TOLL FREE: 1-866-390-1303
TABLE OF CONTENTS
FCC RADIATION NORM: ................................................................................................................................................. 4
PACKAGE CONTENTS: ................................................................................................................................................... 5
SYSTEM REQUIREMENTS: ............................................................................................................................................ 5
SAFETY INSTRUCTION:.................................................................................................................................................. 6
CHAPTER 1: DVR FEATURES ........................................................................................................................................ 7
CHAPTER 2: INSTALLING HARD DISK DRIVE .............................................................................................................. 8
CHAPTER 3: LAYOUT.................................................................................................................................................... 10
3.1 FRONT PANEL (PLEASE REFER TO ACTUAL PRODUCT FOR DETAIL) ............................................................................. 10
3.2 REAR PANEL (PLEASE SEE ACTUAL PRODUCT FOR DETAIL) ........................................................................................ 11
3.3 REMOTE CONTROL .................................................................................................................................................. 12
3.4 MOUSE OPERATION................................................................................................................................................. 13
CHAPTER 4: DVR/CAMERA INSTALLATION ............................................................................................................... 14
4.1 CONNECTING THE DVR TO A TV OR MONITOR .......................................................................................................... 14
4.2 CONNECTING THE POWER SUPPLY ........................................................................................................................... 14
4.3 CONNECTING THE CAMERAS .................................................................................................................................... 14
CHAPTER 5: DVR START UP........................................................................................................................................ 15
5.1 SYSTEM INITIALIZATION ............................................................................................................................................ 15
5.2 MAIN INTERFACE ..................................................................................................................................................... 15
CHAPTER 6: DVR MENU AND OPTIONS..................................................................................................................... 16
6.1 MAIN MENU PREVIEW .............................................................................................................................................. 17
6.2 MAIN MENU ............................................................................................................................................................ 18
6.2.1 Camera setup ................................................................................................................................................ 18
6.2.2 Playback ........................................................................................................................................................ 19
6.2.3 Backup........................................................................................................................................................... 20
6.2.4 Backup File Data ........................................................................................................................................... 20
6.2.5 Converting Files to AVI:................................................................................................................................. 20
6.2.6 Record setup ................................................................................................................................................. 21
6.2.7 Network Setup – Intranet (Internal Access) .................................................................................................. 22
6.2.8 Network Setup – Global Access (Connected Directly to Modem)................................................................. 23
6.2.9 Network Setup – Global Access (Connected through a Router or Firewall)................................................. 24
6.2.10 Basic Setup ................................................................................................................................................. 28
6.2.10.1 Language .............................................................................................................................................................. 28
6.2.10.2 Time Set................................................................................................................................................................ 28
6.2.10.3 Password .............................................................................................................................................................. 29
6.2.10.4 Video Setup........................................................................................................................................................... 29
6.2.11 Advanced Setup .......................................................................................................................................... 29
6.2.11.1 Alarm Setup .......................................................................................................................................................... 30
User’s Manual
6.2.11.2 System Information ............................................................................................................................................... 30
6.2.11.3 Motion Detect ........................................................................................................................................................ 31
6.2.11.4 Mobile Phone Access............................................................................................................................................ 31
6.2.11.5 System Maintenance............................................................................................................................................. 35
6.2.11.6 PTZ Setup ............................................................................................................................................................. 35
6.2.11.7 HDD Management ................................................................................................................................................ 36
6.3 KEYLOCK ............................................................................................................................................................. 37
6.4 CHANNEL SWITCH.............................................................................................................................................. 37
6.5 VIDEO SEARCH ....................................................................................................................................................... 37
6.6 PTZ CONTROL ........................................................................................................................................................ 37
6.7 MANUAL REC....................................................................................................................................................... 37
6.8 STOP RECORDING ................................................................................................................................................... 37
CHAPTER 7: NET-VIEWER PROGRAM........................................................................................................................ 38
7.1 LOG-IN TO NET-VIEWER........................................................................................................................................... 38
7.2 MAIN INTERFACE OF NET-VIEWER ............................................................................................................................ 39
7.2.1 Menu column ................................................................................................................................................. 39
7.2.1.1 Live ......................................................................................................................................................................... 39
7.2.1.2 Playback.................................................................................................................................................................. 39
7.2.1.3. Setup...................................................................................................................................................................... 40
7.2.1.4 Exit .......................................................................................................................................................................... 41
7.2.2 PTZ Control ................................................................................................................................................... 42
7.2.3 Live Play Control ........................................................................................................................................... 42
7.2.4 Remote Backup ............................................................................................................................................. 43
7.2.5 Multi Player File format.................................................................................................................................. 43
3
User’s Manual
FCC RADIATION NORM:
FCC
This equipment has been tested and found to comply with limits for Class B digital device pursuant
to Part 15 of Federal Communications Commission (FCC) rules.
FCC Compliance Statement
These limits are designed to provide reasonable protection against frequency interference in
residential installation. This equipment generates, uses, and can radiate radio frequency energy,
and if not installed or used in accordance with the instructions, may cause harmful interference to
radio communication. However, there is no guarantee that interference will not occur in television
reception, which can be determined by turning the equipment off and on. The user is encouraged to
try and correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and the receiver

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected to.
CAUTION!
The Federal Communications Commission warns the user that changes or modifications to the unit
not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
4
User’s Manual
PACKAGE CONTENTS:
Your new Security DVR will ship with the following items.
SYSTEM REQUIREMENTS:
Please be sure the computer that you install the included software with complies with the following
specifications:
-
IBM PCs or 100% Compatibles
-
Windows® XP, Vista, 7
-
Internet Explorer 7 or Newer Web Browser Software
-
CD-ROM Drive (for software installation)
5
User’s Manual
SAFETY INSTRUCTION:
1. Use proper power source.
Do not use this product with a power source that applies more than specified voltage
(100-240V AC).
2. Never insert any metal into the DVR or any openings.
Putting metal into the DVR case can cause danger of electric shock.
3. Do not operate in wet or dusty area.
Avoid places like a damp basement or dusty hallway.
4. Do not expose this product to rain or use near water.
If this product accidentally gets wet, unplug it and contact technical support immediately.
5. Keep product surfaces clean and dry.
To clean the outside case of the DVR, use a lightly dampened cloth (no solvents). Do not
use any cleaning solutions or cleaner.
6. Provide proper ventilation.
Use in well ventilated area to avoid overheating of the device.
