null User manual

null  User manual
D-Link AirPlus DWL-650+
2.4 GHz Wireless Cardbus Adapter
Manual
Building Networks for People
Contents
1.
Package Contents ....................................................... 3
2.
Introduction .................................................................. 4
3.
Wireless Basics ........................................................... 6
4.
Getting Started............................................................. 9
5.
Installing the DWL-650+ ............................................ 12
6.
Using the Configuration Utility ................................... 15
7.
Troubleshooting ......................................................... 22
8.
Networking Basics ..................................................... 26
9.
Technical Specifications............................................. 54
10. Contacting Technical Support ..................................... 56
11. Limited Warranty and Registration .............................. 57
2
1.
Package Contents
Contents of Package:
•
D-Link AirPlus DWL-650+ 2.4GHz Wireless Cardbus Adapter
•
Manual, QIG, and Drivers on CD
•
Printed Quick Installation Guide
If any of the above items are missing, please contact your reseller.
System Requirements:
•
A laptop computer with an available 32-bit Cardbus PC Card slot
•
Windows XP, Windows 2000, Windows Me, or Windows 98
•
Cardbus Controller, properly installed and working
•
At least 32 MB of memory and a 300 MHz processor
•
An 802.11b Access Point (e.g., DWL-900AP+ for Infrastructure
Mode) or another 802.11b wireless adapter (e.g., DWL-520 for AdHoc mode.)
3
2. Introduction
The D-Link AirPlus DWL-650+ Wireless Cardbus Adapter is an enhanced
802.11b high-performance, wireless adapter that supports high-speed
wireless networking at home, at work or in public places.
Unlike most 802.11b network cards, the DWL-650+ provides speeds of up to
22 Mbps (compared to the standard 11 Mbps) when used with other D-Link
AirPlus products such as the DWL-520+ Wireless PCI Adapter.
Now increased speed is available when you enable the new 4x feature
(when used with the 4x-enabled DI-614+ Wireless Broadband Router or the
4x-enabled DWL-900AP+ Wireless Access Point.)
The DWL-650+ is also compatible with existing 802.11b devices such as the
D-Link AirPlus family of products including the DWL-520+ Wireless PCI
Adapter, the DWL-900AP+ Wireless Access Point and the DI-614+ Wireless
Broadband Router.
Extra security is provided by the addition of 802.1x* support. With 802.1x
compatible routers and access points along with a radius server, the DWL650+ will participate in a much more secure network (that includes client
authentication) than is available with WEP encryption alone.
It is an ideal way to connect one laptop computer to a Wireless Local Area
Network (WLAN.) After completing the steps outlined in the Quick
Installation Guide (included in the package) you will have the ability to
share information and resources, such as files and printers, and take full
advantage of a “connected” environment for work or play!
The DWL-650+ includes software drivers for the most popular Microsoft
Windows operating systems (Windows XP, Windows 2000, Windows Me,
Windows 98) and can be integrated into a larger network, running, in either
Ad Hoc mode (without an Access Point) or Infrastructure mode (with an
Access Point.) Please take a look at our Getting Started section in this
manual to see examples of typical network setups using the DWL-650+ in
both Infrastructure and Ad-Hoc modes.
This manual provides a quick introduction to wireless technology and its
application as it relates to networking. Take a moment to read through this
manual and get acquainted with wireless technology.
* 802.1x Authentication requires EAP (Extensible Authentication Protocol.) 802.1x supported EAP is
available through the Windows XP Operating System. You will need to use the same type of EAP protocol
on all the devices in your network when using the 802.1x feature.
4
Features and Benefits
•
•
•
•
Supports 802.1x authentication security
Now even faster performance with the new 4x feature, when used
with 4x-enabled DI-614+ or 4x-enabled DWL-900AP+
Speeds up to 2x faster, with data transfer rates up to 22Mbps, when
used with other D-Link AirPlus products
Operates in the 2.4GHz frequency range
•
Maximum reliability, throughput and connectivity with automatic data
rate switching
•
Supports Wired Equivalent Privacy (WEP) data encryption at
64/128/256-bit encryption
•
Supports infrastructure networks via an Access Point and peer-topeer communication in ad-hoc mode
•
Built-in dual diversity antenna for reduced interference in a multi-path
environment
•
32-bit Cardbus Performance
•
User-friendly configuration and diagnostic utilities
LEDs
LED stands for Light-Emitting Diode. The DWL-650+ has two LEDs:
1. Power - Green LED lights on steady to indicate a proper connection
to a power source.
2. Link -
Green LED flashes to indicate activity on the network
and lights on steady to indicate that a link to the network is
established.
Link
Power
5
3.
Wireless Basics
D-Link AirPlus wireless products are based on industry standards to provide
easy-to-use and compatible high-speed wireless connectivity within your
home, business or wherever a wireless network is available. Strictly adhering
to the IEEE standard, the D-Link AirPlus wireless family of products will allow
you to access the data you want, when and where you want it. No longer will
you be limited to one location or forced to run new wiring through your home
or office. You will be able to enjoy the freedom that wireless networking
delivers.
A wireless local area network (WLAN) is a cellular computer network that
transmits and receives data with radio signals instead of wires. Wireless
LANs are used increasingly in both home and office environments, and
public areas such as airports, coffee shops and universities. Innovative ways
to utilize WLAN technology are helping people to work and communicate
more efficiently. Increased mobility with the absence of cabling and other
fixed infrastructure have proven to be beneficial for many users.
Wireless users can use the same applications they use on a wired network.
Wireless adapter cards used on laptop and desktop systems, support the
same protocols as Ethernet adapter cards. For most users, there is no
noticeable functional difference between a wired Ethernet desktop computer
and a wireless computer equipped with a wireless adapter other than the
added benefit of the ability to roam within a wireless-cell. Under many
circumstances, it may be desirable for mobile network devices to link to a
conventional Ethernet LAN in order to use servers, printers or an Internet
connection supplied through the wired LAN. A Wireless Access Point (AP) is
a device used to provide this link.
People use wireless LAN technology for many different purposes.
Mobility - Productivity increases when people have access to data in any
location within the operating range of the WLAN. Management decisions
based on real-time information can significantly improve worker efficiency.
Low Implementation Costs – WLANs (Wireless Local Area Networks) are
easy to set up, manage, change and relocate. Networks that frequently
change, both physically and logically, can benefit from WLANs ease of
implementation. WLANs can operate in locations where installation of wiring
may be impractical.
Installation Speed and Simplicity - Installing a wireless LAN system can
be fast and easy and can eliminate the need to install cable through walls
and ceilings.
6
Wireless Basics
Network Expansion - Wireless technology allows the network to go where
wires cannot go.
Reduced Cost-of-Ownership - While the initial investment required for
Wireless LAN hardware might be higher than the cost of wired LAN
hardware, overall installation expenses and life-cycle costs will be
significantly lower. Long-term cost benefits are greatest in dynamic
environments requiring frequent moves, adds, and changes.
Scalability - Wireless Local Area Networks (WLANs) can be configured in a
variety of topologies to meet the needs of specific applications and
installations. Configurations are easily changed and range from peer-to-peer
networks suitable for a small number of users to full infrastructure networks
of thousands of users that allow roaming over a broad area.
Some D-Link devices that are compatible with the D-Link DWL-650+ are:
D-Link DWL-520+ 2.4GHz Wireless PCI cards used with desktop
computers
D-Link DI-614+ Wireless Broadband Router
D-Link DWL-900AP+ Wireless Access Point
Standards - Based Technology
The IEEE standard-based technology assures that the D-Link AirPlus
Products are interoperable with existing compatible 2.4GHz wireless
technology. This means you will be able to transfer large files quickly or
even watch a movie in MPEG format over your network without noticeable
delays. The technology works by using multiple frequencies in the 2.4GHz
range at speeds up to 22Mbps. D-Link AirPlus products will automatically
sense the best possible connection speed to ensure the greatest speed and
range possible with the technology.
802.1x provides an extra level of security to your wireless network. Through
its Authentication protocol (when 802.1x is activated), only clients with
802.1x authentication will be permitted to communicate in your network; all
other clients will be denied access. This is a far more secure wireless
network than has previously been available.
All devices on the network must be 802.1x compatible and must share the
same EAP type. For Authentication purposes you will need a radius server
in your network.
7
Installation Considerations
Designed to go up to 1,312 feet (400 meters) outdoors and up to 328 feet
(100 meters) indoors, the D-Link AirPlus DWL-650+ lets you access your
network with your laptop computer from virtually anywhere. Keep in mind,
however, that the number, thickness and location of walls, ceilings or other
objects that the wireless signal must pass thru may limit range. Typical
ranges vary depending on the types of materials and any background RF
(radio frequency) noise in your home or business. The key to maximizing
range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the wireless Access
Point and your receiving device (i.e., the DWL-650+) to a minimum Each wall or ceiling can reduce your D-Link AirPlus Wireless product’s
range from 3-90 feet (1-30 meters.) Position your Access Points,
Residential Gateways, and computers so that the number of walls or
ceilings is minimized.
2. Be aware of the direct line between Access Points, Residential
Gateways (routers), and computers. A wall that is 1.5 feet thick (.5
meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick.
At a 2-degree angle it looks over 42 feet (14 meters) thick! Try to make
sure that the Access Points and Adapters are positioned so that the
signal will travel straight through a wall or ceiling for better reception.
3. Building Materials make a difference - A solid metal door or aluminum
studs may have a negative effect on range. Try to position Access Points,
and computers with wireless adapters so that the signal passes through
drywall or open doorways and not other materials.
4. Make sure that the device’s antenna is positioned for best reception by
using the software signal strength tools included with your product.
5. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical
devices or appliances that may generate extreme RF noise.
8
Wireless Basics
For the average home, signal range should not be an issue. If you
experience low or no signal strength in areas of your home that you wish to
access, consider positioning the Access Point in a location directly between
the computers with wireless adapters. Additional Access Points can be
connected to provide better coverage in rooms where the signal does not
appear as strong as desired.
Using radio frequency (RF) technology, WLANs (Wireless Local Area
Networks) transmit and receive data over the air, minimizing the need for
wired connections. Thus, WLANs combine data connectivity with user
mobility, and, through simplified configuration, enable movable LANs.
4.
Getting Started
Right out of the box, with its default settings, the DWL-650+ will
automatically connect with other D-Link Air or AirPlus products.
For the price of a single IP Address from your Broadband Internet Service
provider you can share the Internet with all the computers on your local
network, without sacrificing speed or security, using D-Link AirPlus
networking products.
There are basically two modes of networking:
Infrastructure – using a Router/ Access Point, such as the DWL-900AP+
Ad-Hoc – directly connecting to another computer, for peer-to-peer
communication, using wireless network adapters on each computer, such
as two or more DWL-650+ Cardbus adapters.
On the following pages we will show you an example of an Infrastructure
Network and an Ad-Hoc Network.
An Infrastructure network contains an Access Point/Router.
The Infrastructure Network example shown on the following page contains
the following D-Link network devices:
A wireless Broadband Router A laptop computer with a wireless network adapter A desktop computer with a wireless network adapter A Cable modem -
D-Link Air DI-614+
D-Link AirPlus DWL-650+
D-Link AirPlus DWL-520+
D-Link DCM-201
DHCP stands for Dynamic Host Configuration Protocol. It is a protocol for assigning IP
Addresses “automatically.” With a DHCP-capable gateway/router, there is no need to
manually assign an IP Address.
9
Getting Started
Setting Up an Infrastructure Network
Please remember that D-Link AirPlus wireless devices are pre-configured to
connect together, right out of the box, with the default settings.
You will need a broadband Internet access (Cable/DSL)
subscription.
Consult with your Cable/DSL provider for proper installation of the
modem.
Connect the modem to a wireless Broadband router (the D-Link
DI-614+.) See the Quick Installation Guide included with the router.
Install the drivers for the DWL-520+ wireless network adapter into
the desktop computer. See the Quick Installation Guide included
with the adapter.
Install the drivers for the D-Link AirPlus DWL-650+ wireless
network adapter into the laptop computer. See the Quick
Installation Guide included with the DWL-650+.
If you are using the 802.1x protocol in your network, your setup may be different
than that pictured above. Please refer to the manual that came with your D-Link
802.1x compatible router or access point for further tips on setting up a more secure
network.
10
Getting Started
Setting up a Wireless Ad Hoc Network
Install the D-Link AirPlus DWL-520+ wireless network adapter into
the desktop computer. See the Quick Installation Guide included with
the product for installation instructions.
Install the DWL-650+ into a laptop computer. See the Quick
Installation Guide included with the product.
Set the wireless configuration for the adapters to Ad-Hoc mode,
set the adapters to the same channel, and assign an IP Address
to each computer on the Ad-Hoc network. (See Box below)
IP Address
When assigning IP Addresses to the computers on the network, please
remember that the IP Address for each computer must be in the same IP
Address range as all the computers in the network, and the subnet mask
must be exactly the same for all the computers in the network.
For example: If the first computer is assigned an IP Address of 192.168.0.2
with a Subnet Mask of 255.255.255.0, then the second computer can be
assigned an IP Address of 192.168.0.3 with a Subnet Mask of
255.255.255.0, etc.
IMPORTANT: If computers or other devices are assigned the same IP
Address, one or more of the devices may not be visible on the network.
11
5. Installing the DWL-650+
Installing the DWL-650+ Drivers & Utility
NOTE: Do not insert the DWL-650+ Cardbus into the Cardbus slot at
this point. You will be instructed in Section 2 to install the DWL-650+
Cardbus adapter.
Windows XP, 2000, Me, or 98 Installation:
The following screen shots are taken from Windows XP. Windows 2000, Me,
and 98 will have a similar screenshots for installing the drivers.
•
Turn on the laptop computer.
•
Insert the D-Link AirPlus DWL-650+ Driver CD into the CD-ROM
Drive.
•
Click on the Install Driver/PC Utility bullet point on the installation
screen.
12
Installing the DWL-650+
Drivers and Utility
If the AutoRun function on your laptop computer does not automatically start,
proceed to the steps below. If it does, proceed to Section 2.
•
Go to Start > Run > type
D:\Setup.exe
•
Click OK
NOTE: The letter “D” represents
the letter of the CD-ROM drive.
Your CD-ROM drive may be a
different drive letter.
Fig. 5.1.2 Windows XP setup screen.
The Windows 2000, Me, and 98 screen
will look similar to Fig 5.1.2.
Installing the Drivers and Utility (continued…)
Welcome to the InstallShield Wizard for
D-Link AirPlus DWL-650+ Utility and Driver.
The InstallShield Wizard will install D-Link
AirPlus DWL-650+ Utility and Driver on your
computer. To continue, click Next.
•
Click Next
Fig. 5.2.1
Setup will install D-Link AirPlus DWL-650+ Utility and Driver in the following folder.
•
Click Next to install the Utility
program in the default folder.
13
Fig. 5.2.2
Installing the DWL-650+
Drivers and Utility
The InstallShield Wizard has successfully
installed D-Link AirPlus DWL-650+ Utility and
Driver. Before you can use the program, you
must restart your computer.
• Select No, I will restart my
computer later.
• Click Finish
Fig. 5.2.3
• Shut down your laptop computer.
• Insert the DWL-650+ into the Cardbus slot.
• Restart your laptop computer
• Click Next at the Welcome
screen (Fig. 5.2.4)
For Windows XP, Fig.
5.2.5 may appear after the
laptop computer restarts.
Click Continue Anyway
to finalize the installation.
(This device has been
successfully tested to
work on Windows XP,
as well as Windows 2000,
Windows Me and
Windows 98.
Microsoft certification is
pending.)
Fig. 5.2.4
D-Link AirPlus DWL-650+ Wireless Cardbus Adapter
Fig. 5.2.5
14
Installing the DWL-650+
For Windows 2000, Fig. 5.2.6 may appear
after the laptop computer restarts. Select Yes
to finalize the installation.
D-Link AirPlus DWL-650+ Wireless Cardbus Adapter
Fig. 5.2.6
Click Finish to complete the
installation.
For Windows Me and 98, after the laptop
computer restarts, it will ask you to reboot the
computer once more to finalize the driver
installation. Select Yes to finalize the
installation.
Fig. 5.2.7
Fig. 5.2.8
YOU HAVE COMPLETED THE INSTALLATION OF THE DRIVERS. SEE
NETWORKING BASICS IN THIS MANUAL FOR INFORMATION ON
SETTING UP YOUR NETWORK.
6.
Using the Configuration Utility
If you want to alter the default settings or optimize the performance of the
DWL-650+, D-Link has included a configuration utility to do so.
Note: Out of the box, with its default settings, the DWL-650+ will associate with
D-Link AirPlus wireless routers (e.g., DI-614+) and access points (e.g., DWL900AP+).
After the computer restarts, the configuration utility will automatically start
and the utility icon will appear in the bottom right hand corner of the screen
(systray).
• Double-click on the Configuration Utility icon
Fig. 6.1
(Fig. 6.1) shown on the right.
Note: If the utility icon does not appear, double-click on the shortcut icon
(Fig. 6.2) that has been created on your desktop workspace.
After double-clicking on the icon (Fig. 6.1), the D-Link AirPlus
DWL-650+ Utility window will appear.
15
DWL-650+
Fig. 6.2
Configuration Utility
Link Info
After clicking on the Configuration Utility icon, the Link Info screen will display the
following:
Cardbus Adapter
Status: Displays the MAC Address of the Access Point that is associated with the
DWL-650+.
SSID: The Service Set Identifier is the name assigned to the wireless network. The
factory SSID setting is set to default.
TxRate: The factory setting is set to 11 Mbps; however, TxRate settings are
automatically determined by the DWL-650+ depending on the distance from the
access point.
Channel: Displays the channel information. By default, the channel is set to 6 and
selection is automatically determined by the DWL-650+.
Link Quality / Signal Strength: Displays the Link Quality for the DWL-650+
wireless connection to the access point. The Signal Strength represents the wireless
signal between the access point and the DWL-650+. The percentage coincides with
the graphical bar.
Data Rate: Displays the statistics of data transmitted and received.
Rescan: Rescans the network for the Access Point with the greatest signal strength
and connects the DWL-650+ automatically.
16
Configuration Utility
Configuration
To communicate on the network, all devices must have
the same settings for the following properties:
This Configuration
screen displays the
default settings for
the DWL-650+.
SSID - (Service Set Identifier) is a name that identifies a wireless network. Access
Points and wireless clients attempting to connect to a specific WLAN (Wireless Local
Area Network) must use the same SSID. The default setting is default.
Wireless Mode - Click on the pull-down menu; select from the following options:
Infrastructure - connecting the WLAN using an Access Point such as the
DWL-1000AP. (The default setting.)
Ad-Hoc – wireless mode used when connecting directly to a computer
equipped with a wireless adapter such as the D-Link AirPlus DWL-520
Wireless PCI adapter in a peer-to-peer environment.
Channel – The default channel setting is channel 6. However, the DWL-650+ will
automatically select the channel to match the channel setting for the selected
Access Point. In Ad Hoc mode, the channel must be manually set to the same
channel for each wireless adapter.
TX Rate - Select the transmission rate on the network. 11Mbps is the default setting.
Preamble - Select Long or Short Preamble. The Preamble defines the length of
the CRC block (Cyclic Redundancy Check is a common technique for detecting data
transmission errors) for communication between the Access Point and the roaming
wireless Network adapters. Long Preamble is the default setting. Note: High
network traffic areas should use the shorter preamble type.
Power Mode – Select from three modes:
Continuous Access Mode-this default setting consumes the most power
Maximum Power Save-this setting consumes the least power
Power Save- this setting consumes a moderate amount of power
4x Config – Select 4x Disable or 4x Enable. The 4x feature increases your data
throughput when 4x is enabled on both the wireless client and either the DWL900AP+ (wireless Access Point) or the DI-614+ (wireless Router.)
Click Apply to save the changes.
17
Configuration Utility
Encryption
D-Link AirPlus DWL-650+ 2.4GHz Wireless Cardbus Adapter
Fig. 6.5
Please note that all devices must share the same Encryption
settings to communicate on the network.
Data Encryption – enable Encryption by clicking on the box. The DWL650+ has Encryption disabled as the default setting.
Authentication mode – choose one of the following modes:
Open Authentication – communicates the key across the network
Shared Authentication – allows communication only with other
devices with identical WEP settings
Auto – will automatically adjust to the Authentication mode of the
wireless client
Network Key – enter a key in either ASCII (e.g., a word) or hexadecimal
format
Key Format - ASCII or Hexadecimal
Hexadecimal digits consist of the numbers 0-9 and the letters A-F
ASCII (American Standard Code for Information Interchange) is a code for
representing English letters as numbers from 0-127
Key type - select the key length, either 64, 128 or 256 bits
Key Index – You can create up to 4 different security keys
Click Apply to save the changes.
18
Configuration Utility
Site Survey
D-Link AirPlus DWL-650+ 2.4GHz Wireless Cardbus Adapter
Fig. 6.6
Available Networks
The top section of the window displays the Available Networks. Scroll up
and down the list and highlight the network to which you wish to connect.
Click on the Connect button.
Profiles
In the lower half of the screen, you can manage the profiles that you have
created for the wireless network at home, at the office and in public places.
Scroll up and down and highlight the profile that you wish to configure. You
can ADD or REMOVE a profile, or configure the Properties of the profile in
order to connect with an available network.
Properties
Click on Properties and the screen on the next page will appear.
19
Configuration Utility
Properties
Current Setting
Current Setting/Default Setting
default
Fig. 6.7
In this window you can configure all the properties of a profile in order to
connect with a network of your choice.
After you have entered your changes in this window, click OK to save the
changes.
20
Configuration Utility
About
D-Link AirPlus DWL-650+ 2.4GHz Wireless Cardbus Adapter
DWL-650+
D-Link AirPlus Configuration Utility
Fig. 6.8
The ABOUT screen gives you information about the Firmware and Utility
Versions of the DWL-650+.
21
7.
Troubleshooting
This chapter provides solutions to problems that can occur during the
installation and operation of the DWL-650+ Wireless Adapter. Read the
following descriptions if you are having problems. (The examples below are
illustrated in Windows XP. If you have another operating system, these solutions
will still apply although the appearance on your computer screen may differ.)
1. Checking the Installation of the Drivers for the Wireless Adapter
• Go to Start
• Right-click on
My Computer
• Click Properties
Fig. 7.1
• Select the Hardware Tab
• Click Device Manager
Fig. 7.2
22
Troubleshooting
• Double-click on Network
Adapters
• Right-click on D-Link
AirPlus DWL-650+
Wireless Adapter
• Select Properties to check
that the drivers are
installed properly.
D-Link AirPlus DWL-650+ Wireless Cardbus Adapter
Fig. 7.3
• Look under Device
Status
to check that the
device is working
properly.
D-Link AirPlus DWL-650+ Wireless Cardbus Adapter
D-Link AirPlus DWL-650+ Wireless Adapter
• Click OK
Fig. 7.4
23
Troubleshooting
2. I cannot connect to the access point or the wireless router.
• Make sure that the SSID on the DWL-650+ Cardbus adapter is
exactly the same as the SSID on the Access Point or wireless router.
• Move the DWL-650+ and Access Point or Wireless router into the
same room and then test the wireless connection.
• Disable all security settings. (WEP, MAC Address Control, AES)
• Make sure that the AP or wireless router is not locked down to a
different frequency
• Turn off your Access Point and the computer with the DWL-650+.
Turn on the Access Point, and then turn on the computer with the
DWL-650+.
• Refresh the DWL-650+ AirPlus Utility
3. The DWL-650+ Power and Link lights are not on.
• Check to see if the DWL-650+ Cardbus adapter is firmly inserted into
the Cardbus slot of your laptop computer.
4. I forgot my Encryption key.
•
Reset the Access Point to its factory default settings and restore the
DWL-650+ Wireless Cardbus Adapter to the factory default settings.
(The default settings are listed in the Using the Configuration
Utility section in this manual.)
5. The computer does not recognize the DWL-650+ Wireless Adapter.
•
Make sure that the DWL-650+ Wireless Adapter is properly seated in
the computer’s Cardbus slot.
•
If Windows does not detect the hardware upon insertion of the
adapter, make sure to completely remove drivers that were
previously loaded. To remove the drivers, do the following:
A. Under Tools> select Folder Options…> select View >
under Hidden files and folders > select Show hidden
files and folders
B. Uncheck Hide extension for known file types > click on
Apply
24
C. Search for the files TIACXLN.INF and TIACXLN.SYS.
Remove these files from the INF and SYSTEM32
(DRIVERS) folders in the Windows directory.
Note:
Windows XP and Windows 2000 will rename .inf files that
have not received WHQL certification into oem.inf files (e.g.,
oem1.inf.)
6. The computer with the DWL-650+ installed is unable to connect to
the wireless network and/or the Internet.
•
Check that the LED indicators for the broadband modem are
indicating normal activity. If not, there may be a problem with the
broadband connection.
•
Check that the LED indicators on the wireless router are functioning
properly. If not, check that the AC power and Ethernet cables are
firmly connected.
•
Check that the IP Address, subnet mask, gateway, and DNS settings
are correctly entered for the network
•
In Infrastructure mode, make sure the same Service Set Identifier
(SSID) is specified on the settings for the wireless clients and access
points. The SSID factory default setting for the D-Link AirPlus
products is default. (Double-click on the WLAN icon in the taskbar.
The Link Info screen will display the SSID setting.)
•
In Ad-Hoc mode, both wireless clients will need to have the same
SSID. Please note that it might be necessary to set up one client to
establish a BSS (Basic Service Set) and wait briefly before setting
up other clients. This prevents several clients from trying to establish
a BSS at the same time, which can result in multiple singular BSSs
being established, rather than a single BSS with multiple clients
associated to it.
•
Check that the Network Connection for the wireless client is
configured properly. Select AP (Infrastructure) when connecting to
an access point and select Ad-Hoc mode when connecting without
an access point. Double-click on the WLAN icon in the taskbar >
click on Configuration to change the settings for the wireless
adapter.
•
If Security is enabled, make sure that the correct encryption keys are
entered on both the DWL-650+ and the access point. Double-click
on the WLAN icon in the taskbar > click Encryption. Check to see
25
that the key selected is set to the same key as other devices on the
network.
7. How can I troubleshoot distance issues using the DWL-650+.
•
Move the DWL-650+ and Access Point or Wireless router into the
same room and then test the wireless connection.
•
Change the channel of the Access Point.
•
Move devices within the line of sight
8. How do I use the 4x feature?
8.
•
In the Configuration Utility, Click Configuration. Check the 4x
Enable box.
•
To use the 4x feature, you must use a 4x-enabled DWL-900AP+
Wireless Access Point or a 4x-enabled DI-614+ Wireless Broadband
Router in conjunction with the 4x-enabled DWL-520+.
Networking Basics
Using the Network Setup Wizard in Windows XP
In this section you will learn how to establish a network at home or work,
using Microsoft Windows XP.
Note: Please refer to websites such as http://www.homenethelp.com
and http://www.microsoft.com/windows2000 for information about
networking computers using Windows 2000, ME or 98.
Go to Start > Control Panel > Network Connections
Select Set up a home or small office network
When this screen appears, click Next.
26
Networking Basics
Using the Network Setup Wizard in Windows XP
Please follow all the instructions in this window:
Fig. 8.2
Click Next
In the following window, select the best description of your computer. If your
computer connects to the Internet through a gateway/router, select the
second option as shown.
Fig. 8.3
Click Next
27
Networking Basics
Enter a Computer description and a Computer name.
Fig. 8.4
Click Next
Enter a Workgroup name. All computers on your network should have the
same Workgroup name.
Fig. 8.5
Click Next
28
Networking Basics
Please wait while the wizard applies the changes.
Fig. 8.6
When the changes are complete, click Next.
Please wait while the wizard configures the computer.
This may take a few minutes.
Fig. 8.7
29
Networking Basics
In the window below, select the best option. In this example, Create a
Network Setup Disk has been selected. You will run this disk on each of
the computers on your network. Click Next.
Fig. 8.8
Insert a disk into the Floppy Disk Drive, in this case drive A:
Fig. 8.9
Format the disk if you wish, and click Next.
30
Networking Basics
Please wait while the wizard copies the files.
Fig. 8.10
Please read the information under Here’s how in the screen below. After
you complete the Network Setup Wizard you will use the Network Setup
Disk to run the Network Setup Wizard once on each of the computers on
your network. To continue, click Next
Fig. 8.11
31
Networking Basics
Please read the information on this screen, then click Finish to complete the
Network Setup Wizard.
Fig. 8.12
The new settings will take effect when you restart the computer. Click Yes
to restart the computer.
Fig. 8.13
You have completed configuring this computer. Next, you will need to run
the Network Setup Disk on all the other computers on your network. After
running the Network Setup Disk on all your computers, your new wireless
network will be ready to use.
32
Networking Basics
Naming your Computer
To name your computer, please follow these directions:
In Windows XP:
• Click Start (in the
lower left corner of
the screen)
• Right-click on My
Computer
•
Select Properties
and click
Fig. 8.14
•
Select the
Computer Name
Tab in the System
Properties window.
You may enter a
Computer description if
you wish; this field is
optional.
To rename the computer
or join a domain,
• Click Change
Fig. 8.15
33
Networking Basics
Naming your Computer
•
In this window, enter
the Computer
name.
•
Select Workgroup
and enter the name
of the Workgroup.
•
All computers on
your network must
have the same
Workgroup name.
•
Click OK
Fig. 8.16
Checking the IP Address in Windows XP/2000
Go to Start > All Programs > Accessories > Command Prompt
Fig. 8.17
34
Networking Basics
Checking the IP Address in Windows XP/2000
Type Command
Fig. 8.18
Type ipconfig /all at the prompt. All the configuration settings are displayed
as shown below.
D-Link AirPlus DWL-650+ Wireless Cardbus
Fig. 8.19
Type ipconfig /renew at the prompt to get a new IP Address, shown below.
Fig. 8.20
(Windows 98/ME users: go to Start > Run. Type Command. Type
winipcfg at the prompt. Click Release and Renew to obtain a new IP
Address.)
35
Networking Basics
Assigning a Static IP Address in Windows XP/2000
Note: Residential Gateways/Broadband Routers will automatically assign IP
Addresses to the computers on the network, using DHCP (Dynamic Host
Configuration Protocol) technology. If you are using a DHCP-capable
Gateway/Router you will not need to assign Static IP Addresses.
If you are not using a DHCP capable Gateway/Router, or you need to assign
a Static IP Address, please follow these instructions:
(The following illustrations are shown using Windows XP, other Operating Systems will be similar.)
•
Go to Start
•
Double-click on
Control Panel
Fig. 8.21
•
Double-click on
Network Connections
Fig. 8.22
36
Networking Basics
Assigning a Static IP Address (continued)
•
Right-click on Local
Area Connections.
•
Click Properties
Fig. 8.23
•
Highlight Internet
Protocol (TCP/IP)
D-Link AirPlus DWL-650+ Wireless Adapter
•
Click Properties
Fig. 8.24
37
Networking Basics
Assigning a Static IP Address (continued)
•
Select Use the following IP address
in the Internet Protocol (TCP/IP) Properties window.
• Input your IP address and subnet mask. (The IP Addresses on your
network must be within the same range. For example, if one computer
has an IP Address of 192.168.0.2, the other computers should have IP
Addresses that are between 192.168.0.3 and 192.168.0.254. No two
computers can have the same IP Address. The subnet mask must be the
same for all the computers on the network.)
IP Address:
e.g.,192.168.0.2
Subnet Mask:
255.255.255.0
Default Gateway: Enter
the LAN IP address of
the Wireless Router.
(D-Link wireless routers
have a LAN IP address
of 192.168.0.1)
•
•
Select Use the
following DNS server
address. Enter the
LAN IP address of the
Wireless Router. (D-Link
wireless routers have a
LAN IP address of
192.168.0.1)
192 168
0
1
192 168
0
1
Fig. 8.25
Click OK
You have completed the assignment of a Static IP Address. (You do not need to
assign a Static IP Address if you have a DHCP-capable Gateway/Router.)
38
Checking the Wireless Connection by Pinging
For Windows XP and 2000:
Go to Start > Run > type
cmd. A window similar to
Fig. 8.35 will appear. Type
ping xxx.xxx.xxx.xxx,
where xxx is the IP address
of the Wireless Router or
Access Point.
A good wireless connection
will show four replies from
the wireless router or access
point, as shown.
Fig. 8.26
For Windows Me and 98:
Go to Start > Run > type
command. A window
similar to Fig. 8.36 will
appear. Type ping
xxx.xxx.xxx.xxx, where
xxx is the IP address of the
Wireless Router or Access
Point. A good wireless
connection will show four
replies from the wireless
router or access point, as
Fig. 8.27
shown.
39
Adding and Sharing Printers in Windows XP
After you have run the Network Setup Wizard on all the computers in your
network (please see the Network Setup Wizard section at the beginning of
Networking Basics,) you can use the Add Printer Wizard to add or share a
printer on your network.
Whether you want to add a local printer (a printer connected directly to one
computer,) share an LPR printer (a printer connected to a print server) or
share a network printer (a printer connected to your network through a
Gateway/Router,) use the Add Printer Wizard. Please follow the directions
below:
First, make sure that you have run the Network Setup Wizard on all of
the computers on your network.
We will show you 3 ways to use the Add Printer Wizard
1. Adding a local printer
2. Sharing an network printer
3. Sharing an LPR printer
40
Networking Basics
Adding a local printer
(A printer connected directly to a computer)
A printer that is not shared on the network and is connected directly to one
computer is called a local printer. If you do not need to share your printer
on a network, follow these directions to add the printer to one computer.
•
Go to Start>
Printers and
Faxes
Fig. 8.28
• Click on Add a printer
Fig. 8.29
41
Networking Basics
Adding a local printer
• Click Next
Fig. 8.30
• Select Local printer
attached to this computer
• (Deselect Automatically detect
and install my Plug and Play
printer if it has been selected.)
• Click Next
Fig. 8.31
•
Select Use the following
port:
•
From the pull-down menu
select the correct port for
your printer
(Most computers use the
LPT1: port, as shown in the
illustration.)
•
Click Next
Fig. 8.32
42
Networking Basics
Adding a local printer
• Select and highlight the
correct driver for your
printer.
• Click Next
(If the correct driver is not
displayed, insert the CD or
floppy disk that came with your
printer and click Have Disk.)
Fig. 8.33
• At this screen, you can
change the name of the
printer (optional.)
• Click Next
Fig. 8.34
• Select Yes, to print a
test page. A
successful printing will
confirm that you have
chosen the correct
driver.
• Click Next
Fig. 8.35
43
Networking Basics
Adding a local printer
This screen gives you information about your printer.
Fig. 8.36
Click Finish
When the test page has printed,
Fig. 8.37
Click OK
44
Networking Basics
Adding a local printer
•
Go to Start> Printers and
Faxes
A successful installation will
display the printer icon as
shown at right.
You have successfully added a
local printer.
Fig. 8.38
Setting up a Network Printer
After you have run the Network Setup Wizard on all the computers on your
network, you can run the Add Printer Wizard on all the computers on your
network. Please follow these directions to use the Add Printer Wizard to
share the printer on your network:
•
Go to Start>
Printers and Faxes
Fig. 8.39
45
Networking Basics
Setting up a network printer
•
Click on
Add a Printer
Fig. 8.40
•
Click Next
Fig. 8.41
•
Select Network
Printer
•
Click Next
Fig. 8.42
46
Networking Basics
Setting up a network printer
•
Select Browse for a printer
•
Click Next
Fig. 8.43
•
Select the printer you
would like to share.
•
Click Next
Fig. 8.44
•
Click Finish
Fig. 8.45
47
Networking Basics
Setting up a network printer
To check for proper installation:
• Go to Start>
Printers and Faxes
Fig. 8.46
The printer icon will appear
at right, indicating proper
installation.
You have completed adding
the printer.
To share this printer on
your network:
• Remember the
printer name
• Run the Add Printer
Wizard on all the
computers on your
network.
• Make sure you have
already run the
Network Setup
Wizard on all the
network computers.
After you run the Add
Printer Wizard on all the
computers in the
network, you can share
the printer.
Fig. 8.47
48
Networking Basics
Setting up an LPR printer
To share an LPR printer (using a print server,) you will need a Print Server
such as the DP-101P+. Please make sure that you have run the Network
Setup Wizard on all the computers on your network. To share an LPR
printer, please follow these directions:
• Go to Start>
Printers
and Faxes
• Click on
Add a Printer
The screen to the
right will display.
• Click Next
Fig. 8.48
• Select
Local
Printer
• Click Next
Fig. 8.49
49
Networking Basics
Setting up an LPR printer
• Select Create a new port
• From the pull-down menu,
select Standard TCP/IP
Port, as shown.
• Click Next
Fig. 8.50
•
Please read the instructions
on this screen.
•
Click Next
Fig. 8.51
•
Enter the Printer IP
Address and the Port
Name, as shown.
•
Click Next
Fig. 8.52
50
Networking Basics
Setting up an LPR printer
•
In this screen,
select Custom.
•
Click Settings
Fig. 8.53
•
Enter the Port
Name and the
Printer Name or
IP Address.
•
Select LPR
•
Enter a Queue
Name. If there
is more than
one port on the
print server, you
must name the
Queue.
•
Click OK
Fig. 8.54
51
Networking Basics
Setting up an LPR printer
• This screen will show
you information
about your printer.
• Click Finish
Fig. 8.55
• Select the printer you
are adding from the
list of Printers.
• Insert the printer
driver disk that came
with your printer.
• Click Have Disk
Fig. 8.56
If the printer driver is already
installed,
• Select Keep existing
driver
• Click Next
Fig. 8.57
52
Networking Basics
Setting up an LPR printer
• You can rename your
printer if you choose. It
is optional.
Please remember the name of
your printer. You will need this
information when you use the
Add Printer Wizard on the
other computers on your
network.
• Click Next
Fig. 8.58
• Select Yes, to print a
test page.
• Click Next
Fig. 8.59
This screen will display
information about your
printer.
• Click Finish to
complete the
addition of the
printer.
• Please run the Add
Printer Wizard on
all the computers
on your network in
order to share the
printer.
Fig. 8.60
Note: You must run the Network Setup Wizard
on all the computers on your network before you
run the Add Printer Wizard.
53
Networking Basics
Other Tasks
For help with other tasks in home or small office networking, see Using the
Shared Documents folder and Sharing files and folders in the Help and
Support Center in Microsoft Windows XP.
9.
Technical Specifications
Standards:
• IEEE 802.11b
• Wi-Fi Certified
Adapter Type:
• PC Cardbus slot
System Requirements:
• Laptop with Cardbus Controller
Supported Operating Systems:
• Windows XP
• Windows 2000
• Windows ME
• Windows 98
Data Security:
• 64/128/256-bit WEP (Wired Equivalent Privacy) Encryption
• Supports 802.1x authentication
Data Rate: Mbps/channel
• 22 : PBCC
• 11 : CCK/PBCC
• 5.5 : CCK/PBCC
• 2 : QPSK
• 1 : BPSK
Key Management:
• Automatic Dynamic Key Allocation (ADKA) through public key
Range:
• Indoors – up to 328 feet (100 meters)
54
•
Outdoors – up to 1,312 feet (400 meters)
Diagnostic LED:
• Power – solid green light indicates power connection
• Link/Activity – green solid/blinking light indicates Link/Activity
Power Specifications:
• Operating Voltage: 3.3V
Network Architecture:
• Supports Ad-Hoc Mode (Peer-to-Peer without Access Point) or
Infrastructure Mode (Communications to wired networks via Access
Points with Roaming)
• Compliant with IEEE 802.11b Standards
Antenna:
• Internal patch antenna supporting diversity
• Mobility: Seamless roaming across cell boundaries within access
point range
Frequency Range:
• 2.4 – 2.4835 GHz, Direct Sequence Spread Spectrum (DSSS)
Operating Channels:
• 1-11 United States (FCC)
• 1-11 Canada (DOC)
• 1-14 Japan (MKK)
• 1-13 Europe (Except Spain and France) (ETSI)
Physical Dimensions:
• L = 4.50 inches (114 mm)
• W = 2.25 inches (54 mm)
• H = .25 inches (6 mm)
Temperature:
• Operating Temperature: 14ºF to 131ºF (-10°C to 55°C)
• Storage Temperature: -4ºF to 167ºF (-20°C to 75°C)
Humidity:
• Maximum up to 95% Non-condensing
Emissions:
• FCC
55
•
CE
Safety:
UL
10. Contacting Technical Support
You can find software updates and user documentation on the D-Link
website.
D-Link provides free technical support for customers within the United States
and within Canada for the duration of the warranty period on this product.
U.S. and Canadian customers can contact D-Link technical support through
our website, or by phone.
Tech Support for customers within the United States:
D-Link Technical Support over the Telephone:
(877) 453-5465
24 hours a day, seven days a week.
D-Link Technical Support over the Internet:
http://support.dlink.com
email:[email protected]
Tech Support for customers within Canada:
D-Link Technical Support over the Telephone:
(800) 361-5265
Monday to Friday 8:30am to 9:00pm EST
D-Link Technical Support over the Internet:
http://support.dlink.ca
email:[email protected]
56
11. Limited Warranty and Registration
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited
warranty for its product only to the person or entity that originally purchased the product from:
•
•
D-Link or its authorized reseller or distributor and
Products purchased and delivered within the fifty states of the United States, the District of
Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, addresses with an
APO or FPO.
Limited Warranty: D-Link warrants that the hardware portion of the D-Link products described below will
be free from material defects in workmanship and materials from the date of original retail purchase of the
product, for the period set forth below applicable to the product type (“Warranty Period”), except as
otherwise stated herein.
3-Year Limited Warranty for the Product(s) is defined as follows:
•
•
•
Hardware (excluding power supplies and fans) Three (3) Years
Power Supplies and Fans One (1) Year
Spare parts and spare kits Ninety (90) days
D-Link’s sole obligation shall be to repair or replace the defective Hardware during the Warranty Period at
no charge to the original owner or to refund at D-Link’s sole discretion. Such repair or replacement will be
rendered by D-Link at an Authorized D-Link Service Office. The replacement Hardware need not be new
or have an identical make, model or part. D-Link may in its sole discretion replace the defective
Hardware (or any part thereof) with any reconditioned product that D-Link reasonably determines is
substantially equivalent (or superior) in all material respects to the defective Hardware. Repaired or
replacement Hardware will be warranted for the remainder of the original Warranty Period from the date
of original retail purchase. If a material defect is incapable of correction, or if D-Link determines in its sole
discretion that it is not practical to repair or replace the defective Hardware, the price paid by the original
purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective
Hardware. All Hardware (or part thereof) that is replaced by D-Link, or for which the purchase price is
refunded, shall become the property of D-Link upon replacement or refund.
Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will
substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the
applicable documentation, from the date of original retail purchase of the Software for a period of ninety
(90) days (“Warranty Period”), provided that the Software is properly installed on approved hardware and
operated as contemplated in its documentation. D-Link further warrants that, during the Warranty Period,
the magnetic media on which D-Link delivers the Software will be free of physical defects. D-Link’s sole
obligation shall be to replace the non-conforming Software (or defective media) with software that
substantially conforms to D-Link’s functional specifications for the Software or to refund at D-Link’s sole
discretion. Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to
the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the
Software. Software will be warranted for the remainder of the original Warranty Period from the date or
original retail purchase. If a material non-conformance is incapable of correction, or if D-Link determines
in its sole discretion that it is not practical to replace the non-conforming Software, the price paid by the
original licensee for the non-conforming Software will be refunded by D-Link; provided that the nonconforming Software (and all copies thereof) is first returned to D-Link. The license granted respecting
any Software for which a refund is given automatically terminates.
Non-Applicability of Warranty: The Limited Warranty provided hereunder for hardware and software of
D-Link's products will not be applied to and does not cover any refurbished product and any product
purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers,
or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case,
the product is being sold "As-Is" without any warranty whatsoever including, without limitation, the Limited
Warranty as described herein, notwithstanding anything stated herein to the contrary.
Submitting A Claim: The customer shall return the product to the original purchase point based on its
return policy. In case the return policy period has expired and the product is within warranty, the
customer shall submit a claim to D-Link as outlined below:
•
The customer must submit with the product as part of the claim a written description of the
Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm the same.
57
•
The original product owner must obtain a Return Material Authorization (“RMA”) number from
the Authorized D-Link Service Office and, if requested, provide written proof of purchase of the
product (such as a copy of the dated purchase invoice for the product) before the warranty service is
provided.
•
After an RMA number is issued, the defective product must be packaged securely in the
original or other suitable shipping package to ensure that it will not be damaged in transit, and the
RMA number must be prominently marked on the outside of the package. Do not include any
manuals or accessories in the shipping package. D-Link will only replace the defective portion of the
Product and will not ship back any accessories.
•
The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery
(“COD”) is allowed. Products sent COD will either be rejected by D-Link or become the property of
D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 53
Discovery Drive, Irvine, CA 92618. D-Link will not be held responsible for any packages that are
lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS
Ground or any common carrier selected by D-Link, with shipping charges prepaid. Expedited
shipping is available if shipping charges are prepaid by the customer and upon request.
D-Link may reject or return any product that is not packaged and shipped in strict compliance with the
foregoing requirements, or for which an RMA number is not visible from the outside of the package. The
product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product
that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by
D-Link not to be defective or non-conforming.
What Is Not Covered: This limited warranty provided by D-Link does not cover: Products, if in D-Link’s
judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence,
misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in
the documentation for the product, or if the model or serial number has been altered, tampered with,
defaced or removed; Initial installation, installation and removal of the product for repair, and shipping
costs; Operational adjustments covered in the operating manual for the product, and normal maintenance;
Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage;
Any hardware, software, firmware or other products or services provided by anyone other than D-Link;
Products that have been purchased from inventory clearance or liquidation sales or other sales in which
D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product.
Repair by anyone other than D-Link or an Authorized D-Link Service Office will void this Warranty.
Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE
PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER
INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE
DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH
IMPLIED WARRANTY SHALL BE LIMITED TO NINETY (90) DAYS. EXCEPT AS EXPRESSLY
COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE
QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF
THE PRODUCT.
Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE
UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE
THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY
CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT
NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK
STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR
COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT IS CONNECTED WITH, LOSS OF
INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT
RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE
PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS
LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS
REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT.
THE MAXIMUM LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE
PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING EXPRESS WRITTEN
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES
OR REMEDIES, EXPRESS, IMPLIED OR STATUTORY
Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some
states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This limited
warranty provides specific legal rights and the product owner may also have other rights which vary from
state to state.
58
Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered
trademarks are the property of their respective manufacturers or owners.
Copyright Statement: No part of this publication or documentation accompanying this Product may be
reproduced in any form or by any means or used to make any derivative such as translation,
transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as
stipulated by the United States Copyright Act of 1976. Contents are subject to change without prior
©
notice. Copyright 2002 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communication. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment; such modifications could void the user’s authority to operate the
equipment.
(1) The devices are restricted to indoor operations within the 5.15 to 5.25GHz range. (2) For this
device to operate in the 5.15 to 5.25GHz range, the devices must use integral antennas.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
The antenna(s) used for this equipment must be installed to provide a separation distance of at least
eight inches (20 cm) from all persons.
This equipment must not be operated in conjunction with any other antenna.
Register online your D-Link product at http://support.dlink.com/register/
031003
59
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement