Pure Fitness 2 in 1 Elliptical Trainer

Model No. 8535DT

Owner’s Manual

Please read all the instructions before using this product.

Consult a physician before beginning any exercise program or strenuous activity

Do not allow more than one person on the trainer at any time.

ADULT ASSEMBLY REQUIRED.

To ensure warranty coverage, please visit www.pureglobalbrands.com to register your product

The contents of this package are not suitable for children under 3 years.

Contains small parts which may cause choking.

Pure Fitness is a Trademark of

Pure Global Brands, Inc.

OWNERS MANUAL

CUSTOMER SERVICE INFORMATION

Thank you for purchasing our Pure Fitness™ 2 in 1 Elliptical Trainer.

At Pure Global Brands, we want all of our customers to be completely satisfied with their purchase.

Please take time to review the contents of the product you just received to make sure that all of the parts are included. If you find that any parts are missing or damaged, we will happily provide replacement parts at no charge within 30 days of purchase. Please keep in mind that for select damaged part replacement requests, we will require a photo for submission to our quality control office.

To order these parts, or if you have any other questions or concerns about this Pure Global product, please e-mail the Pure Global Brands, Inc. customer service department at: [email protected] or contact us at 1-866-498-5269.

You can also visit our website at: www.pureglobalbrands.com

If you request replacement parts, please be sure to include the following information in your correspondence:

YOUR NAME

YOUR MAILING ADDRESS

YOUR EMAIL ADDRESS

RETAILER WHERE YOU PURCHASED PRODUCT

DATE OF PURCHASE

ORDER # (IF AVAILABLE)

PRODUCT MODEL #: 8535DT

SERIAL #

PRODUCT NAME: Pure Fitness 2 in 1 Elliptical Trainer

PART # (located in manual)

QUANTITY NEEDED

PICTURE OF DAMAGED PART(s) – SUBMIT VIA Email , Fax, or Mail

Again, thank you for purchasing a Pure Global Brands product.

Sincerely,

Customer Service

Pure Global Brands, Inc.

8040 Belvedere Road

West Palm Beach, FL 33411

1-866-498-5269

LIMITED WARRANTY

Pure Global Brands, Inc. warrants this product to be free from defects in workmanship and materials under normal use and conditions for the duration of the period outlined below FROM THE DATE OF

ORIGINAL PURCHASE. This Limited Warranty is not transferable and is available only for the original purchaser of the Product.

The various components of this equipment are warranted against defects and workmanship for the following time period(s):

•

•

Steel Frame 1-year.

All Other Parts 90-Days

All warranty coverage extends only to the original retail purchaser from the date of purchase.

Pure Fitness’s obligation under this Warranty is limited to replacing or repairing, at Pure Fitness’s option, the product at one of its authorized service centers. All products for which a warranty claim is made must be received by Pure Fitness at one of its authorized service centers and accompanied by sufficient proof of purchase (photocopy of the original store receipt, indicating the date of purchase). All freight and handling fees are the responsibility of the consumer to pay, both to and from

Pure Fitness. All warranty claims must be pre-authorized by Pure Fitness. Pre-authorization can be obtained by calling 866-498-5269. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage, or repairs not provided by a Pure Fitness authorized service center or for products used for commercial or rental purposes. This warranty does not cover ordinary wear and tear, weathering, failure to follow directions, improper installation, improper maintenance, or acts of Nature (such as damage caused by wind, lightning, snow, water, or ice). Weather damage, damage caused by unauthorized repair work or damage caused by improper use of the products are not covered by the product warranty. No other Warranty beyond that specifically set forth above is authorized by Pure Fitness.

PURE FITNESS IS NOT RESPONSIBLE OR LIABLE FOR INDIRECT, SPECIAL OR

CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE

USE OR PERFORMANCE OF THE PRODUCT OR OTHER DAMAGES WITH RESPECT

TO ANY ECONOMIC LOSS, LOSS OF PROPERTY, LOSS OF REVENUE OR PROFITS,

LOSS OF ENJOYMENT OR USE, COST OF REMOVAL, INSTALLATION OR OTHER

CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. ACCORDINGLY, THE

ABOVE LIMITATION MAY NOT APPLY TO YOU. THE WARRANTY EXTENDED HERE-

UNDER IS IN LIEU OF ALL OTHER WARRANTIES AND Pure Fitness SPECIFICALLY

DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE IS LIMITED IN ITS SCOPE AND DURATION TO THE TERMS

SET FORTH HEREIN. SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG

AN IMPLIED WARRANTY LASTS. ACCORDINGLY, THE ABOVE LIMITATION MAY

NOT APPLY TO YOU.

This warranty gives you specific legal rights. You may also have other rights, which vary from state to state.

WARNING

CHOKING HAZARD – Small parts

NOT for children under 3 years.

Warning

While every attempt is made to ensure the highest degree of protection in all equipment, we cannot guarantee freedom from injury. The user assumes all risks of injury due to use. All merchandise is sold on this condition, which no representative of the company can waive or change.

WARNING

IMPORTANT – PLEASE READ!

PRIOR TO ASSEMBLING:

Please visit: www.pureglobalbrands.com for any important product information updates and/or additional safety warnings before assembling or using this product.

Use search word: 8535DT

WARNINGS – GENERAL SAFETY ADVICE

Please read these instructions in their entirety before use and retain for future reference.

● Ensure that this product has been assembled correctly, per the instructions in the manual.

● This manual is designed to help you assemble, adjust, maintain and use the product. It contains important information regarding your safety and your use of this equipment.

● ALWAYS check this product before each use for missing or loose bolts and damaged parts.

Carefully inspect pedals, handle assemblies and the resistance belt on the fan wheel to check for damage or significant fraying and ensure the seat is secure in its housing.

● ALWAYS ensure that the wheel and pedal assemblies move freely and do not exhibit any obvious signs of distress by testing the moving parts on this unit before beginning an exercise.

● NEVER make or attempt to make any modifications or repairs to this product.

● ALWAYS hold the Handles when mounting and dismounting this product to prevent the pedals from accidentally moving when you are securing your feet in position or sitting down on the seat.

● NEVER attempt to suddenly stop pedaling or switch the direction of pedaling while moving, as serious injury and/or severe damage to the unit can occur, for which Pure Global is not liable.

● ALWAYS consult a physician before beginning any exercise program. Ask your doctor to evaluate your present fitness level and determine the exercise program that is most appropriate for your particular age and/or physical condition.

● IF YOU EXPERIENCE any pain or tightness in your chest, irregular heartbeats, shortness of breath, faintness, dizziness, or other unusual discomfort while exercising, STOP and immediately consult your physician and/or obtain medical assistance.

● This machine is intended for indoor individual home use only, it is not designed for commercial use or for use in communal workout areas.

● DO NOT allow children or pets to use, climb on, or play near this product.

● NEVER allow more than one person at a time on this product.

● Ensure that the product is on level ground. If necessary, use a rubber mat under the machine to reduce the possibility of slipping during use.

● Warm up at least 5-10 minutes before each workout and to cool down for at least 5-10 minutes afterwards.

● NEVER hold your breath while exercising.

● Rest adequately between workouts to allow your muscles to tone and develop.

● DO NOT wear loose fitting clothing, belt buckles, or jewelry, including but not limited to rings, chains, and pins before commencing exercise; this can be extremely dangerous.

● DO NOT stand or kneel on the seat.

● ALWAYS wear the appropriate fitness footwear. DO NOT use this product barefooted or with socks only. If applicable, ensure that any shoe laces will not become caught in moving parts.

● NEVER exceed the MAXIMUM WEIGHT LIMIT of 220LBS (100KGS)

● Dispose of all packaging materials safely and per local ordinance.

● Please retain this information for future reference.

8535DT EXPLODED VIEW

8535DT PARTS LIST

NOTE: For your convenience, your 2 in 1 Elliptical Trainer has been pre-assembled. Many of the items on this list are for troubleshooting and parts identification

ONLY, and will not be needed for assembly.

No.

Description

7

8

5

6

3

4

1

2

Main Frame

Left Handrail Arm Ø25x1.8

Right Handrail Arm Ø25x1.8

Left Handrail

Right Handrail

Left Foot Bar

Right Foot Bar

Front Stabilizer Ø50x1.5x470

9 Rear Stabilizer Ø50x1.5x470

10 Seat Post

1

1

1

1

1

1

1

1

1

1

Qty No.

Description

28 Washer Ø8xØ20x2

29 Seat Cushion DD-PU981T

30 Eyebolt M86x33

31 Tension Bracket

32 Nut M6

33 Flange Nut M10x1

34 Fan Wheel Axle

35 Hexagon Nut M10x1

36 Sensor with Wire

37 Fan Wheel

11 Handrail Arm End Cap Ø25x1.5

12 Handrail Arm Foam Grip

Ø32xØ23x260

13 Handrail Arm Plastic Bushing

Ø28.5xØ25.4x84

14 Bolt M10x18

6

2

4

38

39

40

Computer

Nut Cap S16

Bolt M10x55 2

15 Spring Washer Ø18xØ10x2

16 Washer Ø28xØ16.2x4xB5

17 Wave Washer Ø28xØ16x1

18 Powder Metal Bushing

Ø24.8xØ16x14

19 Rotation Rod

20 Nut Cap S13

21 Handrail Arm Height Adjustment

Knob

22 Handrail Arm End Cap Ø32x1.5

23 Tension Control Knob

24 Phillips Self Tapping Screw

ST4.8x15

25 Seat Height Adjustment Knob M12 1

26 Seat Post Plastic Bushing 1

27 Nylon Nut M8 3

1

2

2

2

1

1

2

2

2

41 Powder Metal Bushing

Ø14xØ10x10

42

43

Nylon Nut M10

Bolt for left Crank Ø16x89xL23

1 44 Wave Washer Ø28xØ17

10 45 Spring Washer Ø20

46

47

49

50

51

52

53

54

Nylon Nut for left Crank B0.5x20

Nut Cap S18

Bolt for right Crank Ø16x89xL23

Foot Pedal 345x146x40

Bolt M10x45

Bolt M6x48

Transport Wheel Ø23xØ6x32

Nylon Nut M10xL9

4

1

2

4

2

2

6

1

1

2

48 Nylon Nut for right Crank B0.5x20

1

2

2

2

1

4

1

5

2

2

1

1

2

2

3

1

Qty

8535DT PARTS LIST (CONT.)

NOTE: For your convenience, your 2 in 1 Elliptical Trainer has been pre-assembled.

Many items on this list are for parts identification ONLY.

No.

61

62

66

ST4.8x20

Description

55 Stabilizer End Cap Ø50

56 Cap Nut M10

57 Curve Washer Ø10x2.0xØ25xR28 4

58 Bolt M10x57 4

4

4

59 Left Chain cover A

60 Left Chain cover B

1

1

Right Chain cover A

Right Chain cover B

63 Phillips Self Tapping Screw

64 Screw ST4.8x40

65 Screw ST4.2x10

Cover Cap

1

1

8

3

8

2

Qty No.

67

68

69

70

71

72

73

74

75

76

Hexagon Nut 7/8”

Washer Ø34.5xØ23x2.5

Slotted Bearing Nut 7/8”

Bearing

Bearing Cup

Notched Bearing Nut 15/16”

Washer Ø40xØ24x3

Strap

Spring Ø10x1.8x32

Chain

Description

77 Chain Pulley with Crank 1/4”/

Ø205x2.6

78 Square End Cap (30x30)

HARDWARE PACK

1

1

1

2

1

1

2

1

1

1

1

Qty

2

14. M10x18 Bolt (2x) 15. Spring Washer (2x) 16. D Washer (2x)

17. Flat Washer (1x) 19. Rotation Rod (1x) 51. M10x45 Bolt (4x)

49, 44, 45, 48. Right Pedal

Assembly

43, 44, 45, 46. Left Pedal

Assembly

42. M10 Nut (4x) 20. Nut Cap 13 (2x) 56. M10 Cap (4x) 57. Arc Washer (4x)

58. M10x57 Bolt (4x) 47. Nut Cap 18 (2x) 39. Nut Cap 16 (4x)

NOTE: The following instructions use the included tools:

Multi-Hex Tool, Small Allen Wrench, and Large Allen Wrench.

Please locate these and keep on hand to assemble.

STEP 1: ASSEMBLE FRONT AND REAR STABILIZERS

Locate 4x M10 Cap Nuts (56), 4x Arc Washers (57), 4x M10x57 Bolts (58), the Front Stabilizer Bar with Wheels (8), and the Rear Stabilizer Bar (9)

A. Position the Front Stabilizer Bar with Wheels (8) under the Fan Wheel of the bike and align the bolt holes to the frame.

IMPORTANT: When aligning these holes, make sure the dimpled, square openings in the Bar are facing down towards the ground.

B. Attach the Stabilizer Bar to the Main Frame by inserting the bolts up through the Bar. Secure the bolts first with the Arc Washers and then tighten the Cap Nuts down to this assembly.

C. Position the Rear Stabilizer Bar (9) behind the Main Frame and attach this to the Main Frame as described in Section B above.

STEP 2: ATTTACH HANDLE AND PEDAL ASSEMBLIES

Locate 2x M10x18 Bolts (14), 2x Spring Washers (15), 2x D Washers (16), 1x Flat Washer (17),

1x Rotation Rod (19), Left Hand Rail/Foot Bar (4, 6), Right Hand Rail/Foot Bar (5, 7), The Left & Right

Pedal Assemblies, and 2x Nut Caps S18 (47)

A. Place the Rotation Rod through the hole in the front of the Main Frame above the Fan Wheel.

Slide the Left and Right Hand Rails (4, 5) onto the exposed ends of the Rotation Rod.

NOTE: The Washers and Hardware may be attached to the Rotation Rod at the factory.

1. Assemble the LEFT Upper Handrail to the Rotation Rod with the hardware in the following order:

1st: 1x Flat Washer (17), 2nd: 1x D Washer (16), 3rd: 1x Spring Washer (15) and Secure with 1x

M10x18 Bolt (14).

2. Assemble the RIGHT Upper Handrail to the Rotation Rod with the hardware in the following order:

1st: 1x D Washer (16), 2nd: 1x Spring Washer (15) and Secure with 1x M10x18 Bolt (14).

B. Once the Upper Hand Rails have been secured, Attach the Lower Foot Bars (6, 7) to the Pedal

Crank using the Left and Right Pedal Assemblies. The ends of these assemblies will be stamped with a “L” or an “R” indicating which side they are to be used on. Note: The Pedal Assemblies are threaded in the same manner as a bicycle pedal, and one will need to be rotated in the opposite direction than a normal screw to tighten.

Assemble the LEFT Lower Handrail to the Pedal Crank:

1. Place a Wave Washer (44) onto the stamped Bolt.

2. Thread this Bolt and Washer through the hole in the Left Lower Foot Bar (6).

3. Once the Bolt is through, slide a Spring Washer onto the other end of the Bolt.

4. Secure with the Hex Nut (46)

(Part 48 for the R side) from the Left Pedal Assembly.

5. Once Tightened, Cover with a Nut Cap S18 (47)

C. Repeat the above steps to attach the Right Foot Bar using the Right Pedal Assembly.

STEP 3: ASSEMBLE PEDALS

Locate 2x Foot Pedals (50), 4x M10x45 Bolts (51), 4x M10 Nuts (42), and 4x Nut Caps S16 (39)

A. Line up the holes on each Foot Pedal to the two holes in the Lower Foot Bar. Thread 2x M10x45

Bolts through each pedal, making sure that the Bolt heads are flush to the Foot Pedal surface. Secure with 2x M10 Nuts.

B. Cover the exposed joints leading from the Lower Foot Bars to the Upper Handrails with 4x Nut

Caps S16; Place one Nut Cap on each side of each Foot Bar.

STEP 3: ASSEMBLE SEAT, HANDLE GRIPS, AND MONITOR

Locate Seat Cushion (29), Seat Post (10), Seat Adjustment Knob (25), 2x Handle Adjustment Knobs

(21), Monitor (38), and the Left and Right Handle Grips (2, 3).

A. Remove the Hex Nuts and Washers from underneath the Seat Cushion (29). Guide the exposed bolts on the Seat Cushion underside through the 3 holes in the Seat Post (10). Place a washer against the plate on the Seat Post and secure with the Hex Nuts.

B. Place the assembled Seat Cushion/Seat Post into the rectangular hole in the top on the unit.

Carefully lower this assembly and secure with the Seat Adjustment Knob (25). Be sure to watch for pinch points in case the seat suddenly drops. Before continuing, make sure that this assembly is secure, and the knob is extended through one of the holes in the post.

C. Insert a Handle Grip (2, 3) down into the opening on the top of each Upper Handrail.

Secure this connection with 1x Handrail Arm Adjustment Knob (21). Make sure the you insert the

Adjustment Knob from opening that is closest to the seat (the Rear). Once inserted, cover the Hex weld on the front of the Handle Grip opposite the Adjustment Knob with a Nut Cap S13 (20).

Repeat the above instructions to attach the remaining Handle Grip.

D. Connect the Sensor Wire (36) to the short wire which extends from the back of the Monitor (38).

Once this connection is secure, slide the Monitor onto the short metal tab in between the Handles until it locks into place. Make sure that the wires are not contacting any moving parts, and ensure that this wire is kept away from the Fan Wheel and the Handle assembly.

FUNCTION BUTTONS:

METER INSTRUCTIONS

MODE: This button cycles through the available Displays and turns the unit ON. Press and hold this button for 3-4 seconds to reset the data values of the monitor.

NOTE: When the batteries are replaced, ALL values will reset to ZERO automatically.

FUNCTIONS & OPERATIONS

1.Battery Installation:

This meter takes 2 x AA 1.5V batteries. Install batteries under the cover in the rear of the meter.

Note: Replacing the batteries will reset ALL values on the meter to ZERO.

2.Auto On/Off:

The system turns on when the MODE key is pressed or when you begin to pedal the bike.

The system turns off automatically approximately 4 minutes after you have stopped using the unit.

Display Specifications

1. SPEED-------------------------0~99.9 (Speed travelled)

2. CALORIE---------------- 0~99.99 (Calories burned)

3. DISTANCE---------------- 0~99.99 (Distance traveled)

4. SCAN------------------------3 SEC (Displays data (rotating) from all modes)

5. TIME----------------------- 0:00~99:59 (Duration of exercise)

Note:

1.If the computer displays data abnormally, please remove the batteries and try again.

2.Battery Spec: 1.5V AA (2PCS).

3.The batteries must be removed from the appliance before it is scrapped and disposed of per local ordinance.

USING YOUR 2 in 1 Elliptical Trainer

ALWAYS consult a physician before beginning any exercise program. Ask your doctor to evaluate your present fitness level and determine the exercise program that is most appropriate for your particular age and/or physical condition.

TO USE THE 2 in 1 Elliptical Trainer:

Stand on the unit, making sure that each foot is securely positioned on each Pedal and that you have sure footing on the Pedal pads (Do not use this machine barefoot or with socks only.) Firmly grasp the

Poles in each hand, and using the Poles only, move them back and forth so that the machine begins to pedal in a forward fashion. Once it is fully in motion, you can begin using your leg muscles to assist in pedaling. It is strongly recommended that you do not attempt to use this machine in a reverse direction.

You can also mount the 2 in 1 Elliptical Trainer like a bicycle. With your body securely centered on the seat, use your leg muscles to move the pedals.

NEVER attempt to suddenly stop pedaling or switch the direction of pedaling while moving, as serious injury and/or severe damage to the unit can occur, for which Pure Global is not liable.

TO INCREASE THE RESISTANCE ON YOUR 2 in 1 Elliptical Trainer:

Use the Tension Control Knob to adjust the resistance on the 2 in 1 Elliptical Trainer. Turn the knob towards the “+” to increase the resistance and “-” to decrease the resistance.

Warm-up

Before every training you should warm-up for 5~10 minutes. Here you can do some stretching and training with low resistance.

Cool down

To introduce an effective cool-down of the muscles and the metabolism, the intensity should be drastically decreased during the last 5~10 minutes, but a prolonged exercise session should not be suddenly and completely stopped. Stretching is also helpful for the prevention of muscle aches.

Training session

The time-length of your training session can be calculated with the following rule of thumb:

Daily training session: approx. 10 min. per unit

2-3 x per week: approx. 30 min. per unit

1-2 x per week: approx. 60 min. per unit

WARM UP/COOL DOWN EXERCISES

WARM UP EXERCISES

A successful exercise program consists of a warm-up, aerobic exercise, and a cooldown. Do the entire program at least two and preferably three times a week, resting for a day between workouts. After several months, you can increase your workouts to four or five times per week.

Warming up is an important part of your workout, and should begin every session. It prepares your body for more strenuous exercise by heating up and stretching out your muscles, increasing your circulation and pulse rate, and delivering more oxygen to your muscles. At the end of your workout, repeat these exercises to reduce sore muscle problems. We suggest the following warm-up and cool-down exercises:

Inner Thigh Stretch

Sit with the soles of your feet together with your knees pointing outward. Pull your feet as close into your groin as possible. Gently push your knees towards the floor. Hold for 15 counts.

Hamstring Stretch

Sit with your right leg extended. Rest the sole of your left foot against your right inner thigh. Stretch toward your toe as far as possible. Hold for 15 counts. Relax and then repeat with left leg extended.

Head Roll

Rotate your head to the right for one count, feeling the stretch up the left side of your neck. Next, rotate your head back for one count, stretching your chin to the ceiling and letting your mouth open.

Rotate your head to the left for one count, and finally, drop your head to your chest for one count.

Shoulder Lift

Lift your right shoulder up toward your ear for one count. Then lift your left shoulder up for one count as you lower your right shoulder.

14

WARM UP/COOL DOWN EXERCISES

WARM UP EXERCISES CONTINUED

Calf-Achilles Stretch

Lean against a wall with your left leg in front of the right and your arms forward.

Keep your right leg straight and the left foot on the floor; then bend the left leg and lean forward by moving your hips toward the wall. Hold, then repeat on the other side for 15 counts

Toe Touch

Slowly bend forward from your waist, letting your back and shoulders relax as you stretch toward your toes. Reach down as far as you can and hold for 15 counts.

Side Stretch

Open your arms to the side and continue lifting them until they are over your head.

Reach your right arm as far upward toward the ceiling as you can for one count. Feel the stretch up your right side. Repeat this action with your left arm.

15

FREQUENTLY ASKED QUESTIONS

Question: “How should I clean my 2 in 1 Elliptical Trainer?”

Answer: YOU SHOULD CLEAN THE TRAINER WITH A SOLUTION OF WARM WATER AND

NON-CORROSIVE AND/OR NON-ABRASIVE SOAP. DAMPEN A RAG WITH THIS SOLUTION AND

WIPE COMPLETELY DRY BEFORE USING.

Question: “Is there any maintenance I need to do for my 2 in 1 Elliptical Trainer?”

Answer: YOU SHOULD ALWAYS DOUBLE CHECK TO MAKE SURE ALL YOUR BOLTS ARE

TIGHT AND SECURE, THE ELLIPTICAL POLES AND PEDALS ARE SECURELY ATTACHED, AND

THE MACHINERY IS MOVING FREELY AND SMOOTHLY. IF YOU NOTICE ANYTHING

UNUSUAL ABOUT THE OPERATION OF YOUR MACHINERY, OR FIND ANY MISSING OR

DAMAGED PARTS, CEASE USE OF THE UNIT IMMEDIATELY AND CONTACT CUSTOMER SER-

VICE AT: [email protected] OR BY CALLING 866-498-5269.

Question: “Something was missing from the packaging,” “I need to purchase a replacement part” or “I discovered a damaged piece. What should I do?”

Answer: CONTACT CUSTOMER SERVICE AT: [email protected] or by calling

866-498-5269. YOU MUST HAVE YOUR PROOF OF PURCHASE AND/OR ORDER

CONFIRMATION AVAILABLE TO BE CONSIDERED FOR WARRANTY REPLACEMENT. YOU

MUST REPORT MISSING PIECES WITHIN 30 DAYS FROM DATE OF PURCHASE. PLEASE BE

AWARE THAT UNDER OUR LIMITED WARRANTY, FOR SOME PARTS WE REQUIRE A PICTURE

OF THE DAMAGED ITEM AND/OR RETURN OF THE DAMAGED ITEM(S) TO OUR QUALITY

CONTROL OFFICE FOR REVIEW.