3. Hang Display onto the Wall Plate
wall wall
INSTALLATION INSTRUCTIONS
Tilting Wall Mount
Tighten bottom bolts to secure display brackets to the wall plate.
4. Adjustment
Tilt adjusting knob
Bolt
0°
-10°
7
Loose the adjusting knobs to tilt desired angle then tighten them.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.
PT-124
PT-144
200x200/400x200
200x200/300x300
400x200/400x400
CAUTION: DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
42"
MAX
75kg
(165lbs)
MAX 47"
MAX
ISSUED: OCT.2012
1
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any question
regarding any of the instruction or warning, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experience and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If
any parts are missing or faulty, telephone your local distributor for a replacement.
Package M wall plate (x1)
A left adapter bracket (x1)
B right adapter bracket (x1)
C
M5x14 (x4)
M-A
M6x14 (x4)
M-B
M8x20 (x4)
M-C
M6x30 (x4)
M-D washer (x4)
M-F small spacer (x8)
M-G big spacer (x4)
M-H
M8x30 (x4)
M-E
Package W
ST6.3x55 (x4)
W-A concrete anchor (x4)
W-B
D6 washer (x4)
W-C
2
1a. Mount on Wood Stud Wall
W-C
W-A
55mm
1
ø 4.5mm
(ø 3/16")
2
Find and mark the exact location of mounting holes
3
Drill pilot holes
1b. Mount on Solid Brick and Concrete Block
60mm
( (2.4") )
ø 10mm
(ø 3/8" )
Mark the exact location of mounting holes
1
2
Drill pilot holes
W-B
W-C
W-A
√ X X
√ X X
Screw the wall plate onto the wall
Screw the wall plate onto the wall
3
WARNING
• Make sure that mounting screws are anchored into the center of the studs. The use of a stud
finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
WARNING
• When installing wall mounts on cinder block, verify the actual concrete thickness is at least
1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure to
mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block.
It is suggested electric drill on slow setting be used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
4
5
2. Install Adapter Brackets
Top of display
2-2 For Recessed Back Screen or to Access A/V Inputs
TV
TV
TV
2-1 For Flat Back Screen
TV
TV
TV
M-A
M-B
M-C
M-F M-C
M-F or
M-G
M-C
M-D
M-E
M-F or
M-G
M-G
M-D
M-E
M-F or
M-H
M-D
M-E
M-F
M-G
M-H
Note: Choose appropriate screws, washers and spacers (if necessary) according to the type of screen.
·
Position the adapter brackets as close as possible to the center of the display.
· Screw the adapter brackets onto the display.
Tighten all screws but do not over tighten.
6