7. Do not attempt to remove the top cover.
If any abnormal operation is observed, unplug it immediately and contact technical support.
8. Do not attempt to remove the top cover.
Warning: You may be subjected to severe electrical shock if you remove the cover of the
DVR.
9. Handle DVR box carefully.
If you accidentally drop your DVR on any hard surface, it may cause a malfunction. If the
DVR doesn’t work properly due to physical damage, contact an authorized dealer for repair
or exchange.
10. Recommended to use with UPS (Uninterruptable Power Supply)
Connecting your DVR and cameras to a UPS allows continue operation even during power
outages. The duration of power out usage time depends on types of UPS used.
11. Make sure there is good air circulation around the unit.
This DVR system uses a hard drive for video storage, which generates heat during
operation. Do not block air holes/vents (bottom, upper, sides and back) of the DVR that
reduce the generated heat while the system is running. Install or place this product in a well
ventilated area.
6
User’s Manual
CHAPTER 1: DVR FEATURES
Other Features:
•
•
•
•
•
•
•
•
•
H.264 compression
Real time recording on 8 channels
USB Backup to flash drive
Triplex operation: view, record, playback simultaneously
Security Certified Hard Drive pre-installed
Easy control with USB mouse
Instant viewing using Windows® Mobile™, Symbian® S60 Version 3 or 5 and iPhone®
Internet Remote Functions*: View, Search & Playback, Backup and Setup
Email alerts with JPEG attachment
7
User’s Manual
CHAPTER 2: INSTALLING HARD DISK DRIVE
If you have purchased a Digital Video Recorder (DVR) with pre-installed Hard Disk Drive (HDD),
please skip to Chapter 3. Opening DVRs with pre-installed HDD will void the warranty. To install
Hard Disk Drive to the DVR, please follow the instruction below:
1. Remove the 5 case screws located on the back and two sides of the DVR.
8
User’s Manual
2. Locate the SATA Power and Data cable in your DVR.
3. Connect the SATA Power and Data cable to the back of your Hard Disk Drive.
4. Mount the Hard Disk to your DVR using the included mounting screws.
5. Place the DVR cover back onto the DVR.
6. Use the 5 case screws removed from step 1 to mount the DVR Case to the DVR.
WARNING: The DVR case must be secured to the DVR using all 5 mounting screws. Operating
the DVR without the cover is extremely dangerous. It may cause severe injury and will void the
warranty.
7. Once your Hard Disk is installed successfully, please go to section 6.2.10.1 (HDD Management)
of this manual to format the Hard Disk. The Hard Disk must be formatted before it can be used.
9
User’s Manual
CHAPTER 3: LAYOUT
3.1 Front Panel (Please refer to actual product for detail)
Item Indicators
Marks
Functions
1
Power LED
PWR
Lights up when DVR is properly powered and running
2
Link LED
LINK
Lights up when Ethernet is working properly
3
Hard Disk LED
HDD
Lights up when Hard Disk is being accessed
4
Recording LED
REC
Lights up when DVR is recording
10
User’s Manual
3.2 Rear Panel (Please see actual product for detail)
1
3
7
2
5
6
4
Item
Physical
ports
Connection method
1
Video inputs
Connect CH1-8 ( BNC interface)
2
Video output
Connect monitor output ( BNC interface)
3
USB Mouse
Connect USB mouse
4
USB Backup
Connect USB device (Flash Drive, Hard Drive)
5
Ethernet Port
Connect intranet, internet (RJ45 interface)
6
PTZ
Outputs for connecting Pan Tilt Zoom enabled camera
7
Power Port
Connect power supply - DC12V 3A
11
User’s Manual
3.3 Remote Control
The remote control is the secondary input device for navigating the system’s interface.
To use the remote control:
Press to disable audio of the DVR
1-4
5-9 & 0
PTZ
Channel Select 1-4
Digital Key 5-9, 0
Move to PTZ (Pan Tilt Zoom) control mode
Press to switch quad and individual channel display on
screen
Press to navigate in menus and select options.
Press to select an option or enter into a sub menu
Press to exit menu or go back to previous menu.
Press to open the menu
Start Manual recording
Stop Manual Recording
Play
Pause / Playback
Rewind
Forward
Slow Motion / Frame by Frame
F1
Function Button 1
F2
Function Button 1
12
User’s Manual
3.4 Mouse Operation
You can use a mouse instead of the front panel buttons or remote control to navigate the
operation of your DVR
The mouse is the primary input device for navigating system menus.
To use a mouse with the system:
1. Connect a USB mouse to the Top USB MOUSE port on back panel of the system.
NOTE: Only the bottom USB port on the back panel is designed for data backup to a
USB flash drive. Do not connect a USB flash drive to the top USB port on the rear panel.
2. Use the mouse buttons to perform the following:
a. Left-Button: Click to select a menu option; during live viewing in split-screen,
double-click on a channel to view the selected channel in full-screen; double-click
the channel again to return to split-screen view
b. Right-Button: Click to open the Sub-Menu
3. Scroll-Wheel: No function
13
User’s Manual
Chapter 4: DVR/Camera installation
4.1 Connecting the DVR to a TV or Monitor
Using the supplied BNC to RCA connector
1. Connect the BNC to RCA connector to the back of the DVR labeled Video Output (refer to
Chapter 2.2, Rear Panel Picture)
2. Connect the other end of the cable to an open RCA VIDEO input on your TV or Monitor
3. Select the appropriate video input on your TV or Monitor to view the DVR
NOTE: Your DVR must be powered on so you can view on your TV or Monitor.
4.2 Connecting the Power Supply
1. Plug the provided power supply into the back of the DVR labeled “DC12V”
2. Plug the other end of the power Adapter into any 110V outlet within your home or business.
NOTE: Connecting your DVR and Cameras power source into a UPS or battery backup system will
provide you recorded coverage after power failures. Time depends on type of UPS used.
NOTE: Ensure the cable is pushed all the way into the power supply. Otherwise the DVR will not
power on!!
4.3 Connecting the Cameras
NOTE: Prior to mounting the cameras to their desired destination, please ensure all cameras are
working. Perform these steps near the DVR. Once all cameras are up and running, then you can lay
the cables and mount the cameras to their desired location.
1. Each camera comes with 60ft. of cable per camera. Using one cable per camera, plug each
BNC connector of the camera into the 60ft cable.
2. Plug the other end of the cables into the back of the DVR labeled “CH1, CH2, CH3 … CH8”.
3. Connect the provided power splitter to the DC jacks of the cameras, and plug the power
splitter into the camera adapter, then plug the camera adapter to any 110V outlet or UPS.
14
User’s Manual
CHAPTER 5: DVR START UP
5.1 System Initialization
After connecting the power adapter and turning on the power, the system will boot-up and start
initializing.
5.2 Main Interface
After initialization, the main interface will load. When there are
video inputs, the interface will display live images from the
cameras. In the main interface, if you use the mouse to
double-click the live image of any channel, the image will be
maximized to full screen, by double-clicking again, the display
will return to quad mode displaying all cameras; clicking the
right button of the mouse, will load the Pop-up Menu; by
clicking the left button of the mouse to select options; when
clicking any area outside the menu, you will close the Pop-up
menu.
USING THE ONSCREEN DISPLAY
Use the system’s graphical onscreen display to navigate menus and configure options and
settings.
1. Date & Time: Displays the date and time on the system
2. Channel Title: Displays the customizable name for the channel.
3. Record Status: Displays the current recording status of the system: R=recording); M=motion
recording; A=alarm recording; H= HDD problem Channel number: Displays channel number.
NOTE: By default, passwords are disabled on the system. You do not need to enter a
password when accessing any system menus. However, for security purposes, it is highly
recommended to enable passwords on the system using the Password Menu.
For details, see “Managing Passwords”
15
User’s Manual
CHAPTER 6: DVR MENU AND OPTIONS
Mouse Only
When using the mouse, use the Sub-Menu to access several system options, including the
Main Menu.
To open the Sub-Menu:
Right-click anywhere onscreen to open Sub-Menu.
Select one of the following options:
1. MAIN MENU: Opens the main system menu
2. KEYLOCK: If you have password enabled, select this to
activate password protection
3. CHN SWITCH: Choose between Quad Screen, or display
any single channel of the inputs
4. VIDEO SEARCH: Open the Search Menu to view
recorded video
5. PTZ: Opens the PTZ control menu
6. MANUAL REC: Start manual recording
7. STOP REC: Stop manual recording
To close the Sub-Menu, click anywhere onscreen.
Using the Virtual Keyboard – Mouse Only
When using the mouse, you can input certain values using the onscreen virtual keyboard.
You will need to use the Virtual Keyboard when entering your User ID and Password.
To use the Virtual Keyboard:
1. Click on an option or field, such as the User ID and Password
fields.
2. Click 0~9 to enter the desired digit.
to switch between numerals, upper and
3. Click
lowercase letters, and other characters (only for certain
options)
to Backspace/Delete.
4. Click
NOTE: The buttons will turn from orange to white when you
select the button with the mouse cursor.
5. Click
16
to enter/confirm and close the Virtual Keyboard.
User’s Manual
6.1 Main Menu Preview
Cameras
Color Setup
Search
Playback
Playback
File List
Record
Language
Network
MAIN MENU
Date/Time
Setup
Password
Video/Audio
Alarm Setup
E-mail Setup
Info
Motion Detect
Advanced
Mobile
Maintain
PTZ Setup
HDD Management
17
Area
User’s Manual
6.2 Main Menu
Right-click the mouse, a pop-up menu will be displayed on
the screen. Click “MAIN MENU” button on the pop-up menu
to enter into Main Menu. In Main Menu, you can change
settings such as Camera, Playback, Record, Network. Set
system settings, such as Language, Date/Time setting, User
password, Video/Audio, and Advanced settings such as
Alarm, Motion Detection, Mobile Phone, PTZ (Pan Tilt Zoom)
Control etc. You can also access System Information,
System Maintenance etc.
6.2.1 Camera setup
Select Main Menu  Cameras to open the CAMERA
SETUP menu. You can set up the name display and
position display of each channel, You can also adjust
image brightness, saturation, contrast and hue settings of
each channel by entering the “COLOR” Menu and set up
whether each channel can be previewed or not under
Live display and/or Recording mode.
Note: that the name of each channel supports up to eight
characters.
COLOR SETUP Menu allows you to adjust image
brightness, saturation, contrast and hue of each channel.
Click “APPLY” to and then click “OK” to save the adjusted
settings. Click “EXIT” to cancel the modification, or click
“DEFAULT” to restore all settings to the factory default
settings.
18
User’s Manual
6.2.2 Playback
To access the VIDEO SEARCH menu, select Main Menu  PLAYBACK to open the RECORD
SEARCH menu.
To search for a file, enter specific date and click “SEARCH”,
you will find all the recordings of that day. You can play video
Forward at 2x, 4x, and 8x speeds, Slow play at 1/2x, 1/4x,
1/8x, or normal play, pause and play frame by frame using
the playback control bar. When playback is finished, system
will return to previous menu.
To search by file, click the “FILE LIST” button. This option will allow you to view all of the
available files by channel and type (all, normal, or alarm).
You can select a file and push the SEL button to playback the file, or use the FWD button and
down button to select options or backup the recorded file you selected. You can also put a
check mark in the box at the end of multiple files if you want to backup more then one file at
a time.
First:Indicates the first page of recording history you have
searched. When you view other pages, clicking [First] button
brings you back to Page one.
PREV (Previous page): When viewing event list, clicking
“Previous page” button will take you back to page before the
one you are currently viewing (except the first page).
NEXT (Next page): When viewing event list, clicking “Next
page” button will take you to the page after the one you are
currently viewing (except the last page).
LAST (Last page): Indicates the last page of recording history you have searched. When you
view other pages, clicking the “Last page” button will take you to the Last page of the
searched files.
ALL (Select All): Allows you to select all of the events on the current page.
INV (Select Invert): Allows you to revert the selected and unselected events on the current
page except those you have currently selected.
BACKUP: If you want to backup one recording from the file list, select the file and click
“BACKUP”. When the backup is complete, you will be notified. Please click “OK”.
19
User’s Manual
6.2.3 Backup
Use the File List sub-menu to find recorded video on your system and copy it to a USB flash
drive (not included).
NOTE: The system is compatible with most major brands of USB flash drives, with capacities
from 256 MB to 4 GB or may be higher.
To backup recorded data:
1. Connect an empty USB flash drive to the bottom USB port on the back panel of the
system.
2. Open the Search menu and search for recorded data on the system.
3. Click FILE LIST.
4. Select the files you want to backup and click the "SEL" box next to the file name, select
multiple files if desired. Click ALL to select all files; click “INV” to deselect all files.
NOTE: The size of each file is shown in the File List menu. Use this to help you find a USB
flash drive large enough to hold all the files you wish to backup.
5. Click BACKUP from the side-panel to immediately begin copying the files to the USB flash
drive.
NOTE: Backup progress appears in the status window. DO NOT remove the USB flash drive
during backup.
6. If backup is successful, click OK in the confirmation window and then remove the USB
flash drive.
NOTE: If there is not enough space on the USB flash drive, the system will display the
following: "Space is not enough."
6.2.4 Backup File Data
The system will create a folder on the USB flash drive named RecordFile. The files are saved as .264
files.
Note: Backup file will be in H.264 format, you can convert it to AVI format using the Multimedia
Player program that comes with the DVR or through the net-viewer program, so you can
use any player that supports AVI format.
6.2.5 Converting Files to AVI:
Use the built-in browser-based remote surveillance software to convert saved video files to AVI.
The AVI format allows you to playback the video files in many multimedia players. AVI conversion
involves two parts: selecting a file, then converting the file.
To select a file:
1. Open Internet Explorer. In the address bar, enter the IP address of your system.
2. Log in using your ADMIN password. If passwords are not enabled on your system, leave the
password field blank.
3. Click PLAYBACK at the top of the main screen.
4. Use the calendar to select a date and click REFRESH.
5. Find a desired file from the File List and double-click to playback the file in the main screen.
To convert the file:
1. With a file selected and played back in the main screen, click 264 TO AVI. The AVI Convert window
will open.
20
User’s Manual
2. Under SOURCE FILE, click to select the .264 file you wish to convert. By default, the file you have
already viewed in playback should be selected.
3. Under DESTINATION FILE, click to select the save directory for the converted file. Enter a name
for the file. By default, converted files are saved to C:\DVR\.
4. Click CONVERT. File conversion begins. The progress bar indicates the status of the conversion.
Click OK in the confirmation window.
NOTE: You can view the AVI file in media players such as VLC and DivX Player. The DivX, XviD, or FFDShow
codec (not included) is required if viewing AVIs in Windows Media Player.
6.2.6 Record setup
Select Main Menu  RECORD to open the RECORD
menu. The adjustable options are as follow:
CHANNEL: Allows you to turn each channel ON/OFF.
QUALITY: Choose between “BEST”, “FINE”, and
“NORMAL” resolution.
REC. MODE: Choose between Time Scheduled Record or
Always On Recording. Timed recording will allow you to
set motion detection or record at a specific time of
day/night.
File Length: Select the time limit of each recorded file.
Note: Select Time Schedule Record and the select Schedule to access the below menu.
SCHEDULE recording options include ALL, CH-1,
CH-2…CH-8 respectively. Please select the option you
need to record according to the schedule, the channel you
have set will be highlighted.
To setup weekly schedules, click on the box of the corresponding time. Choose between
ALARM, TIMED, or NO RECORD and then click on each box in the schedule time line that
you want to apply the select record type to. You can also use the “From – To” pull-down
menus and Copy button to copy settings from one day to another. After you have
completed the schedule, click “SAVE” button to save the settings.
You can also click on the Default button to use the system defaults. The system default settings
are:
Alarm all time on = Motion Detection = ON
Note: Under the RECORD SETUP menu and record search menu, original color stands for no
recording, “Red” stands for alarm recording, “Green” stands for normal recording and “Blue”
stands for the channel and date you have selected.
21
User’s Manual
6.2.7 Network Setup – Intranet (Internal Access)
To access the NETWORK SETUP menu, select Main Menu  NETWORK to open the
NETWORK SETUP menu.
If your DVR is connected to a router of your local network (intranet), then you can setup the
NETWORK Setup section of the DVR to view the image your DVR is recording remotely
using computers connected within your network.
Important Note: You will not be able to access your DVR if your DVR is connected behind two
or more routers.
Note: Prior to changing the NETWORK Setup of your DVR, it is strongly recommended that
you perform the following tasks:
1. Access the configuration page of your router.
2. Reserve an IP Address in your router that is not used by other computers or devices
connected to your internal network.
3. Write down the assigned IP Address of your DVR, Subnet Mask, IP Address of your Router
(Gateway) of your DVR for future reference when configuring the DVR.
1. Select STATIC as the network TYPE.
2. Setup PORT and WEB PORT (recommended to
leave these at the default values).
3. Enter the IP Address that you have reserved at the
beginning of this section into this field to be the unique
address of your DVR in your local network.
4. SUBNETMASK: It is recommended to leave the
Subnet mask as the default 255.255.255.0.
5. Set the GATEWAY to the IP Address of your router.
6. Enter the DNS (Domain Name Server) Address, Set
this to you router's IP address.
7. Click “APPLY” to save your change.
22
User’s Manual
6.2.8 Network Setup – Global Access (Connected Directly to Modem)
To access the NETWORK SETUP menu, select Main Menu  NETWORK to open the
NETWORK SETUP menu.
If you would like to access your DVR while you are outside of your home, please follow the
instructions below to configure the NETWORK Setup page of your DVR
Important Note: If you are using a DSL modem, the modem must be set to “bridge mode”.
Important Note: We will not be able to help you set up the network configurations if you have a
RADIUS Server or Network Magic installed.
Note: Prior to changing the NETWORK Setup of your DVR, it is strongly recommended that
you perform the following tasks:
1. Find out from your Internet Service Provider (ISP) what kind of service you are using.
Note: Your DVR supports these three common types of Internet Services: DHCP (Cable
Modem), PPPoE (DSL Modem) and Static IP (Fiber Optics). Actual service type may vary,
please ask your ISP for the exact service type.
2. Write down the: IP Address provided by your ISP (if your ISP is using Static IP), Subnet
Mask, Gateway Address, DNS Address(es) provided by your ISP of your DVR for future
reference when configuring the DVR.
DHCP
1. If your ISP uses DHCP networking, select DHCP
network TYPE.
2. Leave MEDIA PORT at 9000
3. Setup WEB PORT (leave at 80 but some ISPs block
inbound traffic on port 80 to prevent web servers so
if the DVR cannot be remotely accessed choose a
different port number)
4. Click the “DDNS SETUP” Button.
5. You will need to apply for a Dynamic DNS account
and register a Domain Name with one of the known
DDNS provider. Enter your DDNS Provider’s
HOST NAME, USERNAME, and PASSWORD in
the DDNS SETUP page.
NOTE: If you would like a free DNS account please visit
www.nightowldvr.com
23
User’s Manual
STATIC IP
1. Select STATIC as the network TYPE.
2. Leave PORT at 9000
3. Setup WEB PORT (leave at 80 but some ISPs block
inbound traffic on port 80 to prevent web servers so
if the DVR cannot be remotely accessed choose a
different port number)
4. Enter the IP Address that you have reserved at the
beginning of this section into this field to be the
unique address of your DVR in your local network.
5. SUBNETMASK: It is recommended to leave the
Subnet mask as the default 255.255.255.0.
6. Set the GATEWAY to the IP Address of your router.
7. Set the DNS (Domain Name Server) Address to the
IP Address of your router
8. Click “APPLY” to save your changes.
PPPoE
1. If your ISP provides you a Static IP Address, select
STATIC as the network TYPE.
2. Leave PORT at 9000
3. Setup WEB PORT (leave at 80 but some ISPs block
inbound traffic on port 80 to prevent web servers so
if the DVR cannot be remotely accessed choose a
different port number)
4. Enter your PPPoE NAME and PASSWORD so your
DVR will be able to obtain service from your ISP.
5. Enter the DNS (Domain Name Server) address.
6. You will need to apply for a Dynamic DNS account
and register a Domain Name with one of the known
DDNS provider. Enter your DDNS Provider’s
HOST NAME, USERNAME, and PASSWORD in
the DDNS SETUP page.
6.2.9 Network Setup – Global Access (Connected through a Router or Firewall)
To access the NETWORK SETUP menu, select Main Menu  NETWORK to open the
NETWORK SETUP menu.
If you would like to access your DVR while you are outside of your home or office network,
please follow the instructions below to configure the NETWORK Setup of your DVR
Important Note: You will not be able to access your DVR if your DVR is connected behind two
or more routers.
Important Note: If you are using a DSL modem, the modem must be set to “bridge mode”.
Important Note: We will not be able to help you set up the network configurations if you have a
RADIUS Server or Network Magic installed.
Note: Prior to changing the NETWORK Setup of your DVR, it is strongly recommended that
you perform the following tasks:
24
User’s Manual
1. Access the configuration page of your router or Firewall.
2. Reserve an IP Address in your router or firewall that is not used by other computers or
devices connected to your internal network.
3. Make sure your router is configured properly for computer or devices outside of your local
network to access your DVR through your router. To do so, please use the following
method(s): NAT (Network Address Translation), Port Forwarding, DMZ (De-Military Zone),
DDNS (Dynamic DNS). Please refer to your router or firewall user’s manual for reference.
Note: Improper configuration on the router or firewall will prevent you from accessing your
DVR from outside your network.
4. Write down the assigned IP Address of your DVR, Subnet Mask, IP Address of your Router
(Gateway) of your DVR for future reference when configuring the DVR.
1. Select STATIC as the network TYPE.
2. Leave PORT at 9000
3. Setup WEB PORT (leave at 80 but some ISPs block
inbound traffic on port 80 to prevent web servers so if
the DVR cannot be remotely accessed choose a
different port number)
4. Enter the IP Address that you have reserved at the
beginning of this section into this field to be the unique
address of your DVR in your local network.
5. SUBNETMASK: It is recommended to leave the
Subnet mask as the default 255.255.255.0.
6. Set the GATEWAY to the IP Address of your router.
7. Set the DNS (Domain Name Server) Address to the
IP Address of your router
8. Click “APPLY” to save your changes.
Port Forwarding
To access the DVR from a remote computer over the internet via internet browser (Internet
Explorer).
1. Forward Port 80 and Port 9000 in the router attached to the DVR, to the IP address of
the DVR. *If you can’t use HTTP Port 80 due to use or your Internet Service Provider is
blocking it, use a different port like 1024 as the WEB PORT. When selecting a different
port, forward the new port to the IP address of the DVR and change the settings in the
DVR Network settings. You will also need to add the new port to the end of the IP
address in the browser window. For example, if you use port 1024, you add “:1024” to
the end of the IP address.
2. For instructions on the most popular routers go to www.portforward.com. Click on the
“Routers List” and select your router from the list of router manufacturers by clicking on
the brand and model number.
25
User’s Manual
3. On the next page that opens, click on the “Default Guide” link.
port forwarding instructions for your router.
This will take you to the
4. When you access the DVR from a remote computer, you also need to use a different
address in the Internet Explorer browser window. Instead of entering the IP address of
the DVR, you need to enter the public IP address of the router that the DVR Is attached
to. You can get this address by going to www.myipaddress.com from the
computer that is attached to the same router as the DVR. This website will display the
box in that shows the IP address you need to use.
Accessing the DVR through Internet Explorer Browser (IE):
Once the network settings on the DVR match the settings of your router, and you have
forwarded the ports needed by the DVR (for remote access over the internet), you need
to modify your browser controls.
Note: Ensure you are using Internet Explorer 7 or newer to use this feature (Open IE, Click
Help, Select “About Internet Explorer”)
To Modify Internet Explorer controls
1. Turn OFF “Pop Up Blocker”
Go to Tools,
Select Pop-up Blocker,
If On please select “Turn Off
Pop-up Blocker”
26
User’s Manual
2. Access Active X Controls
Select Tools
Select Internet Options
Access Custom Security Level
Select the “Security” tab
Select “Custom Level…”
3. Enabling all Active X Controls
On this page scroll down to the ActiveX
Controls and Plug Ins, and set all to either
PROMPT or ENABLED.
To connect to the DVR from a remote computer, you would then open an Internet Explorer
browser window and enter the Internet IP of your router that you received by going to
www.myipaddress.com.
27
User’s Manual
If you get an error message “Program cannot load because the Publisher is unknown” or the
program is unsigned, then go to Internet Explorer > Tools > Internet Options, then click on
the ADVANCED tab on the top right. This will open the window in, scroll down to “Security”,
and select on the options to “Allow software to run or install even if the signature is invalid”,
and “Allow Active Content to Run Files on My Computer”.
Warning! It is strongly recommended to return all Internet Explorer Security to its default
settings after the Active X Control has been installed. Enabling all Active X controls put
your computer at risk of being attacked by malware and spywares.
6.2.10 Basic Setup
To access the BASIC SETUP menu, select Main
Menu  SETUP to open the BASIC SETUP menu.
The BASIC SETUP Menu includes: LANGUAGE,
DATE/TIME, PASSWORD, and VIDEO SETUP.
6.2.10.1 Language
Click “MAIN”  “SETUP”  “LANGUAGE” to
setup the default system language.
6.2.10.2 Time Set
Click “MAIN”  “SETUP”  “DATE/TIME” to enter the TIME SETUP window to modify
system date, time, date/time format and time zone, DST (day saving time).
•
•
•
•
DATE: Enter the day, month, and year
DATE FORMAT: Select DD/MM/YYYY,
MM/DD/YYYY, or YYYY/MM/DD
TIME: Enter the time
TIME FORMAT: Use the drop-down menu and
select 12HOURS or 24HOURS
28
User’s Manual
6.2.10.3 Password
Click “MAIN”  “SETUP”  “PASSWORD”. This
option allows you set the device ID for the DVR
and set the system password if you want to use
one. Click “APPLY” to save the settings.
.
When you have enabled Password by setting the
option to “ON”, you can setup a user password and
administrator password respectively. The password
supports up to 6 characters. Click “APPLY” to save
the settings.
NOTE: Please write down your passwords and
store in a safe location.
6.2.10.4 Video Setup
Click “MAIN”  “SETUP”  “VIDEO SETUP” to
setup Video output options such as resolution and
camera system.
6.2.11 Advanced Setup
To access the ADVANCED SETUP menu, select Main
Menu  ADVANCED to open the Advanced Setup menu.
The available options are: ALARM, INFO, MD (Motion
Detect), MOBILE, MAINTAIN, PTZ (Pan-Tilt-Zoom), and
HDD (Hard Disk Drive).
29
User’s Manual
6.2.11.1 Alarm Setup
To configure the Alarm mode of each channel,
click “Main Menu”  “ADVANCED”  “Alarm” to
enter into “ALARM SETUP” menu.
HDD LOSS: Set this to ON if you would like to
trigger the alarm when HDD is operating irregularly.
HDD SPACE: Set this to ON if you would like to
trigger the alarm when the “HDD Overwrite” option
is disabled and the HDD is full.
VIDEO LOSS: Set this to ON if you would like to trigger the alarm when any of the camera
signal is distorted or loss.
ALARM MANAGE OUTPUT: Option for the duration of the external alarm after an alarm is
triggered (Not Applicable for this particular series of machines).
BUZZER: Option for the duration of the built in buzzer after an alarm is triggered
Post Alarm Recording: If “Motion Detect” recording is enabled, this option controls the
duration of the recording time after the motion has stopped.
EMAIL SETUP: There is also an option for the DVR to send an e-mail to a specific mails
box when the alarm is triggered. To enable this option, follow these steps:
Click the “EMAIL SETUP” button under ALARM
SETUP.
Set the e-mail account information of your mail
server. Please contact your Network
Administrator for details and configuration
settings.
6.2.11.2 System Information
Click “MAIN”  “ADVANCED”  “INFO” to access
the system information of your DVR.
30
User’s Manual
6.2.11.3 Motion Detect
To configure the Motion Detection function of
the DVR, click “MAIN”  “ADVANCED”  “MD” to
enter the MOTION DETECT window.
STATUS: This option allows you enable motion
detection on the channels.
SENSITIVITY: This option allows you to set
sensitivity level of motion detection from 1 to 4 with 4
being the most sensitive.
MD AREA: Click this button of the corresponding
channel to select the area you want to have motion
detection. The channel is separated into a 13*10
area. When any movements in the selected area are
detected, recording or alarm will be triggered. The
semi-transparent area means no motion detection
will be performed in those areas.
Red = Motion Detection Enabled
Clear = Motion Detection Disabled
NOTE: You can click and drag the mouse cursor when selecting/deselecting the motion area.
6.2.11.4 Mobile Phone Access
If you would like to allow your DVR to be
accessible by a Mobile device, click “Main Click
“MAIN MENU”  “ADVANCED”  “MOBILE” to
open the “MOBILE” menu.
Server Port: It is the mobile monitoring port.
Setting range is between 1024 and 65535.
Please note that the server port number must not
equal to network menu’s “PORT” setting.
31
User’s Manual
®
The DVR is currently compatible with mobile phones running Windows Mobile,
Symbian® S60 Version 3 or 5 operating systems and iPhones® on 3G networks.
Before you can access the DVR from a mobile phone, you need to setup the Network
Configuration on the DVR. Go to section 6.2.8 or 6.2.9 for instructions. You will also
need to set the configurations in section 6.2.10.3 and 6.2.11.4.
NOTE: The video speed depends on the speed of the internet connection.
When accessing from a mobile phone with Windows Mobile operating system,
follow these procedures:
1. Install the webcam program that is included on the supplied CD by copying the
“QQeye.CAB” file to the mobile phone. You can do this by attaching the mobile phone
to a computer and copying the file from the CD to the phone.
2. Click the windows mobile folder and choose the file “QQeye” Select the file which will
open the window. The file is generally default to save to the Device’s built-in memory,
but you can choose to save it to Storage Card.
3. Choose storage location and click “Install” to start the installation.
4. After installation finishes, click the icon named QQeye to run the program. This will
display the program screen.
5. Click the “Setting” button to enter the Setting menu.
User name: same as the user name setup in DVR under section 6.2.10.3.
Password: same as the password setup in DVR under section 6.2.10.3.
Server address: Enter the Public IP or DDNS address of your DVR.
Web port: Same as the Server Port you set in the DVR under section 6.2.11.4.
Channel: Select the channel you want to monitor and click “OK” to display the screen to
start viewing the live image.
32
User’s Manual
6. To stop viewing the live video, click the “Disconnect” button or click the “Setting” button
to modify the settings.
When accessing from a mobile phone with Symbian® S60 Version 3 or 5 operating
system, follow these procedures:
1. Install the webcam program that is included on the supplied CD by copying the
“QQeye.SISX” file to the mobile phone. You can do this by attaching the mobile phone
to a computer and copying the file from the CD to the phone.
2. Select the QQEye icon in this window to install it.
3. After the phone finishes copying the file, it will ask for permission to install the program.
Select “Yes” to start the installation.
4. Click the “Continue” button on the information box displaying the program and current
version.
5. Select the location of where you want to install the program, to phone memory or to the
memory card, and then click “Select”.
6. Click “Continue” and wait for the program to install.
33
User’s Manual
7. Once the installation is complete, go to the Applications folder and select the “QQEye”
program, and click “Open” to display the settings menu.
Open
Default Access Point:Input the access point. System default for the access point is
GPRS connection.
Server Address:Enter the Public IP or DDNS address of your DVR.
Server Port:Same as the Server Port you set in the DVR under section 6.2.10.3.
User Name: same as the user name setup in DVR under section 6.2.10.3.
Password:same as the password setup in DVR under section 6.2.11.4.
Channel: Select the channel you want to monitor and click “DONE” to display the screen
to start viewing the live image.
When accessing from a mobile phone with an iPhone® follow these procedures:
1. From you iPhone® Select “App Store” from your home screen.
2. Select the Search icon.
3. Type: “cplayer” in the search field
4.
5.
6.
7.
Select the “cplayer” application just below the search feature
Click on “Free”.
Click Install.
Follow the on screen instructions to complete the installation.
34
User’s Manual
®
8. Once installed click on the application icon in your iPhone home screen to open the
application.
9. Select the Settings icon on the bottom right and input your Server IP, Mobile Port
number and Password (See Section 6.2.11.4 Mobile)
10. You will now be watching a live streaming video of your security camera on your
iPhone®. Enjoy!
NOTE: If you are having trouble accessing your DVR from your cell phone please visit
www.NightOwlSP.com to ensure you are using the most up to date software. If your
phone is not compatible with the above list please check our website once again to
see if your phone is listed.
6.2.11.5 System Maintenance
6.2.11.6 PTZ Setup
Click “MAIN”  “ADVANCED”  “MAINTAIN” to
access the SYSTEM MAINTENANCE page of your
DVR. This option allows you reset the DVR to
factory default settings, update system software
(firmware), and set system auto-maintenance.
When enabling the auto-maintain function, you can
setup system to restart regularly to clear up some
temporary storage memory.
To configure the PTZ (Pan Tilt Zoom)
function, click “MAIN MENU” 
“ADVANCED”  “PTZ”. The cameras that
come with the kit do not support PTZ
function, please refer to the user’s manual of
your PTZ cameras for proper settings.
Please note the above mentioned channel
settings must match the settings of the PTZ
camera.
35
User’s Manual
6.2.11.7 HDD Management
To manage the installed Hard Disk, click “Main
Menu”  “ADVANCED”  “HDD” to enter “HDD
MANAGEMENT”. The HDD Management screen
shows the capacity and available recording time of the
installed hard drive and let you configure whether to
overwrite old recordings or stop when HDD is full.
Select “HDD Format” to format the installed Hard Disk
Drive and erase all recorded files.
Select “USB Format” to format the installed USB Drive
by erasing all recorded files on the drive.
To enable your DVR to overwrite old recording files,
choose “ENABLE” at the OVERWRITE field and then
click Apply.
36
User’s Manual
6.3 KEYLOCK
Select this option to activate the password protection. You will need to first setup the User and
Admin Password before you can apply this option.
6.4 CHANNEL SWITCH
Click pop-up menu -> CHN SWITCH to open the sub menu. Choose display between Quad or
any of the individual channel in full screen.
6.5 Video Search
Click pop-up menu video search to open the “Video Search” menu to search for files and
playback recordings.
6.6 PTZ Control
Click pop-up menu to show the PTZ option and open the PTZ
control interface. You can now click Z+ & Z- keys to zoom In or
out, click F+ & F- keys to control camera focus and click I+ & I- to
adjust the focus point.
6.7 MANUAL REC
If you want to start manual recording, click “MANUAL REC” on the Pop-up menu or the
“MANUAL REC” button.
6.8 Stop Recording
If you want to stop manual recording, click “STOP REC” on the Pop-up menu or the “STOP
REC” button.
37
User’s Manual
CHAPTER 7: NET-VIEWER PROGRAM
Open Internet Explorer and enter the IP Address or DDNS address of your DVR. A pop-up will ask
you to install an ActiveX (plug-in) to your computer. Please confirm the download and install the
software.
Reminder: If the ActiveX (plug-in) is not downloaded successfully, please check if your
browser’s safety level or firewall setting is set properly (as stated above). Please also make sure all
of the setup of your modem or router is setup properly.
7.1 Log-in to Net-Viewer
After the ActiveX (plug-in) is installed, please enter
the login information. Click the “LOGIN” button to
view remotely through NetViewer.
Please note default password is empty. System
allows Administrator to set new password as per
section 5.2.8.4.
After successfully Logged in to Net-Viewer,
system will open the live display interface and
connect to audio/video feed automatically.
38
User’s Manual
7.2 Main Interface of Net-viewer
7.2.1 Menu column
Menu column includes “LIVE”, “PLAYBACK”, “SETUP” and “EXIT”.
7.2.1.1 Live
After Logging-in to system, system will enter into Live display.
7.2.1.2 Playback
This option allows you to playback
recordings remotely.
1. Select the day, channel and type and
proceed searching and refreshing.
2. Select any event from search result list
to playback.
Below are some explanations of the
buttons.
Play: [Play]/[Pause]
Stop: stop playing recording.
F.F.: fast forward playback recording
Slow: slow playback recording.
Next Frame: play frame by frame.
264 TO AVI button: convert file from H.264 format to AVI format
The native format of the backup files is H.264, you can convert H.264 format into AVI format
by clicking the key of 264 to AVI.
39
User’s Manual
7.2.1.3. Setup
Click “SETUP” open this sub menu, option in this menu includes “Recording Mode”, “Alarm
Mode”, “PTZ Control”, “Network Setting”, “System Setting” and “Host Info” .
Record
Open sub menu “Recording Mode”, you can select
on/off for every channel, and adjust recording
parameters (quality, REC mode and Schedule)
remotely via Net-Viewer.
Open “Schedule” sub menu to.
Set up the recording schedule using this option.
Alarm
Open sub menu “Alarm”.
You can set I/O alarm for every channel, motion
detection alarm, motion recording, motion trace, motion
sensitivity, video loss alarm, HDD not enough space
alarm, HDD not found alarm and alarm output time etc.
This option allows you set motion detection settings for each
channel of the DVR remotely.
40
User’s Manual
PTZ Control
Open” PTZ Control” sub menu. Remotely setup
methods are the same as configuring on the
DVR.
Network
Open “Network” to enter the “Network”
sub menu. Remote setup methods are
the same as configuring on the DVR.
Setting
Open “Setting” sub menu to open the menu.
Click […] button to preview Net-Viewer’s recorded
file saving path and screen capture saving path.
The menu also allows you to set a lower bandwidth
for Internet video transmission, set user password,
turn daylight saving time on/off, etc.
Host Info
Open “Host Info.” to open the sub menu. You can
check usage rate of HDD, available recording time,
software version and MAC address.
7.2.1.4 Exit
Log out of the system.
41
User’s Manual
7.2.2 PTZ Control
1. PTZ direction control: Control PTZ moving direction
2. Zoom, Focus and Iris Control: control direction, zoom, focus and iris of PTZ.
7.2.3 Live Play Control
1. On / Off Live display [
]:When Live display status is “On”, Clicking the button closes Live
display. When “Off” clicking the button opens the Live display.
2. Capture [
3. Recording [
]:Capture Screen image and save to PC as *bmp image.
]:Operate DVR recording remotely
4. Channel display [
]:The icons stand for Single Channel display, Quad
Channel display, 3x3 Channel display and 4x4 Channel display respectively.
42
User’s Manual
7.2.4 Remote Backup
You can backup recorded video files from your system to your PC using the Replay menu in
the remote surveillance software.
To backup files remotely:
1. Click PLAYBACK at the top of the main screen.
2. Select a date(s) on the calendar and click REFRESH.
3. Double-click a file from the File List to begin playback.
4. Click BACKUP. Backup begins to C:/DVR/[ip_address]/Backup
NOTE: If you playback a file, you must wait for the file to load before backing it up, otherwise
you may receive an error message
5. When file backup is complete, click OK in the confirmation window. The confirmation
window show the save path of the backup file.
NOTE: Backup files are saved as .264 files.
NOTE: Use the Player Software included on the software CD to playback backed up video.
7.2.5 Multi Player File format
1. If you would like to play any recorded file using video players that supports .avi format, first,
copy or backup file to your PC.
2. Open the multimedia player installed on your computer, click File Open Local File, to
find/select the backup file, and then click “Open”.
Note: the file type you have selected should be *.264 format.
3. Open backup file, click the “Play” menu to play the file.
43
User’s Manual
4. Click pop-up menu button
on the bottom of multimedia player and click “Play (
button, then the backup file will be played accordingly.
At the upper right hand corner, the date of when the file was recorded will be displayed.
At the lower left hand corner, the 24H recording time is shown.
The control buttons for video playback is at the bottom of the screen.
The current playing point of the video file is shown above the control buttons.
)”
Recording date and time processing for the current recording file
1
Play
10
All the windows
2
Previous recording file
11
Add window
3
Pause
12
Start
4
Stop
13
Cut
5
Previous frame / Next frame
14
Delete
6
Slow play, Normal play, Fast 15
Convert AVI
7
Next Hour
16
OSD
8
Capture picture
17
Mute switch
9
Reduce window
18
Volume adjust
5. To enable a specific channel video to play, select “Setting”  “Video Play Setting” 
“Normal Video Bar”. Select the channel you want to enable/disable, and check the check
box to enable the channel.
44
User’s Manual
6. To enable a specific channel’s audio, select “Setting”  “Audio Channel Setting”  “Normal
Video Bar”. Select the channel you want to enable/disable, and check the check box to
enable the channel.
Please restart the multimedia player after the configuration is changed.
45
User’s Manual
WARRANTY
NIGHT OWL, LLC (“Night Owl”) provides the following warranty to the original retail purchaser only (the
“Purchaser”) with respect to this product (the “Product”):
For a period of one (1) year after the date of sale, the Product shall be free from manufacturing defects in
material and workmanship. In the event that the Product is defective, the Purchaser must return the Product at
Purchaser’s cost (no CODs) to the address below, with the original proof of purchase receipt.
In its sole
discretion, Night Owl will either repair or replace the Product at no additional cost to the Purchaser. Any
replacement Product (or parts) will be covered by the same warranty as the original Product through the
expiration date of the original warranty period.
Exclusions:
This warranty does not apply to the following parts or upon the following events:










Bulbs, LEDs and batteries;
The Product was not used or installed in the manner described in the installation instructions;
Negligent use of the Product, or misuse or abuse of the Product;
Electrical short circuits or power surges;
Use of replacement parts not supplied by Night Owl;
Product is either tampered with, modified, or repaired by another service provider;
Product has not been maintained in accordance with the instructions;
Accident, fire, flood or other acts of God;
Failure to use Night Owl approved accessories;
Defects or damages arising by use of the Product in other than normal conditions (including
normal atmospheric, moisture and humidity conditions).
EXCEPT AS OTHERWISE PROHIBITED BY LAW, THIS WARRANTY IS IN LIEU OF OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND NIGHT OWL NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY IN
CONNECTION WITH THE SALE OR SERVICE OF THE PRODUCT.
IN NO EVENT SHALL NIGHT OWL BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL
DAMAGES ARISING FROM THE USE OF THE PRODUCT OR ARISING FROM THE
MALFUNCTIONING OR NON-FUNCTIONING OF THE PRODUCT, OR FOR ANY DELAY IN THE
PERFORMANCE OF THIS WARRANTY DUE TO ANY CAUSE BEYOND ITS CONTROL. THIS
WARRANTY SHALL NOT APPLY TO INSTALLATION OR THE REMOVAL AND
REINSTALLATION OF PRODUCTS AFTER REPAIR.
Night Owl does not make any claims or warranties of any kind whatsoever regarding the Product’s potential,
ability or effectiveness to prevent, minimize, or in any way affect personal or property damage or injury. Night
Owl is not responsible for any personal damage, loss or theft related to the Product or to its use for any harm,
whether physical or mental related thereto. Any and all claims or statements, whether written or verbal, by
46
User’s Manual
salespeople, retailers, dealers or distributors to the contrary are not authorized by Night Owl, and do not affect
this provision of this warranty.
Returns under this Warranty
In order to obtain service, please make sure that you have registered your product on-line no later than thirty
(30) days after purchase at www.NightOwlSP.com in the warranty registration section or in any other matter
described in the instructions.
TOLL FREE CUSTOMER SERVICE
North America: 1-866-390-1303
1-774-256-7250
Email: Support@NightOwlSP.com
Website: www.NightOwlSP.com
Email:
Support@NightOwlSP.com
TOLL FREE: 1-866-390-1303
Rev 04-2010
47
User’s Manual
48
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising