advertisement
OWNERS MANUAL
PMX401
4 CHANNELS
6 CHANNELS PMX601
PMX802
8 CHANNELS www.pyleaudio.com
1
FEATURES AT A GLANCE
4,6,8 Balanced microphone inputs, 4,6,8 high impedance microphone/line
Inputs and Tape/CD inputs. All may be used simultaneously. Reverb built in with individual control on each channel line out for connection to external amplifiers. Record out jack for taping performances. R.F interference protection on all inputs and outputs.
The powered mixer is not only easy to use and transport, but designed with the latest technology. The is designed with a strong metal structure, wood cabinet, with vinyl surface, and metal corners. This makes the ideal powered mixer.
2
SAFETY INSTRUCTIONS
CAUTION: To reduce the risk of electrical shock, do not remove the cover (or back). No user serviceable parts inside; refer servicing to qualified personnel.
WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture.
This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage.
Inside the enclosure-voltage that may be sufficient to constitute a risk of shock
This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Read the manual.
3
A. FRONT PANEL SECTION FEATURES
1. BALANCE INPUT (MIC)
Electronic Balanced inputs acceptable a standard XLR male connector. It is designed to accept a
4
balanced low impedance input signal, Phantom power (15 volts) for condenser microphones is always on and available. It has an input impedance of 1K ohm. The connector is wired as: Pin= shield ; Pin3= negative(cold).
2. BALANCE INPUT(LINE)
Electronic Balanced inputs acceptable a standard 1/4
"
jacks connector. It is designed to accept a balanced high impedance input signal (This use for connection Deck , Turntable, Keyboard etc
… ).
3. VOLUME
This is function to adjust the volume of signal connection into each channel and adjust the volume of output, together with master fader.
4. TREBLE
This control gives you up to 15 db of boost or cut at 10 kHz and above, and it is also flat at the detent.
Use it to add sizzle to cymbals, and an overall sense of transparency or edge to key-boards, vocals, guitar, and bacon frying. Turn it down a little to reduce sibilance, or to hide tape hiss.
5. LOW
This control gives you up to 15 dB boost or cut at 100Hz and below. This circuit is flat (no boost or cut) at the center detent position. This frequency represents the punch in bass drums, bass guitar, fat synch patches, and some really serious male singers.
5
6. EFF
This is a send control to the reverb buss, It controls the amount of reverberation added to the input
Signals.
7. GRAPHIC EQUALIZER
2
×5-band equalizer is provided for tone control over each frequency , and for precise high quality sound by final tone control. It can control main channel and rec channel.( 60,250,1K,2K,8KHz ) shelving at +/-12dB).
8. VOLUME
Using by this control, you can adjust signal level of phone.
9. PHONE
Phone output jack.
10. OUTPUTS LEVEL INDICATOR
This is level meter which shows output levels of left & right channel condition on the way of operation, therefore, you can see output condition thru this master level indication.
11.POWER LED
It lights when power switch turn on.
6
12. PHANTOM LED
The LED +15V will be turned on when start working.
13. PHANTOM POWER SWITCH
When it is depressed, the XLR jack input has +15V voltage.
14.EFF DELAY
Using by this control, you can adjust the delay time interval of echo repeat.
15. EFF REPEAT
Using by this control , you can adjust
reverberating deepness.
16. EFF LEVEL
Using by this control, you can adjust signal level of echo output.
17. MASTER VOLUME
Using by this control, you can adjust signal level of main channel.
18. TAPE
7
This controls the level of the playback inputs(RCA) jack.
19.TAPE INPUT
These RCA jacks are for brining in a tape deck, CD play or other line level source. The impedance
Is 10k ohms .
20. REC OUTPUT
These RCA jacks are for hooking up a tape desk to record from the mixer. Both channel are summed into mono for compatibility. The signals are taken pre-master section, meaning that they are without reverb or the master tone section, and does not include the Tape in signal, The impedance is 1K ohms
@ -10dBv.
8
1. SPEAKER JACK (LEFT/RIGHT)
These are 2 conductor 1/4” speaker outputs. Each one is rated at 8 ohm minimum impedance. Total minimum load for the amplifier is 4 ohms. You may comment either 1-4 ohm. 1-8 ohm or 2-8 ohm speaker cabinets. Do not below rated minimum impedance.
2. SEND/RETURN
9
Using by this jack, you can use stereo 1/4
" jacks connector send internal signal which before power amplifier to external effects processing, after processing return to internal power amplifier.
Or you can use stereo or mono 1/4
" jacks connector send external signal to inner power amplifier .
3. POWER SWITCH
when you want to operate, turn on it, then the LED will be turned on .
4. AC POWER CORD/FUSE HOLDERS
AC 220
~240V 60Hz or 110-120V 60Hz ,Check the power voltage of supply with silk-screen of the panel before connections. When occur a problem on this appliance, the fuse will be cut off, power to prevent form a problem.
5. FAN
In order to prevent rising the inside temperature, the inside heat is emitted outside.
10
C.CONNECTIONS
You will need a lot of cables for different purposes – see the following figures to make sure you have got the right ones. Unbalanced equipment may be connected to balanced inputs/outputs. Either use mono 1/4
"
jacks or connect ring and sleeve of TRS jacks.
11
12
Speaker Connections
VERY IMPORTANT, PLEASE READ BEFORE CONNECTING SPEAKERS.
One or more speakers (2, 4, or 8 ohm) can be connected to the amplifier with or without transformers.
However, before you connect any speaker to the amplifier, the total speaker impedance must be calculated in order to avoid damage to the amplifier. A total speaker impedance greater than 16 ohms or less than 4 ohms can damage your amplifier. To start, all connected speakers should have the same impedance.
Please refer to the following diagrams for instructions on connecting more than one speaker. Take special note of the type of connection (parallel vs. serial) and the impedance of the connected speakers.
13
D.APPENDIX
Bandwidth 20Hz to 20kHz_+ 1dB
Input Impedance: Lo-Z Mic 1K ohms
Hi-Z Mic/Line 33K ohms
Tape playback 10K ohms
Phone 51 ohms
Input level: Lo-Z Mic -50dB
Hi-Z Mic/Line -20dB
Tape playback -10dB
Bandwidth 20Hz to 20kHz_+ 1dB
Rec output level +22dB(max)
Phone output level +22dB(max)
17
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project