A/V Equipment
Chabot College Standard
Classroom Template
Revised 1/19/2012
General Functions
1. Presenter’s Station
2. Resident PC
3. Local monitor
4. VHS/DVD combo player
5. Closed Captioning Decoder
6. Ceiling mounted projection system
7. Ceiling mounted speakers
8. Motorized Screen
9. Input plate as Shown LWC/ Panel Crafter Custom 1RU Input plate
To be made by contractor
Video and Audio systems
1. Panasonic PT-FW430 Set up for 16x10 aspect
2. Spare Panasonic long-life lamp .
3. Chief RPMA1 Security Mount
4. Security set screws for RPMA1 mount.
5. Motorized projection screen minimum 100 in diag. but gauged to size of
room.
6. PC and monitor supplied by the college .
7. Toshiba SD-V296 DVD/VCR combo or current model.
8. Link PCD88 Closed caption decoder.
9. Atlas FAP42T Ceiling Speakers or equivalent
10. TOA 120W 70V Audio Amplifier.
11. Kramer 4x4 VGA Matrix Switcher
12. SP Controls SP3-AFVP+ Audio pre-amp Switcher
13. Interlink VP4150 remote Power Point presenter with pointer.
14. Furman PS-8R-II Power Sequencer
15. Tripplite RS1215 Power Strip.
16. Elmo Document Camera TT-02rx or equivalent.
17. EVO flat panel monitor arm.
Coordinate with owner on location.
CONTROL SYSTEM
1.
2.
3.
4.
5.
6.
7.
SP controls Pixie pro system
Pixie pro acrylic enclosure, White
PX2-NRC-1142 Controller
2ea. SP 232/IR PUC
1ea. SP REL-4 PUC
SP Catlinc VGA
SP Catlinc
HDMI
D12SD-*
THE TEACHING STATION
Middle Atlantic D12SD-HM
12 space dual bay outboard rack w/square top + doors/cooling system
Color of Square top 54 Inches wide.
AV System Cabling - Chabot College
The following structured cabling needs to be included in each room between
the ceiling equipment and the teaching station.
Cat6a cabling for the catlinc extenders (HDMI and VGA) 3 each
A 1 input 2 output HDMI distribution amplifier to feed 2nd HDMI
extender.
2 pair shielded 22 gauge for control RS232 cabling
1 pair non-shielded 18 gauge for speaker wiring.
RG59 Coax for composite video to the projectors.
All internal wiring for the teaching station needs to be provided by AV
contractor.
In the rooms with two projectors the following additional equipment will
be necessary:
1 additional SP Controls RS232/IR Puck for the second projector.
A simple 1 in 2 out composite video D/A.
1 - VGA male to VGA male cable to run from the pass-thru of
one projector to the input of the second projector.
S
P
E
P ro d u c t N u m b e r :
PT-FW430
P ro d u c t N a m e :
LCD Projector
C
F
I
L
E
As of March 2011. Specifications and appearance are subject to change without notice.
SFL11M005-1
1/14
S
P
E
C
F
I
L
E
PT-FW430
LCD Projector
Specifications
Main unit
Power supply
Power consumption
LCD panel
Panel size
Display method
Pixels
Pixel configuration
Lens
Throw ratio
Lamp
Screen size
Colors
Brightness* 2
Center-to-corner uniformity* 2
Contrast* 2
Resolution
Scanning frequency
HDMI/DVI-I (digital)
DVI-I (analog)/RGB
YPBPR (YCBCR)
Video/S-Video
Optical axis shift
Keystone correction range
Installation
Built-in speaker
Size
Output power
Terminals
HDMI IN
As of March 2011
SFL11M005-1
100 –240 V AC, 3.9 –1.4 A, 50/60 Hz
330 W
(0.3 W at 100 –120 V AC, 0.4 W at 220 – 240 V AC when standby mode
set to eco,* 1 9 W when standby mode set to normal, 20 W when
standby mode set to normal and audio monitor out.)
18.9 mm (0.74 inches) diagonal (16:10 aspect ratio)
Transparent LCD panel (× 3, R/G/B)
1,024,000 (1,280 × 800) × 3, total of 3,072,000 pixels
Stripe
Manual (2× zoom), manual focus F 1.7– 2.6, f 21.6 – 43.0 mm
1.34 – 2.68:1
250 W UHM lamp
0.84 –7.62 m (33 – 300 inches) diagonally, 16:10 aspect ratio
Full color (16,777,216 colors)
3,500 lumens
80%
600:1 (full on/full off)
1,280 × 800 pixels (Input signals that exceed this resolution will be
converted to 1,280 × 800 pixels.)
fH: 27.0 kHz – 68.7 kHz, fV: 24 .0 Hz – 85.0 Hz,
dot clock: 25 .2 MHz –148.5 MHz
fH: 15 .6 kHz – 91.1 kHz, fV: 24 .0 Hz – 85.1 Hz,
dot clock: 162 MHz or lower
480i (525i):
fH 15.75 kHz; fV 60 Hz,
576i (625i):
fH 15.63 kHz; fV 50 Hz,
480p (525p):
fH 31.50 kHz; fV 60 Hz,
576p (625p):
fH 31.25 kHz; fV 50 Hz,
720 (750)/60p:
fH 45.00 kHz; fV 60 Hz,
720 (750)/50p:
fH 37.50 kHz; fV 50 Hz,
1080 (1125)/60i: fH 33.75 kHz; fV 60 Hz,
1080 (1125)/50i: fH 28.13 kHz; fV 50 Hz,
1080 (1125)/24p: fH 27.00 kHz; fV 24 Hz,
1080 (1125)/60p: fH 67.50 kHz; fV 60 Hz,
1080 (1125)/50p: fH 56.25 kHz; fV 50 Hz
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Vertical: ±51% from center of screen (manual),
horizontal: ±24% from center of screen (manual)
Vertical: ±30°
Ceiling/desk, front/rear (menu selection)
4 cm (1-9/16 inches) (round) × 1
5.0 W (monaural)
HDMI 19-pin × 1, Deep Color, HDCP compatible
480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p,
1080 (1125)/60i, 1080 (1125)/50i, 1080 (1125)/24p, 1080 (1125)/60p,
1080 (1125)/50p
VGA (640 × 480) – WSXGA+ (1,680 × 1,050), compatible with noninterlaced signals only, dot clock: 25 .2 MHz –146.25 MHz
Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz,
32 kHz)
2/14
S
P
E
C
F
I
L
E
PT-FW430
LCD Projector
DVI-I IN* 3
Digital
R, G, B
DVI-I 29-pin × 1
DVI 1.0 compliant, compatible with HDCP, compatible with single link
only
480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p,
1080 (1125)/60i, 1080 (1125)/50i, 1080 (1125)/24p, 1080 (1125)/60p,
1080 (1125)/50p
VGA (640 × 480) – WSXGA+ (1,680 × 1,050), compatible with noninterlaced signals only, dot clock: 25 .2 MHz –146.25 MHz
G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;
B, R: 0.7 Vp-p, 75 ohms;
HD/VD, SYNC: high impedance, TTL (positive/negative)
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y, PB (CB), PR (CR)
COMPUTER (RGB) IN
R, G, B
Y: 1.0 Vp-p (including sync signal);
PB (CB), PR (CR): 0.7 Vp-p, 75 ohms
D-sub HD 15-pin (female) × 1
G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;
B, R: 0.7 Vp-p, 75 ohms;
HD/VD, SYNC: high impedance, TTL (positive/negative)
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y, PB (CB), PR (CR)
VIDEO IN
S-VIDEO IN
AUDIO IN 1
AUDIO IN 2
AUDIO IN 3
AUDIO OUT
SERIAL IN
LAN
WIRELESS MODULE
Power cord length
Cabinet materials
Dimensions (W × H × D)
Weight
Operation noise
Operating temperature
Operating humidity
Remote control unit
Power supply
Operation range* 6
Dimensions (W × H × D)
Weight
Y: 1.0 Vp-p (including sync signal);
PB (CB), PR (CR): 0.7 Vp-p, 75 ohms
RCA pin × 1, 1.0 Vp-p, 75 ohms
Mini DIN 4-pin × 1, Y: 1.0 Vp-p; C: 0.286 Vp-p, 75 ohms
M3 × 1 (L, R × 1), input impedance: 22 kilohms or more
M3 × 1 (L, R × 1), 0.5 Vrms, input impedance: 22 kilohms or more
RCA × 2 (L, R × 1), 0.5 Vrms, input impedance: 22 kilohms or more
M3 × 1 (L, R × 1) (monitor out: 0 – 2.0 Vrms, variable)
D-sub 9-pin (female) × 1, for external control (RS-232C compliant)
RJ-45 × 1, for network connection, 100Base-TX/10Base-T, compliant
with PJLink™
Connector for optional wireless module ET-WM200U/WM200E × 1
2.0 m (6 ft 7 in)
Molded plastic (PC + ABS)
430 mm × 125.5 mm* 4 × 323 mm
(16-15/16 × 4-15/16* 4 × 12-23/32 inches) (including the lens)
Approximately 6.0 kg (13.2 lbs)
33 dB (lamp mode: NORMAL), 29 dB (lamp mode: ECO)
0°–40°C (32°–104°F)* 5
20%– 80% (no condensation)
3 V DC (R6/LR6/AA type battery × 2)
Approximately 15 m (49 ft 3 in) when operated from directly in front of
the signal receptor
48 × 163 × 24.5 mm (1-13/32˝ × 6-5/8˝ × 31/32˝)
Approx. 117 g (4.1 oz) (including batteries)
Supplied accessories
Power cord with security lock (× 1)
Wireless remote control unit (× 1)
Batteries for remote control (AA/R6/LR6 type × 2)
Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring
and Control Software Ver. 2.5, Wireless Manager ME 5.5) (× 1)
As of March 2011
SFL11M005-1
3/14
S
P
E
C
F
I
L
E
PT-FW430
LCD Projector
Wireless Manager ME 5.5 system requirements
OS
Web browser
CPU
Memory
Free hard disk space
CD-ROM drive
Wireless LAN
To use network functions, a PC is required that meets the conditions
given below.
Microsoft®
Windows® XP:
Professional 32-bit, Home Edition 32-bit, Tablet PC
Edition 2005 32-bit
Windows Vista®: Ultimate 32-bit/64-bit, Business 32-bit/64-bit, Home
Premium 32-bit/64-bit, Home Basic 32-bit/64-bit
Windows® 7:
Ultimate 32-bit/64-bit, Professional 32-bit/64-bit,
Home Premium 32-bit/64-bit
Apple Mac OS X* 7 : v10.4, v10.5, v10.6
Windows®:
Internet Explorer 6.0/7.0/8.0
Mac OS:
Safari 2.0/3.0/4.0
Windows®:
1 GHz or higher Intel® Pentium® III or higher, or
other compatible processor
Mac OS X:
1 GHz or higher PowerPC G4, or 1.8 GHz or higher
Intel® Core™ processor
256 MB or more (512 MB or higher is recommended for Mac OS X)
60 MB or more
CD-ROM drive or DVD drive (required for installation)
The optional ET-WM200 is required.
IEEE 802.11b/g/n compatible (built-in wireless LAN system or external
IEEE 802.11b/g/n LAN card must be installed and running normally.)
NOTE: Wireless connection may not be possible with some IEEE 802.11b/g/n wireless
LAN systems. Macintosh computers must have a built-in wireless LAN adapter.
For IEEE 802.11n connection, use a wireless LAN adapter, projector and access
point that are IEEE 802.11n compatible, and connect with Infrastructure mode.
Wired LAN connector
Optional accessories
Replacement lamp unit
Replacement filter unit
Ceiling mount bracket
Wireless module
RJ-45
ET-LAF100A
ET-EMF100
ET-PKF110H (for high ceilings)
ET-PKF110S (for low ceilings)
ET-WM200U (for North America)
ET-WM200E (for Europe and Asia)
Weights and dimensions shown are approximate. Specifications subject to change without notice.
* 1 When the standby mode is set to ECO, network functions such as power on over the LAN network will not operate. Also, only certain commands can be received for external control using the serial terminal.
* 2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
* 3 The DVI-I IN terminal also accepts analog signals.
* 4 With legs at shortest position.
* 5 Operation range differs depending on environments.
* 6 The operating temperature range is 0°C–35°C (32°F–95°F) when used in High-Altitude mode (1,400 m (4,593 ft) to 2,700 m (8,858 ft)).
* 7 The operation system must be pre-installed at the factory or clean installed.
As of March 2011
SFL11M005-1
4/14
S
P
E
F
C
I
L
E
PT-FW430
LCD Projector
Dimensions
115
(4-17/32)
10.5
(13/32)
71
(2-25/32)
125.5
(4-15/16 )
323
(12-23/32)
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
53
(2-3/32)
430
(16-15/16 )
228.5
(9)
Terminals
1
2
LAN
3
4
DVI-I IN
5
COMPUTER IN
6
AUDIO IN
AC IN
7
8
VIDEO
IN
R
LAN connector
2
HDMI input
3
DVI-I input
4
Computer input
5
S-Video input
6
Video input
7
Serial input
8
Audio input 1
9
Audio input 2
S-VIDEO IN
IN
SERIAL IN
1
AUDIO IN 3
L
VARIABLE
AUDIO OUT
MAIN
POWER
OFF
ON
9 10
11
10 Audio input 3
11 Audio out put
As of March 2011
SFL11M005-1
5/14
S
P
E
F
C
I
L
E
PT-FW430
LCD Projector
Standard setting-up position
∅42 (1-11/16)
H
Upper edge of projected image
L
369– 449
(14-17/32–
17-11/16)
Adjustable in
20-mm
(15/32-inch) step.
∅49 (1-15/16)
** Adjustable in 20 mm (25/32˝) steps.
194
(7-5/8)
Projected image
H
L
Lower edge of projected image
NOTE:
Illustrations show the projector
installed using optional ceiling mount
bracket ET-PKF110H.
65
(2-9/16)
70
(2-3/4)
This illustration is not drawn to scale.
13 (1/2)
L
Projected image
unit : mm (inch)
Projection distance for 16:10 aspect ratio screen
unit: meters (feet)
Projection size
[diagonal]
0.84
1.02
1.27
1.52
1.78
2.03
2.29
2.54
3.05
3.81
5.08
6.35
7.62
m
m
m
m
m
m
m
m
m
m
m
m
m
/
/
/
/
/
/
/
/
/
/
/
/
/
33˝
40˝
50˝
60˝
70˝
80˝
90˝
100˝
120˝
150˝
200˝
250˝
300˝
Projection distance [L]
Min [wide]
–
1.1
1.4
1.7
2.0
2.3
2.6
2.9
3.4
4.3
5.7
7.2
8.6
(–)
(3.6)
(4.6)
(5.5)
(6.5)
(7.4)
(8.4)
(9.3)
(11.2)
(14.1)
(18.8)
(23.6)
(28.3)
Max [telephoto]
1.8
2.3
2.8
3.4
4.0
4.6
5.1
5.7
6.9
8.6
11.5
14.3
17.2
(6.0)
(7.4)
(9.2)
(11.1)
(13.0)
(14.9)
(16.8)
(18.7)
(22.5)
(28.1)
(37.6)
(47.0)
(56.5)
Height from the edge of screen
to center of lens [ H ]
0
0
0
-0.01
-0.01
-0.01
-0.01
-0.01
-0.02
-0.02
-0.03
-0.04
-0.05
–
–
–
–
–
–
–
–
–
–
–
–
–
0.45
0.54
0.68
0.81
0.95
1.09
1.22
1.36
1.63
2.04
2.73
3.41
4.09
(0
(0
(0
(0
(0
(0
(0
(0
(-0.1
(-0.1
(-0.1
(-0.1
(-0.2
–
–
–
–
–
–
–
–
–
–
–
–
–
1.5)
1.8)
2.3)
2.7)
3.2)
3.6)
4.1)
4.5)
5.3)
6.7)
8.9)
11.2)
13.4)
NOTE:
• The value for H (the height from the edge of the screen to the centre of the lens) is the value when the horizontal optical axis shift function is
not used. The value decreases when the horizontal optical axis shift function is used. For details, see Shift range on page 8.
• The value for L (distance to screen) varies slightly depending on the zoom lens characteristics.
• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
• The brightness varies depending on the zoom setting.
As of March 2011
SFL11M005-1
6/14
S
P
E
C
F
I
L
E
PT-FW430
LCD Projector
Projection distance for 16:9 aspect ratio screen
unit: meters (feet)
Projection size
[diagonal]
0.84
1.02
1.27
1.52
1.78
2.03
2.29
2.54
3.05
3.81
5.08
6.35
7.62
m
m
m
m
m
m
m
m
m
m
m
m
m
/
/
/
/
/
/
/
/
/
/
/
/
/
33˝
40˝
50˝
60˝
70˝
80˝
90˝
100˝
120˝
150˝
200˝
250˝
300˝
Projection distance [L]
Min [wide]
–
1.2
1.5
1.7
2.0
2.3
2.6
2.9
3.5
4.4
5.9
7.4
8.9
(–)
(3.8)
(4.7)
(5.7)
(6.7)
(7.6)
(8.6)
(9.6)
(11.5)
(14.5)
(19.3)
(24.2)
(29.1)
Max [telephoto]
1.9
2.3
2.9
3.5
4.1
4.7
5.3
5.9
7.1
8.8
11.8
14.7
17.7
(6.2)
(7.6)
(9.5)
(11.5)
(13.4)
(15.3)
(17.3)
(19.2)
(23.1)
(28.9)
(38.6)
(48.4)
(58.1)
Height from the edge of screen
to center of lens [ H ]
-0.02
-0.03
-0.04
-0.05
-0.06
-0.07
-0.08
-0.08
-0.10
-0.13
-0.17
-0.22
-0.26
–
–
–
–
–
–
–
–
–
–
–
–
–
0.44
0.53
0.66
0.80
0.93
1.06
1.20
1.33
1.60
2.00
2.66
3.33
4.00
(-0.1
(-0.1
(-0.1
(-0.1
(-0.2
(-0.2
(-0.2
(-0.2
(-0.3
(-0.4
(-0.6
(-0.7
(-0.9
–
–
–
–
–
–
–
–
–
–
–
–
–
1.5)
1.8)
2.2)
2.6)
3.1)
3.5)
4.0)
4.4)
5.3)
6.6)
8.8)
11.0)
13.2)
NOTE:
• The value for H (the height from the edge of the screen to the centre of the lens) is the value when the horizontal optical axis shift function is
not used. The value decreases when the horizontal optical axis shift function is used. For details, see Shift range on page 8.
• The value for L (distance to screen) varies slightly depending on the zoom lens characteristics.
• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
• The brightness varies depending on the zoom setting.
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 16:10
minimum
L (m) = (diagonal screen size in inches) × 0.0289 – 0.046
maximum
L (m) = (diagonal screen size in inches) × 0.0576 – 0.061
Aspect ratio 16:9
minimum
L (m) = (diagonal screen size in inches) × 0.0297 – 0.045
maximum
L (m) = (diagonal screen size in inches) × 0.0592 – 0.061
NOTE:
Distances calculated with the above equations will include a slight error.
As of March 2011
SFL11M005-1
7/14
S
P
E
C
F
I
L
E
PT-FW430
LCD Projector
Shift range
Optical axis shift function allows to shift the position of a projected image as shown below.
H
(Width of
projected image)
0.24H
0.51V
0.51V
V
(Height of
projected image)
0.24H
Standard position
of projected image
Installable angle
Install the projector at an angle within the range shown below.
• Horizontal direction
The projector may not be angled horizontally.
+30
°
• Vertical direction
The projector may be installed at a vertical
angle of 30°.
–30°
0°
As of March 2011
SFL11M005-1
8/14
S
P
E
F
C
I
L
E
PT-FW430
LCD Projector
List of compatible signals
The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 15.6 kHz to 91.1 kHz, vertical scanning frequencies of 24.0 Hz to 85.1 Hz, and a dot clock
of 162 MHz maximum can be input.
NOTE:
The native resolution of this projector is 1,280 × 800 pixels. If the display resolution of the input signal is different from the
native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
Display mode
Display
resolution
(dots) * 1
NTSC/NTSC4.43/
PAL-M/PAL60
720 × 4 8 0 i
1 5 .7
59.9
–
720 × 5 7 6 i
720 × 4 8 0 i
720 × 5 7 6 i
720 × 483
720 × 576
1,280 × 7 2 0
1,280 × 7 2 0
1,920 × 1 ,0 8 0 i
1 5 .6
1 5 .7
1 5 .6
3 1 .5
3 1 .3
4 5 .0
3 7 .5
3 3 .8
2 8 .1
2 7 .0
6 7 .5
5 6 .3
6 6 .6
5 5 .6
3 1 .5
3 7 .9
3 1 .5
3 5 .0
3 7 .9
3 7 .5
4 3 .3
3 5 .2
3 7 .9
4 8 .1
4 6 .9
5 3 .7
4 9 .7
3 9 .6
4 8 .4
5 6 .5
6 0 .0
6 8 .7
4 4 .8
3 7 .1
3 9 .6
4 7 .8
4 1 .3
4 9 .1
4 9 .7
6 4 .0
6 7 .5
7 6 .7
6 8 .7
6 0 .0
6 4 .0
8 0 .0
9 1 .1
6 4 .0
6 5 .1
5 5 .9
7 5 .0
6 5 .3
7 4 .6
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
24.0
60.0
50.0
59.9
49.9
70.1
85.1
59.9
66.7
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
74.6
50.1
60.0
70.1
75.0
85.0
59.9
49.8
49.9
59.9
50.0
60.2
59.8
71.2
74.9
85.0
75.1
60.0
60.0
75.0
85.0
60.0
59.9
59.9
60.0
60.0
59.9
–
13.5
13.5
27.0
27.0
74.3
74.3
74.3
74.3
74.3
148.5
148.5
138.5
141.5
25.2
31.5
25.2
30.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
57.3
51.9
65.0
75.0
78.8
94.5
74.5
60.5
65.3
79.5
68.0
69.1
83.5
94.2
108.0
121.5
100.0
108.0
108.0
135.0
157.5
108.0
122.4
106.5
162.0
146.3
154.0
PAL/PAL-N/SECAM
480i (525i)
576i (625i)
480p (525p)
576p (625p)
720 (750)/60p
720 (750)/50p
1080 (1125)/60i
1080 (1125)/50i
1080 (1125)/24p
1080 (1125)/60p
1080 (1125)/50p
1920 × 1080
1,920 × 1 ,0 8 0
VESA
640 × 400
VGA
640 × 480
SVGA
800 × 600
MAC
XGA
832 × 624
1,024 × 7 6 8
WIDE750 (720)
1,280 × 7 2 0
WXGA768
1,280 × 7 6 8
WXGA800
1,280 × 8 0 0
MXGA
1,152 × 8 6 4
MAC
MSXGA
SXGA
1,152 × 8 7 0
1,280 × 9 6 0
1,280 × 1 ,0 2 4
SXGA60+
1,400 × 1 ,0 5 0
WXGA+
UXGA
WSXGA+
WUXGA
1,440
1,600 ×
1,680 ×
1,920 ×
× 900
1 ,2 0 0
1 ,0 5 0
1 ,2 0 0
Scanning frequency Dot clock
frequency
H
V
(MHz)
(kHz)
(kHz)
Format
VIDEO/S-VIDEO
Plug and Play compatibility
HDMI
DVI-D input
Computer/
input
EDID1
EDID2
DVI-I (analog)
No
No
No
No
COMPUTER/YP B P R
HDMI/DVI/COMPUTER/YP B P R
Yes
Yes
COMPUTER
No
No
HDMI/DVI/COMPUTER
COMPUTER
Yes
No
Yes
No
Yes
No
Yes
HDMI/DVI/COMPUTER
COMPUTER
Yes
No
Yes
No
HDMI/DVI/COMPUTER
No
Yes
No
Yes
Yes
Yes
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
COMPUTER
HDMI/DVI/COMPUTER
COMPUTER
HDMI/DVI/COMPUTER
COMPUTER
No
Yes
HDMI/DVI/COMPUTER
COMPUTER
Yes
No
Yes
No
No
Yes
No
HDMI/DVI/COMPUTER
COMPUTER
Yes
No
Yes
No
Yes
No
* 1 The “i” appearing after the resolution indicates an interlaced signal.
As of March 2011
SFL11M005-1
9/14
S
P
E
F
C
I
L
E
PT-FW430
LCD Projector
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below.
Pin assignments and signal names
6
9
1
5
No. Signal name
Description
No. Signal name
Description
1
–
NC
6
–
Connected internally
2
TXD
Send data
7
RTS
Connected internally
3
RXD
Receive data
8
CTS
Connected internally
4
–
NC
9
–
NC
5
GND
Ground
D-sub 9-pin (female)
Serial input
Communication conditions (factory setting)
Signal level
RS-232C-compliant
Synchronization method
Start-stop synchronization
Baud rate
9,600 bps
Parity
None
Character length
8 bits
Stop bit
1 bit
X parameter
None
S parameter
None
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
STX
A
D
Start
(2 bytes)
(1 byte)
I1 I2
;
C1 C2 C3
:
P1 P2 ... Pn
ETX
Semicolon
Colon
End
(1 byte)
(1 byte)
(1 byte)
Parameters
ID 2 characters
Command
(undefined length)
(2 bytes)
(3 bytes)
(Control and/or query commands)
ID designator:
01 to 06: Projector ID number
ZZ: All units (ID ALL)
CAUTION
• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then try sending or receiving again.
• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next
command.
• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for command response to 10
seconds or more.
• When using two or more units, set different IDs for each unit.
As of March 2011
SFL11M005-1
10/14
S
P
E
C
F
I
L
E
PT-FW430
LCD Projector
Cable specifications
Projector
1
PC (DTE)
NC
NC
2
2
3
3
4
NC
NC
NC
NC
6
7
7
8
8
9
4
5
5
6
1
NC
NC
9
Control commands
Command: <Parameter>
Function
Callback: <Parameter>
P ON * 1
P OF * 1
AVL:<pl>
IIS:<input signal>
OST
OFZ:<off on>
OEN
OXG: 0
OXG: 1
OXG: 2
VPM:<NAT>
VPM:<STD>
VPM:<CIN>
VPM:<DYN>
VPM:<BBD>
VPM:<WBD>
VXX:DLVI0=<+00000>
VXX:DLVI0=<+00001>
VXX:DLVI0=<+00002>
AUU
AUD
OMN
OCU
OCD
OCL
OCR
OAS
O SH * 1/* 2
OIX
DZU
DZD
TSD:<date>
TST:<time>
Power on (standby mode on)
Power off (standby mode off)
Volume control
Input signal selection
The same function as “default” button
Freeze
Enter
Wide mode: Off
Wide mode: On
Wide mode: Auto
Picture mode: Natural
Picture mode: Standard
Picture mode: Cinema
Picture mode: Dynamic
Picture mode: Blackboard
Picture mode: Whiteboard
Daylight View: Off
Daylight View: Auto
Daylight View: On
Volume up
Volume down
Menu
Cursor up
Cursor down
Cursor left
Cursor right
Auto setup
AV mute
Index window
Digital zoom: Enlargement
Digital zoom: Reduction
Date setting
Time setting
PON * 1
POF * 1
AVL:<pl>
IIS:<input signal>
OST
OFZ:<off on>
OEN
OXG: 0
OXG: 1
OXG: 2
VPM:<NAT>
VPM:<STD>
VPM:<CIN>
VPM:<DYN>
VPM:<BBD>
VPM:<WBD>
VXX:DLVI0=<+00000>
VXX:DLVI0=<+00001>
VXX:DLVI0=<+00002>
AUU
AUD
OMN
OCU
OCD
OCL
OCR
OAS
OSH * 1/* 2
OIX
DZU
DZD
TSD:<date>
TST:<time>
Parameter value
Min
Max
–
–
0
–
–
0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
63
–
–
1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
* 1 Do not send PON, POF or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle.
* 2 When a command that cannot be executed during standby mode is sent, the projector will send an ER401 command in reply.
As of March 2011
SFL11M005-1
11/14
S
P
E
C
F
I
L
E
PT-FW430
LCD Projector
Status request commands
Command
Description
QPW
Q$S
QIN
QAV
QVC
QVT
QVB
QVR
QVS
QHP
QVP
QCP
QDC
QSP
QLG
QXG
Standby power status
Lamp status
Input signal status
Volume adjustment value
Color adjustment value
Tint adjustent value
Brightness adjustment value
Contrast adjustment value
Sharpness adjustment value
Horizontal position adjustment value
Vertical position adjustment value
Clock phase adjustment value
Dot clock adjustment value
Projection method status
On-screen menu language
Wide mode status
QVX:DLVI0
Daylight View status
QPM
QFZ
Q$L
QSH
QKS
QTE
QGD
QGT
Off
On
Auto
Picture mode status
Off
Auto
On
Natural
Standard
Cinema
Freeze status
Dynamic
Lamp run time
Blackboard
AV mute function statusWhiteboard
Keystone correction status
Color temperature adjustment status
Date setting status
Time setting status
Callback
<Parameter>
<power condition>
<lamp condition>
<input signal>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<0>
<1>
<2>
<+00000>
<+00001>
<+00002>
<NAT>
<STD>
<CIN>
<DYN>
<BBD>
<WBD>
<off_on>
<acctch>
<off_on>
<pl>
<color temp>
<date>
<time>
NOTE: If a wrong command is received, the projector will send an ER401 command to the computer.
As of March 2011
SFL11M005-1
12/14
S
P
E
C
F
I
L
E
PT-FW430
LCD Projector
Parameter format
Parameter format
<pl>
<off on>
<input signal>
<power condition>
<lamp condition>
<acctch>
<color temp>
<date>
<time>
Size (Byte)
Definition
3 (1 or 2 bytes also Decimal without signs: 0 –999 (000, 001, 002...999)
possible when
Decimal with signs: -99 to +99 (-99...-01, +00, +01, +02...+99)
under control)
Callback from the projector is 3 Byte.
1
0 = off, 1 = on
3
HD1 = HDMI, DVI = DVI-I, RG1 = computer,
NWP = network, VID = video, SVD = S-Video
3
000 = power off (standby mode off), 001 = power on (standby mode on)
1
0 = standby, 1 = lamp on under control, 2 = lamp off,
3 = lamp off under control
4
Dicimal without signs: 0000-9999 hours
1
0 = low, 1 = default, 2 = high
8
y1y2y3y4m1m2d1d2w = year (y) month (m) day (d) day of week (w)
Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
6
h1h2m1m2s1s2 = hour (h) minute (m) second (s)
NOTE: If a wrong command is received, the projector will send an ER401 command to the computer.
Command example
To set the volume to +30, send the command as shown below.
STX
Start
AVL
:
Command
30
ETX
Parameter
End
NOTE: When sending commands without parameters, a colon (:) is not necessary.
As of March 2011
SFL11M005-1
13/14
S
P
E
C
F
I
L
E
PT-FW430
LCD Projector
Notes on projector placement and operation
The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the
following precautions.
1.
Never place objects on top of the projector while it is operating.
2.
Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s
exhaust openings. In addition to this space, also ensure that there is a sufficient work space for
removing and installing the lamp, filter and other parts.
3.
Do not stack projector units directly on top of one another for the purpose of multiple (stacked)
projection. When stacking projector units, be sure to provide the amount of space indicated below
between them. These space requirements also apply to installations where only one projector unit is
operating at one time and the other unit is used as a backup.
3.
If the projector is installed in an enclosed space, ensure that the projector’s intake and exhaust
openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is
not sucked into the intake openings.
200 mm (7-7/8˝ ) or more
100 mm
( 3-15/16 ˝ )
or more
500 mm (19-11/16 ˝ )
or more
500 mm (19-11/16 ˝ )
or more
Do not stack projector
units directly on top of
one another.
Direction of air intake and exhaust
Intake
Exhaust
Operating the projector continuously
1.
If the projector is to be operated continuously 10 hours or more, lamp replacement cycle duration
becomes shorter.
2.
The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short
periods (one hour or less).
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
Product availability differs depending on region and country. This product may be subject to export control regulations.
PJLink is a registered trademark, or a trademark application has been filed, in Japan, the United States, and other countries and regions.
Intel, Pentium, and Intel Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Microsoft, Windows Vista and Windows are either registered trademarks or trademarks of Microsoft Corp. in the United States and/or other
countries. Apple, Mac, Mac OS, and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries. PowerPC is a trademark of
International Business Machines Corporation, registered in the U.S.
All other trademarks are the property of their respective trademark owners.
As of March 2011
SFL11M005-1
14/14
TOA Products | BG-1120 Modular Mixer Amplifier
search here !
Home » Products » Amplifiers » BG Series Mixer Power Amplifers » BG-1120
Products Lineup
Audio System
BG-1120 Modular Mixer Amplifier
BG-1120
Amplifiers
Voice Evacuation System
The BG-1120 is a Mixer Power Amplifier and can mix up to a
total of 5 independent input signals. Power output is rated at
120 W, and this is ideal for use in sound systems requiring
small power outputs.
PA Speakers
Pro-Audio Speakers
Wired Microphones
Wireless Microphones
Conference System
Network Audio Adapters
Specification
Intercom System
Megaphones
Mobile Amplifiers
Audio Source Device
(*1) 0 dB = 1 V
Power Source
120 V AC, 60 Hz
Rated Output
120 W
Power Consumption
260 W (rated output), 150 W (based on UL/CSA standards)
Frequency Response
50 - 20,000 Hz
Total Harmonic
Distortion
0.05%, at 1 kHz, rated output
Rack-mount Equipment
Program Timer
Mixers
Audio Signal Processors
Mic: -60 dB (*1), 600 Ω, electrically-balanced, M3 screw terminal
CCTV System
(*2)
PTZ Camera Systems
Fixed Cameras
Lenses for CCTV Cameras
Input
Digital Video Recorders
mixing)
Module: -20 dB (*1), 10 kΩ, unbalanced, card edge connector
Power IN: 0 dB (*1), 10 kΩ unbalance, RCA pin jack
Mute: M3 screw terminal (*2)
Network Camera System
(Netcansee)
Coaxial Multi-Transmission Unit
Camera Accessories
Other Equipment
Data Library
Here, TOA's Data Library equipped
with a search engine offers its CAD
drawings made out in pdf and dwg
forms, EASE data, specification
sheets, brochures, instruction and
installation manuals, and a wealth of
other product data for your
downloading.
Tel: -20 dB (*1), 10 kΩ/600 Ω, balanced, M3 screw terminal (*2)
Program: -10 dB (*1), 10 kΩ, electrically-balanced, M3 screw
terminal (*2)
Aux: -10 dB (*1), 47 kΩ, unbalanced, 2 P RCA pin jack (internal
Output
Main: 4 Ω, 25 and 70 V, balanced, M3 screw terminal (*2)
Sub: 1 W/8 Ω, unbalanced, M3 screw terminal (*2)
MOH: 0 dB(*1), 600 Ω, balanced, M3 screw terminal (*2)
Preamp OUT: 0 dB (*1), 600 Ω unbalance, RCA pin jack
Output Regulation
Under 2 dB, no load to full load
S/N Ratio
Mic: 60 dB, Tel: 75 dB, Program: 75 dB, Aux: 75 dB, Module: 75
dB
(Band Pass: 20 - 20,000 Hz, Tone Controls: Centered)
Bass: ±10 dB at 100 Hz, Treble: ±10 dB at 10 kHz
Tone Controls
Controls affect only program input, aux input and module (BGM)
input
http://www.toa.jp/products/amplifiers/bg-series/bg-1120.html[1/18/2012 8:29:01 AM]
TOA Products | BG-1120 Modular Mixer Amplifier
Cooling Fan Speed
Variable by heat sink temperature
Indicator
Power LED, Signal LED, Peak LED
Protection
Self protection, with 1 AC breaker (outside)
Other Feature
Automatic electronic drive limiter
Output disconnected for approx. 3 seconds after the unit is turned
on
Finish
Panel: ABS resin, black
Case: Steel plate, black, paint
Dimensions
264 (W) × 107.4 (H) × 280 (D) mm
Weight
6.4 kg (without input module)
Accessory
Volume control covers ……5
(*2) Distance between barriers on the above screw terminal: 6 mm
Top of the Page
(C)2008 TOA Corporation. All Rights Reserved.
http://www.toa.jp/products/amplifiers/bg-series/bg-1120.html[1/18/2012 8:29:01 AM]
Site Policy
Toshiba SD-V296 DVD/VCR Player | DVD Players | Video & Electronics | us.Toshiba.com
COMPUTERS
TABLETS
TELEVISIONS
VIDEO & ELECTRONICS
EXPLORE TOSHIBA
Video & Electronics » DVD Players »
More Video & Electronics
Toshiba SD-V296 DVD/VCR Player
MSRP † : $89.99
Average Customer Rating:
Read Reviews (5) | Write Reviews
Available at local retailers
Enter Zip Code
Available at online retailers
May also be available at these dealers
Enter Zip Code
Share
Like Confirm
Print
Specifications
Image Gallery
Customer Reviews
Toshiba SD-V296 Specifications
download detailed spec sheet PDF
More DVD Players
MODEL:
MSRP:
Video
Inputs/Outputs
SD3300
$29.99
MULTI-CAMERA ANGLE SELECT
DIGITAL AUDIO OUT
Yes
1 Coaxial
SD4300
$39.99
MULTI-SUBTITLE SELECT
S-VIDEO
SD7300
$49.99
Yes
Yes
SDP75S
$79.99
RCA VIDEO (COMPOSITE)
SD-V296
$89.99
Audio
JPEG VIEWER *
Yes
DOLBY® DIGITAL
Yes
DOLBY® DIGITAL PLUS
No
DOLBY® TRUE HD
No
SURROUND SOUND*
DTS® Compatible
2 Input, 1 Output
SDP74S
$99.99
1 Output, 2 Input
SDP95S
$129.99
SD CARD (WITH SDHC)
SDP94S
$149.99
RCA AUDIO (L/R ANALOG)
No
ETHERNET PORT
No
USB PORT
No
Features
HDMI® CEC *
No
WI-FI (WIRELESS LAN)
No
BD-LIVE™*
No
REMOTE CONTROL*
Included
BUILT-IN VCR
Yes
ONE TOUCH RECORDING *
Yes
Physical Description
WIDTH
17.14"
http://us.toshiba.com/video-electronics/dvd-players/sd-v296/[1/18/2012 8:06:13 AM]
Toshiba SD-V296 DVD/VCR Player | DVD Players | Video & Electronics | us.Toshiba.com
HEIGHT
3.70"
DEPTH
9.18"
WIDTH (SHIPPING)
21.24"
HEIGHT (SHIPPING)
7.17"
DEPTH (SHIPPING)
13.47"
WEIGHT
5.95 lbs
WEIGHT (SHIPPING)
7.7 lbs
† MSRP:
Reseller/Retailer pricing may vary. Toshiba is not liable for pricing errors.
More Video & Electronics
COMPUTERS »
LAPTOPS
Satellite ®
Tecra ®
Satellite Pro ®
Qosmio®
Portégé ®
HARD DRIVES AND STORAGE
Desktop External Drives
Portable External Drives
DESKTOPS
All-in-One Desktops
TABLETS »
TELEVISIONS »
VIDEO & ELECTRONICS »
EXPLORE TOSHIBA »
Thrive™ Tablet
Tablet Accessories
3D Televisions
LED Televisions
LCD Televisions
TV/DVD Combos
TV Accessories
Blu-ray Players
DVD Players
DVD Recorders
Camcorders
Electronics Accessories
Our History
CONNECT
Contact Us
Social Responsibility
Careers
Ways to Buy
Toshiba Events
Our Commercials
Press Room
Reseller Partners
Public/Private Sector
ACCESSORIES
dynadock ®
Mobile Monitor
See All Accessories
NEED HELP CHOOSING A TV?
TV Finder
TV Research Center
NEED HELP CHOOSING A PC?
Laptop Finder
Computer Research Center
Copyright © 2012 Toshiba America Information Systems, Inc. All rights reserved.
Consumer Notices
Privacy Policy
Terms of Use
http://us.toshiba.com/video-electronics/dvd-players/sd-v296/[1/18/2012 8:06:13 AM]
About Toshiba
Site Map
Press Room
Feedback
Share
VP-4x4K - Fixed I/O - Kramer Electronics
HOME | LOGIN | REGISTER
Product Search
INTERNATIONAL [ change ]
ABOUT KRAMER
PRODUCTS
PRODUCTS
NEWS
MARKETS
TRAINING
SUPPORT
CONTACT US
SWITCHERS & ROUTERS ⁄ Fixed I/O ⁄ Computer (15-Pin HD)
Kramer Matrix™
VP-4x4K
VP-4x4K
4x4 Computer Graphics Video & Balanced Stereo Audio Matrix Switcher
Cables
Sierra
Product Search
QUICK FACTS
What's New
Discontinued
Bandwidth − 400MHz
Delayed Switching
Control − RS−232, RS−485, Ethernet, iPhone® App &
IR
Search
Configurators
Print this page
PDF Datasheet
Click here to enlarge
OVERVIEW
SPECIFICATIONS | APPLICATIONS | DIAGRAM | DOWNLOADS | SUGGESTED CABLES
The VP−4x4K is a high−performance matrix switcher for computer graphics video signals, with resolutions up to and exceeding
UXGA, and balanced stereo audio signals. The unit can route any or all inputs to any or all outputs simultaneously.
High Bandwidth - 400MHz (−3dB).
HDTV Compatible.
Kr-isp® Advanced Sync Processing - Ensures compatibility with a wide range of computers (even if the sync level is too low) by
restoring the sync signal waveform.
Delayed Switching™ - Up to a 3.5s (user selectable) delay for clean switching.
Audio Breakaway Switching.
Memory Locations - Stores multiple switches as presets to be recalled and executed when needed.
ALL/OFF Controls - Sends one input to all outputs, can disconnect all outputs, or turn off individual outputs.
Take Button - Executes multiple switches all at once.
Front Panel Control Lockout.
Active Input Indication™ Reporting - Each input button on the front panel automatically lights when the unit detects a video signal
on that input. When an input is selected for switching, the button changes to a different color to indicate it is the active input.
Input and Output Audio Level Control.
Flexible Control Options - Front panel, RS−485, RS−232 (K−Router™ Windows®−based software is included), Ethernet, iPhone®
App & IR remote (included).
Worldwide Power Supply - 100−240V AC.
Standard 19” Rack Mount Size - 1U. Rack "ears" included.
THIS PRODUCT REPLACES THE VP-4x4 , VP-4x4xl
Contact Us | Subscribe to our newsletter | ISO | Limited Warranty
Copyright © Kramer Electronics LTD. 1981-2012.
http://www.kramerelectronics.com/products/model.asp?pid=1215[1/18/2012 8:25:25 AM]
Middle Atlantic Products - Edit Center - Side Rack Dimensions
Search
S12/D12 Side Rack Dims.
| feature benefits | How to Order | finish | system/desk list info | component list info | dimensions | options |
12 space side bay rack
(dimensions represent single and double bay widths)
| feature benefits | How to Order | finish | system/desk list info | component list info | dimensions | options |
©copyright 2000/ 2012 Middle Atlantic Products, Inc.
http://www.middleatlantic.com/studio/ec/ecsr1.htm[1/18/2012 8:02:31 AM]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising