KWorld PLUSTV 1680ex User manual

Add to my manuals
18 Pages

advertisement

KWorld PLUSTV 1680ex User manual | Manualzz
PLUSTV 1680ex
USER’S MANUAL
Ver 1.0
Contents
1. Instruction .............................................................................................................................................. 1
1.1 Functions and features ................................................................................................................. 1
1.2 Packaged contents ........................................................................................................................ 2
1.3 Technical specifications ............................................................................................................... 3
2. Remote control instructions ................................................................................................................... 4
2.1 Diagram of remote control and buttons description..................................................................... 4
3 Hardware &installation instructions ....................................................................................................... 6
3.1 Product picture and panel description .......................................................................................... 6
3.2 Rear panel description.................................................................................................................. 7
3.3 Connection illustration.............................................................................................................. 8
3.4 Installation and Channel scan for the first time .................................................................... 9
4. Menu display and description .............................................................................................................. 10
4.1 Menu display and description .................................................................................................... 10
4.2 Program searching...................................................................................................................... 13
4.3 Operations for PIP function at PC mode .................................................................................... 14
5. Operations for game function............................................................................................................... 14
6. Troubleshooting ................................................................................................................................... 15
Thank you for buying KWorld’s PLUSTV 1680EX .
For better use of the product, please read this User’s Manual carefully before use.
This User’s Manual is for specific product, and all its contents are processed with
due care but are not ensured fully correct.
We assume no responsibility for any loss arising from use of this manual.
The right to interpret all contents of this User’s Guide belongs to the company
The manual is subject to change without notice.
This User’s Manual is not authorized to any party and no reproduction or copy,
in part or whole, of the manual in any way is permitted.
KWorld Website: www.kworld.com.tw
1. Instruction
The PLUSTV 1680EX uses the professional progressive scanning TV (DPTV) chip,
which adopts such picture improvement technologies as black level stretch, video
noise suppression, and 3D motion compensation etc, so it gives clearer and more
flamboyant pictures and stronger three-dimensional perception.
In addition, its specific scanning frequency increasing technology increases the
refresh frequency from original 50Hz to 60Hz or 75Hz* (optional), which effectively
conquers the large area flicker and interline flicker in picture caused by the low
refresh frequency (50Hz only) of ordinary TV and improves the stability of picture,
so it can reduce the visual fatigue due to long TV watching.
The PLUSTV 1680EX can support CRT monitor and traditional or wide-screen LCD
monitor. It is the increases of fresh frequency and resolution (up to 800X600/
1024X768/ 1280X1024/ 1440X900/ 1680x1050) that solve the problem that
ordinary PC TV receiver is not compatible with LCD monitor. Connecting this
product with an LCD monitor, you can easily get a fashionable and healthy LCD TV.
The PLUSTV 1680EX has PIP (Picture In Picture) function at PC mode, which
allows you to enjoy wonderful TV programs while operating PC, so neither work nor
entertainment is held up. Furthermore, it has multi-channel pre-view function, which
enables you to view the program of each channel conveniently.
In addition, the PLUSTV 1680EX has 3D noise reduction function, which makes the
picture more exquisite, clearer and more stable.
1.1 Functions and features
z
Advanced scanning frequency increasing technology to make the refresh
rate up to 60Hz or 75Hz, which delivers stable pictures without flicker.
z
Resolution can be conveniently changed over among 800X600/ 1024X768/
1280X1024/ 1440X900/ 1680X1050. Be fully compatible with CRT monitor
and traditional or wide-screen LCD monitor.
z
Support 4:3/16:9 picture aspect ratio.
z
9/16-channel pre-view function to facilitate the channel selection.
z
Still-picture function enables you to capture wonderful moments in TV
program.
z
Super 3D picture noise reduction function to make picture clearer and more
stable.
z
Special PIP function to give size and position adjustable window.
*PIP mode can’t work on PC display resolution 1680X1050.
1
z
Full-function remote control and 3D-effect English and Chinese menu
display to give easy operations.
z
VGA/TV output with one click (this function needs to be customized).
z
TV tuner with frequency phase lock (PLL) to offer stable reception. Thus, it
will never occur that the TV program is lost.
z
AV/S-VIDEO/YPbPr input interface can be extended by using MMI cable so
that the product can be connected with DVD, PS2 game machine etc. The
product supports standard-definition and high-definition signal input (480I/
480P/ 576I/ 576P/ 720P/ 1080I).
z
Auxiliary functions such as automatic power up or shutdown within 24 hours,
calendar, calculator, game and etc.
z
Channel number ordering function allows you to arrange the order of
programs as your favorites.
z
PC/TV changeover switch.
z
Composite video output TV program. (OSD can not support in this function )
1.2 Packaged contents
PLUSTV 1680EX
User’s Manual
Remote control
Power adapter
Stereo audio cable
VGA cable
MMI cable (YPbPr, input)
MMI cable (S-video/AV input)
MMI cable (Composite video cable)
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
2
1.3 Technical specifications
Power input: DC 5V, 800mA
TV System Input: 75Ω IEC or type-F
TV System Support: NTSC, PAL, Secam (Depend on the model)
Video Input:
„
Composite video input (RCA)
„
S Video input (4PIN)
„
YPbPr input (RCA)
„
VGA input
Video Output:
„
D-SUB output
„
Composite video output (OSD is not support in this mode)
Audio input & output: Mini jack (stereo 3.5mm)
Resolution
„
SVGA:800x600@ 60/75Hz
„
XGA:1024x768@ 60/75Hz
„
SXGA:1280x1024@ 60Hz
„
WXGA:1440x900@60Hz
„
WXGA+:1680x1050@60Hz
3
2. Remote control instructions
2.1 Diagram of remote control and buttons description
7. Video button
1. Power / Standby
12. NICAM button
5. Timing button
2. Mute
6. Display button
3. 0-9 Channel
4. Return button
16. Aspect Ratio button
18. Factory Default
19. HD button
13. Still Picture
8. Mode button
10. Channel +/-
14. Output Mode
11. Volume +/9. Menu button
17. PIP Function
15. TV Wall button
1. Power/Standby button: Used for power up/standby. At standby mode, it is PC
direct connection state.
2. Mute button: Clicking this button to make the sound disappear. You can click the
button again or click Volume +/Volume - button to resume the sounds.
3. 0-9, -/-- buttons: Used for the selection of channel number.
4. Return button: Used for the skip to the previous program.
5. Timing button: Click this button continuously, the timing of 15-180 minutes for
shutdown and “OFF” will be displayed on the screen in turn. If you set the time
for shutdown, the product will automatically be powered off when the time you
4
set is over.
6. Display button: If this button is clicked, the number of the program you are
watching will be displayed.
7. Video button: Clicking this button continuously, you can change over the mode
among TV/ Video/ S video/ YPbPr circularly.
8. Mode button: Clicking this button continuously, you can change over the picture
mode among the four set modes, i.e. bright, standard, soft and preset. At PC
mode, this button is used for the right movement of window.
9. Menu button: Used to enter into and exit from menu.
10. Program + and Program - buttons: These two buttons are used to increase and
decrease program number, and they are also used to move cursor up and down
during menu operation.
11. Volume + and Volume - buttons: These two buttons are used to adjust volume
and are also used for adjustment in menu.
12. NICAM button: Only supported in PAL-I Nicam model.
13. Still Picture button: Used to still the picture of TV or video program. At PC mode,
it is used for the left movement of PIP window.
14. Output Mode button: Used to adjust the resolution and refresh rate of output
picture. (Note: You can click this button continuously to adjust the resolution and
refresh rate, or you can click the button, use P+ and P- to select item and then
use VOL+ to realize the function.)
15. TV Wall button: Used for multi-channel preview.
16. Aspect Ratio button: Used to adjust picture aspect ratio, i.e. the changeover
between 4:3 and 16:9.
17. PIP button: When there is PC signal input, you can click this button to enter into
PIP function.
*PIP mode can’t work on PC display resolution 1680X1050.
18. Factory Default button: You can click this button to resume the factory default
setting. (Note: If wrong operation by user causes no display on the monitor, you
shall press this button for a long time so as to resume the factory default
setting.)
19. HD button: Not support in this model.
5
3 Hardware &installation instructions
3.1 Product picture and panel description
z
: Power/Standby, OSD menu button, i.e. Press to open OSD
menu. Press 3~5 seconds to switch the Power/Standby.
z
z
z
: Program + and program - button.
: Volume + and volume - button.
LED indicator: Lighting up high for TV or PIP mode.
Lighting up low and flashing for standby mode.
Flashing for command receiving mode.
6
3.2 Rear panel description
VGA: The 15-pin connector end on
the attached VGA cable is
connected to the output of video
card in PC and the other end on
the cable to the VGA port.
MONITOR:
monitor.
Connected
with
AUDIO IN: Audio input port, which
is connected with the output port of
sound card of PC casing through
the attached stereo audio cable.
AUDIO OUT: Audio output port,
which can be connected with the
audio input port of active speaker
or power amplifying device.
MMI-C: For the attached MMI
S-video/AV input, YPbPr input and
video ouput.
DC IN: Power input port (Please
use the attached 5V power
adapter for this product.)
ANT IN: Antenna input port for
CATV or antenna TV signal input.
7
3.3 Connection illustration
8
3.4 Installation and Channel scan for the first time
When you use the PLUSTV 1680EX for the first time, please refer to the hardware
connection illustration in the user’s manual to complete the hardware installation. To
ensure that you can watch and select active channels, please follow the next steps
to setup your TV channels:
1. Press the menu button on
the remote control to enter
the OSD menu.
2. Select the menu of TV
Tuning and enter the
submenu of Tuning.
3. Select Auto to start TV
channel auto scan.
9
4. Menu display and description
4.1 Menu display and description
Menu I: Picture
Contrast, brightness, Chroma, hue can be adjusted from 0 to 100 respectively.
(Note: Hue option can be displayed only if the video input is NTSC system
signal.)
There are two states, ON and OFF, for noise reduction. Noise reduction at ON
state can reduce the noise in picture.
For picture system, there are Auto, PAL, N3.58, N4.43 for selection.
Menu II: System
Adjusting input source, you can change the input mode of the product. There
are four kinds of input source, i.e. TV, video, S-video and YPbPr.
Adjusting Blue Screen ON/OFF, you can turn on or turn off blue background at
no signal state.
CH Preview allows you to set the number of pictures you want to view, and
there are 9 and 12 available.
Display Setup: see Menu III.
Auxiliary option including four sub items: see Menu IV.
10
Menu III: Display setup
Adjusting Output mode, you can change over the resolution and refresh rate of
output picture.
Aspect Ratio, used for the changeover of picture aspect ratio.
Menu IV: Auxiliary
Calendar, used to display year/month/day and week. You can use “P+”/“P-” and
“VOL+”/”VOL-” to adjust year and month.
Calculator to provide simple calculation.
Game function: see section IV of this manual for operations.
Information option, used to find the model number of this product, the revision
number and date of the software and hardware of this product.
11
Menu V: TV Tuning
Channel Number, used for the display of present channel number.
Channel Skip, used to delete the channel with no signal or poor signal.
Channel Swap, used to arrange the order of TV programs as per your liking.
Region: Select your region (TV system) or common.
Tuning: used to search for program. See Menu VI.
Menu VI: Tuning
Antenna select: including Cable and Antenna.
Channel No.: used for the display of present channel number.
Auto: After this option is selected, click VOL+ for auto searching.
Manual: After this option is selected, press VOL+ or VOL- for manual searching.
Fine-tuning: After this option is selected, click VOL+ or VOL- for fine adjustment
of frequency.
12
Menu VII: Timing
Timer OFF: used to set the time for shutdown. It shall be changed to “on”.
Timer ON: used to set the time for startup. It shall be changed to “on”.
Valid time: used to set the valid time of your setting as once or every day.
Startup Mode: used to set the mode for each startup, which can be set as video,
S-video or TV.
Menu VIII: OSD
Language: Select the OSD language.
Style: used to set the style of menu as per your liking, including three options,
classic, modern and romantic.
Horizontal Position: used to adjust the position of menu on screen in left or right
direction.
Vertical Position: used to adjust the position of menu on screen up or down.
Display Time: used to adjust the display time of menu on screen.
4.2 Program searching
z
Connect the antenna plug for CATV or antenna TV to the ANT IN port of this
product.
z
Enter into Tuning menu. Click VOL+ to enter into Tuning menu. Select Auto and
click VOL+ to start auto searching.
z
If the noise level is too high at a certain channel and you do not want to keep it,
you can enter into TV Tuning menu to select CH. Skip. After setting, the channel
will be deleted.
13
z
You can use CH. Swap option in TV Tuning menu to conduct ordering for TV
programs. For example, CCTV-8 and CCTV-12 are now located in channel 8
and channel 12 respectively and you want to arrange them in channel 1 and
channel 2 respectively, you can conduct the following operations: select
CCTV-8, enter into TV Tuning menu, select CH swap option, change the
channel number from 8 to 1, and then click Menu button. Similarly, you can
change over CCTV-12 from channel 12 to channel 2.
4.3 Operations for PIP function at PC mode
z
At TV or PC mode, click PIP button on remote control and wait for 1-2 seconds,
there will be a small window in the upper left corner of screen and the sound is
also changed over. You can click PIP button again to change over the window
to larger one. Click PIP button for the third time, the window is changed over to
small. For fourth click, PIP is cancelled.
z
The adjustment of the position of PIP can be realized through the Still Picture
and Picture Mode buttons on remote control.
z
In addition, at PIP mode, you can use Video button for the changeover to video
or S-video mode.
5. Operations for game function
a. To enter into game: Enter into the menu and select Game under the Auxiliary
menu.
b. Gaming method:
Box,
Destination,
Wall. Pull every box through
up, down, left and right movement. If all boxes are pulled to
the destination, you pass the barrier.
c. Description of function buttons: Program + Æ Up movement
Program - Æ Down movement
Volume + Æ Left movement
Volume - Æ Right movement
Menu button Æ Exit from game
14
6. Troubleshooting
6.1 TV part
Failure
Cause and action
No power connection, or defective connection of
No picture, no sound
plug. Receiver is at standby mode.
Speaker for multimedia is not connected
Picture displayed without
properly.
sound
Volume is not turned on. Click Volume + button.
Chroma is not turned on. Adjust chroma option
under PICTURE menu.
No color
Program is of black and white color.
Picture system is set wrongly. Set picture system
correctly under PICTURE menu.
Monitor is not connected well.
Normal sound but no
Too strong interference in TV signal leads to
picture
protection state of monitor.
No picture or abnormal
Check if VGA cable is connected well and if PC
color of picture from PC
runs normally.
Remote control can’t be
Check if batteries are installed correctly.
operated or has low
Batteries are of weak power, or signal from
sensitivity.
remote control is obstructed or disturbed.
Signal from antenna is too weak. Add antenna
amplifier.
Snow spots or oblique line,
Defective connection of antenna, or the wire in
vertical line in picture
antenna cable is breaking off.
Failure of TV station.
6.2 PIP part
Failure
After PIP turned on,
sound is normal but no
picture display.
PIP invalid
Cause and action
Check if the output mode of display card in PC is
standard (see section 3).
Check if there is PC signal input.
6.3 PIP can function normally at the following PC display modes
Resolution
800X600
1024X768
1280X1024
1440X900
Refresh Rate
60Hz
60Hz
60Hz
60Hz
15
75Hz
75Hz
75Hz

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement