Performance Track Pack

INSTRUCTIONS

Keep these instructions for future reference as they contain important information.

CRASH CANYON™ SET

CONTENTS:

CANYON FACE

(2) 2" CANYON HAND BANDS

CANYON BASE

STARTER RAMP

3" LAUNCHER BAND

STARTER GATE

2 CANYON HANDS

4-SPEED LAUNCHER

CONNECTOR

(3) 21" TRACK PIECES

C-CLAMP

2 CANYON SHOULDERS

K4347-0920

(2) 3" CANYON SHOULDER BANDS 5+

© 2007 Mattel, Inc. All Rights Reserved.

Mattel, Inc., 333 Continental Blvd., El Segundo, CA 90245 U.S.A. Consumer Relations 1 (800) 524-8697 service.mattel.com. • Mattel Canada Inc.,

Mississauga, Ontario L5R 3W2. You may call us free at 1-800-524-8697. • Mattel U.K. Ltd., Vanwall Business Park, Maidenhead SL6 4UB. Helpline

01628500303 • Mattel Australia Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service - 1300 135 312. • Mattel East Asia Ltd., Room 1106,

South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. • Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.(993532-P) Lot 13.5, 13th

Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ. Tel:03-78803817, Fax:03-78803867.

®

APPLY LABELS:

Apply labels prior to assembly.

1

11

2

5

3

4

5

6

7

8

9

10

11

1

STARTER GATE

BUTTON

C-CLAMP

LAY OUT THE TRACK

Handy tip: To protect sensitive furniture surfaces, use a cloth or towel between the

C-Clamp and the surface to be clamped.

To regulate speed of car, change the height of the track. Higher clamp positions should produce higher speeds.

7

6

1

10

3 4

2

STARTER GATE

TO PLAY

1.

Press down on the starter gate button, insert a car. Gate will automatically lower to allow car to roll down.

2.

At other end of track, pull launch slide back on launcher until it catches.

There are 4 positions. The farther back you set it, the faster the car goes. Load a second car into the launcher. Push down on the launcher button to launch. Time your launch so the 2 cars collide inside the canyon face.

REPLACE RUBBER

BAND IN LAUNCHERS:

Use one 3" rubber band.

Open bottom cover. Fold rubber band in half. Place center under hook. Slip ends around launcher hooks. Close bottom cover.

RUBBER BAND

CONNECTOR

Crash inside the canyon and see it EXPLODE!

8

9

ASSEMBLE BASE

HOOK

HEAD/SHOULDER

ASSEMBLY

Assemble face to shoulders

(one time assembly).

Stretch 3" rubber band over tabs as shown on both shoulders.

Load canyon assembly onto base.

TABS

SHOULDER

Reset stem should be over notch as shown.

RUBBER BAND

NOTE: Head/shoulder assembly must be put on before the hands.

FACE

RESET STEM

SHOULDER

BOTTOM

COVER

HAND ASSEMBLY

Stretch 2" rubber band over tabs. Assemble as shown.

RUBBER BAND

LAUNCHER

HOOKS

TAB

Catch rubber band on notch of tab.

TAB

NOTCH

Time your launch so both cars collide inside the canyon face!

To lock canyon hands, push down and under notch on stem.

2

LAUNCHER

BUTTON

WRECK 'N' ROLL™ STUNT SET

CONTENTS

5

1 2 3 4

6

17 18

19

15

20

7

11

9

10

12

8

16

22

21

23

24

BARREL

2 CRANES

2 LOOP BASES

LAY OUT THE TRACK

Handy tip: To protect sensitive furniture surfaces, use a cloth or towel between the C-Clamp and the surface to be clamped.

TO MAKE LOOPS, fit (2)

12" track sections with loop connector onto each loop base as shown.

5

6

12" TRACK PIECE

Connect the 2 loops with the 4" track.

1 2 3 4

CONNECTOR

C-CLAMP

4" TRACK PIECE

CRANE ARM

(4) 12" TRACK PIECES

(for loops)

(4) 20" TRACK PIECES

2 LOOP CONNECTORS

12" TRACK PIECE

12" TRACK PIECE

17 18

19

15

20

7

11

9 10

12

8

16

22

21

23 24

Apply labels prior to assembly.

OTHER

SIDE

12 11

OTHER

SIDE

20

22

OTHER

SIDE

23 18

1 2

APPLY LABELS

7

OTHER

SIDE

8

5

OTHER

SIDE 6

OTHER

SIDE

14

OTHER

SIDE

16

15

13

OTHER

SIDE

19

OTHER

SIDE

3

17

4

24

21

9

10 OTHER

SIDE

C-CLAMP

PLACE TAPE

OR

BOOK HERE.

PLACE

TAPE OR

BOOK HERE.

ATTACH

CRANES

On smooth surfaces tape down base. On carpeted surfaces use books to hold base.

4" TRACK PIECE

Swing the crane arm.

Can your vehicle make it through the loops?

20" TRACK PIECE

To regulate speed of car, change the height of the track. Higher clamp positions should produce higher speeds.

An additional Hot Wheels® car or barrel, can be placed in the crane claw.

Small coins may be placed in barrel for added weight.

20" TRACK PIECE

CONNECTOR

20" TRACK PIECE

TRACK SECTION

ADJUSTABLE

JUMP RAMP

IN

OUT

LOOPS

20" TRACK PIECE

Capture the flag or push the barrel along the track.

JUNKYARD DOG

®

ATTACK TRACK

®

SET

CONTENTS

LAUNCHER

SHORT TRACK

LONG TRACK

ASSEMBLY

1 2 3

FINAL ASSEMBLY

11

10

9

TO PLAY

Launch 1 or 2 cars!

2 CARS

4 5 6 7

1 CAR

Connect long track.

8

CRASHIN' TRANSPORT

®

SET

CONTENTS

LAUNCHER

BASE

ASSEMBLY

1

B

2

Pull track and launcher out slightly to unlock from base.

A

3

GET READY TO PLAY

1. Push launch slide back until it catches. It has four positions. The farther back you set it, the more powerful the launch.

2. Load Hot Wheels® car as shown.

3. Push down on button to launch.

2 1

LAUNCHER

REPLACE RUBBER

BAND IN LAUNCHER:

Open bottom cover. Fold rubber band in half. Place center under hook. Slip ends around launcher hooks.

Close bottom cover.

Rubber band

Hook

TO PLAY

Option 1 (Flat Track)

Launch car under truck.

B

OTHER SIDE

Turn lever to lift track and convert to a jump ramp.

Bottom cover

Hook

Option 2 (Jump Track)

Adjust track height and launcher setting for optimum effect.

A

FINAL ASSEMBLY

Toy:

INSTRUCTION SHEET

SPECIFICATIONS

Performance Track Pack

Toy No.:

Part No.:

Trim Size:

Folded Size:

Type of Fold:

# colors:

Colors:

Paper Stock:

K4347 0920

34"W x11" H

8.5" W x11" H

Single

One

Black

White Offset

70 lb.

Paper Weight:

EDM No.: