Installation Instructions

Installation Instructions
Felix Storch, Inc.
Summit Appliance Division
770 Garrison Avenue
Bronx, New York 10474
www.summitappliance.com
Installation Instructions
Over the Range Microwave Oven
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
•
IMPORTANT – Save these instructions for
local inspector’s use.
IMPORTANT – Observe all governing codes
and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions for
future reference.
• Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is not
covered under the Warranty.
READ CAREFULLY. KEEP THESE INSTRUCTIONS.
Installation Instructions
CONTENTS
General information
C
Attach Mounting Plate to Wall ................. 20
Important Safety Instructions .....................3
Preparation of Top Cabinet ..................... 20
Mount the Microwave Oven............... 21, 22
Electrical Requirements ..............................3
Hood Exhaust ...........................................4, 5
Installing the Charcoal Filter .................... 22
Damage – Shipment/Installation .................6
Before You Use Your Microwave ..............23
Parts Included...............................................6
Tools You Will Need .....................................7
Mounting Space............................................7
Step-by-step installation guide
Placement of Mounting Plate ................8–10
Removing the Mounting Plate ................... 8
Finding the Wall Studs .............................. 8
Determining Wall Plate Location ............... 9
Aligning the Wall Plate ............................ 10
Installation Types .................................11–22
A
Outside Top Exhaust .............................. 12–15
Attach Mounting Plate to Wall ................. 12
Preparation of Top Cabinet ..................... 13
Checking for Proper Damper Operation...14
Mount the Microwave Oven..................... 14
Adjust the Exhaust Adaptor..................... 15
Connecting Ductwork .............................. 15
B
Recirculating ........................................... 20–22
Outside Back Exhaust............................. 16–19
Preparing Rear Wall for
.
Outside Back Exhaust. ............................
16
Attach Mounting Plate to Wall ................. 17
Preparation of Top Cabinet ..................... 17
Adapting Microwave Blower for
Outside Back Exhaust ....................... 17, 18
Mount the Microwave Oven..................... 19
2
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
You should have the wall receptacle and circuit
checked by a qualified electrician to make sure
the receptacle is properly grounded.
This product requires a three-prong grounded outlet.
The installer must perform a ground continuity check
on the power outlet box before beginning the
installation to insure that the outlet box is properly
grounded. If not properly grounded, or if the outlet
box does not meet electrical requirements noted
(under ELECTRICAL REQUIREMENTS), a qualified
electrician should be employed to correct any
deficiencies.
Where a standard two-prong wall receptacle is
encountered, it is very important to have it
replaced with a properly grounded three-prong
wall receptacle, installed by a qualified
electrician.
CAUTION: For personal
safety, remove house fuse or
open circuit breaker before
beginning installation to
avoid severe or fatal shock
injury.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT,
DEFORM OR REMOVE ANY OF THE PRONGS
FROM THE POWER CORD. DO NOT USE WITH
AN EXTENSION CORD.
ELECTRICAL REQUIREMENTS
Product rating is 120 volts AC, 60 Hertz, 15 amps and
1.58 kilowatts. This product must be connected to a
supply circuit of the proper voltage and frequency.
Wire size must conform to the requirements of the
National Electrical Code or the prevailing local code
for this kilowatt rating. The power supply cord and
plug should be brought to a separate 20 ampere
branch circuit single grounded outlet. The outlet box
should be located in the cabinet above the
microwave oven. The outlet box and supply circuit
should be installed by a qualified electrician and
conform to the National Electrical Code or the
prevailing local code.
CAUTION: For personal safety, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight of
this 54 pound product, plus additional oven loads
of up to 50 pounds or a total weight of 104
pounds.
CAUTION: For personal safety, this product
cannot be installed in cabinet arrangements such
as an island or a peninsula. It must be mounted to
BOTH a top cabinet AND a wall.
NOTE: For easier installation and personal
safety, it is recommended that two people install
this product.
IMPORTANT–PLEASE READ CAREFULLY. FOR
PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED TO AVOID SEVERE OR
FATAL SHOCK.
Insure
Insure proper
proper
ground
ground exists
exists
before
beforeuse
use
The power cord of this
appliance is equipped
with a three-prong
(grounding) plug which
mates with a standard
three-prong (grounding)
wall receptacle to
minimize the possibility
of electric shock hazard
from this appliance.
3
Installation Instructions
HOOD EXHAUST
NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to
recirculate the air back into the room, proceed to page 6.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.
DUCT PIECES
EQUIVALENT
LENGTH
x
NUMBER
USED
=
EQUIVALENT
LENGTH
24 Ft.
x
(1)
=
24 Ft.
12 Ft. Straight Duct (6" 12 Ft.
Round)
x
(1)
=
12 Ft.
Rectangular-to-Round 5 Ft.
Transition Adaptor*
x
(1)
=
5 Ft.
=
41 Ft.
Roof Cap
Equivalent lengths of duct pieces are based on actual
tests and reflect requirements for good venting
performance with any vent hood.
Total Length
* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have
to be cut to fit, using the tin snips, in order to allow free movement of the damper.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.
DUCT PIECES
EQUIVALENT
LENGTH*
x
NUMBER
USED
=
EQUIVALENT
LENGTH
Roof Cap
40 Ft.
x
(1)
=
40 Ft.
3 Ft. Straight Duct
(3¼" x 10"
Rectangular)
3 Ft.
x
(1)
=
3 Ft.
90° Elbow
10 Ft.
x
(2)
=
20 Ft.
=
63 Ft.
Equivalent lengths of duct pieces are based on actual
tests and reflect requirements for good venting
performance with any vent hood.
Total Length
NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be
prepared at the time it is constructed by leaving enough space between the wall studs to accommodate
exhaust.
4
Installation Instructions
Maximum duct length:
NOTE: If you need to install ducts, note that the total
duct length of 3¼" x 10" rectangular or 6" diameter
round duct should not exceed 140 equivalent feet.
Outside ventilation requires a HOOD EXHAUST
DUCT. Read the following carefully.
NOTE: It is important that venting be installed using
the most direct route and with as few elbows as
possible. This ensures clear venting of exhaust and
helps prevent blockages. Also, make sure dampers
swing freely and nothing is blocking the ducts.
For satisfactory air movement, the total duct length of
3¼" x 10" rectangular or 6" diameter round duct
should not exceed 140 equivalent feet.
Elbows, transitions, wall and roof
caps, etc., present additional resistance to
airflow and are equivalent to a section of straight duct
which is longer than their actual physical size. When
calculating the total duct length, add the equivalent
lengths of all transitions and adaptors plus the length
of all straight duct sections. The chart below shows
you how to calculate total equivalent ductwork length
using the approximate feet of equivalent length of
some typical ducts.
Exhaust connection:
The hood exhaust has been designed to mate with a
standard 3¼" x 10" rectangular duct.
If a round duct is required, a rectangular-to-round
transition adaptor must be used. Do not use less
than a 6" diameter duct.
DUCT PIECES
EQUIVALENT
LENGTH
x
NUMBER
USED
=
Rectangular-to-Round
Transition Adaptor*
5 Ft.
x
( )
=
Ft.
Wall Cap
40 Ft.
x
( )
=
Ft.
90° Elbow
10 Ft.
x
( )
=
Ft.
45° Elbow
5 Ft.
x
( )
=
Ft.
90° Elbow
25 Ft.
x
( )
=
Ft.
45° Elbow
5 Ft.
x
( )
=
Ft.
Roof Cap
24 Ft.
x
( )
=
Ft.
Straight Duct 6" Round or
3¼" x 10" Rectangular
1 Ft.
x
( )
=
Ft.
Total Ductwork
=
Ft.
* IMPORTANT: If a rectangular-toround transition adaptor is used, the
bottom corners of the damper will
have to be cut to fit, using the tin
EQUIVALENT
LENGTH
snips, in order to allow free movement of the damper.
Equivalent lengths of duct pieces are based on actual
tests and reflect requirements for good venting
performance with any vent hood.
5
Installation Instructions
DAMAGE – SHIPMENT/
INSTALLATION
PARTS INCLUDED
HARDWARE PACKET
• If the unit is damaged in shipment, return the
unit to the store in which it was bought for repair
or replacement.
• If the unit is damaged by the customer, repair
or replacement is the responsibility of the
customer.
• If the unit is damaged by the installer (if other
than the customer), repair or replacement must
be made by arrangement between customer and
installer.
PART
QUANTITY
Wood Screws
(1/8" x 3/4")
6
Toggle Bolts
(and wing nuts)
(3/16" x 3")
3
Self-aligning
Machine Screws
(¼"-28 x 3¼")
3
Nylon Grommet
2
(for metal cabinets)
PARTS INCLUDED
Wire-Mounting
2
You will find the installation hardware contained in a
packet with the unit. Check to make sure you have all
these parts.
NOTE: Some extra parts are included.
Mounting-Plate
1
ADDITIONAL PARTS
shelf
1
exhaust adaptor
1
PART
QUANTITY
PART
QUANTITY
TOP CABINET TEMPLATE
REAR WALL TEMPLATE
Installation
Instructions
Top
Cabinet
Template
1
Rear Wall
Template
1
Installation
Instructions
1
Separately
Packed
Grease
Filters
2
Charcoal
Filter
6
1
Installation Instructions
TOOLS YOU WILL NEED
Ruler or tape measure
and straight edge
Pencil
# 1 and #2 Phillips screwdriver
Tin snips (for cutting
damper, if required)
Scissors
(to cut template, if necessary)
Gloves
Saw (saber, hole or keyhole)
Safety goggles
Electric drill with 3/16", ½"
and 5/8" drill bits
Duct and masking tape
MOUNTING SPACE
30"
2"
30"min.
Filler blocks or scrap wood
pieces, if needed for top
cabinet spacing (used on
recessed bottom cabinet
installations only)
Stud finder or Hammer (optional)
Level
16-½ "
Carpenter square
(optional)
Bottom edge of
cabinet needs
to be 30" or
more from the
cooking
surface
Backsplash
66" or more
from the floor
to the top of the
microwave
7
NOTES:
• The space between the cabinets must be
30" wide and free of obstructions.
• If the space between the cabinets is greater
than 30", a Filler Panel Kit may be used to fill
in the gap between the microwave oven and
the cabinets. Your Owner’s Manual contains
the kit number for your model.
• This microwave oven is for installation over
ranges up to 36" wide.
• If you are going to vent your microwave oven
to the outside, see Hood Exhaust Section for
exhaust duct preparation.
• When installing the microwave oven
beneath smooth, flat cabinets, be careful
to follow the instructions on the top
cabinet template for power cord
clearance.
Installation Instructions
1. PLACEMENT OF THE MOUNTING PLATE
A. REMOVING THE MICROWAVE
B. FINDING THE WALL STUDS
OVEN FROM THE CARTON/
ASSEMBLE THE MOUNTING
PLATE
1. Remove the installation instructions, filters, glass
tray and the small hardware bag. Do not remove
the Styrofoam protecting the front of the oven.
Wall Studs
2. Fold back all 4 carton flaps fully against carton
Center
sides. Then carefully roll the oven and carton over
onto the top side. The oven should be resting in
the Styrofoam.
Carton
1. Find the studs, using one of the following
methods:
A. Stud finder–a magnetic device which locates
nails.
OR
Styrofoam
B. Use a hammer to tap lightly across the
mounting surface to find a solid sound. This
will indicate a stud location.
3. Pull the carton up and off the oven.
4. Remove and properly discard plastic bags.
5. you will be able to assemble it take following
2. After locating the stud(s), find the center by
probing the wall with a small nail to find the edges
of the stud. Then place a mark halfway between
the edges. The center of any adjacent studs
should be 16" or 24" from this mark.
picture.
3. Draw a line down the center of the studs.
Wire-Mounting
THE MICROWAVE MUST BE CONNECTED TO AT
LEAST ONE WALL STUD.
Mounting-Plate
8
Installation Instructions
C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Plate position – beneath framed recessed
cabinet bottom
Plate position – beneath flat bottom cabinet
Mounting Plate Tabs
Touching the Cabinet Bottom
Mounting Plate Tabs
Touching the Back
Frame
30" to Cooktop
At le ast 30"
Your cabinets may have decorative trim that
interferes with the microwave installation. Remove
the decorative trim to install the microwave properly
and to make it level.
Plate position – beneath recessed bottom
cabinet with front overhang
Mounting Plate with
Tabs Below Cabinet
Bottom the Same
Distance as the Front
Overhang Depth
THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a front overhang only, with no
back or side frame, install the mounting plate down
the same distance as the front overhang depth. This
will keep the microwave level.
1. Measure the inside depth of the front overhang.
2. Draw a horizontal line on the back wall an equal
distance below the cabinet bottom as the inside
depth of the front overhang.
30" to Cooktop
3. For this type of installation with front overhang
only, align the mounting tabs with this horizontal
line, not touching the cabinet bottom as described
in Step D.
9
Installation Instructions
D. ALIGNING THE WALL PLATE
Hole A
Area E
Centerline
notches
Hole C
Draw a Vertical
Line on Wall
from Center of
Top Cabinet
Hole B
CAUTION: Wear gloves to avoid
cutting fingers on sharp edges.
1. Draw a vertical line on the wall at the center of the
NOTE: Holes A,B and C are inside area E. If none of
A,B and c is in a stud, find a stud somewhere in area
E and draw a fo circle to line up with the stud. It is
important to use at least one wood screw mounted
firmly in a stud to support the weight of the
microwave. Set the mounting plate aside.
30" wide space.
2. Use the mounting plate as the template for the
rear wall. Place the mounting plate on the wall,
making sure that the tabs are touching the
bottom of the cabinet or the level line drawn in
Step C for cabinets with front overhang. Line
up the notch and center line on the bottom of
the mounting plate to the center line on the
wall.
4. Drill holes on the circles.
If there is a stud, drill a 3/16" hole for wood screws.
Three holes that don’t line up with a stud, drill 5/8"
a hole for toggle bolts.
NOTE: DO NOT MOUNT THE PLATE AT THIS
TIME.
3. While holding the mounting plate with one hand,
draw circles on the wall at holes A, B and C
(see illustration above/actual plate marked with
arrows). Four holes must be used for
mounting.
10
Installation Instructions
2. INSTALLATION TYPES (Choose A, B or C)
NOTE: This microwave is shipped assembled for
Recirculating.
This microwave oven is designed for adaptation to
the following three types of ventilation:
A. Outside Top Exhaust (Vertical Duct)
B. Outside Back Exhaust (Horizontal Duct)
C. Recirculating (Non-Vented Ductless)
A. OUTSIDE TOP EXHAUST
B. OUTSIDE BACK EXHAUST
(VERTICAL DUCT)
(HORIZONTAL DUCT)
Adaptor in Place for
Outside Top
Exhaust
See page 12
See page 16
C. RECIRCULATING
(NON-VENTED DUCTLESS)
A Charcoal Filter
Accessory Kit is required
for the non-vented exhaust.
(See your Owner’s Manual
for the kit number.)
See page 20
11
Installation Instructions
A. OUTSIDE TOP EXHAUST (Vertical Duct)
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3. Check Microwave Assembly
A4. Check Damper Operation
A5. Mount Microwave Oven
A6. Adjust Exhaust Adaptor
A7. Connect Ductwork
A1. ATTACH THE MOUNTING PLATE
To use toggle bolts:
TO THE WALL
Spacing for Toggles More
Than Wall Thickness
Mounting
Plate
Toggle Wings
Toggle
Bolt
Wall
Bolt End
3. Place the mounting plate against the wall and
Attach the plate to the wall using toggle bolts. At least
one wood screw must be used to attach
the plate to a wall stud.
insert the toggle wings into the holes in the wall to
mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the tabs on the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly centered
under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
1. Remove the toggle wings from the bolts.
2. Insert the bolts into the mounting plate through the
holes designated to go into drywall and reattach
the toggle wings to ¾" onto each bolt.
4. Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
12
Installation Instructions
A2. USE TOP CABINET TEMPLATE
3. Roll the blower unit 90° so that fan blade
FOR PREPARATION OF TOP
CABINET
openings are facing out the up of the
microwave.
After Rolling
Before Rolling
You need to drill holes for the top support screws, a
hole large enough for the power cord to fit through,
and a cutout large enough for the exhaust adaptor.
4
Back of
Microwave
Back of
Microwave
Place the blower unit back into the opening.
AFTER: Fan Blade
Openings Facing UP
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes
in the cabinet bottom.
CAUTION: Do not pull or stretch the blower unit
wiring. Make sure the wires are not
pinched.
NOTE: The blower unit exhaust openings should
match exhaust openings on rear of microwave
oven.
A3. ADAPTING MICROWAVE BLOWER
FOR RECIRCULATION
5
1. Remove and save
screw that holds
blower plate to
microwave. Screw
Secure the blower
. unit to the microwave with the
screw from Step 1.
Blower Plate
Back of
Microwave
Blower Motor
Screw
Back of Microwave
2
6. Replace the blower plate in the same position as
before with the screw.
Screw
Carefully pull out the blower unit. The wires will
extend far enough to allow you to adjust the
blower unit.
13
Installation Instructions
A5. MOUNT THE MICROWAVE OVEN
A4. CHECK FOR PROPER DAMPER
OPERATION
Blower Plate
Exhaust Adaptor
(absent on models
shipped for recirculation
exhaust)
Damper
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during
installation.
NOTE: If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case
damage may occur from over tightening screws.
Back of
Microwave
• Place the microwave in its upright position, with
the top of the unit facing up.
• This microwave oven may be shipped assembled
for top exhaust (adaptor installed) or for
recirculation exhaust (adaptor absent).
• Make sure tape securing damper is removed
and damper pivots easily before mounting
microwave.
• You will need to make adjustments to assure
proper alignment with your house exhaust duct
after the microwave is installed.
NOTE: When mounting the microwave oven, thread
power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1–3. Do not pinch cord
or lift oven by pulling cord.
1. Lift microwave, tilt it
forward, and hook slots
at back bottom edge
onto four lower tabs of
mounting plate.
2. Rotate front of oven
up against cabinet
bottom
3. Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least two full turns after the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord,
especially when mounting flush to bottom of
cabinet.
14
Installation Instructions
A5. MOUNT THE MICROWAVE OVEN
A6. ADJUST THE EXHAUST ADAPTOR
(cont.)
Open the top cabinet and adjust the exhaust adaptor
to connect to the house duct.
Cabinet Front
Cabinet Bottom Shelf
Filler Block
Blower Plate
Back of
Microwave
Damper
Equivalent to
Depth of Cabinet
Recess
For Front-to-Back or
Side-to-Side Adjustment,
Slide the Exhaust
Adaptor as Needed
Self-Aligning Screw
Microwave Oven Top
4. Attach the microwave oven to the top cabinet.
5. Insert 2 self-aligning screws
A7. CONNECTING DUCTWORK
through outer top cabinet holes.
Turn two full turns on each screw.
House Duct
6. Tighten center screw
completely.
7. Tighten the outer two screws to the top of the
1. Extend the house duct down to connect to the
microwave oven. (While tightening screws, hold
the microwave oven in place against the wall and
the top cabinet.)
exhaust adaptor.
2. Seal exhaust duct joints using duct tape.
8. Install grease filters. See the Owner’s Manual
packed with the microwave.
15
Installation Instructions
B. OUTSIDE BACK EXHAUST (Horizontal Duct)
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Attach Mounting Plate to Wall
B3. Prepare Top Cabinet
B4. Adjust Blower
B5. Mount the Microwave Oven
B1. PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for outside
exhaust.
• Read the instructions on the REAR WALL
TEMPLATE.
• Tape it to the rear wall, lining up with the holes
previously drilled for holes A and B in the wall
plate.
• Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
16
Installation Instructions
B2. ATTACH THE MOUNTING PLATE
B3. USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
Attach the plate to the wall using toggle bolts. At least
one wood screw must be used to attach
the plate to a wall stud.
1. Remove the toggle wings from the bolts.
2. Insert the bolts into the mounting plate through
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes
in the cabinet bottom.
the holes designated to go into drywall and
reattach the toggle wings to ¾ " onto each bolt.
To use toggle bolts:
Spacing for Toggles More
Than Wall Thickness
Mounting
Plate
B4. ADAPTING MICROWAVE BLOWER
Toggle Wings
Toggle
Bolt
FOR OUTSIDE BACK EXHAUST
1. Remove and save screw that holds blower motor
to microwave,Lift up the blower plate.
Wall
Bolt End
screw
Blower Motor
3. Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall to
mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the tabs on the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Back of
Microwave
Blower Motor
Screw
2. Carefully pull out the blower unit. The wires will
extend far enough to allow you to adjust the
blower unit.
BEFORE: Fan Blade
Openings Facing Front
4. Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
17
Installation Instructions
B4 ADAPTING MICROWAVE BLOWER
5. Place the blower unit back into the opening.
FOR OUTSIDE BACK EXHAUST
(cont.)
AFTER
: Fan Blade
Openings Facing Back
Openings Facing Back
3. Remove “Parts A”with Nipper or Scissors.
End A
End B
Part”A”
CAUTION: Do not pull or stretch the blower unit
wiring. Make sure the wires are not
pinched.
NOTE: The blower unit exhaust openings should
match exhaust openings on rear of microwave
oven.
4. Rotate blower unit counterclockwise 180°.
Before Rotation
After Rotation
6. Secure the blower unit to the microwave with the
Back of
Microwave
screw from Step 1.
Back of
Microwave
Blower Plate
Back of
Microwave
Blower Motor
Screw
7. Replace the blower plate in the same position as
before with the screw.
8.
Attach the exhaust adaptor to the rear of the oven
by sliding it into the guides at the top center of the
back of the oven.
Adaptor
Back of
Microwave
Guide
Guide
Locking Tabs
Push in securely until it is in the lower locking tabs.
Take care to assure that the damper hinge is installed
so that it is at the top and that the damper swings
freely.
18
Installation Instructions
B5. MOUNT THE MICROWAVE OVEN
Cabinet Front
Cabinet Bottom Shelf
Filler Block
Equivalent to
Depth of Cabinet
Recess
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during
installation.
NOTE: If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case
damage may occur from over tightening screws.
Self-Aligning Screw
Microwave Oven Top
4. Attach the microwave oven to the top cabinet.
5. Insert 2 self-aligning screws
through outer top cabinet holes.
Turn two full turns on each screw.
NOTE: When mounting the microwave oven, thread
power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1–3. Do not pinch cord
or lift oven by pulling cord.
1. Lift microwave, tilt it
forward, and hook slots
at back bottom edge
onto four lower tabs of
mounting plate.
6. Tighten center
screw completely.
7. Tighten the outer two screws to the top of the
microwave oven. (While tightening screws, hold
the microwave oven in place against the wall and
the top cabinet.)
2. Rotate front of oven
up against cabinet
bottom
3. Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least two full turns after the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord,
especially when mounting flush to bottom of
cabinet.
8. Install grease filters. See the Owner’s Manual
packed with the microwave.
19
Installation Instructions
C. RECIRCULATING (Non-Vented Ductless)
INSTALLATION OVERVIEW
C1. Attach Mounting Plate to Wall
C2. Prepare Top Cabinet
C3. Mount the Microwave Oven
C4. Install Charcoal Filter
C1. ATTACH THE MOUNTING PLATE
3. Place the mounting plate against the wall and
TO THE WALL
insert the toggle wings into the holes in the wall to
mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the tabs on the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
4. Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
C2. USE TOP CABINET TEMPLATE
Attach the plate to the wall using toggle bolts. At least
one wood screw must be used to attach the plate to
a wall stud.
FOR PREPARATION OF TOP
CABINET
1. Remove the toggle wings from the bolts.
2. Insert the bolts into the mounting plate through
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
the holes designated to go into drywall and
reattach the toggle wings to ¾ " onto each bolt.
To use toggle bolts:
Spacing for Toggles More
Than Wall Thickness
Mounting
Plate
Toggle Wings
Toggle
Bolt
Wall
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes
in the cabinet bottom.
Bolt End
20
Installation Instructions
C3. MOUNT THE MICROWAVE OVEN
NOTE: When mounting the microwave oven, thread
power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1–3. Do not pinch cord
or lift oven by pulling cord.
1. Lift microwave, tilt it
forward, and hook slots
at back bottom edge
onto four lower tabs of
mounting plate.
FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle during
installation.
NOTE: If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case
damage may occur from over tightening screws.
2. Rotate front of oven
up against cabinet
bottom
3. Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least two full turns after the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord,
especially when mounting flush to bottom of
cabinet.
Cabinet Front
Cabinet Bottom Shelf
Filler Block
Equivalent to
Depth of
Cabinet Recess
Self-Aligning Screw
Microwave Oven Top
4. Attach the microwave oven to the top cabinet.
21
Installation Instructions
C3 MOUNT THE MICROWAVE OVEN
C4. INSTALLING THE CHARCOAL
(cont.)
FILTER
5. Insert 2 self-aligning screws
1. Remove screws on top of grille using a #1 Phillips
through outer top cabinet holes.
Turn two full turns on each screw.
screwdriver.
2. Open the door.
3. Remove the grille.
• Pull the grille straight off.
Charcoal
Filter
6. Tighten center
screw completely.
7. Tighten the outer two screws to the top of the
microwave oven. (While tightening screws, hold
the microwave oven in place against the wall and
the top cabinet.)
4. Install the charcoal filter. When properly installed,
the wire mesh of the filter should be visible from
the front.
5. Replace the grille and the screws.
6. Close the door.
MO14XX Series Models
MO16XX Series Models
8. Install grease filters. See the Owner’s Manual
packed with the microwave.
Insert mesh-side down
22
Insert mesh-side up
Installation Instructions
BEFORE YOU USE YOUR MICROWAVE
1. Make sure the microwave oven has been installed
6. Read the Owner’s Manual.
according to instructions.
2. Remove all packing material from the microwave
7. KEEP INSTALLATION INSTRUCTIONS FOR
oven.
THE LOCAL INSPECTOR’S USE.
3. Install turntable and ring in cavity.
4. Replace house fuse or turn breaker back on.
5. Plug power cord into a dedicated 20 amp
electrical outlet.
Insure proper
ground exists
before use
23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising