Tech Lighting Cleo Grande 920TDCLGCNCF Canopy Installation Instructions

Tech Lighting Cleo Grande 920TDCLGCNCF Canopy Installation Instructions

Below you will find brief information for Canopy Cleo Grande 920TDCLGCNCF. The Cleo Grande 920TDCLGCNCF is a stylish and functional canopy that is perfect for adding a touch of elegance to any room. It is easy to install and features a sleek design that complements any decor. The Cleo Grande 920TDCLGCNCF also provides durable and long-lasting performance, making it a great choice for both residential and commercial applications.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Canopy Cleo Grande 920TDCLGCNCF Installation Instructions | Manualzz

Installation Instructions for

Cleo Grande Canopy (Compact Fluorescent)

920TDCLGCNCF

295TDCLGC_

1.0

PENDANTS

GENERAL PRODUCT INFORMATION:

This product is suitable for damp locations.

This product can mount to either a 4" square electrical box with round plaster ring or an octagon electrical box.

C AUTION — RISK OF FIRE

This product requires installation by a qualified electrician. Before installing be sure to read all instructions and TURN OFF POWER TO THE

ELECTRICAL BOX.

NOTE : Due to the weight and complexity of this fixture, assistance will be need for installation.

Preparing the Canopy

1A

CANOPY

SCREW

1

CANOPY

2

CAP

BACK PLATE

1B

1

3 3

#8-32

SCREW

1

2

Unscrew and remove all three screws and seperate the backplate from the canopy.

Unscrew and remove the cap.

1

3 Mount the backplate to the electrical box with the two provided #8-32 screws.

Install the Fixture

2A

3

2C

3

7

6

1

CABLE

CLUTCH

AIRCRAFT

CABLE

CORD

1 Feed the aircraft cables through the cable clutch in the canopy.

2 Evenly pull the aircraft cable up through the canopy to raise the fixture to the desired length.

3 Cut off the excess aircraft cable leaving enough for fine leveling later.

2B

POWER CORD

SET

SCREW

4

NOTE: The power cord does not support the fixture.

For a casual “lazy cord” look, cut the power cord several inches longer that the drop height of the fixture.

6 Once the desired look is determined, tighten the set screw on the strain relief.

7 Leave 6” of the cord behind the canopy for power connections and cut the excess cord.

5

Note : Taping down the frayed end of the cloth cover may assist in feeding the power cord through the strain relief.

4 If necessary loosen the set screw in the strain relief and feed the power cord from the fixture through the cap and into the canopy.

5 Re-screw the cap back on.

2

Install the Canopy

3A

4

4

3

6

5

3B

CANOPY

SCREW

2

BALLAST

1 Strip the cable behind the canopy and also strip the ends of the inner wires.

2 Connect the red ballast wire to one of the insulated pendant wires.

3 Connect the yellow ballast wire to the other insulated pendant wire.

4 Connect the fixture and the crossbar ground wire to a suitable ground in accordance with local electrical codes.

5 Connect the white ballast/driver wire to the neutral power line wire.

6 Connect the black ballast/driver wire to the hot power line wire.

7 Place all wires, wire nut connections, and the ballast properly into the electrical box.

8 Remount the canopy to the backplate by securing

3C

CABLE

CLUTCH

9 Adjust the aircraft cables until the fixture is level; feed the cable into the cable clutch to raise the fixture and push in on the cable clutch nipple to release the cable and lower the fixture.

3

SAVE THESE INSTRUCTIONS!

4

7400 Linder Ave, Skokie, IL 60077

847.410.4400

www.techlighting.com

© 2012 Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is a registered trademark of Tech Lighting, L.L.C. Tech Lighting reserves the right to change specifications for product improvements without notification.

A Generation Brands Company

advertisement

Key Features

  • Suitable for damp locations
  • Mounts to 4" square electrical box
  • Mounts to octagon electrical box
  • Requires installation by a qualified electrician
  • Provides detailed installation instructions
  • Easy to install and maintain
  • Durable and long-lasting

Frequently Answers and Questions

Can this product be used in damp locations?
Yes, this product is suitable for damp locations.
What type of electrical box can this product be mounted to?
This product can mount to either a 4" square electrical box with round plaster ring or an octagon electrical box.
Who should install this product?
This product requires installation by a qualified electrician.

Related manuals

Download PDF

advertisement