advertisement
OWNER’S MANUAL
IPS LED MONITOR
(LED LCD MONITOR)
Please read this manual carefully before operating your set and retain it for future reference.
IPS LED(LED LCD) MONITOR MODEL
19MB35PM
22MB35PM
23MB35PM
24MB35PM www.lg.com
2 TABLE OF CONTENTS
CONTENTS
ASSEMBLING AND PREPAR-
ING
- Using the Kensington locking device
USING THE MONITOR SET
12 - Peripheral device connection
CUSTOMIZING SETTINGS
TROUBLESHOOTING
SPECIFICATIONS
PROPER POSTURE
28 Proper posture for using the Monitor set.
ASSEMBLING AND PREPARING 3
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.
CD(Owner's Manual) /
Card
D-SUB Cable
(This cable is not included in all countries.)
DVI-D Cable
(This cable is not included in all countries.)
Power Cord
Stand Base
Audio Cable
( Depending on the country )
CAUTION y Do not use any unapproved accessories to ensure the safety and product life span.
y Any damages or injuries by using unapproved accessories are not covered by the warranty.
NOTE y The accessories supplied with your product may vary depending on the model.
y Product specifications or contents in this manual may be changed without prior notice due to upgrade of product functions.
4 ASSEMBLING AND PREPARING
Parts and buttons
Power Indicator y LED On : Power is on y LED Off: Power is off
(Power Button)
Front Side Buttons
Setting up the Monitor set
Attaching the Stand Base
1 Place the Monitor set with the screen side down on a flat and cushioned surface.
CAUTION y To protect the screen from scratches, cover the surface with a soft cloth.
ASSEMBLING AND PREPARING 5
Detaching the stand base
1 Place the monitor's screen face down.
To protect the screen from scratches, cover the surface with a soft cloth.
2 Detach the stand base from the stand body.
2 Check the position (at the front and rear) of the stand body, then mount the stand base on the stand body as shown in the figure.
Stand Base
Stand Body
CAUTION y The components appearing in the illustrations may look different from the actual product.
y Do not carry the monitor upside-down as this may cause it to fall off its stand, resulting in damage or injury.
y To avoid damaging the screen when lifting or moving the monitor, only hold the stand or the plastic cover. This avoids putting unnecessary pressure on the screen.
y Only remove the tape and the locking pin when the monitor is mounted on the stand base and is in an upright position. Otherwise, the stand body may protrude, which may lead to injury.
6 ASSEMBLING AND PREPARING
Detaching the stand body
1 Place the monitor's screen face down. To protect the screen from scratches, cover the surface with a soft cloth.
2 Using a screwdriver, remove the four screws and detach the stand from the monitor.
Mounting on a table
1 Lift the monitor and place it on the table in an upright position.
Install at least 10 cm away from the wall to ensure sufficient ventilation.
ASSEMBLING AND PREPARING 7
Adjusting the angle
1 Place the monitor mounted on the stand base in an upright position.
2 Adjust the angle of the screen. The angle of the screen can be adjusted up to 5° forwards and 20° backwards for a comfortable viewing experience.
10 cm
10 cm
10 cm
10 cm
Rear Side Front Side
2 Connect the Power cord to the monitor, then plug the power cord into the wall outlet.
WARNING y To avoid injury to the fingers when adjusting the screen, do not hold the lower part of the monitor's frame as illustrated below.
3 Press the (Power) button on the front of the monitor to turn on the monitor.
CAUTION y Unplug the power cord prior to moving or installing the monitor. There is risk of electric shock.
y Be careful not to touch or press the screen area when adjusting the angle of the monitor.
8 ASSEMBLING AND PREPARING
Adjusting the stand height
1 Place the monitor mounted on the stand base in an upright position.
2 Remove the tape attached at the bottom rear of the stand body, then pull out the locking
pin.
Stand Body
Tape
Locking Pin
Using the Kensington locking device
The connector for the Kensington lock is located on the rear of the monitor.
For more information on installation and usage, refer to the Kensington lock user manual or visit the website at http://www.kensington.com.
Connect the monitor to the table with the Kensington lock cable.
3 The height can be adjusted up to 110 mm.
110.0mm
CAUTION y Once the pin is removed, it is not necessary to re-insert it to adjust the height.
WARNING y Do not put your finger between the screen and the base (chassis) when adjusting the screen's height.
NOTE y Using the Kensington lock is optional. The accessories can be purchased at your local electronics store.
ASSEMBLING AND PREPARING 9
Swivel stand
y Image shown may differ from your Monitor set.
1 Swivel 355 degrees and adjust the angle of the
Monitor set to suit your view.
3 Be careful with the cables when rotating the screen.
Using the Pivot function
The pivot function allows you to rotate the screen
90 degrees clockwise.
1 Lift the monitor to its highest height to utilize the Pivot function.
2 Landscape & Portrait : You can rotate the panel
90° clockwise. Please be cautious and avoid contact between the monitor head and the
Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack.
Head section
Stand section
10 ASSEMBLING AND PREPARING
Mounting on a wall
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
10 cm
10 cm
10 cm
10 cm
If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set.
When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.
1 Please, Use the screw and wall mount interface in accordance with VESA Standards.
2 If you use screw longer than standard, the monitor might be damaged internally.
3 If you use improper screw, the product might be damaged and drop from mounted position. In this case, LG Electronics is not responsible for it.
4 VESA compatible.
5 Please use VESA standard as below.
y 784.8 mm (30.9 inch) and under
* Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x
Length 10 mm y 787.4 mm (31.0 inch) and above
* Please use VESA standard wall mount pad and screws.
Model 19MB35PM
23MB35PM
VESA (A x B) 75 x 75
Standard screw M4
Number of screws 4
22MB35PM
24MB35PM
100 x 100
CAUTION y Disconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur.
y If you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury. y Use only an authorized LG wall mount and contact the local dealer or qualified personnel.
y Do not over tighten the screws as this may cause damage to the Monitor set and void your warranty. y Use only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.
NOTE y Use the screws that are listed on the VESA standard screw specifications.
y The wall mount kit will include an installation manual and necessary parts.
y The wall mount bracket is optional. You can obtain additional accessories from your local dealer.
y The length of screws may differ depending on the wall mount. Be sure to use the proper length.
y For more information, refer to the instructions supplied with the wall mount.
USING THE MONITOR SET 11
USING THE MONITOR SET
Connecting to a PC
y Your Monitor set supports Plug & Play*.
*Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention.
D-SUB connection
Transmits analog video from your PC to the
Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations.
DVI-D connection
Transmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the following illustrations.
NOTE y When you want to use two PC in our Monitor, please connect the signal cable(D-SUB/
DVI-D) respectively in Monitor set.
y If you turn the Monitor set on while it is cold, the screen may flicker. This is normal.
y Some red, green, or blue spots may appear on the screen. This is normal.
NOTE y When using a D-Sub signal input cable connector for Macintosh y Mac adapter
For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector.
CAUTION y Connect the signal input cable and tighten it by turning the screws clockwise.
y Do not press the screen with your finger for a long time as this may result in temporary distortion on the screen.
y Avoid displaying a fixed image on the screen for a long period of time to prevent image burn. Use a screensaver if possible.
12 USING THE MONITOR SET
Peripheral device connection
Connect peripheral devices to the monitor using headphone ports.
Self Image Setting Function
Press the power button on the bottom panel to turn the power on. When monitor power is turned on, the " Self Image Setting " Function is executed automatically. (Only supported in Analog Mode)
NOTE y Peripheral devices are sold separately.
y Cables with angled plugs may have clearance issues, use straight plugs when possible.
NOTE y "Self Image Setting" Function.
This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.(Only supported in Analog Mode) y ‘AUTO’ Function.
When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the
AUTO function button to improve resolution.
(Only supported in Analog Mode)
Angle Type Straight Type
NOTE y Headphones or speakers may not work normally, depending on the server PC settings.
CUSTOMIZING SETTINGS 13
CUSTOMIZING SETTINGS
1 Press the desired button on the bottom of the Monitor set.
2 Change the value of the menu item by pressing the buttons on the bottom of the Monitor set.
To return to the upper menu or set other menu items, use the up arrow ( ) button.
3 Select EXIT to leave the OSD menu.
Button
(Power Button)
Monitor set Buttons
Description
Accesses the main menus.(See p.14)
OSD Locked/OSD
Unlocked
This function allow you to lock the current control settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds. Then
OSD of “OSD Lock” will appear. After that, user can select lock or unlock by pressing left/right button.
If user selects the “Lock” icon by pressing the “OK” button, the message “OSD Locked” will appear. Otherwise, “OSD
Unlocked” will appear. After selecting the “Lock”, If you want to change to Unlock, you can push the “MENU” button for several seconds. The message “OSD Unlocked” will appear.
Use this button to enter Reader Mode menu. Its function works to display screen as paper-like picture for Eye comfort.If you want to more information.(See p.19)
Use this button to enter SUPER ENERGY SAVING menu.
( See p.20
)
When adjusting your display settings, always press the AUTO button on the MONITOR
SETUP OSD. (Only supported in Analog Mode)
The best display mode 19MB35PM:1280 x 1024
22MB35PM/23MB35PM/24MB35PM:1920 x 1080
You can choose the input signal.
• When two input signals are connected, you can select the input signal (D-SUB/DVI) you want.
• When only one signal is connected, it is automatically detected. The default setting is
D-SUB.
EXIT
Exit the OSD(On Screen Display).
Turns the power on or off.
Power Indicator The power indicator stays white if the display is running properly (On Mode). If the display is in Sleep Mode, the power indicator blinks white.
14 CUSTOMIZING SETTINGS
Customizing Settings
Menu Settings
1 Press MENU button on the bottom of the Monitor set to display the Menu OSD.
2 Set the options by pressing the ◄ or ► or ▼ buttons.
3 Select the " Next Menu" button to enter the more option settings.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the up arrow ( ) button.
Each option is explained below.
Menu Analog Digital
Volume
Brightness
Response
Time
(only for
19MB35PM,
23MB35PM,
24MB35PM)
Wide/
Original
●
●
●
●
●
●
To adjust the volume
Description
To adjust the brightness of the screen
You can set a response time for displayed pictures based on the speed of the screen. For a normal environment, it is recommended that you use 'Off'. For a fastmoving picture, it is recommended that you use 'High'.
Wide
Switch to full screen mode according to input image signal.
● ● Original
Reset ● ●
Change the input image signal ratio to original.
* This function works only if input resolution is lower than Monitor set ratio (16:9).
Restore all factory default settings. Press the ◄ , ► buttons to reset immediately.
Menu > Next Menu
Picture Contrast
Color
Sharpness
Gamma
Color Temp
Six Color (only for 19MB35PM,
23MB35PM,
24MB35PM)
Color Reset (only for 19MB35PM,
23MB35PM,
24MB35PM)
Display Horizontal
Vertical
Clock
Phase
Others Language
Power Indicator
Off Time Setting
Analog Digital
● ●
● ●
Description
To adjust the contrast of the screen
To adjust the clearness of the screen
●
●
●
●
●
●
●
●
To customize the color of the screen
To adjust the position of the screen
To improve the clarity and stability of the screen
To customize the screen status for a user's operating environment y Analog: D-SUB(Analog signal) input.
y Digital: DVI-D(Digital signal) input.
Picture
1 Press MENU button on the bottom of the Monitor set to display the Menu OSD.
2 Select the " Next Menu" button to enter the more option settings.
3 Enter to Picture by pressing the ▼ button.
4 Set the options by pressing the ◄ or ► or ▼ buttons.
5 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the up arrow ( ) button.
Each option is explained below.
Menu > Next Menu > Picture
Contrast
Sharpness
Description
To adjust the contrast of the screen.
To adjust the clearness of the screen.
CUSTOMIZING SETTINGS 15
16 CUSTOMIZING SETTINGS
Color
1 Press MENU button on the bottom of the Monitor set to display the Menu OSD.
2 Select the " Next Menu" button to enter the more option settings.
3 Select Color by pressing the ► button.
4 Enter to Color by pressing the ▼ button.
5 Set the options by pressing the ◄ or ► or ▼ buttons.
6 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the up arrow ( ) button.
Each option is explained below.
Menu > Next Menu > Color
Gamma
Color Temp
Six Color
(only for 19MB35PM, 23MB35PM,
24MB35PM)
Color Reset
(only for 19MB35PM, 23MB35PM,
24MB35PM)
Description
Set your own gamma value. : Gamma 0, Gamma 1, Gamma 2 on the monitor, high gamma values display whitish images and low gamma values display blackish images.
Custom
• Red:Set your own red color levels.
• Green: Set your own green color levels.
• Blue:Set your own blue color levels.
Select the screen color.
Warm: Set the screen to warm color temperature (more red).
Medium: Set the screen to medium color temperature.
Cool: Set the screen to cool color temperature (more blue).
Sets and stores the hue and saturation for six colors(Red/Green/Blue/Cyan/
Magenta/Yellow) to satisfy the color requirements of a user.
Hue
Saturation
Adjusts the screen hue.
Adjusts the color sharpness on the screen. Lower values make the color sharpness weaker and colors lighter while higher values make the color sharpness stronger and colors dark.
Resets the color settings to the factory default settings for the current input device.
CUSTOMIZING SETTINGS 17
Display
1 Press MENU button on the bottom of the Monitor set to display the Menu OSD.
2 Select the " Next Menu" button to enter the more option settings.
3 Select Display by pressing the ► button.
4 Enter to Display by pressing the ▼ button.
5 Set the options by pressing the ◄ or ► or ▼ buttons.
6 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the up arrow ( ) button.
Each option is explained below.
Menu > Next Menu > Display
Horizontal
Vertical
Clock
Phase
Description
To move image left and right.
To move image up and down.
To minimize any vertical bars or stripes visible on the screen background.The horizontal screen size will also change.
To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters.
18 CUSTOMIZING SETTINGS
Others
1 Press MENU button on the bottom of the Monitor set to display the Menu OSD.
2 Select the " Next Menu" button to enter the more option settings.
3 Select Others by pressing the ► button.
4 Enter to Others by pressing the ▼ button.
5 Set the options by pressing the ◄ or ► or ▼ buttons.
6 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the up arrow ( ) button.
Each option is explained below.
Menu > Next Menu > Others
Language
Power Indicator
Off Time Setting
Description
To choose the language in which the control names are displayed.
Use this function to set the power indicator on the bottom side of the monitor to
On or Off.If you set Off, it will go off.
If you set On at any time, the power indicator will automatically be turned on.
The monitor set will switch to power off mode after the time to be chosen by user
(1 ~ 24 hours)
CUSTOMIZING SETTINGS 19
READER Setting
1 Press READER button on the bottom of the Monitor set to display the Reader Mode OSD.
2 Set the options by pressing the ◄ buttons.
Each option is explained below.
Reader 1
Reader Mode
Reader 2
Reader Off
Description
It is a mode that the screen is adjusted to the best for the newspaper. If you want screen more bright, you can control brightness in Menu OSD.
It is a mode that the screen is adjusted to the best for the cartoon. If you want screen more bright, you can control brightness in Menu OSD.
It is a mode that reader mode is off.
NOTE
If option of Reader Mode is Reader 1 or Reader 2, Picture Mode will automatically be Custom and
Super Energy Saving will automatically be Off.
20 CUSTOMIZING SETTINGS
SUPER ENERGY SAVING
1 Press button on the bottom of the Monitor set to display the SUPER ENERGY SAVING OSD.
2 Set the options by pressing the ► buttons.
Each option is explained below.
SUPER ENERGY SAVING
High
Low
Off
Description
Enables SUPER ENERGY SAVING you can save energy with this energy- high efficient function.
Enables SUPER ENERGY SAVING you can save energy with this energy- low efficient function.
Disables SUPER ENERGY SAVING.
NOTE y TOTAL POWER REDUCTION: How much power is saved while using the monitor.
y TOTAL CO2 REDUCTION: Change the TOTAL POWER REDUCTION to CO2.
y SAVING DATA(W/h)
482 mm
(19 inch)
546 mm
(21.5 inch)
584 mm
(23 inch)
604 mm
(23.8 inch)
SUPER SAVING (High)
SUPER SAVING (Low)
3 W/h
1 W/h
4 W/h
2 W/h
4 W/h
2 W/h
4 W/h
2 W/h y Saving Data depends on the Panel. So,those values should be different from each panel and panel vendor.If option of Super Energy Saving is High or Low, monitor luminance become higher or lower depend on source.
y LG calculated these values by using “broadcast video signal”
(including broadcast video: IEC 62087) y SUPER SAVING refers to how much power can be saved using the SUPER ENERGY SAVING function.
y If option of Super Energy Saving is High or Low, Picture Mode will automatically be Custom and
Reader Mode will automatically be Reader Off.
TROUBLESHOOTING 21
TROUBLESHOOTING
Check the following before calling for service.
No image appears
Is the power cord of the display connected?
Is the power indicator light on?
Is the power on and the power indicator White?
Is the power indicator flickering?
y Check and see if the power cord is connected properly to the power outlet.
y Press the Power button.
y Adjust the brightness and the contrast.
Do you see an "OUT OF RANGE" message on the screen?
Do you see a "NO SIGNAL" message on the screen? y If the display is in power saving mode, try moving the mouse or pressing any key on the keyboard to bring up the screen.
y Try to turn on the PC.
y This message appears when the signal from the PC (video card) is out of horizontal or vertical frequency range of the display. See the
'Specifications' section of this manual and configure your display again.
y When the monitor is on "No-Signal" in 5 minutes, the monitor goes to
DPM mode.
Do you see a "OSD LOCKED" message on the screen?
Do you see “OSD LOCKED” when you push MENU button?
y You can secure the current control settings, so that they cannot be inadvertently changed. You can unlock the OSD controls at any time by pushing the MENU button for several seconds: the message “OSD
UNLOCKED” will appear.
Display image is incorrect
Display Position is incorrect.
On the screen background, vertical bars or stripes are visible.
Any horizontal noise appearing in any image or characters are not clearly portrayed.
y Press the AUTO button to automatically adjust your display image to the ideal setting.
y Press the AUTO button to automatically adjust your display image to the ideal setting. y Press the AUTO button to automatically adjust your display image to the ideal setting. y Check Control Panel ► Display ► Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. Set the color setting higher than 24 bits (true color).
22 TROUBLESHOOTING
CAUTION y Check Control Panel ► Display ► Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution.
y If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. Make sure to select the recommend resolution.
y The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer.
Display image is incorrect
The screen color is mono or abnormal.
The screen blinks.
y Check if the signal cable is properly connected and use a screwdriver to fasten if necessary.
y Make sure the video card is properly inserted in the slot.
y Set the color setting higher than 24 bits (true color) at
► Settings.
Control Panel y Check if the screen is set to interlace mode and if yes, change it to the recommend resolution.
Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message?
Have you installed the display driver?
y Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driver from our web site: http://www.lg.com.
y Make sure to check if the video card supports Plug&Play function.
SPECIFICATIONS 23
SPECIFICATIONS
19MB35PM
Display Screen Type 48.2 cm (19 inch) Flat Panel Active matrix-TFT LCDAnti-
Glare coating
Visible diagonal size: 48.2 cm
Sync Input
Video Input
Resolution
Pixel Pitch
Input Form
Max
0.294 mm x 0.294 mm (Pixel Pitch)
Horizontal Frequency 30 kHz to 83 kHz (Automatic)
Vertical Frequency 56Hz to 75Hz (D-SUB,DVI-D)
Input Form
Signal Input
Separate Sync. Digital
15 pin D-SUB Connector /DVI-D Connector (Digital)
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
D-SUB(Analog) : 1280 x 1024 @ 60 Hz
DVI (Digital) : 1280 x 1024 @ 60 Hz
Plug & Play
Power
Consumption
Recommend
DDC 2B(Analog,Digital)
Power Input
Speaker Wattage 1 W +1 W
With Stand
(Width x Height x
Depth)
Without Stand
Weight 3.8 kg
Tilt Range -5° to 20°
VESA 1280 x 1024 @ 60 Hz
On Mode : 15 W (ENERGY STAR® standard)*
Sleep Mode ≤ 0.3 W
Off Mode ≤ 0.3 W
AC 100-240V ~ 50/60Hz 0.8 A
40.9 cm x 48.1 cm x 21.0 cm
40.9 cm x 33.8 cm x 5.8 cm
10°C to 35 °C
10 % to 80 %
Stand Base
Power cord
Storage Temperature
Storage Humidity
-20°C to 60 °C
5 % to 90 % non-Condensing
Attached ( ), Detached (O)
Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product functions.
* The power consumption level can be different by operating condition and monitor setting.
* The On mode power consumption is measured with ENERGY STAR® test standard.
* ENERGY STAR® is a US registered mark of the United States Environmental Protection Agency.
24 SPECIFICATIONS
SPECIFICATIONS
22MB35PM
Display Screen Type 54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCDAnti-
Glare coating
Visible diagonal size: 54.6 cm
Sync Input
Video Input
Resolution
Pixel Pitch 0.248 mm x 0.248 mm (Pixel Pitch)
Horizontal Frequency 30 kHz to 83 kHz (Automatic)
Vertical Frequency
Input Form
56Hz to 75Hz (D-SUB,DVI-D)
Separate Sync. Digital
Signal Input
Input Form
Max
Recommend
DDC 2B(Analog,Digital)
15 pin D-SUB Connector /DVI-D Connector (Digital)
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
D-SUB(Analog) : 1920 x 1080 @ 60 Hz
DVI (Digital) : 1920 x 1080 @ 60 Hz
VESA 1920 x 1080 @ 60 Hz
Plug & Play
Power
Consumption
Power Input AC 100-240V ~ 50/60Hz 1.0 A
Speaker Wattage 1 W +1 W
Dimensions
Depth)
Weight
With Stand
Without Stand
3.9 kg
50.9 cm x 35.3 cm x 22.4 cm
50.9 cm x 30.4 cm x 14.4 cm
Tilt Range
Environmental conditions
On Mode : 20 W (ENERGY STAR® standard)*
Sleep Mode ≤ 0.3 W
Off Mode ≤ 0.3 W
-5° to 20°
Operating Temperature
Operating Humidity
10°C to 35 °C
10 % to 80 %
-20°C to 60 °C
5 % to 90 % non-Condensing
Stand Base
Power cord
Attached ( ), Detached (O)
Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product functions.
* The power consumption level can be different by operating condition and monitor setting.
* The On mode power consumption is measured with ENERGY STAR® test standard.
* ENERGY STAR® is a US registered mark of the United States Environmental Protection Agency.
SPECIFICATIONS 25
SPECIFICATIONS
23MB35PM
Display Screen Type 58.4 cm (23 inch) Flat Panel Active matrix-TFT LCDAnti-
Glare coating
Visible diagonal size: 58.4 cm
Sync Input
Video Input
Resolution
Pixel Pitch 0.2652 mm x 0.2652 mm (Pixel Pitch)
Horizontal Frequency 30 kHz to 83 kHz (Automatic)
Vertical Frequency
Input Form
Signal Input
Input Form
Max
56Hz to 75Hz (D-SUB,DVI-D)
Separate Sync. Digital
15 pin D-SUB Connector /DVI-D Connector (Digital)
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
D-SUB(Analog) : 1920 x 1080 @ 60 Hz
DVI (Digital) : 1920 x 1080 @ 60 Hz
Plug & Play
Recommend
DDC 2B(Analog,Digital)
VESA 1920 x 1080 @ 60 Hz
On Mode : 21 W (ENERGY STAR® standard)*
Sleep Mode ≤ 0.3 W
Off Mode ≤ 0.3 W
Power Input AC 100-240V ~ 50/60Hz 1.0 A
Speaker Wattage 1 W +1 W
(Width x Height x
Depth)
Weight
Tilt Range
With Stand
Without Stand
4.5 kg
-5° to 20°
54.8 cm x 36.7 cm x 24.6 cm
54.8 cm x 33.5 cm x 16.6 cm
10°C to 35 °C
10 % to 80 %
Stand Base
Power cord
-20°C to 60 °C
5 % to 90 % non-Condensing
Attached ( ), Detached (O)
Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product functions.
* The power consumption level can be different by operating condition and monitor setting.
* The On mode power consumption is measured with ENERGY STAR® test standard.
* ENERGY STAR® is a US registered mark of the United States Environmental Protection Agency.
26 SPECIFICATIONS
SPECIFICATIONS
24MB35PM
Display Screen Type 60.4 cm (23.8 inch) Flat Panel Active matrix-TFT LCDAnti-
Glare coating
Visible diagonal size: 60.4 cm
Sync Input
Video Input
Resolution
Plug & Play
Power
Consumption
Pixel Pitch 0.275 mm x 0.275 mm (Pixel Pitch)
Horizontal Frequency 30 kHz to 83 kHz (Automatic)
Vertical Frequency 56Hz to 75Hz (D-SUB,DVI-D)
Input Form
Signal Input
Separate Sync. Digital
15 pin D-SUB Connector /DVI-D Connector (Digital)
Input Form
Max
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
D-SUB(Analog) : 1920 x 1080 @ 60 Hz
DVI (Digital) : 1920 x 1080 @ 60 Hz
VESA 1920 x 1080 @ 60 Hz Recommend
DDC 2B(Analog,Digital)
On Mode : 23 W (ENERGY STAR® standard)*
Sleep Mode ≤ 0.3 W
Off Mode ≤ 0.3 W
Power Input
Tilt Range
AC 100-240V ~ 50/60Hz 1.2 A
Speaker Wattage 1 W +1 W
With Stand
(Width x Height x
Depth)
Without Stand
Weight 5.1 kg
-5° to 20°
56.9 cm x 43.2 cm x 27.1 cm
56.9 cm x 34.2 cm x 6.3 cm
10°C to 35 °C
10 % to 80 %
Stand Base
Power cord
Storage Temperature
Storage Humidity
-20°C to 60 °C
5 % to 90 % non-Condensing
Attached ( ), Detached (O)
Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product functions.
* The power consumption level can be different by operating condition and monitor setting.
* The On mode power consumption is measured with ENERGY STAR® test standard.
* ENERGY STAR® is a US registered mark of the United States Environmental Protection Agency.
SPECIFICATIONS 27
Preset Modes (Resolution)
19MB35PM
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
31.468
31.469
37.500
37.879
46.875
48.363
60.023
67.500
63.981
79.976
75
60
75
60
Vertical
Frequency(Hz)
70
60
75
75
60
75
Polarity(H/V)
+/+
-/-
-/-
+/+
-/+
-/-
-/-
+/+
+/+
+/+ Recommend Mode
22MB35PM 23MB35PM 24MB35PM
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1680 x 1050
1920 x 1080
31.468
31.469
37.500
37.879
46.875
48.363
60.023
67.500
63.981
79.976
65.290
67.500
60
75
60
60
75
60
75
60
Vertical
Frequency(Hz)
70
60
75
75
Polarity(H/V)
+/+
+/+
-/+
+/+
+/+
-/-
+/+
+/+
-/+
-/-
-/-
+/+
Recommend Mode
Indicator
Mode
On Mode
Sleep Mode
Off Mode
LED Color
White
Blinking White
Off
28 PROPER POSTURE
PROPER POSTURE
Proper posture for using the Monitor set.
Adjust the
Monitor set and your posture to allow you to view images at the optimal viewing angle.
Adjust the location of the
Monitor set to avoid it reflecting light.
Place your hands gently on the keyboard, keeping your arms bent at the elbows and horizontally outright.
Declaration of Conformity
Trade Name: LG
Model : 19MB35PMF,22MB35PMF,23MB35PMF,
24MB35PMF
Responsible Party: LG Electronics Inc.
Address : 1000 Sylvan Ave. Englewood Cliffs
NJ 07632 U.S.A
TEL: 201-266-2534
*above information is only for USA FCC Regulatory
Make sure to read the Safety Precautions before using the product.
Keep the Owner’s Manual (CD) in an accessible place for future reference.
The model and serial number of the SET is located on the back and one side of the SET.
Record it below should you ever need service.
MODEL
SERIAL
ENERGY STAR is a set of power-saving guidelines issued by the U.S.Environmental
Protection Agency(EPA).
As an ENERGY STAR Partner LGE
U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- 60.5 cm (23.8") LED IPS
- Full HD 1920 x 1080 pixels 16:9
- 5 ms 250 cd/m² 1000:1
- 24 W
