for the test mode “L” active

Sircs remote control signal output terminal Not used (open)

Detect signal input from the disc sensor (D11)

Internal status (SENSE) signal input from the CXD2587Q (IC101)

Sub-code sync (S0+S1) detection signal input from the CXD2587Q (IC101)

29

CDP-CE275/CE375

NOTE:

• -XX and -X mean standardized parts, so they may have some difference from the original one.

• Color Indication of Appearance Parts

Example:

KNOB, BALANCE (WHITE) . . . (RED)

↑ ↑

Parts Color Cabinet's Color

• Abbreviation

AUS : Australian model

CND : Canadian model

EA : Saudi Arabia model

SP : Singapore model

6

7-1. CASE SECTION

SECTION 7

EXPLODED VIEWS

• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

• The mechanical parts with no reference number in the exploded views are not supplied.

• Accessories and packing materials are given in the last of the electrical parts list.

#1

The components identified by mark 0 or dotted line with mark

0 are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiquens pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

7

#1

#1

CDM59-5BD27

FRONT PANEL SECTION

10

6

8

#1

#1

9

#1

11

#1 #2

4

not supplied

2

1

not supplied

3

#1

5

#1

Ref. No.

1

1

1

1

2

Part No.

Description

A-4725-570-A MAIN MOUNTED PC BOARD (CE275)

A-4725-571-A MAIN MOUNTED PC BOARD (CE375:US/CND)

A-4725-579-A MAIN MOUNTED PC BOARD

(CE375:AUS/AEP/UK/SP)

A-4725-581-A MAIN MOUNTED PC BOARD (CE375:E)

4-943-687-01 HOLDER, PC BOARD

Remark Ref. No.

Part No.

0 9

0 9

0 9

0 9

0 9

Description

1-575-651-21 CORD,POWER (CE375:AEP/UK/SP)

Remark

1-696-845-11 CORD,POWER (CE275:AUS,CE375:AUS)

1-777-071-41 CORD,POWER (CE375:AEP/UK/SP)

1-783-528-21 CORD,POWER (TRACKING)(CE375:E)

1-783-531-31 CORD,POWER (CE275:US/CND,CE375US/CND)

3

4

5

5

6

6

7

X-4953-448-1 FOOT ASSY

4-232-237-01 FOOT(DIA. 30)

4-231-683-01 PANEL, LOADING(BLACK)

(CE275,CE375:US/CND/AUS/AEP/UK/SP/E)

4-231-683-21 PANEL, LOADING(SILVER)(CE375:AEP)

4-210-291-01 SCREW(CASE 3 TP2)(BLACK)

(CE275,CE375:US/CND/AUS/AEP/UK/SP/E)

10

10

10

10

10

10

10

10

10

10

4-233-718-01 PANEL, BACK (CE375:US)

4-233-718-11 PANEL, BACK (CE375:CND)

4-233-718-21 PANEL, BACK (CE375:AEP)

4-233-718-31 PANEL, BACK (CE375:UK)

4-233-718-41 PANEL, BACK (CE375:AUS)

4-233-718-51 PANEL, BACK (CE375:E)

4-233-718-61 PANEL, BACK (CE375:SP)

4-233-719-01 PANEL, BACK (CE275:US)

4-233-719-11 PANEL, BACK (CE275:CND)

4-233-719-21 PANEL, BACK (CE275:AUS)

7

8

* 8

4-210-291-11 SCREW(CASE 3 TP2)(SILVER)(CE375:AEP)

4-231-686-11 CASE(409538)(BLACK)

(CE275,CE375:US/CND/AUS/AEP/UK/SP/E)

4-231-686-31 CASE(409538)(SILVER)(CE375:AEP)

3-703-571-11 BUSHING (S)(4516), CORD (CE375:E)

3-703-244-00 BUSHING (2104), CORD

(CE275,CE375:US/CND/AUS/AEP/UK/SP)

11

0 T601

0 T601

0 T601

3-703-249-01 SCREW, S TIGHT, +PTTWH 3X6

1-435-342-11 TRANSFORMER, POWER

(CE275:US/CND,CE375:US/CND)

1-435-343-11 TRANSFORMER, POWER

(CE275:AUS,CE375:AUS/AEP/UK/SP)

1-435-344-11 TRANSFORMER, POWER (CE375:E)

30

CDP-CE275/CE375

7-2. FRONT PANEL SECTION

54

55

57

56

62

58

57

57

53

FL801

52

60

59

61

57

not supplied supplied with J881

51

Ref. No.

Part No.

51

51

51

51

51

Description

A-4953-509-1 PANEL ASSY, FRONT (CE375:US/CND)

Remark

X-4953-510-1 PANEL ASSY, FRONT(SILVER)(CE375:AEP)

X-4953-511-1 PANEL ASSY, FRONT(BLACK)(CE275:US/CND)

X-4953-519-1 PANEL ASSY, FRONT(BLACK)

(CE375:AUS/AEP/UK/SP/E)

X-4953-520-1 PANEL ASSY, FRONT(BLACK)(CE275:AUS)

Ref. No.

Part No.

54

55

56

57

58

Description

4-231-973-11 BUTTON (POWER)(CE375:AEP)

1-681-141-21 POWER SW BOARD

1-681-140-21 KEY BOARD

4-951-620-01 SCREW (2.6X8), +BVTP

4-231-690-01 HOLDER (FL A)

52

53

53

54

3-354-981-11 SPRING (SUS), RING

4-231-928-01 KNOB(AMS)(BLACK)

(CE275,CE375:US/CND/AUS/AEP/UK/SP/E)

4-231-928-11 KNOB(AMS)(SILVER)(CE375:AEP)

4-231-973-01 BUTTON (POWER)(BLACK)

(CE275,CE375:US/CND/AUS/AEP/UK/SP/E)

Remark

59

60

61

62

1-681-139-11 DISPLAY BOARD

1-792-486-11 WIRE(FLAT TYPE)(37 CORE)

1-681-142-21 HEADPHONE BOARD

4-374-846-31 COVER, CAPACITOR, CAP TYPE

(CE275:AUS,CE375:AUS/AEP/UK/SP/E)

FL801 1-517-946-21 INDICATOR TUBE, FLUORESCENT

31

CDP-CE275/CE375

7-3. CD MECHANISM SECTION (1)

(CDM59-5BD27)

106

110

106

107

109

108

105

106

104

102

not supplied

101

103

103

not supplied

M11

113

not supplied

114

112

111

102

115

115

102

BU-5BD27

117

118

A

102

not supplied

106

116

A

117

101

102

Ref. No.

Part No.

101

102

* 103

104

105

Description

4-224-619-01 BRACKET (GUIDE)

4-218-253-31 SCREW (M2.6), +BTTP

4-951-619-01 CUSHION (A)

4-224-602-01 TABLE

4-224-617-01 GEAR (RM-E)

106

107

108

109

110

4-218-252-51 SCREW (+PTPWH M2.6), FLOATING

4-224-616-01 GEAR (RM-M)

4-224-615-03 GEAR (RM-B)

4-225-328-01 BELT (ROTARY)

4-224-603-01 TRAY

Remark Ref. No.

Part No.

111

112

* 113

114

115

Description

1-791-930-11 WIRE (FLAT TYPE)(6 CORE)

1-676-245-11 SENSOR BOARD

X-4924-457-1 ROLLER ASSY

A-4672-867-A MOTOR ASSY, ROTARY

4-985-672-01 SCREW (+PTPWH M2.6), FLOATING

Remark

116

117

118

1-757-648-11 WIRE (FLAT TYPE)(21 CORE)

4-959-996-01 SPRING (932), COMPRESSION

X-4952-312-1 HOLDER (BU) ASSY

32

CDP-CE275/CE375

7-4. CD MECHANISM SECTION (2)

(CDM59-5BD27)

159

163

162

161

156

160

156

164

165

158

153

155

156

169

166

156

168

167

M10 not supplied

157

156

154

156

170

not supplied

152

153

151

Ref. No.

Part No.

151

152

153

154

155

Description

X-4952-019-2 PULLEY (A) ASSY, CHUCKING

1-676-246-11 JUNCTION BOARD

4-218-253-31 SCREW (M2.6), +BTTP

4-225-885-01 BELT (LOADING)

4-225-844-01 GEAR (LOADING A)

156

157

158

159

160

4-218-252-51 SCREW (+PTPWH M2.6), FLOATING

A-4672-879-A MOTOR ASSY, LOADING

1-676-244-11 LOADING MOTOR BOARD

4-224-613-01 GEAR (SHAFT)

1-418-746-11 ENCODER, ROTARY

Remark Ref. No.

Part No.

161

162

163

164

165

Description

4-224-607-01 GEAR, SWING

4-224-609-01 GEAR (LOADING C)

4-224-608-01 COLLAR, SWING

4-224-611-01 GEAR (LOADING B)

3-016-533-01 WASHER (FR), STOPPER

166

167

168

169

170

4-224-606-01 GEAR (RV)

4-224-605-01 GEAR (U/D)

1-471-061-11 MAGNET ASSY

4-221-688-01 PULLEY (B), CHUCKING

4-224-618-01 LEVER (LIFTER)

Remark

33

CDP-CE275/CE375

7-5. BASE UNIT SECTION

(BU-5BD27)

201

210

203

202

205

M101

209

M102

204

204

206

207

208

The components identified by mark 0 or dotted line with mark 0 are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

Ref. No.

Part No.

0 201

202

203

204

205

Description

1-796-033-11 LIGHT PICK UP (PXR-104X)

1-782-817-11 WIRE (FLAT TYPE)(16 CORE)

4-917-567-01 GEAR (M)

4-951-940-01 INSULATOR (BU)

4-917-565-01 SHAFT, SLED

Remark Ref. No.

Part No.

206

207

208

209

210

Description

4-917-564-01 GEAR (P), FLATNESS

A-4725-568-A BDMOUNTED PC BOARD (A)

4-951-620-01 SCREW (2.6X8), +BVTP

4-917-566-01 GEAR (S)

3-713-786-51 SCREW +P 2X3

M101 X-4917-523-3 MOTOR ASSY (SPINDLE)

M102 X-4917-504-1 MOTOR ASSY (SLED)

Remark

34

SECTION 8

ELECTRICAL PARTS LIST

NOTE:

• Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.

• -XX and -X mean standardized parts, so they may have some difference from the original one.

• RESISTORS

• Items marked “*” are not stocked since they are seldom required for routine service.

Some delay should be anticipated when ordering these items.

• SEMICONDUCTORS

In each case, u: µ, for example: uA. .

: µA. .

uPB. . : µPB. .

All resistors are in ohms.

METAL: Metal-film resistor.

METAL OXIDE: Metal oxide-film resistor.

F: nonflammable

• Abbreviation

AUS : Australian model

CND : Canadian model

EA : Saudi Arabia model

SP : Singapore model uPD. . : µPD. .

• CAPACITORS uF: µF

• COILS uH: µH uPA. . : µPA. .

uPC. . : µPC. .

CDP-CE275/CE375

BD

The components identified by mark 0 or dotted line with mark

0 are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiquens pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

When indicating parts by reference number, please include the board.

Ref. No.

Part No.

Description

A-4725-568-A BD BOARD, COMPLETE

*******************

< CAPACITOR >

Remark

C101 1-164-315-11 CERAMIC CHIP 470PF

C102 1-164-156-11 CERAMIC CHIP 0.1UF

C103 1-164-315-11 CERAMIC CHIP 470PF

C110 1-126-206-11 ELECT CHIP 100UF

C111 1-164-156-11 CERAMIC CHIP 0.1UF

5.00% 50V

25V

5.00% 50V

20% 6.3V

25V

C112 1-164-156-11 CERAMIC CHIP 0.1UF

C120 1-164-156-11 CERAMIC CHIP 0.1UF

25V

25V

C121 1-162-970-11 CERAMIC CHIP 0.01UF

10% 25V

C122 1-117-863-11 CERAMIC CHIP 0.47UF

10.00% 6.3V

C123 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C124 1-162-967-11 CERAMIC CHIP 0.0033UF 10% 50V

C125 1-162-965-11 CERAMIC CHIP 0.0015UF 10% 50V

C126 1-107-826-11 CERAMIC CHIP 0.1UF

C130 1-164-505-11 CERAMIC CHIP 2.2UF

C131 1-164-505-11 CERAMIC CHIP 2.2UF

10.00% 16V

16V

16V

C132 1-164-505-11 CERAMIC CHIP 2.2UF

C133 1-126-607-11 ELECT CHIP 47UF

C134 1-126-607-11 ELECT CHIP 47UF

C136 1-107-826-11 CERAMIC CHIP 0.1UF

C137 1-126-209-11 ELECT CHIP 100UF

20%

20%

16V

4V

4V

10.00% 16V

20.00% 4V

C138 1-162-964-11 CERAMIC CHIP 0.001UF

10% 50V

C139 1-162-921-11 CERAMIC CHIP 33PF 5% 50V

C140 1-164-505-11 CERAMIC CHIP 2.2UF

C145 1-162-908-11 CERAMIC CHIP 3PF

C150 1-126-204-11 ELECT CHIP 47UF

16V

0.25PF 50V

20% 16V

C151 1-164-156-11 CERAMIC CHIP 0.1UF

C152 1-162-919-11 CERAMIC CHIP 22PF

C153 1-162-919-11 CERAMIC CHIP 22PF

5%

5%

25V

50V

50V

C154 1-162-964-11 CERAMIC CHIP 0.001UF

10% 50V

C158 1-164-172-11 CERAMIC CHIP 0.0056UF 10.00% 25V

C171 1-126-206-11 ELECT CHIP 100UF

C172 1-164-156-11 CERAMIC CHIP 0.1UF

C173 1-162-928-11 CERAMIC CHIP 120PF

C174 1-115-412-11 CERAMIC CHIP 680PF

C181 1-126-206-11 ELECT CHIP 100UF

C182 1-164-156-11 CERAMIC CHIP 0.1UF

C183 1-162-928-11 CERAMIC CHIP 120PF

C184 1-115-412-11 CERAMIC CHIP 680PF

C191 1-126-205-11 ELECT CHIP 47UF

C192 1-164-156-11 CERAMIC CHIP 0.1UF

20% 6.3V

25V

5% 50V

5.00% 25V

20% 6.3V

5%

25V

50V

5.00% 25V

20% 6.3V

25V

Ref. No.

Part No.

Description

C193 1-162-920-11 CERAMIC CHIP 27PF

C194 1-162-918-11 CERAMIC CHIP 18PF

C199 1-164-156-11 CERAMIC CHIP 0.1UF

Remark

5% 50V

5.00% 50V

25V

< CONNECTOR >

CN101 1-784-360-11 CONNECTOR,FFC(LIF(NON-ZIF))21P

CN102 1-777-937-11 CONNECTOR, FFC/FPC 16P

< FERRITE BEAD >

FB191 1-216-864-91 SHORT 0

< IC >

IC101 8-752-386-85 IC CXD2587Q

IC131 8-752-089-74 IC CXA2581N-T4

IC150 8-759-829-14 IC AN4800SB

< MOTOR >

M101 X-4917-523-3 MOTOR ASSY (SPINDLE)

M102 X-4917-504-1 MOTOR ASSY (SLED)

< TRANSISTOR >

Q131

Q132

8-729-010-08 TRANSISTOR

8-729-600-22 TRANSISTOR

< RESISTOR >

MSB710-R

2SA1235-F

R101 1-216-835-11 METAL CHIP

R102 1-216-845-11 METAL CHIP

R103 1-216-835-11 METAL CHIP

R110 1-216-821-11 METAL CHIP

R111 1-216-809-11 METAL CHIP

R112 1-216-833-11 METAL CHIP

R120 1-216-839-11 METAL CHIP

R121 1-216-833-11 METAL CHIP

R122 1-216-845-11 METAL CHIP

R123 1-216-857-11 METAL CHIP

R125 1-216-827-11 METAL CHIP

R126 1-216-833-11 METAL CHIP

R127 1-216-821-11 METAL CHIP

R129 1-216-815-11 METAL CHIP

R134 1-216-853-11 METAL CHIP

R135 1-216-836-11 METAL CHIP

R136 1-216-836-11 METAL CHIP

R137 1-216-797-11 METAL CHIP

3.3K

10K

1K

330

470K

18K

18K

10

15K

100K

15K

1K

100

10K

33K

10K

100K

1M

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

35

CDP-CE275/CE375

BD DISPLAY HP

Ref. No.

R138 1-216-798-11 RES-CHIP

R139 1-216-847-11 METAL CHIP

R140

R141

R142

R143

R144

R145 1-216-830-11 METAL CHIP

R146 1-216-845-11 METAL CHIP

R149 1-216-821-11 METAL CHIP

R151 1-216-845-11 METAL CHIP

R152

R153

R155

R171

R172

R173

Part No.

Description

1-216-854-11 METAL CHIP

1-216-840-11 METAL CHIP

1-216-841-11 METAL CHIP

1-216-855-11 METAL CHIP

1-216-846-11 METAL CHIP

1-216-833-11 METAL CHIP

1-216-864-91 SHORT

1-216-836-11 METAL CHIP

1-218-720-11 METAL CHIP

1-218-720-11 METAL CHIP

1-218-720-11 METAL CHIP

R174 1-216-809-11 METAL CHIP

R181 1-218-720-11 METAL CHIP

R182 1-218-720-11 METAL CHIP

R183 1-218-720-11 METAL CHIP

R184 1-216-809-11 METAL CHIP

R191 1-216-817-11 METAL CHIP

R192 1-216-797-11 METAL CHIP

12

150K

560K

39K

47K

680K

120K

5.6K

100K

1K

100K

10K

0

18K

15K

15K

15K

100

15K

15K

15K

100

470

10

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

0.5%

Remark

Ref. No.

Part No.

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

1/16W

Description

< RESISTOR >

R811 1-249-415-11 CARBON

R812 1-249-417-11 CARBON

R813 1-249-419-11 CARBON

R814 1-249-421-11 CARBON

R815 1-247-843-11 CARBON

1/16W

1/16W

1/16W

1/16W

1/16W

R816 1-249-427-11 CARBON

R817 1-249-415-11 CARBON

R818 1-249-417-11 CARBON

R819 1-249-419-11 CARBON

R820 1-249-421-11 CARBON

1/16W

1/16W

0.5% 1/16W

0.5% 1/16W

R821 1-247-843-11 CARBON

R822 1-249-427-11 CARBON

R851 1-247-807-31 CARBON

R852 1-247-807-31 CARBON

< SWITCH >

5% 1/16W

0.5% 1/16W

0.5% 1/16W

0.5% 1/16W

5% 1/16W

3.3K

6.8K

100

100

5%

5%

< COMPOSITION CIRCUIT BLOCK >

1/16W

1/16W

680

1K

1.5K

2.2K

3.3K

6.8K

680

1K

1.5K

2.2K

5%

5%

5%

5%

S801 1-771-349-21 SWITCH, KEYBOARD (G)

S802 1-771-349-21 SWITCH, KEYBOARD (S)

S803 1-771-349-21 SWITCH, KEYBOARD (s)

S804 1-771-349-21 SWITCH, KEYBOARD (EX-CHANGE)

S805 1-771-349-21 SWITCH, KEYBOARD (DISC SKIP)

S806 1-771-349-21 SWITCH, KEYBOARD (j)

S807 1-771-349-21 SWITCH, KEYBOARD (J)

S808 1-771-349-21 SWITCH, KEYBOARD (EDIT)

S809 1-771-349-21 SWITCH, KEYBOARD (CHECK)

S810 1-771-349-21 SWITCH, KEYBOARD (CLEAR)

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

RB101 1-233-576-11 RES, CHIP NETWORK 100

RB102 1-233-576-11 RES, CHIP NETWORK 100

Remark

1/4W

1/4W F

1/4W

1/4W

S811 1-771-349-21 SWITCH, KEYBOARD (A)

S825 1-475-543-11 ENCODER, ROTARY (JOG)

************************************************************** < SWITCH >

S101 1-572-085-11 SWITCH, LEAF

1/4W F

1/4W F

1/4W F

1/4W F

1/4W

1/4W F

1/4W F

1/4W F

1/4W F

1/4W F

< VIBRATOR >

1-681-142-11 HP BOARD (CE375:US/CND)

*********

1-681-142-21 HP BOARD (CE375:AUS/AEP/UK/SP/E)

********* X191 1-767-408-21 VIBRATOR, CRYSTAL (16MHZ)

X191 1-767-430-11 VIBRATOR, CRYSTAL (16MHZ)

**************************************************************

1-681-139-11 DISPLAY BOARD (CE275,CE375:US/CND)

**************

1-681-139-21 DISPLAY BOARD (CE375:AUS/AEP/UK/SP/E)

**************

2-389-320-01 CUSHION

4-231-690-01 HOLDER (FL A)

C881 1-162-294-31 CERAMIC

C882

C883

< CAPACITOR >

1-162-294-31 CERAMIC

1-164-159-11 CERAMIC

0.001UF

10% 50V

(CE375)

0.001UF

10% 50V

(CE375)

0.1UF

50V

(CE375)

J881

< JACK >

1-770-306-11 JACK (LARGE TYPE) (CE375) < CONNECTOR >

* CN810 1-764-700-11 SOCKET, CONNECTOR 37P

CN811 1-750-194-11 CONNECTOR, BOARD TO BOARD 4P

FL801

< FILTER >

1-517-946-21 INDICATOR TUBE, FLUORESCENT

< RESISTOR >

R881

R882

1-249-401-11 CARBON

1-249-401-11 CARBON

47

47

5%

5%

1/4W F

(CE375)

1/4W F

(CE375)

**************************************************************

< IC >

IC802 8-759-827-70 IC NJL64H400A-1

36

CDP-CE275/CE375

KEY MAIN

Ref. No.

Part No.

Description

1-681-140-11 KEY BOARD (CE275,CE375:US/CND)

*****************************

1-681-140-21 KEY BOARD (CE375:AUS/AEP/UK/SP/E)

********************************

< CAPACITOR >

Remark

Ref. No.

Part No.

Description

A-4725-570-A MAIN BOARD, COMPLETE (CE275)

*********************

Remark

A-4725-571-A MAIN BOARD, COMPLETE (CE375:US/CND)

*********************

A-4725-579-A MAIN BOARD, COMPLETE

(CE375:AUS/AEP/UK/SP)

********************* C851 1-104-665-11 ELECT 100UF 20.00% 10V

< CONNECTOR > A-4725-581-A MAIN BOARD, COMPLETE (CE375:E)

*********************

CN812 1-750-185-11 CONNECTOR, BOARD TO BOARD 4P

7-685-871-01 SCREW +BVTT 3X6 (S)

< RESISTOR >

< CAPACITOR >

R824 1-249-415-11 CARBON

R825

R826

R827

R830

1-249-417-11 CARBON

1-249-419-11 CARBON

1-249-421-11 CARBON

1-249-415-11 CARBON

680

1K

1.5K

2.2K

680

5%

5%

5%

5%

5%

1/4W F

1/4W F

1/4W F

1/4W F

1/4W F

C301 1-161-494-00 CERAMIC

C302 1-104-665-11 ELECT

C303 1-161-494-00 CERAMIC

C304 1-164-159-11 CERAMIC

C325 1-161-494-00 CERAMIC

R831 1-249-417-11 CARBON

R832

R833

1-249-419-11 CARBON

1-249-421-11 CARBON

< SWITCH >

1K

1.5K

2.2K

5%

5%

5%

1/4W F

1/4W F

1/4W F

C326 1-104-665-11 ELECT

C351 1-126-963-11 ELECT

C401 1-126-965-11 ELECT

C404 1-126-965-11 ELECT

C407 1-162-290-31 CERAMIC

S812 1-771-349-21 SWITCH, KEYBOARD (DISC 5)

S812 1-771-349-41 SWITCH, KEYBOARD (DISC 5)

S813 1-771-349-21 SWITCH, KEYBOARD (DISC 4)

S813

S814

1-771-349-41 SWITCH, KEYBOARD (DISC 4)

1-771-349-21 SWITCH, KEYBOARD (DISC 3)

C451 1-126-933-11 ELECT

C501 1-126-965-11 ELECT

C504 1-126-965-11 ELECT

C507 1-162-290-31 CERAMIC

C551 1-126-933-11 ELECT S814 1-771-349-41 SWITCH, KEYBOARD (DISC 3)

S815 1-771-349-21 SWITCH, KEYBOARD (DISC 2)

S815 1-771-349-41 SWITCH, KEYBOARD (DISC 2)

S816

S816

1-771-349-21 SWITCH, KEYBOARD (DISC 1)

1-771-349-41 SWITCH, KEYBOARD (DISC 1)

S817 1-771-349-21 SWITCH, KEYBOARD (TIMER)

S817 1-771-349-41 SWITCH, KEYBOARD (TIMER)

S818 1-771-349-21 SWITCH, KEYBOARD (REPEAT)

S818

S819

1-771-349-41 SWITCH, KEYBOARD (REPEAT)

1-771-349-21 SWITCH, KEYBOARD (FADER)

S819 1-771-349-41 SWITCH, KEYBOARD (FADER)

S820 1-771-349-21 SWITCH, KEYBOARD (P.SEARCH)

S820 1-771-349-41 SWITCH, KEYBOARD (P.SEARCH)

S821 1-771-349-21 SWITCH, KEYBOARD (PLAY MODE)

S821 1-771-349-41 SWITCH, KEYBOARD (PLAY MODE)

**************************************************************

C602 1-126-937-11 ELECT

C603 1-126-767-11 ELECT

C608 1-126-934-11 ELECT

C609

C610

1-128-552-51 ELECT

1-126-964-11 ELECT

C611 1-126-767-11 ELECT

C613 1-126-935-11 ELECT

C616 1-161-494-00 CERAMIC

C619 1-104-665-11 ELECT

0 C620

1-113-924-11 CERAMIC

C622 1-164-159-11 CERAMIC

< CONNECTOR >

0.022UF

100UF

0.022UF

0.1UF

0.022UF

100UF

4.7UF

22UF

22UF

470PF

100UF

22UF

22UF

470PF

100UF

4700UF

1000UF

220UF

47UF

10UF

25V

20.00% 10V

25V

50V

25V

20.00% 16V

(CE375)

20.00% 50V

20.00% 50V

10% 50V

20.00% 16V

(CE375)

1000UF 20.00% 16V

470UF

0.022UF

100UF

20.00% 6.3V

25V

20.00% 10V

0.0047UF 20.00% 250V

0.1UF

20.00% 10V

20.00% 50V

20.00% 50V

20.00% 50V

10% 50V

20.00% 16V

20.00% 16V

20.00% 10V

20.00% 63V

20.00% 50V

50V

CN301 1-784-798-11 CONNECTOR, FFC 37P

CN302 1-568-838-11 CONNECTOR, FFC 21P

CN311 1-573-911-11 PIN, CONNECTOR 13P

CN351 1-506-468-11 PIN, CONNECTOR 3P (CE375)

CN603 1-792-131-11 LEAD (WITH CONNECTOR)

< DIODE >

D353 8-719-991-33 DIODE 1SS133T-77

D601 8-719-024-99 DIODE 11ES2-NTA2B

D602 8-719-024-99 DIODE 11ES2-NTA2B

D603 8-719-024-99 DIODE 11ES2-NTA2B

D604 8-719-024-99 DIODE 11ES2-NTA2B

The components identified by mark 0 or dotted line with mark 0 are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant le numéro spécifié.

37

CDP-CE275/CE375

MAIN

Ref. No.

Part No.

Description

D605 8-719-024-99 DIODE 11ES2-NTA2B

D606 8-719-110-08 DIODE RD8.2ESB2

D607 8-719-991-33 DIODE 1SS133T-77

D608 8-719-109-85 DIODE RD5.1ESB2

D609 8-719-991-33 DIODE 1SS133T-77

D610 8-719-983-79 DIODE MTZJ-T-72-27D

< GROUND TERMINAL BOARD >

EB601 1-537-770-21 TERMINAL BOARD, GROUND

< IC >

IC301 8-752-919-66 IC CXP82532-013Q

IC303 8-749-921-12 IC GP1F32T

IC350 8-759-145-58 IC BA4558

IC351 8-759-167-88 IC NJM4565D (CE375)

IC601 8-759-039-69 IC UPC7805AHF

IC602 8-749-011-78 IC BA17807T

IC603 8-759-165-82 IC PST600E-T

J301

L601

L602

Q301

Q307

Q352

Q353

Q356

< JACK >

1-785-868-11 JACK, PIN 2P

< COIL >

1-412-473-21 INDUCTOR

1-414-151-21 INDUCTOR

< TRANSISTOR >

0UH

470UH

8-729-119-78 TRANSISTOR

8-729-029-56 TRANSISTOR

8-729-029-56 TRANSISTOR

8-729-029-56 TRANSISTOR

8-729-029-56 TRANSISTOR

Q402 8-729-141-26 TRANSISTOR

Q405 8-729-141-26 TRANSISTOR

Q502 8-729-141-26 TRANSISTOR

Q505 8-729-141-26 TRANSISTOR

Q601 8-729-140-97 TRANSISTOR

< RESISTOR >

R301 1-249-429-11 CARBON

R302 1-249-429-11 CARBON

R304 1-249-429-11 CARBON

R305 1-247-807-31 CARBON

R306 1-249-429-11 CARBON

R307 1-247-807-31 CARBON

R308 1-249-441-11 CARBON

R320 1-249-427-11 CARBON

R321 1-249-427-11 CARBON

R322 1-249-427-11 CARBON

2SC2785-HFE

DTA144ESA-TP

DTA144ESA-TP

DTA144ESA-TP

DTA144ESA-TP

2SC3622A-LK

2SC3622A-LK

2SC3622A-LK

2SC3622A-LK

2SB734-34

R323

R324

R325

R326

R327

1-249-427-11 CARBON

1-249-429-11 CARBON

1-249-417-11 CARBON

1-249-425-11 CARBON

1-249-425-11 CARBON

R329 1-249-425-11 CARBON

R350 1-247-807-31 CARBON

R351 1-247-807-31 CARBON

6.8K

10K

1K

4.7K

4.7K

4.7K

100

100

10K

10K

10K

100

10K

100

100K

6.8K

6.8K

6.8K

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

Remark

Ref. No.

Part No.

Description

R352 1-249-441-11 CARBON

R353 1-249-441-11 CARBON

R356 1-249-441-11 CARBON

R401 1-247-895-00 CARBON

R402 1-249-419-11 CARBON

R403 1-249-419-11 CARBON

R404 1-249-429-11 CARBON

R405 1-249-429-11 CARBON

R406 1-247-895-00 CARBON

R414 1-249-409-11 CARBON

R415 1-249-409-11 CARBON

R419 1-249-421-11 CARBON

R420 1-249-409-11 CARBON

R422 1-249-421-11 CARBON

R451 1-247-843-11 CARBON

R452 1-249-429-11 CARBON

R501 1-247-895-00 CARBON

10K

470K

220

220

2.2K

220

2.2K

3.3K

100K

100K

100K

470K

1.5K

1.5K

10K

10K

470K

R502 1-249-419-11 CARBON

R503 1-249-419-11 CARBON

R504 1-249-429-11 CARBON

R505 1-249-429-11 CARBON

R506 1-247-895-00 CARBON

R514 1-249-409-11 CARBON

R515 1-249-409-11 CARBON

R519 1-249-421-11 CARBON

R520 1-249-409-11 CARBON

R522 1-249-421-11 CARBON

R551 1-247-843-11 CARBON

R552 1-249-429-11 CARBON

1.5K

1.5K

10K

10K

470K

220

220

2.2K

220

2.2K

3.3K

10K

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

R601 1-249-429-11 CARBON

R602 1-249-429-11 CARBON

R603 1-249-429-11 CARBON

R604 1-249-429-11 CARBON

R605 1-249-411-11 CARBON

R606 1-247-807-31 CARBON

R607 1-249-389-11 CARBON

10K

10K

10K

10K

330

100

4.7

5%

5%

5%

5%

5%

5%

5%

1/4W

1/4W

1/4W

1/4W

1/4W

S602

< SWITCH >

1-572-675-11 SWITCH, POWER VOLTAGE CHANGE

(VOLTAGE SELECTOR)(CE375:E)

< TRANSFORMER >

1/4W

1/4W

1/4W F

1/4W F

1/4W F

0 T601

0 T601

0 T601

1-435-342-11 TRANSFORMER, POWER

(CE275:US/CND,CE375:US/CND)

1-435-343-11 TRANSFORMER, POWER

(CE275:AUS,CE375:AUS/AEP/UK/SP)

1-435-344-11 TRANSFORMER, POWER (CE375:E)

1/4W F

1/4W

1/4W F

1/4W F

1/4W F

< VIBRATOR >

X301 1-579-175-11 VIBRATOR, CERAMIC

**************************************************************

1/4W F

1/4W

1/4W

The components identified by mark 0 or dotted line with mark 0 are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant le neméro spécifié.

1/4W

(CE375)

1/4W

(CE375)

1/4W

1/4W

1/4W

1/4W

1/4W

1/4W

1/4W F

1/4W F

1/4W F

1/4W

1/4W

1/4W

1/4W F

1/4W F

1/4W F

1/4W F

1/4W F

Remark

1/4W

1/4W

1/4W

1/4W

1/4W F

1/4W F

1/4W

1/4W

1/4W

1/4W F

1/4W F

1/4W F

1/4W F

1/4W F

1/4W

(CE375)

1/4W

(CE375)

1/4W

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

5%

38

POWER SW

LOADING MOTOR

CDP-CE275/CE375

SENSOR JUNCTION

R10

R11

R12

R21

R22

R23

R24

R25

R26

Ref. No.

Part No.

Description Remark

1-681-141-11 POWER SW BOARD (CE275,CE375:US/CND)

****************

Ref. No.

Part No.

Description

< SWITCH >

Remark

1-681-141-21 POWER SW BOARD

****************

(CE375:AUS/AEP/UK/SP/E)

S11 1-771-836-11 SWITCH, LEVER (SLIDE)

**************************************************************

< CAPACITOR >

0 C601

1-113-924-11 CERAMIC

< CONNECTOR >

0.0047UF 20.00% 250V

0 9

0 9

0 9

0 9

0 9

1-575-651-21 CORD, POWER (CE375:AEP/UK/SP)

1-696-845-11 CORD, POWER (CE275:AUS,CE375:AUS)

1-777-071-41 CORD, POWER (CE375:AEP/UK/SP)

1-783-528-21 CORD, POWER (TRACKING)(CE375:E)

1-783-531-31 CORD, POWER

(CE275:US/CND,CE375US/CND)

* CN601

1-580-230-31 PIN, CONNECTOR (PC BOARD) 2P

* CN602 1-568-226-11 PIN, CONNECTOR 2P

0 S601

< SWITCH >

1-762-581-11 SWITCH, AC POWER PUSH (1 KEY)

**************************************************************

1-676-246-11 JUNCTION BOARD

***************

0 T601

1-435-342-11 TRANSFORMER, POWER

(CE275:US/CND,CE375:US/CND)

0 T601

1-435-343-11 TRANSFORMER, POWER

(CE275:AUS,CE375:AUS/AEP/UK/SP)

0 T601

1-435-344-11 TRANSFORMER, POWER (CE375:E)

60 1-792-486-11 WIRE (FLAT TYPE)(37 CORE)

FL801 1-517-946-21 INDICATOR TUBE, FLUORESCENT

1-676-244-11 LOADING MOTOR BOARD

*********************

**************************************************************

1-676-245-11 SENSOR BOARD

**************

111

116

160

0 201

202

1-791-930-11 WIRE (FLAT TYPE)(6 CORE)

1-757-648-11 WIRE (FLAT TYPE)(21 CORE)

1-418-746-11 ENCODER, ROTARY

1-796-033-11 LIGHT PICK UP (PXR-104X)

1-782-817-11 WIRE (FLAT TYPE)(16 CORE)

**************************************************************

ACCESSORIES & PACKING MATERIALS

********************************

< CAPACITOR >

MISCELLANEOUS

***************

C10

C11

CN10

CN11

D10

D11

IC11

1-124-589-11 ELECT

1-161-494-00 CERAMIC

< CONNECTOR >

< DIODE >

8-749-924-18 PHOTO INTERRUPTER RPI-1391

8-749-017-45 SENSOR, PHONT RPR-220C1N

< IC >

8-759-356-03 IC BA6780

< RESISTOR >

47UF

0.022UF

1-750-243-11 SOCKET, CONNECTOR 6P

1-573-911-11 PIN, CONNECTOR 13P

CN13 1-506-481-11 PIN, CONNECTOR 2P

* CN14

1-568-941-11 PIN, CONNECTOR 3P

CN15 1-784-767-11 CONNECTOR, FFC 6P

20% 16V

25V

1-418-857-11 COMMANDER, STANDARD (RM-DC345)

(CE375:AUS/AEP/UK/SP/E)

1-476-132-11 REMOTE COMMANDER (RM-DC355)

(CE375:US/CND)

1-558-271-11 CORD, CONNECTION

4-233-300-11 MANUAL, INSTRUCTION (ENGLISH)

(CE275:US,CE375:US)

4-233-300-21 MANUAL, INSTRUCTION (ENGLISH, FRENCH)

(CE275:CND,CE375:CND)

4-233-300-31 MANUAL, INSTRUCTION (ENGLISH, FRENCH,

GERMAN, SPANISH, DUTCH, SWEDISH,

ITALIAN, PORTUGUESE) (CE375:AEP)

4-233-300-51 MANUAL, INSTRUCTION

(ENGLISH, FINNISH, PORTUGUESE, RUSSIAN)

(CE375:SP,CE375:E)

4-233-300-61 MANUAL, INSTRUCTION (ENGLISH)

(CE275:AUS,CE375:AUS/UK)

4-234-873-01 COVER, BATTERY(RM-DC345)

(CE375:AUS/AEP/UK/SP/E)

4-981-643-01 COVER, BATTERY(RM-DC355)

(CE375:US/CND)

1-249-416-11 CARBON

1-249-407-11 CARBON

1-249-429-11 CARBON

1-249-429-11 CARBON

1-249-426-11 CARBON

1-249-425-11 CARBON

1-249-430-11 CARBON

1-249-382-11 CARBON

1-249-382-11 CARBON

820

150

10K

10K

5.6K

4.7K

12K

1.2

1.2

5%

5%

5%

5%

5%

5%

5%

5%

5%

1/4W F

1/4W F

1/4W

1/4W

1/4W

1/4W F

1/4W

1/6W F

1/6W F

The components identified by mark 0 or dotted line with mark 0 are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque 0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant le neméro spécifié.

39

CDP-CE275/CE375

REVISION HISTORY

Clicking the version allows you to jump to the revised page.

Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.

Ver.

1.1

Date

2001.07

1.0

2001.04

• Addition of test mode

• Addition of electrical adjustments

New

Description of Revision

40

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals